Search    ENTER KEYWORD
MSDS Material Safety Data Sheet
CAS

1310-73-2
7681-52-9

File Name: cleantec_com_au---Gel_Stain_Remover_msds.asp
     MATERIAL SAFETY DATA SHEET
1. IDENTIFICATION OF THE MATERIAL AND SUPPLIER

PRODUCT NAME: GEL STAIN REMOVER
OTHER NAMES: PACER GEL STAIN REMOVER
RECOMMENDED USE: Foam sanitiser / detergent for cleaning.
SUPPLIER NAME: CAMPBELL CLEANTEC (ABN 92 009 657 489)
ADDRESS: 32 PERIVALE STREET, DARRA, QLD, 4076
TELEPHONE: GENERAL + 61 7 3710 3200
ENQUIRIES:
CUSTOMER SERVICE: 1800 077 240
FAX: GENERAL + 61 7 3710 3210
ENQUIRIES:
CUSTOMER SERVICE: + 61 7 3710 3207
EMERGENCY TELEPHONE NUMBER: AUSTRALIA: 1800 628 724 (ALL HOURS)
INTERNATIONAL: + 61 7 3710 3184 (ALL HOURS)
2. HAZARDS IDENTIFICATION
HAZARD CLASSIFICATION: Classified as hazardous according to the criteria of NOHSC.
Not classified as a dangerous good according to the criteria of ADG Code (see section 14).
Classified as schedule 5 according to the criteria of SUSDP (see section 15).
HAZARD CATEGORY: Xi - Irritant
RISK PHRASES: R36 鈥? Irritating to eyes.
R38 鈥? Irritating to skin.
R31 鈥? Contact with acids liberates toxic gas.
SAFETY PHRASES: S1/2 鈥? Keep locked up and out of reach of children.
S24/25 鈥? Avoid contact with eyes and skin.
S26 鈥? In case of contact with eyes, rinse immediately with plenty of water and seek medical
advice.
S37/39 鈥? Wear suitable protective clothing and gloves.
S45 鈥? In case of accident or if you feel unwell, seek medical advice immediately (show the label
whenever possible).
S50 鈥? Do not mix with acids.
The information contained in this MSDS is specific to the product when handled and used neat. This product when diluted may not require the
same control measures as the neat product. Check with your technical representative if in doubt.

3. COMPOSITION / INFORMATION ON INGREDIENTS

INGREDIENT CAS No. PROPORTION (% w/w)
The ingredients below are considered either hazardous, dangerous goods or poison scheduled according to the criteria of NOHSC, ADG
Code and SUSDP (respectively) at the levels used in the product.

sodium hydroxide 1310-73-2 <10%
sodium hypochlorite 7681-52-9 <10%
The ingredients below are not considered either hazardous, dangerous goods or poison scheduled according to the criteria of NOHSC,
ADG Code and SUSDP (respectively) at the levels used in the product.

builder <10%
alkaline salts <10%
anionic surfactant <10%
surfactants <10%
hydrotrope <10%
perfume <10%
water 30 鈥? 60%

Product Name: Page:
GEL STAIN REMOVER 1 of 5
MATERIAL SAFETY DATA SHEET

4. FIRST AID MEASURES
For advice, contact a Poisons Information Centre (Phone Australia 131126, New Zealand
INGESTION:
0800 764 766) or a doctor. If swallowed, do NOT induce vomiting.
If in eyes, hold eyelids apart and flush the eye continuously with running water. Continue flushing
EYE CONTACT:
until advised to stop by the Poisons Information Centre or a doctor, or for at least 15 minutes.
If skin or hair contact occurs, remove contaminated clothing and flush skin and hair with running
SKIN CONTACT:
water. Continue flushing until advised to stop by the Poisons Information Centre or a doctor.
Remove from source of exposure to fresh air. Seek medical assistance if the effects persist.
INHALATION:
** SHOW THIS SAFETY DATA SHEET TO A DOCTOR **
Potable water should be available to rinse eyes or skin. Provide eye baths and safety showers.
FIRST AID FACILITIES:
Treat symptomatically and as for strongly alkaline corrosive material.
NOTES TO PHYSICIAN:

