Talstar PreTreat 庐
Termiticide
FIRST AID
For use by individuals/firms licensed or regis-
tered by the State to apply termiticide products. If swallowed 鈥? Immediately call a poison control center or doctor.
鈥? Do not induce vomiting unless told to do so by a
States may have more restrictive requirements
poison control center or doctor.
regarding qualifications of persons using this 鈥? Do not give any liquid to the person.
product. Consult the structural pest control reg- 鈥? Do not give anything by mouth to an unconscious
ulatory agency of your State prior to use of this person.
product.
If inhaled 鈥? Move person to fresh air.
EPA Reg. No. 279-3177 EPA Est. 279- 鈥? If person is not breathing, call 911 or an ambu-
lance, then give artificial respiration, preferably by
mouth-to-mouth, if possible.
By Wt.
Active Ingredient: 鈥? Call a poison control center or doctor for further
Bifenthrin*............................................................23.4% treatment advice
Other Ingredients** ..............................................76.6% If on skin or 鈥? Take off contaminated clothing.
clothing 鈥? Rinse skin immediately with plenty of water for 15-
100.0%
20 minutes.
*Cis isomers 97% minimum, trans isomers 3% maximum. 鈥? Call a poison control center or doctor for treatment
**Contains petroleum distillates. advice.
Talstar庐 PreTreat termiticide contains 2 pounds active ingredient per gal-
If in eyes 鈥? Hold eye open and rinse slowly and gently with
lon.
water for 15-20 minutes.
U.S. Patent No. 4,238,505 鈥? Remove contact lenses, if present, after the first 5
minutes, then continue rinsing eye.
鈥? Call a poison control center or doctor for treatment
advice.
HOTLINE NUMBER
KEEP OUT OF REACH OF CHILDREN
WARNING Have the product container or label with you when calling a poison
control center or doctor, or going for treatment. You may also con-
tact 1-(800)-331-3148 for Emergency Assistance.
See other panels for additional precautionary information. NOTE TO PHYSICIAN
Pesticide Hotline (800) 858-7378. This product is a pyrethroid. This
product also contains aromatic hydrocarbons. Because of the risk of
hydrocarbon pneumonitis if even tiny amounts are aspirated into the
lung during emesis, consideration should be given to gastric lavage
with endotracheal tube in place. Treatment is symptomatic and sup-
portive. Animal and vegetable fats, milk, cream and alcohol may
increase absorption and should not be administered.
For Information Regarding the Use of this Product Call 1-800-
321-1FMC (1362).
FMC Corporation
PRECAUTIONARY STATEMENTS
Agricultural Products Group
Hazards to Humans (and Domestic Animals)
Philadelphia PA 19103
Warning
May be fatal if swallowed. Causes skin irritation and moderate eye irri-
tation. Do not get on skin or on clothing. Avoid breathing vapors or spray
mist, and contact with eyes. Prolonged or frequently repeated skin con-
Net Contents tact may cause allergic reactions in some individuals. Wash thoroughly
with soap and water after handling and before eating, drinking or using
tobacco. Remove contaminated clothing and wash contaminated cloth-
ing before reuse.
8_05-C
Page 1
All pesticide handlers (mixers, loaders and applicators) must wear long- General Information on the Use of this Product
sleeved coveralls worn over a minimum of short-sleeved shirt and short
Not for use on plants being grown for sale or other commercial use, or
pants, socks, chemical-resistant footwear, chemical-resistant gloves and
for commercial seed production, or for research purposes.
protective eyewear. After the product is diluted in accordance with label
directions for use, shirts, pants, socks, shoes and waterproof gloves are The use of this product prevents and controls Termite infestations in and
sufficient. In addition, all pesticide handlers must wear a respiratory pro- around structures and constructions.
tection device1 when handling the concentrate or when working in a non-
The dilute insecticidal emulsion must be adequately dispersed in the soil
ventilated space. All pesticide handlers must wear protective eyewear-
to establish a barrier between the wood and the Termites in the soil. As
when working in a non-ventilated space or applying termiticide by rodding
a good practice: 1) all non-essential wood and cellulose containing
or sub-slab injection.
materials, should be removed from around foundation walls, crawl
NIOSH approved respirator with any R, P or HE filter.
