===================== Product Identification =====================
MSDS NAME:ENAMEL, ALKYD, GLOSS, LO VOC CT, WHITE 17875, ID 774720
NIIN:00-515-1596
MSDS Number: CBTNN
=== Responsible Party ===
Company:PRATT AND LAMBERT INC
Address:16116 E 13TH ST
Box:2153
City:WICHITA
State:KS
ZIP:67201
Country:US
Info Phone Num:316-733-1361
Emergency Phone Num:716-873-6000 DOT EMER 8002553924
Preparer's Name:W A ELLISON
CAGE:61196
=== Contractor Identification ===
Company:PRATT AND LAMBERT INC
Box:6027
City:CLEVELAND
State:OH
ZIP:44101-1027
Country:US
Phone:216-566-2902
CAGE:61196
============= Composition/Information on Ingredients =============
Name:N-BUTYL ACETATE (SOLVENT) (VAPOR PRESSURE 10 MM HG @ 20C)
(LFL 1.7; UFL 7.6)
CAS:123-86-4
RTECS #:AF7350000
Fraction by Wt: 5.0%
Other REC Limits:NONE RECOMMENDED
OSHA PEL:150 PPM;STEL 200 PPM
ACGIH TLV:150 PPM;STEL 200 PPM
EPA Rpt Qty:5000 LBS
DOT Rpt Qty:5000 LBS
Name:SOLVENT NAPHTHA, LIGHT AROMATIC (SOLVENT)
CAS:64742-95-6
Fraction by Wt: 5.0%
Other REC Limits:NONE RECOMMENDED
Name:XYLENE (SOLVENT) (SARA III) (VAPOR PRESSURE 5 MM HG @ 20C)
(LFL 1.0; UFL 7.0)
CAS:1330-20-7
RTECS #:ZE2100000
Fraction by Wt: 15.0%
Other REC Limits:NONE RECOMMENDED
OSHA PEL:100 PPM;STEL 150 PPM
ACGIH TLV:100 PPM;STEL 150 PPM
EPA Rpt Qty:1000 LBS
DOT Rpt Qty:1000 LBS
Name:TITANIUM DIOXIDE (PIGMENT)
CAS:13463-67-7
RTECS #:XR2275000
Fraction by Wt: 25.0%
Other REC Limits:NONE RECOMMENDED
OSHA PEL:10 MG/M3
ACGIH TLV:10 MG/M3
Name:SILICA, AMORPHOUS HYDRATED (PIGMENT)
CAS:112945-52-5
RTECS #:VV7310000
Fraction by Wt: <5.0%
Other REC Limits:NONE RECOMMENDED
OSHA PEL:6 MG/M3
ACGIH TLV:10 MG/M3
Name:ETHYL BENZENE (SARA 313)(VAPOR PRESSURE = 1.0 MMHG @ 20C)
CAS:100-41-4
RTECS #:DA0700000
Fraction by Wt: 5.0%
Other REC Limits:NONE RECOMMENDED
OSHA PEL:25 PPM; 125 MG/M3
ACGIH TLV:25 PPM; 125 MG/M3
EPA Rpt Qty:1000 LBS
DOT Rpt Qty:1000 LBS
Name:VOC: 3.12 LB/GAL LESS WATER & NEGLIGIBLY PHOTOCHEMICALLY
REACTIVE MATERIALS; 374 G/L LESS WATER; CALCULATED
RTECS #:9999999VO
Fraction by Wt: NA
Other REC Limits:NONE RECOMMENDED
===================== Hazards Identification =====================
Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:INGESTION: GASTROINTESTINAL
IRRITATION, NAUSEA, VOMITING. ASPIRATION INTO LUNG MAY CAUSE CHEM
PNEUMONITIS (CAN BE FATAL). INHALATION: NOSE OR THROAT IRRITATION.
ACUTE CENTRAL NERVOUS SYSTEM DEPRESSION (HEADACHES, DIZZINESS,
NAUSEA, CONFUSION). EYE: SEVERE IRRITATION & CORNEAL DAMAGE. SKIN:
DEFATTING & IRRITATION.
Effects of Overexposure:CHRONIC: LIVER, KIDNEY AND BLOOD INJURY.
PROLONGED & REPEATED OVEREXPOSURE ASSOCIATED WITH PERMANENT BRAIN &
NERVOUS SYSTEM DAMAGE. INTENTIONAL MISUSE BY DELIBERATELY
CONCENTRATING & INHALING PRODUCT MAY BE HARMFUL OR FATAL.
======================= First Aid Measures =======================
First Aid:INGEST: DONT INDUCE VOMITING. CALL POISON CTR/EMERG ROOM/DR
IMMED. INHAL:REMOVE TO FRESH AIR IMMED. IF BREATHING STOPPED, GIVE
ARTIF RESPRTN. KEEP WARM & QUIET. GET MED AID IMMED. EYE: FLUSH
W/WATER 1 5 MIN, LIFTING EYELIDS. GET MED AID. SKIN: REMOVE CONTAM
CLOTHES. WASH AFFECTED AREA W/SOAP & WATER. GET MED AID IF IRRIT
PERSISTS. NOTE TO DR: DIRECT TREATMENT @ CLINICAL CONDITION &
SYMPTOM CONTROL.
