MATERIAL SAFETY DATA SHEET
MSDS No. M0176 Effective Date: 02/11/2002
1. CHEMICAL PRODUCT AND COMPANY IDENTIFICATION
Product Group: REFRACTORY CERAMIC FIBER PRODUCT
Chemical Name: VITREOUS ALUMINOSILICATE FIBER
RCF, ceramic fiber, synthetic vitreous fiber (SVF), man-made vitreous fiber (MMVF),
Synonym(s):
man-made mineral fiber (MMMF)
Trade Names: ANCHOR-LOC®2 CERAMIC FIBER MODULES
ANCHOR-LOC®2 2200 CERAMIC FIBER MODULES
Power-Loc®2 22; Screw-Loc®2 22; Thread-Loc®2 22; Weld-Loc®2 22.
Fibermassâ„? Block 22
ANCHOR-LOC®2 2600 CERAMIC FIBER MODULES
Power-Loc®2 26; Screw-Loc®2 26; Thread-Loc®2 26; Weld-Loc®2 26.
Fibermassâ„? Block 26
Manufacturer/Supplier: Unifrax Corporation
2351 Whirlpool St.
Niagara Falls, NY 14305-2413
Product Stewardship Information Hotline
1-800-322-2293 (Monday - Friday 8:00 a.m. - 4:30 p.m. EST)
For additional MSDSs, visit our web page, http: //www.unifrax.com, or call Unifrax
Customer Service at (716) 278-3872
CHEMTREC Assist: CHEMTREC will provide assistance for chemical emergencies. Call 1-800-424-9300
2. COMPOSITION / INFORMATION ON INGREDIENTS
COMPONENTS CAS NUMBER % BY WEIGHT
Refractories, Fibers, Aluminosilicate (with zirconia) 142844-00-6 98-99
Oxirane, methyl-, polymer with oxirane, 9038-95-3 1-2
monobutyl ether
(See Section 8 "Exposure Controls / Personal Protection" for exposure guidelines)
3. HAZARDS IDENTIFICATION
EMERGENCY OVERVIEW
WARNING!
POSSIBLE CANCER HAZARD BY INHALATION.
(See Section 11 for more information)
CHRONIC EFFECT
There has been no increased incidence of respiratory disease in studies examining occupationally exposed workers.
1
In animal studies, long-term laboratory exposure to doses hundreds of times higher than normal occupational
exposures has produced fibrosis, lung cancer, and mesothelioma in rats or hamsters. The fibers used in those
studies were specially sized to maximize rodent respirability.
OTHER POTENTIAL EFFECTS
TARGET ORGANS:
Respiratory Tract (nose & throat), Eyes, Skin
RESPIRATORY TRACT (nose & throat) IRRITATION:
If inhaled in sufficient quantity, may cause temporary, mild mechanical irritation to respiratory tract. Symptoms may
include scratchiness of the nose or throat, cough or chest discomfort.
EYE IRRITATION:
May cause temporary, mild mechanical irritation. Fibers may be abrasive; prolonged contact may cause damage to the
outer surface of the eye.
SKIN IRRITATION:
May cause temporary, mild mechanical irritation. Exposure may also result in inflammation, rash or itching.
GASTROINTESTINAL IRRITATION:
Unlikely route of exposure.
MEDICAL CONDITIONS AGGRAVATED BY EXPOSURE:
Pre-existing medical conditions, including dermatitis, asthma or chronic lung disease may be aggravated by exposure;
individuals who have a history of allergies may experience greater amounts of skin and respiratory irritation.
HAZARD CLASSIFICATION
Although studies, involving occupationally exposed workers, have not identified any increased incidence of respiratory
disease, results from animal testing have been used as the basis for hazard classification. In each of the following
cases, the conclusions are qualitative only and do not rest upon any quantitative analysis suggesting that the hazard
actually may occur at current occupational exposure levels.
In October 2001, the International Agency for Research on Cancer (IARC) confirmed that Group 2b (possible
human carcinogen) remains the appropriate IARC classification for RCF.
The Seventh Annual Report on Carcinogens (1994), prepared by the National Toxicology Program (NTP),
classified respirable RCF and glasswool as substances reasonably anticipated to be carcinogens.
