===================== Product Identification =====================
MSDS NAME:PRIMER COATING, EPOXY 724116
NIIN:00-082-1714
Kit Part:Y
MSDS Number: BCXXN
=== Responsible Party ===
Company:PRATT & LAMBERT, INC.-INDUSTRIAL COATINGS DIV.
Address:16116 E 13TH ST
Box:2153
City:WICHITA
State:KS
ZIP:67201
Country:US
CAGE:FO127
=== Contractor Identification ===
Company:PRATT & LAMBERT, INC/BUFFALO, NY 14240
Box:22
CAGE:FO127
Company:PRATT AND LAMBERT INC
Address:Box:6027
City:CLEVELAND
State:OH
ZIP:44101-1027
Country:US
Phone:216-566-2902
CAGE:61196
============= Composition/Information on Ingredients =============
Name:PROPYLENE GLYCOL MONOMETHYL ETHER
CAS:107-98-2
RTECS #:UB7700000
OSHA PEL:100 PPM/150 STEL
ACGIH TLV:100 PPM/150STEL;9192
Name:XYLENES (O-,M-,P- ISOMERS) (SARA III)
CAS:1330-20-7
RTECS #:ZE2100000
OSHA PEL:100 PPM/150 STEL
ACGIH TLV:100 PPM/150STEL;9192
EPA Rpt Qty:1000 LBS
DOT Rpt Qty:1000 LBS
Name:N-BUTYL ALCOHOL (SARA III)
CAS:71-36-3
RTECS #:EO1400000
OSHA PEL:100 PPM
ACGIH TLV:S, C 50 PPM; 9293
EPA Rpt Qty:5000 LBS
DOT Rpt Qty:5000 LBS
===================== Hazards Identification =====================
Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Health Hazards Acute and Chronic:REPORTS HAVE ASSOCIATE PROLONGED AND
REPEATED OCCUPATIONAL OVEREXPOSURE TO SOLVENTS WITH PERMANENT BRAIN
AND NERVOUS SYSTEM DAMAGE. OVEREXPOSURE TO XYLENE MAY CAUSE INJURY
TO THE LIVER, KIDNEYS AND BL OOD. REPEATED CONTACT MAY CAUSE
DERMATITIS.
Effects of Overexposure:SWALLOW-GASTROINTESTINAL IRRITATION, NAUSEA AND
VOMITING. ASPIRATION OF MATERIAL INTO THE LUNGS CAN CAUSE CHEMICAL
PNEUMONITIS WHICH CAN BE FATAL. INHALE-MAY CAUSE NOSE OR THROAT
IRRITATION. EYE-MAY C AUSE SEVERE EYE IRRITATION. SKIN-MAY CAUSE
DEFATTING AND IRRITATION OF THE SKIN. MAY CAUSE SKIN SENSITIZATION.
======================= First Aid Measures =======================
First Aid:IF SWALLOWED, CALL POISON CONTROL CENTER, HOSPITAL EMERGENCY
ROOM OR MD IMMED. INHALED, REMOVE TO FRESH AIR IMMED. IF BREATHING
HAS STOPPED, GIVE ARTIFICIAL RESPIRATION. KEEP WARM AND QUIET. GET
MED A TTN IMMED. EYE, FLUSH WITH LARGE AMTS OF WATER AT LEAST 15
MIN. GET MED ATTN IMMED. SKIN, WASH AFFECTED AREA WITH SOAP &
WATER. REMOVE CONTAMINATED CLOTHING. GET MED ATTN IF IRRITATION
PERSISTS.
===================== Fire Fighting Measures =====================
Flash Point:80F-27C
Extinguishing Media:NFPA CLASS B FIRE EXTINGUISHER DESIGNED TO
EXTINGUISH FLAMMABLE LIQUID FIRES. POLYMER FOAM PREFERRED FOR LARGE
FIRES.
Fire Fighting Procedures:WEAR SELF-CONTAINED BREATHING APPARATUS. WATER
MAY BE INEFFECTIVE, BUT MAY BE USED TO PREVENT PRESSURE BUILD-UP.