5. FIRE FIGHTING METHODS

Water spray, foam, carbon dioxide or dry chemical powder.
SUITABLE EXTINGUISHING MEDIA:
The product is non-combustible; however, the packaging material may burn to emit
HAZARDS FROM COMBUSTION:
noxious fumes. Contact with metals may liberate hydrogen gas which is extremely
flammable.
Fire fighters should wear self-contained breathing apparatus to minimise risk of
PRECAUTIONS FOR FIRE FIGHTERS AND
exposure to vapour or products of combustion.
SPECIAL PROTECTIVE EQUIPMENT:
NONE
HAZCHEM CODE:

6. ACCIDENTAL RELEASE MEASURES

Spillages are slippery. Ensure adequate ventilation. Keep spectators away 鈥? rope off the area. Avoid
EMERGENCY
accidents, clean up immediately. Wear protective equipment to prevent skin and eye contamination.
PROCEDURES:
Contain the spill and prevent run off into confined areas, drains and waterways.
METHODS AND
Large spills: absorb with dry earth, sand or other similar material. Collect and seal in properly labelled
MATERIALS FOR
drums for disposal in an area approved by local authority by-laws. Wash area down with excess water to
CONTAINMENT AND
remove residual material.
CLEAN UP:
Small spills: may be safely mopped up and area washed with excess water.
Incineration of disposed material is not recommended, as it is unlikely to adequately burn.

7. HANDLING AND STORAGE
Keep containers closed at all times - check regularly for leaks or spills. Transport and store upright.
PRECAUTIONS FOR
Avoid eye contact and repeated or prolonged skin contact. Do not eat, drink or smoke in contaminated
SAFE HANDLING:
areas. Always remove contaminated clothing and wash hands before eating, drinking, smoking or using
the toilet. Wash contaminated clothing and other protective equipment before storage or re-use.
Store in the original container, in a cool dry well-ventilated area out of sunlight and away from
CONDITIONS FOR
incompatible materials and foodstuffs. Ensure containers are fitted with vented closures.
SAFE STORAGE:
Keep containers closed when not in use to ensure contamination does not occur. Ensure containers are
fitted with vented closures and check regularly for leaks. Do not combine part drums of the same
product, as this may be a source of contamination. Do not mix with other chemicals, especially acids.
This material is a Scheduled Poison S5 and must be stored, maintained and used in accordance with
the relevant regulations.

8. EXPOSURE CONTROLS / PERSONAL PROTECTION
No value assigned for this specific material by NOHSC, however as published by NOHSC
NATIONAL EXPOSURE
3
T.W.A. for Sodium hydroxide = 2 mg/m (Peak Limitation)
STANDARDS:
NOHSC have not assigned a value for Sodium Hypochlorite. However, Exposure Standards
for the decomposition of the product are:
3
T.W.A. for Chlorine = 1ppm 3 mg/m S.T.E.L. for Chlorine = Peak Limitation
No biological limit allocated.
BIOLOGICAL LIMIT VALUES:
Ensure ventilation is adequate to maintain air concentrations below Exposure Standards.
ENGINEERING CONTROLS:
Use with local exhaust ventilation or while wearing a respirator. Keep containers closed when
not in use.


Product Name: Page:
GEL STAIN REMOVER 2 of 5
MATERIAL SAFETY DATA SHEET

Protective equipment must be worn: elbow-length impervious gloves, waterproof apron,
PERSONAL PROTECTIVE
overalls, safety boots and safety glasses/goggles and/or full-face shield. Avoid breathing mist,
EQUIPMENT:
sprays or vapours. Where ventilation is not adequate, respiratory protection may be required.
Any chemical cartridge respirator with cartridge(s) providing protection against the compound
of concerns meeting the requirements of AS/NZS 1715 and AS/NZS 1716.