The American Conference of Governmental Industrial Hygienists (ACGIH) has classified RCF as “A2-Suspected
Human Carcinogen.�
The Commission of The European Communities (DG XI) has classified RCF as a substance that should be
regarded as if it is carcinogenic to man.
The State of California, pursuant to Proposition 65, The Safe Drinking Water and Toxic Enforcement Act of 1986,
has listed "ceramic fibers (airborne fibers of respirable size)" as a chemical known to the State of California to cause
cancer.
The Canadian Environmental Protection Agency (CEPA) has classified RCF as "probably carcinogenic" (Group 2).
The Canadian Workplace Hazardous Materials Information System (WHMIS) � RCF is classified as Class D2A �
Materials Causing Other Toxic Effects
The Hazardous Materials Identification System (HMIS) �
Health 1* Flammability 0 Reactivity 0 Personal Protection Index: X (Employer Determined)
(* denotes potential for chronic effects)
2
2
4. FIRST AID MEASURES
FIRST AID PROCEDURES
RESPIRATORY TRACT (nose & throat) IRRITATION:
If respiratory tract irritation develops, move the person to a dust free location. Get medical attention if the irritation
continues. See Section 8 for additional measures to reduce or eliminate exposure.
EYE IRRITATION:
If eyes become irritated, flush immediately with large amounts of lukewarm water for at least 15 minutes. Eyelids
should be held away from the eyeball to ensure thorough rinsing. Do not rub eyes. Get medical attention if irritation
persists.
SKIN IRRITATION:
If skin becomes irritated, remove soiled clothing. Do not rub or scratch exposed skin. Wash area of contact
thoroughly with soap and water. Using a skin cream or lotion after washing may be helpful.
GASTROINTESTINAL IRRITATION:
If gastrointestinal tract irritation develops, move the person to a dust free environment.
NOTES TO PHYSICIANS:
Skin and respiratory effects are the result of temporary, mild mechanical irritation; fiber exposure does not result in
allergic manifestations.
5. FIRE FIGHTING MEASURES
NFPA Codes: Flammability: 0 Health: 1 Reactivity: 0 Special: 0
NFPA Unusual Hazards: None
Flammable Properties: None
Flash Point: None
Hazardous Decomposition Products:
may release smoke, carbon monoxide, and carbon dioxide. Use
adequate ventilation or other precautions to eliminate exposure to
vapors resulting from thermal decomposition of binder. Exposure to
thermal decomposition fumes may cause respiratory tract irritation,
bronchial hyper-reactivity or an asthmatic-type response.
Unusual Fire and Explosion Hazard: None
Extinguishing Media: Use extinguishing media suitable for type of surrounding fire.
6. ACCIDENTAL RELEASE MEASURES
SPILL PROCEDURES
Avoid creating airborne dust. Dust suppressing cleaning methods such as wet sweeping or vacuuming should be
used to clean the work area. If vacuuming, the vacuum must be equipped with a HEPA filter. Compressed air or dry
sweeping should not be used for cleaning.
7. HANDLING AND STORAGE
STORAGE
Store in original container in a dry area. Keep container closed when not in use.
HANDLING
3
3
Handle ceramic fiber carefully. Limit use of power tools unless in conjunction with local exhaust. Use hand tools
whenever possible. Frequently clean the work area with HEPA filtered vacuum or wet sweeping to minimize the
accumulation of debris. Do not use compressed air for clean-up.
EMPTY CONTAINERS
Product packaging may contain residue. Do not reuse.
8. EXPOSURE CONTROLS/PERSONAL PROTECTION
EXPOSURE GUIDELINES
COMPONENTS OSHA PEL MANUFACTURER REG
Refractories, Fibers, Aluminosilicate None Established* 0.5 f/cc, 8-hr. TWA**
(with zirconia)
* There is no specific regulatory standard for RCF in the U.S. OSHA’s “Particulate Not Otherwise Regulated
(PNOR)� standard [29 CFR 1910.1000, Subpart Z, Air Contaminants] applies generally; Total Dust 15 mg/m³
; Respirable Fraction 5 mg/m³.