1
spaces, and porches; 2) eliminate termite access to moisture by repair-
or a NIOSH approved respirator with an organic vapor (OV) cartridge ing faulty plumbing and/or construction grade. Soil around untreated
or canister with any R, P or HE prefilter. structural wood in contact with soil should be treated as described
below.
When treating adjacent to an existing structure, the applicator must check
the area to be treated, and immediately adjacent areas of the structure, To establish an effective insecticidal barrier with this product the service
for visible and accessible cracks and holes to prevent any leaks or signif- technician must be familiar with current Termite control practices such
icant exposures to persons occupying the structure. People present or as: trenching, rodding, sub-slab injection, coarse fan spraying of soil sur-
residing in the structure during application must be advised to remove faces, crack and crevice (void) injection, excavated soil treatment, and
their pets and themselves from the structure if they see any signs of leak- brush or spray applications to infested or susceptible wood. These tech-
age. After application, the applicator is required to check for leaks. All niques must be correctly employed to prevent or control infestations by
leaks resulting in the deposition of termiticide in locations other than those subterranean Termites such as: Coptotermes, Heterotermes, Reticuli-
prescribed on this label must be cleaned up prior to leaving the applica- termes and Zootermopsis. The biology and behavior of the species
tion site. Do not allow people or pets to contact contaminated areas or to involved should be considered by the service technician in determining
reoccupy contaminated areas of the structure until the clean-up is com- which control practices to use to eliminate or prevent the termite
pleted. infestation.
Environmental Hazards Choice of appropriate procedures should include consideration of such
variable factors as the design of the structure, location of heating, ven-
This pesticide is extremely toxic to fish and aquatic invertebrates. Do not
tilation, and air conditioning (HVAC) systems, water table, soil type, soil
apply directly to water, or to areas where surface water is present or to
compaction, grade conditions, and location and type of domestic water
intertidal areas below the mean high water mark. Do not contaminate
supplies and utilities.
water by cleaning of equipment or disposal of equipment washwaters. Do
not apply when weather conditions favor drift from treated areas. Care For advice concerning current control practices with relation to specific
should be used when spraying to avoid fish and reptile pets in/around local conditions, consult resources in structural pest control and state
ornamental ponds. cooperative extension and regulatory agencies.
Do not apply this product or allow it to drift to crops or weeds on which
Subterranean Termite Control
Bees are actively foraging. Additional information may be obtained from
your Cooperative Extension Service. Directions For Use
Important: Contamination of public and private water supplies must be
Physical/Chemical Hazards avoided by following these precautions: Use anti-backflow equipment or
Do not use or store near heat or open flame. procedures to prevent siphonage of insecticide into water supplies. Do
not contaminate cisterns or wells. Do not treat soil that is water saturat-
Do not apply this product in or on electrical equipment due to the possi-
ed or frozen or in any conditions where runoff or movement from the
bility of shock hazard.
treatment area (site) is likely to occur. Consult state and local specifica-
tions for recommended distances of wells from treated areas, or if such
DIRECTIONS FOR USE regulations do not exist, refer to Federal Housing Administration
It is a violation of Federal Law to use this product in a manner inconsis- Specifications (H.U.D.) for guidance.
tent with its labeling.
Note: Crawl spaces are to be considered inside of the structure.
Do not apply by air.
Critical Areas: Critical areas include areas where the foundation is pen-
Do not use in greenhouses, nurseries.
etrated by utility services, cracks and expansion joints, bath traps and
areas where cement constructions have been poured adjacent to the
foundation such as stairs, patios and slab additions.
STORAGE AND DISPOSAL
Structures with Wells/Cisterns Inside Foundations
Pesticide Storage
If crystals are observed, warm material to above 60掳F by plac- Structures that contain wells or cisterns within the foundation of a struc-
ing container in warm location. Shake or roll container periodi- ture can only be treated using the following techniques:
cally to redissolve solids. Do not use external source of heat for
1. Do not treat soil while it is beneath or within the foundation or along
warming container.
the exterior perimeter of a structure that contains a well or cistern. The
Keep out of reach of children and animals. Store in original con- treated backfill method must be used if soil is removed and treated
tainers only. Store in a cool, dry place and avoid excess heat. outside/away from the foundation. The treated backfill technique is
Carefully open containers. After partial use, replace lids and described as follows:
close tightly. Do not put concentrate or dilute material into food
a. Trench and remove soil to be treated onto heavy plastic sheeting
or drink containers. Do not contaminate other pesticides, fertiliz-
or similar material or into a wheelbarrow.
