MATERIAL SAFETY DATA SHEET
1. IDENTIFICATION OF THE MATERIAL AND SUPPLIER
PRODUCT NAME: NEW EASE
OTHER NAMES: EXPORT NEW EASE; PACER NEW EASE
RECOMMENDED USE: HARD SURFACE CLEANER
CAMPBELL CLEANTEC (ABN 92 009 657 489)
SUPPLIER NAME:
AUSTRALIA: NEW ZEALAND:
32 PERIVALE STREET, 11-13 FALCON STREET,
ADDRESS:
PARNELL, AUCKLAND, 1001
DARRA, QLD, 4076
GENERAL ENQUIRIES: + 61 7 3710 3200 NZ: (09) 379 8745
TELEPHONE:
CUSTOMER SERVICE: 1800 077 240 NZ: (09) 379 8745
GENERAL ENQUIRIES: + 61 7 3710 3210 NZ: (09) 336 1354
FAX:
CUSTOMER SERVICE: + 61 7 3710 3207 NZ: (09) 336 1354
AUSTRALIA:
EMERGENCY TELEPHONE NUMBER:
1800 628 724 (ALL HOURS)
NEW ZEALAND: 0800 734 607 (ALL HOURS)
ALL OTHER + 61 7 3710 3184 (ALL HOURS)
INTERNATIONAL:
2. HAZARDS IDENTIFICATION
Not classified as hazardous according to the criteria of NOHSC.
HAZARD CLASSIFICATION:
Not classified as a dangerous good according to the criteria of ADG Code (see section 14).
Classified as schedule 5 according to the criteria of SUSDP (see section 15).
NONE
HAZARD CATEGORY:
NONE
RISK PHRASES:
NONE
SAFETY PHRASES:
The information contained in this MSDS is specific to the product when handled and used neat. This product when diluted may not require the
same control measures as the neat product. Check with your technical representative if in doubt.
3. COMPOSITION / INFORMATION ON INGREDIENTS
INGREDIENT CAS No. PROPORTION (% w/w)
The ingredients below are considered either hazardous, dangerous goods or poison scheduled according to the criteria of NOHSC, ADG
Code and SUSDP (respectively) at the levels used in the product.
Disodium Trioxosilicate 6834-92-0 < 10%
The ingredients below are not considered either hazardous, dangerous goods or poison scheduled according to the criteria of NOHSC,
ADG Code and SUSDP (respectively) at the levels used in the product.
Anionic surfactant < 10%
Solvent < 10%
Builder < 10%
Dye < 10%
Water > 60%
Product Name: Page:
NEW EASE 1 of 5
MATERIAL SAFETY DATA SHEET
4. FIRST AID MEASURES
For advice, contact a Poisons Information Centre (Phone Australia 131126, New Zealand
INGESTION:
0800 764 766) or a doctor. If swallowed, do NOT induce vomiting.
If in eyes, hold eyelids apart and flush the eye continuously with running water. Continue flushing
EYE CONTACT:
until advised to stop by the Poisons Information Centre or a doctor, or for at least 15 minutes.
If skin or hair contact occurs, remove contaminated clothing and flush skin and hair with running
SKIN CONTACT:
water. Continue flushing until advised to stop by the Poisons Information Centre or a doctor.
Remove from source of exposure to fresh air. Seek medical assistance if the effects persist.
INHALATION:
** SHOW THIS SAFETY DATA SHEET TO A DOCTOR **
Potable water should be available to rinse eyes or skin. Provide eye baths and safety showers.
FIRST AID FACILITIES:
Treat symptomatically.
NOTES TO PHYSICIAN:
5. FIRE FIGHTING METHODS
Water spray, foam, carbon dioxide or dry chemical powder.
SUITABLE EXTINGUISHING MEDIA:
The product is non-combustible; however, the packaging material may burn to emit
HAZARDS FROM COMBUSTION:
noxious fumes. May react with aluminium, zinc, tin and alloys and may liberate
hydrogen gas which is extremely flammable.
Fire fighters should wear self-contained breathing apparatus to minimise risk of
PRECAUTIONS FOR FIRE FIGHTERS AND
exposure to vapour or products of combustion.
SPECIAL PROTECTIVE EQUIPMENT:
None
HAZCHEM CODE:
6. ACCIDENTAL RELEASE MEASURES
Spillages are slippery. Ensure adequate ventilation. Keep spectators away 鈥? rope off the area. Avoid
EMERGENCY
accidents, clean up immediately. Wear protective equipment to prevent skin and eye contamination.