** The Refractory Ceramic Fibers Coalition (RCFC) has sponsored comprehensive toxicology and
epidemiology studies to identify potential RCF-related health effects [see Section 11 for more details],
consulted experts familiar with fiber and particle science, conducted a thorough review of the RCF-related
scientific literature, and further evaluated the data in a state-of-the-art quantitative risk assessment. Based
on these efforts and in the absence of an OSHA PEL, RCFC has adopted a recommended exposure
guideline, as measured under NIOSH Method 7400 B. The manufacturers� REG is intended to promote
occupational health and safety through prudent exposure control and reduction and it reflects relative
technical and economic feasibility as determined by extensive industrial hygiene monitoring efforts
undertaken pursuant to an agreement with the U.S. Environmental Protection Agency.
OTHER OCCUPATIONAL EXPOSURE LEVELS (OEL)
RCF-related occupational exposure limits vary internationally. Regulatory OEL examples include: Australia � 0.5
f/cc; Austria � 0.5 f/cc; Canada � 0.5 to 1.0 f/cc; Denmark � 1.0 f/cc; France � 0.6 f/cc; Germany � 0.5 f/cc;
Netherlands � 1.0 f/cc; New Zealand � 1.0 f/cc; Norway � 2.0 f/cc; Poland � 2.0 f/cc; Sweden � 1.0 f/cc; United
Kingdom � 2.0 f/cc. Non-regulatory OEL examples include: ACGIH TLV 0.2 f/cc; RCFC REG 0.5 f/cc. The
objectives and criteria underlying each of these OEL decisions also vary. The evaluation of occupational exposure
limits and determining their relative applicability to the workplace is best performed, on a case-by-case basis, by a
qualified Industrial Hygienist.
EXPOSURE GUIDELINES -- OTHER INGREDIENTS
COMPONENTS OSHA PEL MANUFACTURER REG
None established None established
Oxirane, methyl-, polymer with
oxirane, monobutyl ether
OTHER OCCUPATIONAL EXPOSURE LEVELS (OEL)
Non-regulatory OEL examples include: ACGIH TLVs (TWAs): Oxirane, methyl-, polymer with oxirane, monobutyl
ether -- None established.
ENGINEERING CONTROLS
Use engineering controls such as local exhaust ventilation, point of generation dust collection, down draft work
stations, emission controlling tool designs, and materials handling equipment designed to minimize airborne fiber
emissions.
4
4
PERSONAL PROTECTION EQUIPMENT
Respiratory Protection � RCF:
When engineering and/or administrative controls are insufficient to maintain workplace concentrations within the 0.5
f/cc REG, the use of appropriate respiratory protection, pursuant to the requirements of OSHA Standards 29 CFR
1910.134 and 29 CFR 1926.103, is recommended. The following information is provided as an example of
appropriate respiratory protection for aluminosilicate fibers. The evaluation of workplace hazards and the
identification of appropriate respiratory protection is best performed, on a case by case basis, by a qualified Industrial
Hygienist.
MANUFACTURER’S RESPIRATORY PROTECTION RECOMMENDATIONS
WHEN HANDLING RCF PRODUCTS
�
Respirable Airborne Fiber Concentration
Respirator Recommendation
(levels are 8-hr. time-weighted averages)
Not yet determined but expected to be below 5.0 f/cc Half-face, air purifying respirator equipped with a NIOSH
based on operation certified P100 particulate filter cartridge
"Reliably" less than 0.5 f/cc Optional
0.5 f/cc to 5.0 f/cc Half-face, air purifying respirator equipped with a NIOSH
certified P100 particulate filter cartridge
5.0 f/cc to 25 f/cc Full-facepiece, air purifying respirator equipped with a
NIOSH certified P100 particulate filter cartridge or PAPR
Greater than 25 f/cc PAPR with tight-fitting full facepiece or a supplied air
respirator in continuous flow mode
When individual workers request respiratory protection as A NIOSH certified respirator, such as a disposable
a matter of personal comfort or choice where exposures particulate respirator, or respirators with filter cartridges
are "reliably" below 0.5 f/cc rated N95 or better
�
The P100 recommendation is a conservative default choice; in some case, solid arguments can be made that other
respirator types (e.g., N95, R99, etc.) may be suitable for some tasks or work environments. The P100
recommendation is not designed to limit informed choices, provided that respiratory protection decisions comply with
29 CFR 1910.134.
Other Information:
Concentrations based upon an eight-hour time weighted average (TWA) as determined by air samples collected
and analyzed pursuant to NIOSH method 7400 (B) for airborne fibers.
