**** SECTION 2 - COMPOSITION, INFORMATION ON INGREDIENTS ****
+----------------+--------------------------------------+----------+-----------+
| CAS# | Chemical Name | % | EINECS# |
|----------------|--------------------------------------|----------|-----------|
| 10025-91-9 |Antimony trichloride | >99 | 233-047-2 |
+----------------+--------------------------------------+----------+-----------+
Hazard Symbols: C N
Risk Phrases: 34 51/53
**** SECTION 3 - HAZARDS IDENTIFICATION ****
EMERGENCY OVERVIEW
Causes burns. Toxic to aquatic organisms, may cause long-term
adverse effects in the aquatic environment.Corrosive.Moisture
sensitive.Hygroscopic (absorbs moisture from the air).
Potential Health Effects
Eye:
Causes eye burns.
Skin:
Causes skin burns.
Ingestion:
Causes gastrointestinal tract burns. May be harmful if swallowed.
Inhalation:
Causes chemical burns to the respiratory tract. May cause lung
damage. May produce cardiovascular effects.
Chronic:
Chronic exposure may cause liver damage.
**** SECTION 4 - FIRST AID MEASURES ****
Eyes:
In case of contact, immediately flush eyes with plenty of water for
at least 15 minutes. Get medical aid immediately.
Skin:
In case of contact, immediately flush skin with plenty of water for
at least 15 minutes while removing contaminated clothing and shoes.
Get medical aid immediately. Wash clothing before reuse.
Ingestion:
If swallowed, do NOT induce vomiting. Get medical aid immediately.
If victim is fully conscious, give a cupful of water. Never give
anything by mouth to an unconscious person.
Inhalation:
If inhaled, remove to fresh air. If not breathing, give artificial
respiration. If breathing is difficult, give oxygen. Get medical aid.
Notes to Physician:
**** SECTION 5 - FIRE FIGHTING MEASURES ****
General Information:
As in any fire, wear a self-contained breathing apparatus in
pressure-demand, MSHA/NIOSH (approved or equivalent), and full
protective gear. During a fire, irritating and highly toxic gases
may be generated by thermal decomposition or combustion. May react
with metals and lead to the formation of flammable hydrogen gas.
Substance may react with water, and may release corrosive and/or
toxic gases.
Extinguishing Media:
Do NOT get water inside containers. For large fires, use water
spray, fog or alcohol-resistant foam. Do NOT use straight streams of
water. For small fires, use carbon dioxide, dry chemical, dry sand,
or alcohol-resistant foam. Most foams will react with the material
and release corrosive/toxic gases. Cool containers with flooding
quantities of water until well after fire is out.
**** SECTION 6 - ACCIDENTAL RELEASE MEASURES ****
General Information: Use proper personal protective equipment as indicated
in Section 8.
Spills/Leaks:
Vacuum or sweep up material and place into a suitable disposal
container. Avoid generating dusty conditions. Provide ventilation. Do
not get water inside containers. A vapor suppressing foam may be used
to reduce vapors.
**** SECTION 7 - HANDLING and STORAGE ****
Handling:
Wash thoroughly after handling. Remove contaminated clothing and
wash before reuse. Use with adequate ventilation. Minimize dust
generation and accumulation. Do not get in eyes, on skin, or on
clothing. Do not ingest or inhale.
Storage:
Store in a cool, dry, well-ventilated area away from incompatible
substances. Keep away from water. Keep away from metals. Corrosives
area. Keep containers tightly closed.
**** SECTION 8 - EXPOSURE CONTROLS, PERSONAL PROTECTION ****
Engineering Controls:
Local exhaust ventilation may be necessary to control any air
contaminants to within their TLVs during the use of this product.
Facilities storing or utilizing this material should be equipped
with an eyewash facility and a safety shower.
Exposure Limits
CAS# 10025-91-9:
United Kingdom, WEL - TWA: (listed as antimony compounds): 0.5 mg
TWA (except stibine, as Sb)
United Kingdom, WEL - STEL: (listed as antimony compounds): 1.5 m
STEL (except stibine, as Sb)
United States OSHA: 0.5 mg/m3 TWA (listed under Antimony).0.5 mg
TWA (as Sb) (listed under Antimony compounds).
Belgium - TWA: (listed as antimony compounds): 0.5 mg/m3 VLE (as
France - VME: (listed as antimony compounds): 0.5 mg/m3 VME (as S
Germany: (listed as antimony compounds): 0.5 mg/m3 VME (as Sb)
Japan: (listed as antimony compounds): 0.1 mg/m3 OEL (except stib
as Sb)
Malaysia: (listed as antimony compounds): 0.5 mg/m3 TWA (as Sb)
Netherlands: (listed as antimony compounds): 0.5 mg/m3 MAC (as Sb
Russia: 0.3 mg/m3 TWA
Russia: (listed as antimony): 0.2 mg/m3 STEL
Spain: (listed as antimony compounds): 0.5 mg/m3 VLA-ED (except
antimony hydride, as Sb)
Personal Protective Equipment
Eyes:
Wear appropriate protective eyeglasses or chemical
safety goggles as described by OSHA's eye and face
protection regulations in 29 CFR 1910.133 or European
Standard EN166.