ers, water, food, or feed by storage or disposal.
b. Treat the soil at the rate of 4 gallons of dilute emulsion per 10 lin-
In case of spill, avoid contact, isolate area and keep out animals
ear feet per foot of depth of the trench, or 1 gallon per 1.0 cubic
and unprotected persons. Confine spills. Call FMC: (800) 331-
feet of soil. See 鈥淢ixing Directions section of the label. Mix thor-
3148.
oughly into the soil taking care to contain the liquid and prevent
To confine spill: If liquid, dike surrounding area or absorb with
runoff or spillage.
sand, cat litter, commercial clay or gel absorbent. If dry materi-
al, cover to prevent dispersal. Place damaged package in a c. After the treated soil has absorbed the diluted emulsion, replace
holding container. Identify contents. the soil into the trench.
Pesticide Disposal 2. Treat infested and/or damaged wood in place using an injection tech-
Pesticide wastes are toxic. Improper disposal of excess pesti- nique such as described in the 鈥淐ontrol of Wood Infesting Insects鈥?
cide, spray mixture, or rinsate is a violation of Federal Law. If section of this label.
these wastes cannot be disposed of by use according to label
Structures with Adjacent Wells/Cisterns and/or Other Water Bodies
instructions, contact your State Pesticide or Environmental
Applicators must inspect all structures with nearby water sources such
Control Agency, or the Hazardous Waste representative at the
as wells, cisterns, surface ponds, streams, and other bodies of water
nearest EPA Regional Office for guidance.
and evaluate, at a minimum, the treatment recommendations listed
Container Disposal
below prior to making an application
Metal or Plastic Container: Triple rinse (or equivalent) then offer
1. Prior to treatment, if feasible, expose the water pipe(s) coming from
for recycling or reconditioning, or puncture and dispose of in a
the well to the structure, if the pipe(s) enter the structure within 3 feet
sanitary landfill, or by other procedures approved by State and
of grade.
local authorities. Do not cut or weld metal containers.
Returnable/Refillable Containers: Do not rinse container. Do not 2. Prior to treatment, applicators are advised to take precautions to limit
empty remaining formulated product. Do not break seals. Return the risk of applying the termiticide into subsurface drains that could
intact to point of purchase. empty into any bodies of water. These precautions include evaluating
Page 2
whether application of the termiticide to the top of the footer may After Treatment: All holes in commonly occupied areas into which Talstar
PreTreat has been applied must be plugged. Plugs must be of a non-cel-
result in contamination of the subsurface drain. Factors such as depth
lulose material or covered by an impervious, non-cellulose material.
to the drain system and soil type and degree of compaction should be
taken into account in determining the depth of treatment.
Pre-Construction Subterranean Termite Treatment
3. When appropriate (i.e., on the water side of the structure), the treated
Pre-Construction Treatment: Do not apply at a lower dosage and/or
backfill technique (described above) can also be used to minimize off-
concentration than specified on this label for applications prior to
site movement of termiticide.
the installation of the finished grade.
Prior to using this technique near wells or cisterns, consult state, local or
When treating foundations deeper than 4 feet, apply the termiticide as the
federal agencies for information regarding approved treatment practices in
backfill is being replaced, or if the construction contractor fails to notify the
your area.
applicator to permit this, treat the foundation to a minimum depth of 4 feet
after the backfill has been installed. The applicator must trench and rod
Application Rate:
into the trench or trench along the foundation walls and around pillars and
Use a 0.06% emulsion for subterranean Termites.
other foundation elements, at the rate prescribed from grade to a mini-
Mixing Directions: Mix the termiticide use dilution in the following man- mum depth of 4 feet. When the top of the footing is exposed, the applica-
ner: Fill tank 1/4 to 1/3 full. Start pump to begin by-pass agitation and tor must treat the soil adjacent to the footing to a depth not to exceed the
place end of treating tool in tank to allow circulation through hose. Add bottom of the footing. However, in no case should a structure be treated
appropriate amount of Talstar庐 PreTreat termiticide. Add remaining below the footing.
amount of water. Let pump run and allow recirculation through the hose
Effective pre-construction subterranean Termite control is achieved by the
for 2 to 3 minutes.
establishment of vertical and/or horizontal insecticidal barriers using
0.06% emulsion of Talstar庐 PreTreat. To meet Termite proofing require-
Talstar PreTreat may also be mixed into full tanks of water, but requires
substantial agitation to insure uniformity of the emulsion. ments, follow the procedures in the latest edition of the Housing and
Urban Development Minimum Property Standards.