The manufacturer recommends the use of a full-facepiece air purifying respirator equipped with an appropriate
particulate filter cartridge during furnace tear-out events and the removal of used RCF to control exposures to
airborne fiber and the potential presence of crystalline silica. If exposure levels are known, the respiratory
protection chart provided above may be applied.
Potential exposure to other airborne contaminants should be evaluated by a qualified Industrial Hygienist for the
selection of appropriate respiratory protection and air monitoring.
Skin Protection:
Wear gloves, head coverings and full body clothing as necessary to prevent skin irritation. Washable or disposable
clothing may be used. If possible, do not take unwashed clothing home. If soiled work clothing must be taken home,
employers should ensure employees are thoroughly trained on the best practices to minimize or avoid non-work dust
exposure (e.g., vacuum clothes before leaving the work area, wash work clothing separately, rinse washer before
washing other household clothes, etc.).
5
5
Eye Protection:
Wear safety glasses with side shields or other forms of eye protection in compliance with appropriate OSHA
standards to prevent eye irritation. The use of contact lenses is not recommended, unless used in conjunction with
appropriate eye protection. Do not touch eyes with soiled body parts or materials. If possible, have eye-washing
facilities readily available where eye irritation can occur.
9. PHYSICAL AND CHEMICAL PROPERTIES
White, odorless, fibrous material
ODOR AND APPEARANCE:
Vitreous Aluminosilicate Fibers
CHEMICAL FAMILY:
Not Applicable
BOILING POINT:
Not Soluble in Water
WATER SOLUBILITY (%):
1760° C (3200° F)
MELTING POINT:
2.50 � 2.75
SPECIFIC GRAVITY:
Not Applicable
VAPOR PRESSURE:
Not Applicable
pH:
Not Applicable
VAPOR DENSITY (Air = 1):
Not Applicable
% VOLATILE:
Not Applicable
MOLECULAR FORMULA:
10. STABILITY AND REACTIVITY
Stable under conditions of normal use.
CHEMICAL STABILITY:
INCOMPATIBILITY:
None.
CONDITIONS TO AVOID:
Thermal decomposition of binder from fires or from first heat of
HAZARDOUS DECOMPOSITION PRODUCTS:
product may release smoke, carbon monoxide, and carbon dioxide.
vapors resulting from thermal decomposition of binder. Exposure to
thermal decomposition fumes may cause respiratory tract irritation,
bronchial hyper-reactivity or an asthmatic-type response.
Not Applicable.
HAZARDOUS POLYMERIZATION:
11. TOXICOLOGICAL INFORMATION
HEALTH DATA SUMMARY
Epidemiological studies of RCF production workers have indicated no increased incidence of respiratory
disease nor other significant health effects. In animal studies, long-term, high-dose inhalation exposure
resulted in the development of respiratory disease in rats and hamsters.
EPIDEMIOLOGY
The University of Cincinnati is conducting an ongoing epidemiologic investigation. The evidence obtained from
employees in U. S. RCF manufacturing facilities is as follows:
1) There is no evidence of any fibrotic lung disease (interstitial fibrosis) from evaluations of chest X-rays.
2) There is no evidence of an elevated incidence of lung disease among RCF manufacturing employees.
3) In early studies, an apparent statistical “trend� was observed, in the exposed population, between RCF exposure
duration and some measures of lung function. The observations were clinically insignificant. If these observations
6
6
were made on an individual employee, the results would be interpreted as being within the normal (predicted)
respiratory range. A more recent longitudinal study of employees with 5 or more pulmonary function tests found that
there was no effect on lung function associated with RCF production experience. Initial data (circa 1987) seemed to
indicate an interactive effect between smoking and RCF exposure; more recent data, however, found no interactive
effect. Nevertheless, to promote good health, RCF employees are still actively encouraged not to smoke.
