LEXMARK INTERNATIONAL, INC. -- MAGENTA TONER CARTRIDGE, 12A1451
=======================================================
Material Safety Data Sheet
=======================================================
MSDS Num: CLPQT
MSDS NAME: MAGENTA TONER CARTRIDGE, 12A1451
Responsible Party
Name: LEXMARK INTERNATIONAL, INC.
Address: 740 NEW CIRCLE RD. NW
City: LEXINGTON KY 40550-1876
Info Phone: 606-232-3000/606-232-3333
Emergency Phone Number: 606-232-3333
Review Ind: Y
Published: Y
=======================================================
Contractor Summary
=======================================================
Name: LEXMARK INTL INC
Address: 740 WEST NEW CIRCLE RD
City: LEXINGTON KY 40550-1876
Phone: 859-232-3000/859-232-3333
=======================================================
Ingredients
=======================================================
Name: POLYESTER RESIN - 1. (TRADE SECRET OR PATENTED MOLECULE, NJTSN
80100252-5001P)
% low Wt: 75.
% high Wt: 85.
OSHA PEL: NOT ESTABLISHED.
ACGIH TLV: NOT ESTABLISHED.
-----------------------------
Name: POLYESTER RESIN - 2. (MANUFACTURER-PROVIDED INVALID CAS# 39282-25-7)
% low Wt: 5.
% high Wt: 10.
OSHA PEL: NOT ESTABLISHED.
ACGIH TLV: NOT ESTABLISHED.
-----------------------------
Cas: 114803-11-1
Name: CHARGE CONTROL AGENT.
% low Wt: .5
% high Wt: 1.5
OSHA PEL: NOT ESTABLISHED.
ACGIH TLV: NOT ESTABLISHED.
-----------------------------
Cas: 5281-04-9
Name: ORGANIC PIGMENT
% low Wt: 3.
% high Wt: 4.
OSHA PEL: NOT ESTABLISHED.
ACGIH TLV: NOT ESTABLISHED.
------------------------------
Cas: 9010-79-1
Name: POLYPROPYLENE WAX
% low Wt: 2.
% high Wt: 3.
OSHA PEL: NOT ESTABLISHED.
ACGIH TLV: NOT ESTABLISHED.
------------------------------
Cas: 7631-86-9
Name: AMORPHOUS SILICA
% low Wt: 1.
% high Wt: 1.5
Other REC Limits: ACGIH 3 MG/M3 RESP
OSHA PEL: 80 MG/M3/%SI*O2 CALC
ACGIH TLV: 10 MG/M3 (INHALABLE
------------------------------
Cas: 68909-20-6
Name: SILICA (SILANAMINE)
% low Wt: .2
% high Wt: .4
OSHA PEL: NOT ESTABLISHED.
ACGIH TLV: NOT ESTABLISHED.
=======================================================
Health Hazards Data
=======================================================
Route Of Entry Inds - Inhalation: YES
Skin: YES
Ingestion: NO
Carcinogenicity Inds - NTP: NO
IARC: NO
OSHA: NO
Effects of Exposure: POTENTIAL HEALTH EFFECTS: INHALATION - SHORT TERM
EXPOSURE: TESTING AND/OR INFORMATION ON THIS OR SIMILAR TONERS, OR ON THE
CONSTITUENTS OF THIS TONER INDICATE LOW INHALATION TOXICITY. AS WITH EXPOSUR
E TO HIGH CONCENTRATIONS OF ANY DUST, MINIMAL RESPIRATORY TRACT IRRITATION
MAY OCCUR IF EXCESSIVE AMOUNTS OF TONER DUSTS ARE INHALED. LONG TERM
EXPOSURE: NO ADVERSE CHRONIC EFFECTS KNOWN AT INTENDED L EVEL OF USE.