PROCEDURES:
Contain the spill and prevent run off into confined areas, drains and waterways.
METHODS AND
Large spills: absorb with dry earth, sand or other similar material. Collect and seal in properly labelled
MATERIALS FOR
drums for disposal in an area approved by local authority by-laws. Neutralise excess with dilute acid
CONTAINMENT AND
such as acetic acid and wash area down with excess water to remove residual material.
CLEAN UP:
Small spills: Neutralise with dilute acid such as acetic acid and safely mop up the spill. The area may be
washed with excess water.
Incineration of disposed material is not recommended, as it is unlikely to adequately burn.
7. HANDLING AND STORAGE
Keep containers closed at all times - check regularly for leaks or spills. Transport and store upright.
PRECAUTIONS FOR
Avoid eye contact and repeated or prolonged skin contact. Do not eat, drink or smoke in contaminated
SAFE HANDLING:
areas. Always remove contaminated clothing and wash hands before eating, drinking, smoking or using
the toilet. Wash contaminated clothing and other protective equipment before storage or re-use.
Store in the original container, in a cool, dry, well-ventilated area out of sunlight and away from
CONDITIONS FOR
incompatible materials and foodstuffs.
SAFE STORAGE:
Keep containers closed when not in use to ensure contamination does not occur. Do not combine part
drums of the same product, as this may be a source of contamination. Do not mix with other chemicals.
Do not store in galvanised containers or use die-cast zinc or aluminium bungs; plastic bungs should be
used. Keep containers closed when not in use - check regularly for leaks.
This material is a Scheduled Poison S5 and must be stored, maintained and used in accordance with
the relevant regulations.
8. EXPOSURE CONTROLS / PERSONAL PROTECTION
No value assigned for this specific material by NOHSC.
NATIONAL EXPOSURE STANDARDS:
No biological limit allocated.
BIOLOGICAL LIMIT VALUES:
Ensure ventilation is adequate to maintain air concentrations below Exposure
ENGINEERING CONTROLS:
Standards.
Use with local exhaust ventilation or while wearing a respirator. Keep containers closed
when not in use.
Product Name: Page:
NEW EASE 2 of 5
MATERIAL SAFETY DATA SHEET
The product is alkaline. Protective equipment should be worn. Risk assessments should
PERSONAL PROTECTIVE
always be conducted to identify the hazards and in turn determine the appropriate
EQUIPMENT:
personal protective equipment for the hazard.
Whilst protective equipment is not mandatory, examples of recommended protective
equipment are listed below.
Protective gloves: elbow-length natural rubber, nitrile, neoprene or PVC impervious
gloves. Always check with the glove manufacturer or your personal protective
equipment supplier regarding the correct type of glove to use. Consult AS/NZS 2161 for
further information.
Eye protection: safety glasses/goggles with side shield protection. Consult AS/NZS
1336 and AS/NZS 1337 for further information.
Clothing and footwear: waterproof apron, trousers, long sleeved shirt, closed in shoes
and/or safety footwear. Consult AS/NZS 2210 and AS/NZS 2919 for further information.
Respiratory Protection: Avoid breathing mist, sprays or vapours. Where ventilation is
not adequate, respiratory protection may be required meeting the requirements of
AS/NZS 1715 and AS/NZS 1716.
9. PHYSICAL AND CHEMICAL PROPERTIES:
Clear, dark blue, mobile liquid.
APPEARANCE:
Solvent odour.
ODOUR:
12.8 to 13.6
PH (NEAT):
S.G. 1.07
SPECIFIC GRAVITY OR DENSITY:
No information available.
VAPOUR PRESSURE:
Approximately 88.0% at 100.0掳C
PERCENT VOLATILES:
No information available.
BOILING POINT / RANGE:
No information available.
FREEZING / MELTING POINT:
No information available.
SOLUBILITY:
No known fire hazard.
FLASH POINT:
Not relevant.
FLAMMABILITY LIMITS:
Not relevant.
IGNITION TEMPERATURE:
2 years from manufacturing date (when stored as directed).
SHELF LIFE:
None.
OTHER:
10. STABILITY AND REACTIVITY
Stable under normal conditions of use. The shelf life is years.