To prepare a 0.06% water emulsion, ready to use, dilute 1 quart of Talstar
Horizontal Barriers
PreTreat with 99.75 gallons of water.
Create a horizontal barrier wherever treated soil will be covered by a slab,
Mixing: such as footing trenches, slab floors, carports, and the soil beneath stairs
For the desired application rate, use the chart below to determine the and crawl spaces.
amount of Talstar庐 PreTreat Termiticide for a given volume of finished
To produce a horizontal insecticidal barrier, apply the emulsion at the rate
emulsion:
of 1 gallon per 10 square feet to fill soil. If fill is washed gravel or other
coarse material, apply at 1.5 gallons of emulsion per 10 square feet so
Amount of Talstar PreTreat
that the emulsion will reach the soil beneath the fill. Applications shall be
(Gallons except where noted)
made by a low pressure spray (less than 50 p.s.i.) using a coarse spray
Emulsion Amount Amount Desired Gallons nozzle. If slab will not be poured the same day as treatment, cover treat-
Concentration of Talstar of Water of Finished Emulsion ed soil with a water-proof barrier such as polyethylene sheeting. This is
not necessary if foundation walls have been installed around the treated
0.06% 0.32 oz 127.68 oz. 1
soil.
1.6 oz 4.99 5
3.2 oz. 9.975 10 Vertical Barriers
8 oz. 24.94 25
Vertical barriers should be established in areas such as around the base
0.5 qt. 49.875 50
of foundations, plumbing, utility entrances, back-filled soil against founda-
0.75 qt. 74.8125 75
tion walls and other critical areas.
1 qt 99.75 100
1.5 qt. 149.62 150 To produce a vertical barrier in soil, apply the emulsion at a rate of 4 gal-
2 qt. 199.5 200
lons per 10 linear feet per foot of depth. Distribute the treatment as even-
ly as possible.
0.12%* 0.64 oz 127.36 oz. 1
3.2 oz 4.975 5 a. When rodding or trenching, it is important that emulsion reaches the
6.4 oz. 9.95 10
top of the footing. Rod holes should be spaced to provide a continu-
0.5 qt. 24.875 25
ous insecticidal barrier.
1 qt. 49.75 50
1.5 qt. 74.625 75 b. Care should be taken to avoid soil wash-out around the footing.
2 qt 99.5 100
c. Trenches need not be wider than 6 inches. Emulsion should be
3 qt. 149.25 150
1 199 200 mixed with the soil as it is being replaced in the trench.
d. For a monolithic slab, an inside vertical barrier may not be required.
Common units of measure:
1 pint = 16 fluid ounces (oz.) Hollow block voids may be treated at a rate of 2 gallons of emulsion per
1 quart = 2 pints = 4 cups = 32 fluid ounces (oz.) 10 linear feet so that the emulsion will reach the top of the footing.
Prior to each application, applicators must notify the general contractor,
*For Termite applications, only use this rate in conjunction with the appli-
construction superintendent, or similar responsible party, of the intended
cation volume adjustments as listed in the section below or in the foam termiticide application and intended sites of application and instruct the
or underground service application sections. responsible person to notify construction workers and other individuals to
leave the area to be treated during application and until the termiticide is
Application Volume: To provide maximum control and protection against
absorbed into the soil.
termite infestation apply the specified volume of the finished water emul-
sion and active ingredient as set forth in the directions for use section of Foundations: For applications made after the final grade is installed, the
this label. If soil will not accept the labeled application volume, the volume applicator must trench and rod into the trench or trench along the founda-
may be reduced provided there is a corresponding increase in concentra- tion walls and around pillars and other foundation elements, at the rate
tion so that the amount of active ingredient applied to the soil remains the prescribed from grade to the top of the footing. When the footing is more
same. than four (4) feet below grade, the applicator must trench and rod into the
trench or trench along the foundation walls at the rate prescribed to a min-
Note: Large reductions of application volume reduce the ability to obtain a
imum depth of four feet. The actual depth of treatment will vary depend-
continuous barrier. Variance is allowed when volume and concentration
ing on soil type, degree of compaction, and location of termite activity.
are consistent with label directed rates and a continuous barrier can still
When the top of the footing is exposed, the applicator must treat the soil
be achieved.
adjacent to the footing to a depth not to exceed the bottom of the footing.