EXPOSURE NOT PROBABLE WITH INTENDED USE. SKIN CONTACT - SHORT TERM EXPOSURE:
TESTING AND/OR INFORMATION ON THIS OR SIMILAR TONERS, OR THE CONSTITUENTS OF
THIS TONER INDICATE THIS TONER I S (SIGNS AND SYMPTOMS OF OVEREXPOSURE)
Signs And Symptions Of Overexposure: HEALTH HAZARDS ACUTE AND CHRONIC (CONT):
NOT A SKIN IRRITANT AND IS OF LOW DERMAL TOXICITY. LONG TERM EXPOSURE: RARE
INDIVIDUALS MAY NOTE SKIN RASH WITH REPEATED CONTACT. EXPOSURE NOT PROBABLE
WITH INTENDED USE. EYE CONTACT - SHORT TERM EXPOSURE: TONER MAY ACT AS A
MECHANICAL IRRITANT. LONG TERM EXPOSURE: NO ADVERSE CHRONIC EFFECTS KNOWN.
EXPOSURE NOT PROBABLE WITH INTENDED USE. INGESTION - SH ORT TERM EXPOSURE:
TESTING AND/OR INFORMATION ON THIS OR SIMILAR TONERS, OR ON THE CONSTITUENTS
OF THIS TONER INDICATE LOW ORAL TOXICITY. EXPOSURE NOT PROBABLE WITH INTENDED
USE. LONG TERM EXPOSURE: N O (SUPPLEMENTAL SAFETY AND HEALTH)
Medical Cond Aggravated By Exposure: NONE KNOWN AT INTENDED LEVELS OF USE.
EXPOSURE TO HIGH AIRBORNE DUST CONCENTRATIONS, INCLUDING TONER, MAY AGGRAVATE
EXISTING RESPIRATORY CONDITIONS.
First Aid: INHALATION: IF SYMPTOMS, SUCH AS SHORTNESS OF BREATH OR PERSISTENT
COUGHING ARE EXPERIENCED, REMOVE SOURCE OF CONTAMINATION AND MOVE INDIVIDUAL
TO FRESH AIR. IF SYMPTOMS PERSIST, SEEK MEDICAL ATTENTIO N. SKIN CONTACT:
WASH AFFECTED AREA WITH SOAP AND WATER. SHOULD IRRITATION OCCUR, SEEK MEDICAL
ATTENTION. EYE CONTACT: DO NOT RUB EYES. FLUSH IMMEDIATELY WITH PLENTY OF
WATER. REMOVE CONTACT LENSES AND CONTINUE FLUSHING FOR AT LEAST 15 MINUTES.
SEEK MEDICAL ATTENTION IF IRRITATION DEVELOPS AND PERSISTS. INGESTION: IF
CONSCIOUS, IMMEDIATELY WASH MOUTH OUT WITH PLENTY OF WATER. SEEK MEDICAL
ATTEN TION.
=======================================================
Handling and Disposal
=======================================================
Spill Release Procedures: OCCUPATIONAL SPILL: IF A DUST CLOUD IS POSSIBLE DUE
TO A SPILL, REMOVE ALL SOURCES OF IGNITION SUCH AS OPEN SPARKS, FLAMES OR
STATIC DISCHARGE TO PREVENT IGNITION OF THE DUST. MINIMIZE DUST GENERATION
DURING CLEAN UP. SWEEP UP SPILL WITH NON-METALLIC BROOM AND DUST PAN. TO
AVOID POSSIBLE DUST EXPLOSION, DO NOT USE VACUUM CLEANERS TO CLEAN UP SPILLS.
CONTAIN FOR DISPOSAL. OIL (OTHER INFORMATION)
Waste Disposal Methods: THIS PRODUCT IS NOT A LISTED OR HAZARDOUS WASTE IN
ACCORDANCE WITH FEDERAL REGULATION 40 CFR PART 261 OR CODE OF CALIFORNIA
REGULATIONS TITLE 22. IF DISCARDED IN ITS PURCHASED FORM, THIS PRODUCT WOULD
NOT BE A HAZARDOUS WASTE BY EITHER LISTING OR BY CHARACTERISTIC. HOWEVER,
UNDER RCRA, IT IS THE RES PONSIBILITY OF PRODUCT USER TO (TRANSPORT INFO)
Handling And Storage Precautions: STORE IN A COOL DRY PLACE. STORE AWAY FROM
OXIDIZING MATERIALS. WHEN HANDLING, MINIMIZE GENERATION OF DUST. SUPPLY
ADEQUATE VENTILATION.