4) Pleural plaques (thickening along the chest wall) have been observed in a small number of RCF employees. Some
studies appear to show a relationship between the occurence of pleural plaques on chest radiographs and the
following variables: (a) years since RCF production hire date; (b) duration of RCF production employment; and (c)
cumulative RCF exposure. The best evidence to date indicates that pleural plaques are a marker of exposure only.
Pleural plaques are not associated with pulmonary impairment. The pathogenesis of pleural plaques remains
incompletely understood; however, the mechanism appears to be an inflammatory response caused by inhaled fibers.
TOXICOLOGY
A number of toxicological studies designed to identify any potential health effects from RCF exposure have been
completed. In one study, conducted by the Research and Consulting Company, (Geneva, Switzerland), rats and
hamsters were exposed to 30 mg/m³ (about 200 fibers/cc) of specially-prepared RCF for 6 hours/day, 5 days/week,
for up to 24 months. In rats, a statistically significant increase in lung tumors was observed; two mesotheliomas
(cancer of the pleural lining between the chest wall and lung) were also identified. Hamsters did not develop lung
tumors; however, interstitial fibrosis and mesothelioma was found. Some, in the scientific community, have
concluded that the “maximum tolerated dose� was exceeded and that significant particle contamination was a
confounding issue; therefore, these study findings may not represent an accurate assessment of the potential for RCF
to produce adverse health effects.
In a related multi-dose study with a similar protocol, other rats were exposed to doses of 16 mg/m³, 9 mg/m³, 3
mg/m³ which corresponds to about 115, 75, and 25 fibers per cubic centimeter respectively. This study found no
statistically significant increase in lung cancer. Some cases of pleural and parenchymal fibrosis were seen in the 16
mg/m³ dose group. Some cases of mild fibrosis and one mesothelioma were observed in the 9 mg/m³ group. No
acute respiratory effects were seen in the rats in the 3 mg/m³ exposure group, which suggests that there may be a
dose/response threshold, below which irreversible respiratory impacts do not occur.
Other toxicological studies have been conducted which utilized non-physiological exposure methods such as
intrapleural, intraperitoneal and intratracheal implantation or injection. Some of these studies have found that RCF is
a potential carcinogen. Some experts, however, suggest that these tests have limited relevance because they bypass
many of the biological mechanisms that prevent fiber deposition or facilitate fiber clearance.
To obtain more epidemiology or toxicology information, please call the toll free telephone number for the Unifrax
12. ECOLOGICAL INFORMATION
No ecological concerns have been identified.
13. DISPOSAL CONSIDERATIONS
7
7
WASTE MANAGEMENT
To prevent waste materials from becoming airborne during waste storage, transportation and disposal, a covered
container or plastic bagging is recommended.
DISPOSAL
RCF, as manufactured, is not classified as a hazardous waste according to Federal regulations (40 CFR 261). Any
processing, use, alteration or chemical additions to the product, as purchased, may alter the disposal requirements.
Under Federal regulations, it is the waste generator's responsibility to properly characterize a waste material, to
determine if it is a "hazardous" waste. Check local, regional, state or provincial regulations to identify all applicable
disposal requirements.
This product is manufactured with zirconium compounds which may contain trace quantities (<500ppm) of naturally
occurring radioactive material (NORM) consisting of uranium, thorium, and/or radium. The quantity of radioactive
materials in the zirconium compounds is below the regulatory level of 0.05% established by the Nuclear Regulatory
Commission (NRC). Check your local, regional and state or provincial regulations for specific applicable handling and
disposal requirements.
14. TRANSPORT INFORMATION
U.S. DEPARTMENT OF TRANSPORTATION (DOT)
Hazard Class: Not Regulated United Nations (UN) Number: Not Applicable
Labels: Not Applicable North America (NA) Number: Not Applicable
Placards: Not Applicable Bill of Lading: Product Name
INTERNATIONAL
Canadian TDG Hazard Class & PIN: Not regulated
15. REGULATORY INFORMATION
UNITED STATES REGULATIONS
EPA: Superfund Amendments and Reauthorization Act (SARA) Title III - This product does not
contain any substances reportable under Sections 302, 304, 313, (40 CFR 372). Sections 311
and 312 (40 CFR 370) apply (delayed hazard).