9. PHYSICAL AND CHEMICAL PROPERTIES:
Clear, pale yellow, mobile liquid.
APPEARANCE:
Chlorine odour.
ODOUR:
>12
PH (NEAT):
S.G. 1.06
SPECIFIC GRAVITY OR DENSITY:
No information available.
VAPOUR PRESSURE:
Approx. 93% w/w
PERCENT VOLATILES:
No information available.
BOILING POINT / RANGE:
No information available.
FREEZING / MELTING POINT:
The product is water based and is fully soluble in water.
SOLUBILITY:
No known fire hazard.
FLASH POINT:
No information available.
FLAMMABILITY LIMITS:
No information available.
IGNITION TEMPERATURE:
5 months from manufacturing date (when stored as directed).
SHELF LIFE:
None.
OTHER:

10. STABILITY AND REACTIVITY
The product is not stable - the amount of available chlorine slowly diminishes.
CHEMICAL STABILITY:
Cool storage prolongs viability. The shelf life is 5 months.
Do not combine part drums of the same product, as this may be a source of
CONDITIONS TO AVOID:
contamination.
Acids, aluminium, ammonium salts, tin or zinc coated metals.
INCOMPATIBLE MATERIALS:
The packaging material may burn to emit noxious fumes.
HAZARDOUS DECOMPOSITION PRODUCTS:
DO NOT mix with acidic compounds as toxic Chlorine gas may be liberated.
HAZARDOUS REACTIONS:
Reacts violently with acids. Reacts exothermically on dilution with water. Reacts
with ammonium salts and a toxic ammonia gas may be liberated.

11. TOXICOLOGICAL INFORMATION
No adverse health effects expected if the product is handled in accordance with this Safety Data Sheet and the product label.
Symptoms or effects that may arise if the product is mishandled and overexposure occurs are:
ACUTE EFFECTS
Can be severely irritating if swallowed.
INGESTION:
Can severely irritate the eyes. May cause severe damage.
EYE CONTACT:
Capable of causing skin irritation and may defat the skin with continual use.
SKIN CONTACT:
Vapours, mists and sprays are capable of causing irritation, high concentrations may be nauseating.
INHALATION:
No information available.
LONG TERM EFFECTS:
No toxicity data for this specific product, however toxicity data for the hazardous ingredient is listed
ACUTE TOXICITY /
below.
CHRONIC TOXICITY:
TOXICITY DATA FOR SODIUM HYDROXIDE:
Intrapertioneal LD50 (mouse) 40 mg/kg Oral Lowest Lethal Dose (rabbit) 500 mg/kg
Skin (rabbit) severe irritation 500 mg/24hr Eyes (rabbit) severe irritation 1 mg/30sec rinse
TOXICITY DATA FOR SODIUM HYPOCHLORITE:
Oral LD50 (mice) 5800 mg/kg Eyes (rabbit) moderate irritant




Product Name: Page:
GEL STAIN REMOVER 3 of 5
MATERIAL SAFETY DATA SHEET
12. ECOLOGICAL INFORMATION
Avoid contaminating waterways. The product is highly alkaline. If large spills occurred
ECOTOXICITY:
a water pH rise could be responsible for an environmental effect on aquatic
organisms. If not neutralised this product could potentially be toxic for aquatic
organisms because of its alkalinity (pH> 9 can have an effect on fish, with possible fish
death). pH> 8.5 could be destroying for algae.
AQUATIC TOXICITY DATA FOR SODIUM HYPOCHLORITE:
48hr LC50 (fish) 0.07 鈥? 5.9 mg/L
Surfactants are considered to be biodegradable.
PERSISTENCE AND DEGRADABILITY:
No information available.
MOBILITY:
None.
OTHER:

13. DISPOSAL CONSIDERATIONS
Empty containers should be forwarded to an approved agent for recycling. Avoid
DISPOSAL METHODS:
unauthorised discharge to sewer.
The product is suitable for disposal by landfill through an approved agent. Incineration of
SPECIAL PRECAUTIONS FOR
the product is not recommended, as it is unlikely to adequately burn.
LANDFILL OR INCINERATION:

14. TRANSPORT INFORMATION
Not classified as Dangerous Goods by the criteria of the Australian Dangerous
ROAD AND RAIL TRANSPORT:
Goods Code (ADG Code) for transport by Road and Rail.
NONE
UN NUMBER:
NONE
UN PROPER SHIPPING NAME:
NONE
CLASS AND SUBSIDIARY RISK(S):
NONE
PACKAGING GROUP:
NONE
HAZCHEM CODE:
NONE
INITIAL EMERGENCY RESPONSE GUIDE:
NONE
SEGREGATION DANGEROUS GOODS:

Not classified as Dangerous Goods by the criteria of the International Maritime
MARINE TRANSPORT:
Dangerous Goods Code (IMDG Code) for transport by sea.
NONE
UN NUMBER:
NONE
UN PROPER SHIPPING NAME:
NONE
CLASS AND SUBSIDIARY RISK(S):
NONE
PACKAGING GROUP:
NONE
STOWAGE AND SEGREGATION:

Not classified as Dangerous Goods by the criteria of the International Air Transport
AIR TRANSPORT:
Association (IATA) for transport by air.
NONE
UN NUMBER:
NONE
UN PROPER SHIPPING NAME:
NONE
CLASS AND SUBSIDIARY RISK(S):
NONE
PACKAGING GROUP:
NONE
ERG CODE:

15. REGULATORY INFORMATION

POISONS SCHEDULE (AUST.): 5
Not relevant.
APVMA STATUS:
Not relevant.
TGA STATUS:
All the constituents of this product are listed.
AICS STATUS:
Not relevant.
AQIS STATUS:
Not relevant.
OTHER:


Product Name: Page:
GEL STAIN REMOVER 4 of 5
MATERIAL SAFETY DATA SHEET
16. OTHER INFORMATION

None.
GENERAL INFORMATION:
003
MSDS ISSUE NUMBER:
2 AUGUST 2005
MSDS ISSUE DATE:
In any event, the review and, if necessary, the re-issue of a MSDS shall be no longer than 5 years after the last date of issue.
Electronic versions of the MSDS鈥檚 in a PDF format are also available on our Website at www.cleantec.com.au/product.asp
REASON(S) FOR ISSUE: Update to conform to requirements of NOHSC:2011(2003); 16-header format; 003: error corrected
in hazard category.
THIS ISSUE NUMBER REPLACES ALL PREVIOUS ISSUES.
LITERARY REFERENCE:
SOURCES FOR DATA:

LEGEND:
AICS Australian Inventory of Chemical Substances
APVMA Australian Pesticides and Veterinary Medicines Authority
AQIS Australian Quarantine and Inspection Service
AS Australian Standard (as issued by Standards Australia)
ERP Code Emergency Response Drill Code as found in the ICAO (International Civil Aviation Organisation) Doc 9481
MSDS Material Safety Data Sheet
NOHSC National Occupational Health and Safety Commission
STEL Short Term Exposure Limit - A 15 minute TWA exposure which should not be exceeded at any time during a
working day even if the eight-hour TWA average is within the TWA exposure standard. Exposures at the
STEL should not be longer than 15 minutes and should not be repeated more than four times per day. There
should be at least 60 minutes between successive exposures at the STEL.
TGA Therapeutic Goods Administration
TLV Threshold Limit Value - TLV is a proprietary name registered by the American Conference of Governmental
Industrial Hygienists (ACGIH) and refers to airborne concentrations of substances or levels of physical agents
to which it is believed that nearly all workers may be repeatedly exposed day after day without adverse effect.
TWA Time Weighted Average - The average airborne concentration of a particular substance when calculated over
a normal eight-hour working day, for a five-day working week.
This MSDS has been prepared from current technical data and summarises at the date of issue our best knowledge of the health and safety
information of the product, and in particular how to safely handle and use the product in the workplace.
If clarification or further information is needed to ensure that an appropriate assessment can be made, the user should contact this company.
Our responsibility for products sold is subject to our standard terms and conditions, a copy of which is sent to our customers and is also
available upon request.
This MSDS may only be reproduced in full. Summaries or excerpts from this MSDS may not contain all the relevant information and thus are
not permitted.