Other Precautions: PHYSICAL HAZARDS: AS WITH MOST FINELY DIVIDED DUSTS,
EXPLOSION IS POSSIBLE WHEN EXTREMELY HIGH CONCENTRATIONS OF DUST AND AN
IGNITION SOURCE ARE PRESENT. NOT A HAZARD UNDER NORMAL CONDITIONS OF USE.
=======================================================
Fire and Explosion Hazard Information
=======================================================
Autoignition Temp Text: N/AV.
Extinguishing Media: CO2, WATER SPRAY OR FOG, DRY CHEMICAL, OR FOAM.
Fire Fighting Procedures: NIOSH APPROVED SELF CONTAINED BREATHING APPARATUS MAY
BE REQUIRED IF A LARGE NUMBER OF CARTRIDGES IS INVOLVED.
=======================================================
Control Measures
=======================================================
Respiratory Protection: NONE REQUIRED FOR INTENDED USE IN PRINTER. IF
REQUIRED, USE A NIOSH APPROVED RESPIRATOR APPROPRIATE FOR THE EXPOSURE OF
CONCERN (FP N).
Ventilation: MECHANICAL ROOM VENTILATION.
Protective Gloves: NONE REQUIRED FOR INTENDED USE IN PRINTER. IMPERVIOUS
GLOVES (FP N).
Eye Protection: NONE REQUIRED FOR INTENDED USE IN PRINTER. ANSI APPROVED SAFETY
GLASSES (FP N).
Other Protective Equipment: EYEWASH MEETING ANSI DESIGN CRITERIA (FP N).
PROTECTIVE CLOTHING: NONE REQUIRED FOR INTENDED USE IN PRINTER.
Supplemental Safety and Health: SIGNS AND SYMPTOMS OF OVEREXPOSURE (CONT):
ADVERSE CHRONIC EFFECTS KNOWN. EXPOSURE NOT PROBABLE WITH INTENDED USE.
SIGNS AND SYMPTOMS OF EXPOSURE: TONER ON SKIN OR MUCOUS MEMBRANES (MOUTH,
NOSE).
=======================================================
Physical/Chemical Properties
=======================================================
Vapor Pres: NOT AVAILABLE.
Spec Gravity: 1.16 @ 20C.
Solubility in Water: NEGLIGIBLE.
Appearance and Odor: MAGENTA ODORLESS POWDER
Percent Volatiles by Volume: NOT AVAIL.
=======================================================
Reactivity Data
=======================================================
Stability Indicator: YES
Stability Condition To Avoid: COMBUSTIBLE ATMOSPHERES OF TONER DUST. IGNITION
SOURCES, EXCESSIVE HEAT, SPARKS AND OPEN FLAME.
Materials To Avoid: STRONG OXIDIZERS.
Hazardous Decomposition Products: CARBON DIOXIDE, CARBON MONOXIDE, AND PHENOL
DERIVATIVES AT TEMPERATURES >300C.
Hazardous Polymerization Indicator: NO
Conditions To Avoid Polymerization: THIS PRODUCT WILL NOT POLYMERIZE.
=======================================================
Toxicological Information
=======================================================
Toxicological Information: ACUTE TOXICITY: NOT EXPECTED TO BE ACUTELY TOXIC.