===================== Fire Fighting Measures =====================
Flash Point:59.0F,15.0C
Lower Limits:1.0
Upper Limits:7.6
Extinguishing Media:NFPA CLASS B EXTINGUISHERS (CO2, DRY CHEMICAL,
ALCOHOL FOAM) FOR FLAMMABLE LIQ. POLYMER FOAM PREFERRED FOR LARGE
FIRES.
Fire Fighting Procedures:WATER MAY BE INEFFECTIVE, USE TO COOL EXPOSED
CONTAINERS (FOG NOZZLES PREFERRED) TO PREVENT PRESSURE BUILDUP,
AUTOIGNITION OR EXPLOSION WHEN EXPOSED TO HEAT.
Unusual Fire/Explosion Hazard:DURING EMERGENCY CONDITIONS, OVEREXPOSURE
TO DECOMPOSITION PRODUCTS MAY BE HEALTH HAZARD. SYMPTOMS MAY NOT BE
IMMEDIATELY APPARENT. GET MEDICAL AID. FLAMMABLE.
================== Accidental Release Measures ==================
Spill Release Procedures:WEAR RSPRTR,EYE,HAND,BODY PROTECTN. KEEP
SPECTATORS AWAY. ELIMINATE IGNIT SOURCES. DIKE & CONTAIN W/INERT
MAT'L (SAND/EARTH/ETC). TRANSFER LIQ/USED ABSORBENT TO COVERED
METAL CONTAINER. USE NON-SPARKI NG TOOL. PREVENT SEWER, GROUNDWATER
CONTAMINATION.
====================== Handling and Storage ======================
Handling and Storage Precautions:DO NOT STORE ABOVE 115 F. STORE LARGE
QUANTITIES IN COMPLIANCE WITH OSHA 29 CFR 1910.106. DO NOT TAKE
INTERNALLY. DO NOT BREATHE SANDING DUST.
Other Precautions:CLOSE CONTAINER AFTER EACH USE. DO NOT WASH & REUSE
EMPTY CONTAINER FOR ANY PURPOSE. GROUND & BOND CONTAINERS TO
RECEIVING CONTAINER. DO NOT WELD, BRAZE, OR CUT ON EMPTY CONTAINER.
NEVER USE PRESSURE TO EMPTY. DRUM IS NOT A PRESSURE VESSEL.
============= Exposure Controls/Personal Protection =============
Respiratory Protection:IF VENTD,MAY NOT REQ RSPRTR.IN RESTRICTD VENT,
NIOSH CHEM CARTRIDGE RSPRTR MAY BE REQ'D.SPRAYNG,MECHAN PREFILTER
MAY ALSO BE REQ'D.CONFIND AREAS,USE AIR SUPPLD RSPRTR.SEE OSHA
29CFR1910.134"RESP PROTE CT"&"RESP PROTECT-MANUAL & GUIDELINE"AIH
Ventilation:LOCAL EXHAUST VENT TO KEEP BELOW TLV. REMOVE DECOMPOSITION
PRODUCT. SEE "INDUST VENT-MANUAL RECOMMENDED PRACTICES" ACGIH
Protective Gloves:IMPERMEABLE GLOVES (NORTH-SILVER SHIELD)
Eye Protection:WEAR SAFETY SPECTACLES.
Other Protective Equipment:EYEWASH FACILITY, SAFETY SHOWER.
Supplemental Safety and Health
NK
================== Physical/Chemical Properties ==================
HCC:F2
Boiling Pt:B.P. Text:252 TO 335F
Melt/Freeze Pt:M.P/F.P Text:-50F,-46C
Decomp Temp:Decomp Text:1832F,1000C
Vapor Pres:10 @ 68F
Vapor Density:> AIR
Spec Gravity:1.3
pH:4-7
Evaporation Rate & Reference:SLOWER THAN DIETHYL ETHER
Solubility in Water:SLIGHT IN WATER
Appearance and Odor:LIQUID, SOLVENT ODOR
Percent Volatiles by Volume:42.0
================= Stability and Reactivity Data =================
Stability Indicator/Materials to Avoid:YES
STRONG ACIDS OR ALKALINE MATERIALS. OXIDIZING MATERIALS.
Stability Condition to Avoid:AVOID EXCESSIVE HEAT (>115F) AND SOURCES
OF IGNITION.
Hazardous Decomposition Products:BURNING, INCLUDING WHEN HEATED BY
WELDING OR CUTTING, WILL PRODUCE SMOKE, CARBON MONOXIDE & CARBON
DIOXIDE.
==================== Disposal Considerations ====================
Waste Disposal Methods:DISPOSE IN ACCORDANCE WITH FEDERAL, STATE, &
LOCAL LAWS OR REGULATIONS. THIS PRODUCT, IF DISCARDED DIRECTLY,
WOULD BE CLASSIFIED A HAZARDOUS WASTE BASED ON ITS IGNITABILITY
CHARACTERISTIC (FLASH POINT 140F OR LESS). PROPER RCRA
CLASSIFICATION: D001.
Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.
*** END OF RECORD *** |
|