Toxic Substances Control Act (TSCA) - All substances in this product are listed, as required,
on the TSCA inventory. RCF has been assigned a CAS number; however, it is a simple
mixture and therefore not required to be listed on the TSCA inventory. The components of
RCF are listed on the inventory.
Comprehensive Environmental Response, Compensation and Liability Act (CERCLA)
and the Clean Air Act (CAA) - RCF contains fibers with an average diameter greater than one
micron and thus is not considered a hazardous air pollutant.
OSHA: Comply with Hazard Communication Standards 29 CFR 1910.1200 and 29 CFR 1926.59
and the Respiratory Protection Standards 29 CFR 1910.134 and 29 CFR 1926.103.
California: Ceramic fibers (airborne particles of respirable size)� is listed in Proposition 65, The Safe
Drinking Water and Toxic Enforcement Act of 1986 as a chemical known to the State of
California to cause cancer.
Other States: RCF products are not known to be regulated by states other than California; however, state
and local OSHA and EPA regulations may apply to these products. If in doubt, contact your
8
8
local regulatory agency.
INTERNATIONAL REGULATIONS
Canada: Canadian Workplace Hazardous Materials Information System (WHMIS) � RCF is
classified as Class D2A � Materials Causing Other Toxic Effects
Canadian Environmental Protection Act (CEPA) - All substances in this product are listed,
as required, on the Domestic Substance List (DSL)
European Union: European Directive 97/69/EC classified RCF as a Category 2 carcinogen; that is it “should be
regarded as if it is carcinogenic to man.�
16. OTHER INFORMATION
RCF DEVITRIFICATION
As produced, all RCF fibers are vitreous (glassy) materials which do not contain crystalline silica. Continued
exposure to elevated temperatures may cause these fibers to devitrify (become crystalline). The first crystalline
formation (mullite) begins to occur at approximately 985° C (1805° F). Crystalline silica (cristobalite) formation may
begin at temperatures of approximately 1200° C (2192° F). The occurrence and extent of crystalline phase
formation is dependent on the duration and temperature of exposure, fiber chemistry and/or the presence of fluxing
agents. The presence of crystalline phases can be confirmed only through laboratory analysis of the "hot face" fiber.
IARC’s evaluation of crystalline silica states “Crystalline silica inhaled in the form of quartz or cristobalite from
occupational sources is carcinogenic to humans (Group 1)� and additionally notes “carcinogenicity in humans was not
detected in all industrial circumstances studied� (IARC Monograph Vol. 68, 1997). NTP lists all polymorphs of
crystalline silica amongst substances which may "reasonably be anticipated to be carcinogens".
IARC and NTP did not evaluate after-service RCF, which may contain various crystalline phases. However, an
analysis of after-service RCF samples obtained pursuant to an exposure monitoring agreement with the USEPA,
found that in the furnace conditions sampled, most did not contain detectable levels of crystalline silica. Other
relevant RCF studies found that (1) simulated after-service RCF showed little, or no, activity where exposure was by
inhalation or by intraperitoneal injection; and (2) after-service RCF was not cytotoxic to macrophage-like cells at
concentrations up to 320 g/cm² - by comparison, pure quartz or cristobalite were significantly active at much lower
levels (circa 20 g/cm²).
PRODUCT STEWARDSHIP PROGRAM
The Unifrax Corporation has established a program to provide customers with up-to-date information regarding the
proper use and handling of refractory ceramic fiber. In addition, Unifrax Corporation has also established a program
to monitor airborne fiber concentrations at customer facilities. If you would like more information about this program,
please call the Unifrax Corporation Product Stewardship Information Hotline at 1-800-322-2293.
On February 11, 2002, the Refractory Ceramic Fibers Coalition (RCFC) and the U.S. Occupational Safety and Health
Administration (OSHA) introduced a voluntary worker protection program entitled PSP 2002, a comprehensive,
multi-faceted risk management program designed to control and reduce workplace exposures to refractory ceramic
fiber (RCF). Unifrax Corporation, as a member of RCFC, is participating in this highly acclaimed product stewardship
program. For more information regarding PSP 2002, please call the Unifrax Corporation's Product Stewardship
Information Hotline at 1-800-322-2293 or refer to the RCFC web site: http://www.rcfc.net.
