Silastomer P40 RTV2
Page: 1/5
Version: 1.5 (AUS) Date of last alteration: 12.01.2006
NOT CLASSIFIED AS HAZARDOUS ACCORDING TO THE CRITERIA OF NOHSC
1 Identification of the substance/preparation and company
1.1 Name of substance/preparation
Commercial product name: Silastomer P40
1.2 Use of substance / preparation: Industrial.
Raw material for: mouldmaking.
1.3 Company name
Manufacturer: Dalchem Pty Ltd
Street/POB-No.: 141 Herald Street
State/postal code/city: Cheltenham 3192
Telephone: +61 3 9553 7040
Telefax: +61 3 9553 2407
1.4 Company name
Distributor: Dalchem Pty Ltd
Street/POB-No.: 141 Herald Street
State/postal code/city: Cheltenham Victoria 3192
Telephone: +61 3 9553 7040
Telefax: +61 3 9553 2407
1.5 Australian Emergency Telephone Number
Emergency Information Regulatory Compliance +61 3 9553 7040
Emergency Information (24 hours)鈥? +61 3 9553 7040
Dalchem Pty Ltd
2 Composition/information on ingredients
2.1 Chemical characterization (preparation):
Chemical characteristics
Polydimethylsiloxane with functional groups + auxiliaries for addition cross-linking
3 Hazards identification
3.0
This chemical is not classified as Hazardous according to the criteria of NOHSC.
This chemical is not classified as a Dangerous Good.
3.1 Classification:
R-Phrase Description
R- -
SILASTOMER P40
Version: 1.5 (AUS) Date of last alteration: 12.01.2006
4 First-aid measures
4.1 General information:
4.2 After inhalation:
No special measures required.
4.3 After contact with the skin:
Wipe off excess material with cloth or paper. Wash with plenty of water or water and soap.
4.4 After contact with the eyes:
Rinse immediately with plenty of water. Seek medical advice in case of continuous irritation.
4.5 After swallowing:
No special measures required. In cases of sickness seek medical advice (show label if possible).
5 Fire-fighting measures
5.1 Suitable extinguishing media:
water spray , extinguishing powder , alcohol-resistant foam , carbon dioxide , sand .
5.2 Extinguishing media which must not be used for safety reasons:
water jet .
5.3 Special exposure hazards arising from the substance or preparation itself, combustion products,
resulting gases:-
5.4 Special protective equipment for fire fighting:
Use respiratory protection independent of recirculated air.
6 Accidental release measures
6.1 Personal precautions:
No special measures required.
6.2 Environmental precautions:
Prevent material from entering sewers or surface waters.
6.3 Methods for cleaning up:
Take up mechanically and dispose of according to local/state/federal regulations. Clean any slippery
coating that remains using a detergent / soap solution or another biodegradable cleaner.
7 Handling and storage
7.0 General information:
Stir well before use.
7.1 Handling
Precautions for safe handling:
No special protective measures required.
Precautions against fire and explosion:
No special precautions against fire and explosion required.
7.2 Storage
Conditions for storage rooms and vessels:
none known
Advice for storage of incompatible materials:
not applicable
Further information for storage:
Keep container tightly closed.
Maximum temperature allowed during storage and transportation: 40 掳C
Material Safety Data Sheet Page: 3/5
SILASTOMER P40
Version: 1.5 (AUS) Date of last alteration: 12.01.2006
8 Exposure controls and personal protection equipment
8.1 Exposure limits
Maximum airborne concentrations at the workplace not applicable
8.2 Exposure limited and controlled
8.2.1 Exposure in the work place limited and controlled
General protection and hygiene measures:
Observe standard industrial hygiene practices for the handling of chemical substances. Do not eat
or drink when handling.
Personal protection equipment
Respiratory protection:
not required .
Hand protection:
not required .
Eye protection:
Recommendation: protective goggles .