CHRONIC TOXICITY: NOT EXPECTED TO BE TOXIC. EXPOSURE LIMITS:
OSHA: 15 MG/M3 (TOTAL DUST, PARTICULATES NOT OTHERWISE REGULATED-PNOR), 5 MG/M3
(RE SPIRABLE DUST, PARTICULATES NOT OTHERWISE REGULATED-PNOR), 80
MG/M3/%SI*O2 (TOTAL DUST, MEASURED AS AMORPHOUS SILICA). ACGIH: 10 MG/M3
(TOTAL DUST, PARTICULATES NOT OTHERWISE CLASSIFIED-PNOC), 3 MG/M 3
(RESPIRABLE DUST, PARTICULATES NOT OTHERWISE CLASSIFIED-PNOC), 10 MG/M3
(INHALABLE PARTICULATE, MEASURED AS AMORPHOUS SILICA), 3 MG/M3 (RESPIRABLE
PARTICULATE, MEASURED AS AMORPHOUS SILICA).
=======================================================
Ecological Information
=======================================================
Ecological: ENVIRONMENTAL IMPACT RATING (0-4): NOT AVAILABLE. ACUTE AQUATIC
TOXICITY: NOT AVAILABLE. DEGRADABILITY: NOT AVAILABLE. LOG BIOCONCENTRATION
FACTOR (BCF): NOT AVAILABLE. LOG OCTANOL / WATER PARTITI ON COEFFICIENT: NOT
AVAILABLE.
=======================================================
MSDS Transport Information
=======================================================
Transport Information: THIS PRODUCT IS NOT REGULATED AS A HAZARDOUS MATERIAL BY
THE DOT. WASTE DISPOSAL METHOD (CONT): DETERMINE ATE THE TIME OF
DISPOSAL WHETHER A METERIAL HAS BEEN CONTAMINATED AND SHOULD BE CLASSIF IED
AS A HAZARDOUS WASTE. DISPOSAL IS SUBJECT TO LOCAL, STATE AND FEDERAL
REGULATIONS.
=======================================================
Regulatory Information
=======================================================
Sara Title III Information: NONE OF THE PRODUCT INGREDIENTS ARE LISTED AS
EMERGENCY PLANNING AND COMMUNITY RIGHT-TO-KNOW ACT (EPCRA) - SECTION 302:
EXTREMELY HAZARDOUS SUBSTANCES (ERS). NONE OF THE PRODUCT COMPONENTS ARE
PRESEN T ABOVE THE MINIMUM QUANTITES OF LISTED CHEMICALS IN EPCRA SECTION 313
SUPPLIER NOTIFICATION.
Federal Regulatory Information: ALL INGREDIENTS ARE REGISTERED UNDER THE TOXIC
SUBSTANCES CONTROL ACT (TSCA) OR UNDER POLYMER EXEMPTION. ALL INGREDIENTS
ARE EXEMPT, REGISTERED OR CONSIDERED REGISTERED (POLYMERS) UNDER THE EUROPEAN
INVENTORY OF EXISTING COMMERCIAL CHEMICAL SUBSTANCES (EINECS).
State Regulatory Information: CALIFORNIA PROPOSITION 65: THIS PRODUCT CONTAINS
NO KNOWN MATERIALS AT LEVELS WHICH THE STATE OF CALIFORNIA HAS FOUND TO CAUSE
CANCER, BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM.
=======================================================
Other Information
=======================================================
Other Information: CHEMICAL FAMILY: CARTRIDGE CONTAINS TONER. PRODUCT USE:
OPTRA COLOR 1200 PRINTERS. LEXMARK HAS DETERMINED THAT MATERIAL SAFETY
DATA SHEETS ARE NOT REQUIRED FOR PRINT CARTRIDGES. FOR CUSTOMER CO NVENIENCE,
LEXMARK PROVIDES PRODUCT INFORMATION IN THIS FAMILIAR FORMAT.
(PHYSICAL/CHEMICAL CONT) PRESSURIZED: NO. PARTICLE SIZE: D50 8.5UM. SOFTENING
POINT: 117-123C. SPILL RELEASE PROCEDURE S (CONT): PERMEATED SWEEPING
COMPOUND MAY ASSIST IN CLEAN UP OF TONER SPILLED ON NONPOROUS SURFACES.