Skin:
Wear appropriate protective gloves to prevent skin
exposure.
Clothing:
Wear appropriate protective clothing to prevent skin
exposure.
Respirators:
Follow the OSHA respirator regulations found in 29
CFR 1910.134 or European Standard EN 149. Use a
NIOSH/MSHA or European Standard EN 149 approved
respirator if exposure limits are exceeded or if
irritation or other symptoms are experienced.
**** SECTION 9 - PHYSICAL AND CHEMICAL PROPERTIES ****
Physical State: Solid
Color: white
Odor: pungent odor
pH: Not available.
Vapor Pressure: 1 mm Hg @ 49.2C
Viscosity: Not available.
Boiling Point: 223 deg C
Freezing/Melting Point: 73 deg C
Autoignition Temperature: Not available.
Flash Point: Not applicable.
Explosion Limits, lower: Not available.
Explosion Limits, upper: Not available.
Decomposition Temperature: Not available.
Solubility in water: soluble (but hydrolysis to SbOCl)
Specific Gravity/Density: 3.14
Molecular Formula: SbCl3
Molecular Weight: 228.11
**** SECTION 10 - STABILITY AND REACTIVITY ****
Chemical Stability:
Stable at room temperature in closed containers under normal storage
and handling conditions.
Conditions to Avoid:
Dust generation, exposure to moist air or water.
Incompatibilities with Other Materials:
Imcompatible with aluminum, potassium and sodium, perchloric acid.
Hazardous Decomposition Products:
Hydrogen chloride, chlorine, irritating and toxic fumes and gases,
antimony/antimony oxides.
Hazardous Polymerization: Has not been reported.
**** SECTION 11 - TOXICOLOGICAL INFORMATION ****
RTECS#:
CAS# 10025-91-9: CC4900000
LD50/LC50:
CAS# 10025-91-9: Oral, rat: LD50 = 525 mg/kg.
Inhalation TCLo (human): 73 mg/m3.
Carcinogenicity:
Antimony trichloride -
Not listed by ACGIH, IARC, or NTP.
Other:
See actual entry in RTECS for complete information.
**** SECTION 12 - ECOLOGICAL INFORMATION ****
**** SECTION 13 - DISPOSAL CONSIDERATIONS ****
Products which are considered hazardous for supply are classified as Special
Waste and the disposal of such chemicals is covered by regulations which may
vary according to location. Contact a specialist disposal company or the local
waste regulator for advice. Empty containers must be decontaminated before
returning for recycling.
**** SECTION 14 - TRANSPORT INFORMATION ****
IATA
Shipping Name: ANTIMONY TRICHLORIDE
Hazard Class: 8
UN Number: 1733
Packing Group: II
IMO
Shipping Name: ANTIMONY TRICHLORIDE
Hazard Class: 8
UN Number: 1733
Packing Group: II
RID/ADR
Shipping Name: ANTIMONY TRICHLORIDE
Hazard Class: 8
UN Number: 1733
Packing group: II
USA RQ: CAS# 10025-91-9: 1000 lb final RQ; 454 kg final RQ
**** SECTION 15 - REGULATORY INFORMATION ****
European/International Regulations
European Labeling in Accordance with EC Directives
Hazard Symbols: C N
Risk Phrases:
R 34 Causes burns.
R 51/53 Toxic to aquatic organisms, may cause
long-term adverse effects in the aquatic environment.
Safety Phrases:
S 26 In case of contact with eyes, rinse immediately
with plenty of water and seek medical advice.
S 45 In case of accident or if you feel unwell, seek
medical advice immediately (show the label where
possible).
S 61 Avoid release to the environment. Refer to
special instructions/safety data sheets.
WGK (Water Danger/Protection)
CAS# 10025-91-9: 2
Canada
CAS# 10025-91-9 is listed on Canada's DSL List.
CAS# 10025-91-9 is listed on Canada's Ingredient Disclosure List.
US FEDERAL
TSCA
CAS# 10025-91-9 is listed on the TSCA inventory.
**** SECTION 16 - ADDITIONAL INFORMATION ****
MSDS Creation Date: 3/11/1999 Revision #5 Date: 6/01/2005
The information above is believed to be accurate and represents the best
information currently available to us. However, we make no warranty of
merchantability or any other warranty, express or implied, with respect to
such information, and we assume no liability resulting from its use. Users
should make their own investigations to determine the suitability of the
information for their particular purposes. In no way shall the company be
liable for any claims, losses, or damages of any third party or for lost
profits or any special, indirect, incidental, consequential or exemplary
damages, howsoever arising, even if the company has been advised of
the possibility of such damages.