DEFINITIONS
American Conference of Governmental Industrial Hygienists
ACGIH:
Carriage of Dangerous Goods by Road (International Regulation)
ADR:
Alumino-zirconia-silicate
AZS:
Clean Air Act
CAA:
Chemical Abstracts Service
CAS:
Comprehensive Environmental Response, Compensation and Liability Act
CERCLA:
Domestic Substances List
DSL:
9
9
Environmental Protection Agency
EPA:
European Union
EU:
Fibers per cubic centimeter
f/cc:
High Efficiency Particulate Air
HEPA:
Hazardous Materials Identification System
HMIS:
International Agency for Research on Cancer
IARC:
International Air Transport Association
IATA:
International Maritime Dangerous Goods Code
IMDG:
Milligrams per cubic meter of air
mg/m³:
Million particles per cubic meter
mmpcf:
National Fire Protection Association
NFPA:
National Institute for Occupational Safety and Health
NIOSH:
Occupational Safety and Health Administration
OSHA:
OSHA Respiratory Protection Standards
29 CFR 1910.134 & 1926.103:
OSHA Hazard Communication Standards
29 CFR 1910.1200 & 1926.59:
Permissible Exposure Limit (OSHA)
PEL:
Product Identification Number
PIN:
Particulates Not Otherwise Classified
PNOC:
Particulates Not Otherwise Regulated
PNOR:
Product Stewardship Program
PSP:
Refractory Ceramic Fibers Coalition
RCFC:
Resource Conservation and Recovery Act
RCRA:
Recommended Exposure Guideline (RCFC)
REG:
Recommended Exposure Limit (NIOSH)
REL:
Carriage of Dangerous Goods by Rail (International Regulations)
RID:
Superfund Amendments and Reauthorization Act
SARA:
Emergency Planning and Community Right to Know Act
SARA Title III:
Extremely Hazardous Substances
SARA Section 302:
Emergency Release
SARA Section 304:
MSDS/List of Chemicals and Hazardous Inventory
SARA Section 311:
Emergency and Hazardous Inventory
SARA Section 312:
Toxic Chemicals and Release Reporting
SARA Section 313:
Short Term Exposure Limit`
STEL:
Synthetic Vitreous Fiber
SVF:
Transportation of Dangerous Goods
TDG:
Threshold Limit Value (ACGIH)
TLV:
Toxic Substances Control Act
TSCA:
Time Weighted Average
TWA:
Workplace Hazardous Materials Information System (Canada)
WHMIS:
Revision Summary: Section 3: IARC update, Section 8: Respiratory Protection table expanded, Section 11:
Minor changes, Section 16: Added PSP2002 information.
Consolidation and update of MSDS revised 3/16/98: M0174.
MSDS Prepared By: UNIFRAX RISK MANAGEMENT DEPARTMENT
DISCLAIMER
The information presented herein is presented in good faith and believed to be accurate as of the effective date of this Material
Safety Data Sheet. Employers may use this MSDS to supplement other information gathered by them in their efforts to assure the
health and safety of their employees and the proper use of the product. This summary of the relevant data reflects professional
judgment; employers should note that information perceived to be less relevant has not been included in this MSDS. Therefore,
given the summary nature of this document, Unifrax Corporation does not extend any warranty (expressed or implied), assume any
responsibility, or make any representation regarding the completeness of this information or its suitability for the purposes
envisioned by the user.
10
10
More Unifrax High Temperature Insulation Information On The Web:
http://www.unifrax.com
Official Unifrax High Temperature Insulation Website
http://www.high-temperature-insulation.com
Unifrax High Temperature Insulation Information
http://www.refractory-ceramic-fiber.com
Unifrax Refractory Ceramic Fiber Information
Official Fiberfrax Refractory Ceramic Fiber High
http://www.fiberfrax.com
Temperature Insulation Information
Official Foamfrax Advanced High Temperature
http://www.foamfrax.com
Insulation Information
Official Insulfrax Soluble Fiber High Temperature
http://www.insulfrax.com
Insulation Information
Official Isofrax Soluble Fiber High Temperature
http://www.isofrax.com
Insulation Information
http://www.fyrewrap.com
Official Fyrewrap Fire Prevention Products Information
1
11
|