=======================================================
HAZCOM Label
=======================================================
MSDS NAME: MAGENTA TONER CARTRIDGE, 12A1451
Company: LEXMARK INTL INC
Street: 740 WEST NEW CIRCLE RD
City: LEXINGTON KY
Zipcode: 40550-1876
Health Emergency Phone: 606-232-3333
Label Required IND: Y
Date Of Label Review: 11/01/2001
Status Code: A
Origination Code: F
Chronic Hazard IND: Y
Eye Protection IND: YES
Skin Protection IND: YES
Signal Word: CAUTION
Respiratory Protection IND: YES
Health Hazard: Slight
Contact Hazard: Slight
Fire Hazard: Slight
Reactivity Hazard: None
Hazard And Precautions: ACUTE: LOW INHALATION TOXICITY. EXPOSURE TO HIGH
CONCENTRATIONS OF ANY DUST MAY CAUSE MINIMAL RESPIRATORY TRACT IRRITATION.
NOT A SKIN IRRITANT, HAS LOW DERMAL TOXICITY. DUST MAY ACT AS A MECHANICAL E
YE IRRITANT. HAS LOW ORAL TOXICITY. CHRONIC: RARE INDIVIDUALS MAY NOTE SKIN
RASH UPON REPEATED OR PROLONGED CONTACT.
=======================================================
Disclaimer (provided with this information by the compiling agencies): This
information is formulated for use by elements of the Department of Defense.
The United States of America in no manner whatsoever expressly or implied
warrants, states, or intends said information to have any application, use or
viability by or to any person or persons outside the Department of Defense
nor any person or persons contracting with any instrumentality of the United
States of America and disclaims all liability for such use. Any person
utilizing this instruction who is not a military or civilian employee of the
United States of America should seek competent professional advice to verify
and assume responsibility for the suitability of this information to their
particular situation regardless of similarity to a corresponding Department
of Defense or other government situation.
*** END OF RECORD *** |
|
|
| ALL PAGES On Chemical Property IN THIS GROUP
| | NAME | CAS |
|
800, HAI-800 ALLOY
| 7440-47-3
7439-89-6
7440-02-0 |
|
750, HAI-X750 ALLOY
| 7440-47-3
7439-89-6
7440-02-0 |
|
601, HAI-601 ALLOY
| 7440-47-3
7439-89-6
7440-02-0 |
|
600, HAI-600 ALLOY
| 7440-47-3
7439-89-6
7440-02-0 |
|
BEST TEST PAPER CEMENT, (SEE SUPPLEMENTAL)
| 142-82-5
9006-04-6 |
|
541, HAI-WELD NICR 80 ALLOY
| 7440-47-3
7439-89-6
7440-02-0
7440-21-3 |
|
528, HAI-NICR 40 ALLOY
| 7440-47-3
7439-89-6
7440-02-0
7440-21-3 |
|
527, HAI-NICR 35 ALLOY
| 7440-47-3
7439-89-6
7440-02-0
7440-21-3 |
|
525, HAI-NICR 35B ALLOY
| 7440-47-3
7439-89-6
7440-02-0
7440-21-3 |
|
520, HAI-NICR 35CB ALLOY
| 7440-47-3