--------------------------------------------------------------------------------
--------------------------------------------------------------------------------
|
|
|
| ALL MSDS PAGES IN THIS GROUP
| | NAME | CAS |
|
6-Amino-2-Naphthoic Acid, 90%
| 11668-47-4 |
|
Zirconium (IV) Oxide, P.A.
| 1314-23-4 |
|
cis-Dichlorodiamineplatinum(II), 99.99%
| 15663-27-1 |
|
1-Bromonaphthalene 96%, contains max. 2% 2-bromonaphthalene
| 90-11-9 |
|
1-Heptanesulfonic acid, sodium salt, monohydrate, HPLC grade
| 207300-90-1 |
|
1-Hexanesulfonic acid sodium salt, HPLC grade
| 2832-45-3 |
|
5-Bromo-1-pentene, 96%
| 1119-51-3 |
|
2,6-Diphenylphenol
| 2432-11-3 |
|
L-Cystine
| 56-89-3 |
|
1-Pentanesulfonic Acid, Sodium Salt Monohydrate, HPLC Grade
| 22767-49-3 |
|
1,1,2-Trichloroethane Density Standard
| 79-00-5 |
|
2-Ethoxyethanol, 99%
| 110-80-5 |
|
Antimony Trichloride
| 10025-91-9 |
|
2-Ethoxyethyl acetate 99%
| 111-15-9 |
|
DL-2-Octanol, 97%
| 123-96-6 |
|
2,2,2-Trifluoroethanol
| 75-89-8 |
|
5-Amino-2-methylindole, 98%
| 7570-49-2 |
|
Bromoacetaldehyde Diethyl Acetal, 97%
| 2032-35-1 |
|
2-Acetylcyclohexanone, 97%
| 874-23-7 |
|
Lauric acid, 98%
| 143-07-7 |
|
4-Methoxy-2-nitroaniline, 98%
| 96-96-8 |
|
1-Nitroso-2-naphthol-3,6-disulfonic acid disodium salt
| 0-00-0 |
|
Toluidine Blue O Zinc Chloride Double Salt
| 0-01-1 |
|
2,4,6-Triphenylpyrylium Chloride, 90%
| 40836-01-9 |
|
2-Isopropoxyethanol, 98%
| 109-59-1 |
|
2,6-Difluorobenzoyl Isocyanate
| 60731-73-9 |
|
1-(4-Chlorophenyl)-1-Cyclopropane- Carboxylic Acid, 99%
| 72934-37-3 |
|
1-Bromo-1-propene, mixture of isomers, 95%
| 590-14-7 |
|
3-Aminopyrrolidine Dihydrochloride
| 103831-11-4 |
|
2,2,4-Trimethylpentane, p.a.
| 540-84-1 |
|
Phenyl Salicylate, 99% (UV-Vis)
| 118-55-8 |
|
MOPS
| 1132-61-2 |
|
P-Naphtholbenzein, 90+% (UV-VIS)
| 145-50-6 |
|
1-Amino-4-Hydroxyanthraquinone, 96%
| 116-85-8 |
|
4-Aminoantipyrine, 98%
| 83-07-8 |
|
Sodium metatungstate, 2.82 density solution in water, stabilized
| 7732-18-5 |
|
8-Hydroxyquinoline, p.a.
| 148-24-3 |
|
3-Methyl-2-Cyclohexen-1-One, 98%
| 1193-18-6 |
|
Cerium(IV) sulfate tetrahydrate
| 10294-42-5 |
|
Sodium metatungstate hydrate, crystalline
| 12141-67-2 |
|
O-Methylbenzyl Cyanide, 98%
| 22364-68-7 |
|
l(-)-Glutathione, oxidized, hydrate, 95%
| 27025-41-8 |
|
Antimony Trioxide
| 1309-64-4 |
|
Dibutyl L-Tartrate
| 87-92-3 |
|
(-)-Terpinen-4-ol, 97%
| 562-74-3 |
|
3,5-Dinitrosalicylic Acid Monosodium Salt, Monohydrate, 97% (Titr.)
| 46506-88-1 |
|
4-Tert.-Butyl-Calix[4]arene-Crown-4-Complex
| 171058-95-0 |
|
4-Tert.-Butyl-Calix[4]Arene-Crown-5-Complex
| 99314-01-9 |
|
4-Tert.-Butyl-Calix[4]Arene-Crown-6-Complex
| 129518-51-0 |
|
2,3,4,5-Tetrafluoro-6-nitrobenzoic acid
| 16583-08-7 |
|
|