Where desirable for pre construction treatments, the volume of the 0.12% However, in no case should a structure be treated below the footing.
emulsion may be reduced by 1/2 the labeled volume. See Volume
Attention
Adjustment Chart below.
Do not apply to pets, crops, or sources of electricity.
Note: When volume is reduced, the hole spacing for subslab injection and
Firewood is not to be treated.
soil rodding may require similar adjustment to account for lower volume
Use only in well ventilated areas.
dispersal of the termiticide in the soil.
During any application to overhead areas of structure, cover surfaces
below with plastic sheeting or similar material.
Volume Adjustment Chart
Do not allow spray to contact food, foodstuffs, food contacting surfaces,
Rate (% emulsion) 0.06% 0.12% food utensils or water supplies.
Volume allowed Thoroughly wash dishes and food handling utensils with soap and water
if they become contaminated by application of this product.
Horizontal (gallons 0.5
emulsion/10 ft2) Do not treat areas where food is exposed.
1.0 gallons gallons
Vertical (gallons 2.0 During indoor surface applications do not allow dripping or run-off to
occur.
emulsion/10 lin. ft.) 4.0 gallons gallons
Do not apply this pesticide in livestock buildings (barns).
Do not apply a broadcast application to interior surfaces of homes.
Page 3
Keep children and pets off treated areas following application until the
spray has dried.
Conditions of Sale and Limitation of Warranty and Liability:
NOTICE: Read the entire Directions for Use and Conditions of Sale
and Limitation of Warranty and Liability before buying or using this
product. If the terms are not acceptable, return the product at once,
unopened, and the purchase price will be refunded.
The Directions for Use of this product should be followed carefully. It is
impossible to eliminate all risks inherently associated with the use of
this product. Crop injury, ineffectiveness, or other unintended conse-
quences may result because of such factors as manner of use or appli-
cation, weather or crop conditions beyond the control or FMC or Seller.
All such risks shall be assumed by Buyer and User, and Buyer and
User agree to hold FMC and Seller harmless for any claims relating to
such factors.
Seller warrants that this product conforms to the chemical
description on the label and is reasonably fit for the purposes stat-
ed on the Directions for Use when used in accordance with the
directions under normal conditions of use. FMC MAKES NO WAR-
RANTIES OF MERCHANTABILITY OR OF FITNESS FOR A PARTIC-
ULAR PURPOSE, NOR ANY OTHER EXPRESS OR IMPLIED WAR-
RANTIES WITH RESPECT TO THE SELECTION, PURCHASE, OR
USE OF THIS PRODUCT. Any warranties, express or implied, hav-
ing been made are inapplicable if this product has been used con-
trary to label instructions, or under abnormal conditions, or under
conditions not reasonably foreseeable to (or beyond the control
of) seller or FMC, and buyer assumes the risk of any such use.
To the extent permitted by law, FMC or seller shall not be liable for any
incidental, consequential or special damages resulting from the use or
handling of this product. THE EXCLUSIVE REMEDY OF THE USER
OR BUYER, AND THE EXCLUSIVE LIABILITY OF FMC AND SELLER
FOR ANY AND ALL CLAIMS, LOSSES, INJURIES OR DAMAGES
(INCLUDING CLAIMS BASED ON BREACH OF WARRANTY, CON-
TRACT, NEGLIGENCE, TORT, STRICT LIABILITY OR OTHERWISE)
RESULTING FROM THE USE OR HANDLING OF THIS PRODUCT,
SHALL BE THE RETURN OF THE PURCHASE PRICE OF THE
PRODUCT OR, AT THE ELECTION OF FMC OR SELLER, THE
REPLACEMENT OF THE PRODUCT.
This Conditions of Sale and Limitation of Warranty and Liability may not
be amended by any oral or written agreement.
Talstar and FMC鈥擳rademarks of FMC Corporation (03/01/04)
U.S. Patent No. 6,251,415 (SFR chemical technology).
Page 4
|