7439-89-6
7440-02-0
7440-21-3 |
|
506, HAI-WELD 506 ALLOY
| 7440-47-3
7439-89-6
7440-02-0
7440-21-3 |
|
441, HAI-5676 ALLOY
| 7440-47-3
7440-02-0 |
|
026, HAI-HPX ALLOY
| 7440-47-3
7440-02-0
7440-21-3 |
|
021, HAI-XPX ALLOY
| 7440-47-3
7440-02-0 |
|
057, HAI-NICR 350X ALLOY
| 7440-47-3
7439-89-6
7439-96-5
7440-02-0 |
|
066, HAI-66 ALLOY
| 7440-47-3
7439-89-6
7440-02-0 |
|
111, HAI-KPOX ALLOY
| 7440-47-3
7440-02-0 |
|
007, HAI-NICR 60 ALLOY
| 7440-47-3
7439-89-6
7440-02-0
7440-21-3 |
|
542, HAI-NICR 80LA ALLOY
| 7440-47-3
7439-96-5
7440-02-0 |
|
722, HAI-WELD 62 ALLOY
| 7440-47-3
7439-89-6
7440-02-0 |
|
302, HAI-302SS ALLOY
| 7440-47-3
7439-89-6
7439-96-5
7440-02-0
7440-21-3 |
|
250, HAI-NICR 80F ALLOY
| 7440-47-3
7439-96-5
7440-02-0 |
|
431, HAI-431 ALLOY
| 7440-47-3
7440-02-0
7440-21-3 |
|
305, HAI-305SS ALLOY
| 7440-47-3
7439-89-6
7440-02-0 |
|
309, HAI-309SS ALLOY
| 7440-47-3
7439-89-6
7439-96-5
7440-02-0
7440-21-3 |
|
304, HAI-304SS ALLOY
| 7440-47-3
7439-89-6
7440-02-0 |
|
248, HAI-NICR 80AA ALLOY
| 7440-47-3
7439-89-6
7440-02-0
7440-21-3 |
|
246, HAI-NICR 70 ALLOY
| 7440-47-3
7439-89-6
7440-02-0
7440-21-3 |
|
347, HAI-347SS ALLOY
| 7440-47-3
7439-89-6
7439-96-5
7440-02-0
7440-21-3 |
|
316, HAI-316SS ALLOY
| 7440-47-3
7440-02-0 |
|
332, HAI-332CBSS ALLOY
| 7440-47-3
7439-89-6
7439-96-5
7440-02-0
7440-21-3 |
|
330, HAI-330SS ALLOY
| 7440-47-3
7439-89-6
7439-96-5
7440-02-0
7440-21-3 |
|
310, HAI-310SS ALLOY
| 7440-47-3
7439-89-6
7439-96-5
7440-02-0 |
|
314, HAI-314SS ALLOY
| 7440-47-3
7439-89-6
7439-96-5
7440-02-0
7440-21-3 |
|
120, HAI-KPTP ALLOY
| 7440-47-3
7440-02-0 |
|
121, HAI-KP ALLOY
| 7440-47-3
7440-02-0 |
|
123, HAI-EP ALLOY
| 7440-47-3
7440-02-0 |
|
126, HAI-NP ALLOY
| 7440-47-3
7440-02-0
7440-21-3 |
|
241, HAI-NICR 80 ALLOY
| 7440-47-3
7440-02-0
7440-21-3 |
|
242, HAI-NICR 80CB ALLOY
| 7440-47-3
7440-02-0
7440-21-3 |
|
245, HAI-NICR 80AL ALLOY
| 7440-47-3
7440-02-0
7440-21-3 |
|
PHILLYCLAD 1775/620TS HARDENER, 3461H
| |
|
INTERNAL STANDARD MIXTURE, STM-341N
| 67-56-1
3114-55-4
3855-82-1
540-36-3
363-72-4 |
|
MAGENTA TONER CARTRIDGE, 12A1451
| 114803-11-1
5281-04-9
9010-79-1
7631-86-9
68909-20-6 |
|
SPRAY BOND (TM) ADHESIVE 6111 GREEN
| 29160-13-2
9003-07-0 |
|
SCOTCH-WELD DP-110 B/A PART B GRAY EPOXY ADHESIVE
| |
|
60/40 ROSIN CORE WIRE SOLDER
| |
|
CLEAR RTV SILICONE ADHESIVE SEALANT
| 63148-62-9
112945-52-5
17689-77-9
4253-34-3
64-19-7 |
|
MILPRF85285C(MILC85285B) TYPE I, 03W127ACAT17925
| 3779-63-3
822-06-0
64742-95-6
123-86-4
107-87-9
763-69-9
1119-40-0
627-93-0
106-65-0 |
|
METREGRIP 303 ACTIVATOR
| |
|
|