8.2.2 Exposure to the environment limited and controlled:
-
9 Physical and chemical properties
9.1 General information
Physical state / form................: paste
Colour...............................: translucent
Odour................................: odourless
9.2 Important information about the protection of health, safety and the environment Method
(67/548/EEC):
Melting point / melting range........: not applicable
Boiling point / boiling range........: not applicable
Flash point..........................: approx. 307 掳C (DIN 51376)
Autoignition temperature.............: approx. 440 掳C (DIN 51794)
Lower explosion limit (LEL)..........: not applicable
Upper explosion limit (UEL)..........: not applicable
Density..............................: approx. 1,08 g/cm3 at 25 掳C, at 1013 hPa (DIN 51757)
Water solubility / miscibility.......: virtually insoluble
pH-Value.............................: not applicable
Viscosity (dynamic)..................: 50000 - 90000 mPa*s at 23 掳C (BROOKFIELD)
9.3 Other information
Thermal decomposition................: > 200 掳C
10 Stability and reactivity
10.0 General information:
If stored and handled in accordance with standard industrial practices no hazardous reactions are
known.
10.1 Conditions to avoid:
none known
10.2 Materials to avoid:
none known
10.3 Hazardous decomposition products:
If stored and handled in accordance with standard industrial practices and local regulations where
applicable: none known . Measurements have shown the formation of small amounts of formaldehyde at
temperatures above about 150 掳C (302 掳F) through oxidation.
Material Safety Data Sheet Page: 4/5
SILASTOMER P40
Version: 1.5 (AUS) Date of last alteration: 12.01.2006
11 Toxicological information
11.0 General information:
According to our present state of knowledge no damaging effect expected when treated in accordance
with standard industrial practices and local regulations where applicable.
11.1 Toxicological tests
Further information:
-
12 Ecological information
12.1 Ecotoxicity
No expected damaging effects to water organisms.
Effects in sewage treatment plants (bacteria toxicity: respiration-/reproduction inhibition):
According to current knowledge adverse effects on water purification plants are not expected.
12.2 Mobility
-
12.3 Persistence and degradability
Biodegradation / further information:
Biologically not degradable.
Further information:
-
12.4 Bio-accumulation potential
Further information:
Bioaccumulation is not expected to occur.
12.5 Other harmful effects
-
12.6 Further ecological information
General information:
In cross-linked state not soluble in water. Easily separable from water by filtration.
13 Disposal considerations
13.1 Material
Recommendation:
Dispose of according to regulations by incineration in a special waste incinerator. Small quantities
may be disposed of in a domestic waste incinerator. Observe local/state/federal regulations. After
solidification, material can be stored together with domestic waste. Observe local/state/federal
regulations.
13.2 Uncleaned packaging
Recommendation:
Completely discharge containers (no tear drops, no powder rest, scraped carefully). Containers may
be recycled or re-used. Observe local/state/federal regulations.
14 Transport information
14.1 Land transport GGVSE/ADR and RID
Road ADR:
Valuation....................: not Regulated
Railway RID:
Valuation....................: not Regulated
14.2 Inland navigation GGVBinsch/ADNR
14.3 Transport by sea GGVSee/IMDG-Code
Valuation....................: not Regulated
Marine Pollutant.............: no
14.4 Air transport ICAO-TI/IATA-DGR
Valuation....................: not Regulated
Material Safety Data Sheet Page: 5/5
SILASTOMER P40
Version: 1.5 (AUS) Date of last alteration: 12.01.2006
14.5 Transport/further information
Postal and courier service:
German postal dispatch.......: permitted
Informing dept. ref. to heading 14. Transport information:
Department MW-G
15 Regulatory information
15.1 Warning Label (EU)
R-Phrase Description
R- -
S-Phrase Description
S- -
15.2 National regulations:
SI 1999/3232: CHIP Regulations 1999
SI 1999/437: COSHH Regulations 1999
SI 1999/3242: Management of Health & Safety at Work Regulations 1999
Health & Safety at Work Act 1974
SI 1993/1643: Environmental Protection Act 1993 & Subsidiary Regulations.
Other national and local measures relating to the workplace, pollution control, environmental
protection and waste control.
16 Other information
16.1 Material
The above information describes exclusively the safety requirements of the product(s) and is based
on our present-day knowledge. It does not represent a guarantee for the properties of the product(s)
described in terms of the legal warranty regulations. Properties of the product are to be found in
the respective product leaflet.
16.2 Further information:
Commas appearing in numerical data denote a decimal point. Vertical lines in the left-hand margin
indicate changes compared with the previous version.
n.a. = not applicable n.s. = not subject to
Details of international registration status
Listed on the following inventories:
HSNO
IECSC
EINECS
TSCA
ECL
AICS
----- END OF MATERIAL SAFETY DATA SHEET -----
ALL Chemical Property And Toxicity Analysis PAGES IN THIS GROUP