End of MSDS




Product Name: Page:
GEL STAIN REMOVER 5 of 5

Search    ENTER KEYWORD
ALL Chemical Property And Toxicity Analysis PAGES IN THIS GROUP
NAMECAS
chppm-apgea_army_mil---D-PHENOTHRIN_MSDS.asp N/A
chppm-apgea_army_mil---Deet_Repellent.asp 134-62-3
chppm-apgea_army_mil---IDA_Kit.asp N/A
chppm-apgea_army_mil---Kill_Zone_Resmethrin_Allethrin.asp N/A
chppm-apgea_army_mil---No_Pest_Strip.asp N/A
chppm-apgea_army_mil---Permethrin_151.asp 52645-53-1
chppm-apgea_army_mil---Permethrin_IDA.asp 52645-53-1
chppm-apgea_army_mil---Permethrin_Spray.asp 52645-53-1 64742-95-6
chppm-apgea_army_mil---permspray.asp N/A
chppm-apgea_army_mil---ratblocklabel.asp N/A
chppm-apgea_army_mil---ratblockmsds.asp N/A
chppm-apgea_army_mil---Resmethrin_Allethrin_MSDS.asp N/A
chrisrichards_com_au---HEPTENAL_MSDS.asp N/A
cleaningsupply_ca---DishwasherMachineLiquid.asp 1310-58-3 7681-52-9
cleantec_com_au---Blue_Brite_Liquid_msds.asp N/A
cleantec_com_au---Blue_Brite_msds.asp 497-19-8 6834-92-0 85117-49-3 68131-39-5
cleantec_com_au---Chlorsan_DW_msds.asp 497-19-8 6834-92-0
cleantec_com_au---Command_msds.asp N/A
cleantec_com_au---Commercial_Strength_Fabric_Softener_msds.asp N/A
cleantec_com_au---Conquer_msds.asp 1310-73-2
cleantec_com_au---CSSD_Access_fs.asp N/A
cleantec_com_au---Dermasoft_Sanitising_Hand_Gel_msds.asp 64-17-5
cleantec_com_au---Deter_msds.asp N/A
cleantec_com_au---Dishwasher_Detergent_msds.asp 497-19-8
cleantec_com_au---Easy_msds.asp N/A
cleantec_com_au---Emmy_msds.asp N/A
cleantec_com_au---Final_msds.asp 7664-38-2
cleantec_com_au---Floral_Mist_msds.asp 64-17-5 68131-39-5
cleantec_com_au---Fresh_Le_Citrus_msds.asp N/A
cleantec_com_au---Gel_Stain_Remover_msds.asp 1310-73-2 7681-52-9
cleantec_com_au---maxifoam_msds.asp 1310-58-3
cleantec_com_au---Nature_Clean_msds.asp N/A
cleantec_com_au---New_Ease_msds.asp 6834-92-0
cleantec_com_au---Power_Fresh_msds.asp 497-19-8
cleantec_com_au---Predator_msds.asp 1310-73-2
cleantec_com_au---Proclean_msds.asp 1310-58-3
cleantec_com_au---Rainshower_msds.asp 64-17-5
cleantec_com_au---Refine_msds.asp 64-17-5 68131-39-5
cleantec_com_au---Scalex_msds.asp 7664-38-2 7647-01-0
cleantec_com_au---Spa-Tec_msds.asp 68424-85-1
cleantec_com_au---Steelcoat_msds.asp 64742-47-8
cleantec_com_au---Super_Solv_msds.asp N/A
cleantec_com_au---Triclean_msds.asp 6834-92-0
cleantec_com_au---Turbo_msds.asp 1310-58-3
cleantec_com_au---Ultimate_msds.asp 1310-73-2 6834-92-0
cleantec_com_au---Ultra_Clean_msds.asp 1310-73-2
cleantec_com_au---Window_and_Spray_and_Wipe_Cleaner_msds.asp N/A
cleantec_com_au---Window_Cleaner_Concentrate_msds.asp 111-76-2
clearcoproducts_com---msds-psf-standard.asp 63148-62-9
coastwidelabs_com---Linoleum_ULO_Stripper_MSDS3710.asp 08-15-9 100-51-6 108-32-7 57-55-6 102-71-6

Free MSDS Search ( Providing 250,000+ Material Properties )
Chemcas.com | Ads link:HBCCHEM.INC