IF WATER IS USED, FOG NOZZLES ARE PREFERABLE.
Unusual Fire/Explosion Hazard:DURING EMERGENCY CONDITIONS, OVEREXPOSURE
TO DECOMPOSITION PRODUCTS MAY CAUSE A HEALTH HAZARD. OBTAIN MEDICAL
ATTENTION.
================== Accidental Release Measures ==================
Spill Release Procedures:KEEP SPECTATORS AWAY. ELIM ALL IGNITION
SOURCES. DIKE & CONTN SPILL WITH INERT MATL. TR LQDS TO COV MTL
CNTNR FOR RECOV OR DISP OR REM W/INERT ABSORB.USE NON-SPRKG
TOOLS.PLACE ABSORB MAT IN COV METAL CONTNR FOR DISP. PREVENT
CONTAM OF SEW,STRMS,ETC
====================== Handling and Storage ======================
Handling and Storage Precautions:DO NOT STORE ABOVE 90 DEGREES F.
Other Precautions:DO NOT TAKE INTERNALLY.CLOSE CONTAINER AFTER EACH
USE.KEEP AWAY FROM CHILDREN. AVOID SKIN CONTACT.EMPTY CONTAINERS
MUST NOT BE WASH & REUSED FOR ANY PURPOSE. NEVER USE PRESSURE TO
EMPTY. DO NOT WELD, BRAZE OR CUT ON EMPTY CONTAINER.
============= Exposure Controls/Personal Protection =============
Respiratory Protection:WELL-VENTILATED AREA-NIOSH APPROVED MECHANICAL
FILTER RESPIRATOR TO REMOVE OVERSPRAY.RESTRICTED AREA-NIOSH
APPROVED PAINT SPRAY RESPIRATOR TO REMOVE SPRAY MIST AND ORGANIC
VAPORS.CONFINED AREA-NIOSH A PPROVED AIR-SUPPLIED RESPIRATOR.
Ventilation:PROVIDE GENERAL DILUTION & LOCAL EXHAUST VENTILATION IN
SUFFICIENT VOL & PATTERN TO MAINTAIN BELOW LOWEST EXPOS LIMITS.
Protective Gloves:SOLVENT IMPERMEABLE GLOVES
Eye Protection:WEAR SAFETY SPECTACLES
Other Protective Equipment:EYEWASH FACILITY, SAFETY SHOWER
Supplemental Safety and Health
SOLVENT IMPERMEABLE GLOVES REQUIRED FOR REPEATED PROLONGED CONTACT PART
B OF TWO PART PRODUCT SEE P/N FOR PART A KEY1:F4
================== Physical/Chemical Properties ==================
HCC:F3
Boiling Pt:B.P. Text:243F-293F
Vapor Pres:11
Vapor Density:>AIR
Evaporation Rate & Reference:SLOWER THAN ETHER
Percent Volatiles by Volume:81
================= Stability and Reactivity Data =================
Stability Indicator/Materials to Avoid:YES
STRONG ACIDS OR ALKALINE MATERIALS. OXIDIZING MATERIALS.ACCELERATORS.
Stability Condition to Avoid:AVOID EXCESSIVE HEAT AND SOURCES OF
IGNITION. ALSO, THE ADDITION OF EXCESS HARDENER.
Hazardous Decomposition Products:BURNING, INCLUDING WHEN HEATED BY
WELDING OR CUTTING, WILL PRODUCE SMOKE, CARBON MONOXIDE AND CARBON
DIOXIDE.
Conditions to Avoid Polymerization:KEEP AWAY FROM HEAT, SPARKS AND
FLAME.
==================== Disposal Considerations ====================
Waste Disposal Methods:IAW FED, STATE & LOCAL LAWS. INCINERATE ONLY IN
EPA PERMITTED FACILITY. DO NOT INCINERATE CLOSED CONTAINERS.
OBSERVE PRECAUTIONS FOR DISPOSAL OF FLAMMABLE MATERIALS.
CONTAMINATED ABSORBANT MAY BE DISP OSED IN A HAZARDOUS WASTE
LANDFILL.
Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.
*** END OF RECORD *** |
|
|
| ALL PAGES On Chemical Property IN THIS GROUP
| | NAME | CAS |
|
8030-00-081-2329 GR E,COLOR CODE PURPLE
| |
|
TB 1363D(CV)
| |
|
TB 1361D(C)
| |
|
GRADE B,YELLOW
| |
|
STA-LOK 800
| 79-41-4 |
|
TB 1363A(AV)
| |
|
TB 1363A(AV)
| |
|
TB 1361(A),RED,GRADE A
| |
|
GRADE A,RED
| |
|
GRADE AA,GREEN
| |
|
TB 1361B(AA)
| |
|
COBALT NITRATE
| 10141-05-6 |
|
CATALYST 11
| 106-50-3
872-50-4 |
|
CATALYST 9
| 112-57-2
112-24-3
4067-16-7 |
|
RTV-60, SILICONE RUBBER
| 78-10-4 |
|
P150F
| 1336-36-3 |
|
P6X9V3
| |
|
1041249
| 7440-48-4 |
|
MA-356E
| 7440-48-4 |
|
16962-5
| 1310-58-3 |
|
E90 R P3 EPOXY PRIMER-PART A
| 1330-20-7
110-80-5
7439-92-1
18540-29-9
67-56-1 |
|
V93 V P1 EPOXY PRIMER-PART B
| 110-80-5
108-10-1
1330-20-7 |
|
PRIMER COATING, EPOXY 724600
| 1330-20-7
1317-36-8
14808-60-7
1333-82-0
14807-96-6
112945-52-5
71-36-3
123-86-4 |
|
PRIMER COATING, EPOXY 724116
| 107-98-2
1330-20-7
71-36-3 |
|
CHARTERSOL 210-66
| |
|
VIBRA-CLEAN
| |
|
WATERLESS HAND CLEANER PASTE
| 7732-18-5 |
|
TRAFFIC BEADS, GLASS BEADS
| |
|
728-002
| 67-63-0 |
|
METAL PRETREATMENT,RESIN-ACID,MIL-C-8514C
| 13530-65-9
71-36-3
64-17-5
7664-38-2 |
|
PRIMER,PRETREATMENT COATING*
| 13530-65-9
64-17-5
7664-38-2 |
|
MIL-C-22750C EPOXY POLYAMIDE
| |
|
MIL C-22750C EPOXY POLYAMIDE
| |
|
1-1X-88 26081 GRAY MIL-C-22750C
| |
|
1-1X-45 #16081 GRAY
| |
|
1-1X-48 16473 GRAY MIL-C-22750C
| |
|
1-1X-32 #16081 GRAY
| |
|
PT-426/PT-428
| 71-36-3 |
|
EPOXY COATING, WHITE 17925 COMP I M1-036
| 78-93-3
107-98-2
123-86-4
1330-20-7
108-88-3 |
|
POLYAMID, COMP II UO-082
| 67-63-0
78-93-3 |
|
MIL-C-22750 EPOXY WHITE PART A
| 108-88-3
110-43-0 |
|
COATING, EPOXY, WHITE
| 108-88-3 |
|
EPOXY COATING, WHITE 17925 COMP I M1-036
| 108-88-3
108-65-6
78-93-3 |
|
POLYAMID, COMP II UO-082
| 78-93-3
67-63-0 |
|
MIL-C-22750 EPOXY(WHITE PART A
| 108-88-3 |
|
724-102 724-112
| 108-88-3
71-36-3
67-63-0
78-93-3
110-80-5 |
|
PRIMER COATING
| 7789-06-2
25068-38-6
108-88-3 |
|
02Y024,BASE,PART A,EPOXY.
| 78-93-3
123-86-4
7789-06-2
7758-97-6
108-88-3 |
|
02Y024,CATALYST,POLYAMIDE,PART B
| 123-86-4
71-36-3
67-63-0
108-88-3
78-93-3 |
|
EPOXY PRIMER CAT.MIL-P-23377D
| 1330-20-7 |
|
|