CHEMICAL STABILITY:
Do not combine part drums of the same product, as this may be a source of
CONDITIONS TO AVOID:
contamination.
Strong acids and galvanised soft metals.
INCOMPATIBLE MATERIALS:
The packaging material may burn to emit noxious fumes. Corrosive sodium oxide
HAZARDOUS DECOMPOSITION PRODUCTS:
vapours may be generated at high temperature.
Reacts exothermically with acids. Prolonged contact with the neat product may
HAZARDOUS REACTIONS:
affect galvanised soft metals.
11. TOXICOLOGICAL INFORMATION
No adverse health effects expected if the product is handled in accordance with this Safety Data Sheet and the product label.
Symptoms or effects that may arise if the product is mishandled and overexposure occurs are:
ACUTE EFFECTS
Can be severely irritating if swallowed, may result in cramps, vomiting and diarrhoea
INGESTION:
Moderate to severe eye irritation and if left untreated may cause severe damage.
EYE CONTACT:
Mild to moderate skin irritation and may defat the skin with continual use. If left untreated may cause
SKIN CONTACT:
severe irritation and burning.
Mists or sprays may produce respiratory irritation.
INHALATION:
No information available.
LONG TERM EFFECTS:
Product Name: Page:
NEW EASE 3 of 5
MATERIAL SAFETY DATA SHEET
No toxicity data for this specific product, however toxicity data for the hazardous ingredient is listed
ACUTE TOXICITY /
below.
CHRONIC TOXICITY:
TOXICITY DATA FOR DISODIUM TRIOXOSILICATE:
Oral LD50 (rat): 1153 mg/kg Oral LD50 (mice): 770 mg/kg.
Skin (human): 250 mg/ 24 Hr / Severe. Oral (dog) LDLo: 250 mg/kg
12. ECOLOGICAL INFORMATION
Avoid contaminating waterways. The product is highly alkaline. If large spills occurred
ECOTOXICITY:
a water pH rise could be responsible for an environmental effect on aquatic
organisms. If not neutralised this product could potentially be toxic for aquatic
organisms because of its alkalinity (pH> 9 can have an effect on fish, with possible fish
death). pH> 8.5 could be destroying for algae.
ECOTOXICITY DATA FOR DISODIUM TRIOXOSILICATE:
Bacteria-30 min. ECO(Pseudomonas putida) >1000mg/l
LC50 Gambusia affinis 2320 mg/l/96h (pH 8.9-10.1)
EC50 Daphnia 247 mg/l/100h (pH 9.1)
Product is considered readily biodegradable to AS4351.
PERSISTENCE AND DEGRADABILITY:
No information available.
MOBILITY:
None.
OTHER:
13. DISPOSAL CONSIDERATIONS
Empty containers should be forwarded to an approved agent for recycling. Avoid
DISPOSAL METHODS:
unauthorised discharge to sewer.
The product is suitable for disposal by landfill through an approved agent. Incineration of
SPECIAL PRECAUTIONS FOR
the product is not recommended, as it is unlikely to adequately burn.
LANDFILL OR INCINERATION:
14. TRANSPORT INFORMATION
Not classified as Dangerous Goods by the criteria of the Australian Dangerous
ROAD AND RAIL TRANSPORT:
Goods Code (ADG Code) for transport by Road and Rail.
NONE
UN NUMBER:
NONE
UN PROPER SHIPPING NAME:
NONE
CLASS AND SUBSIDIARY RISK(S):
NONE
PACKAGING GROUP:
NONE
HAZCHEM CODE:
NONE
INITIAL EMERGENCY RESPONSE GUIDE:
NONE
SEGREGATION DANGEROUS GOODS:
Not classified as Dangerous Goods by the criteria of the International Maritime
MARINE TRANSPORT:
Dangerous Goods Code (IMDG Code) for transport by sea.
NONE
UN NUMBER:
NONE
UN PROPER SHIPPING NAME:
NONE
CLASS AND SUBSIDIARY RISK(S):
NONE
PACKAGING GROUP:
NONE
STOWAGE AND SEGREGATION:
Not classified as Dangerous Goods by the criteria of the International Air Transport
AIR TRANSPORT:
Association (IATA) for transport by air.
NONE
UN NUMBER:
NONE
UN PROPER SHIPPING NAME:
NONE
CLASS AND SUBSIDIARY RISK(S):
NONE
PACKAGING GROUP:
NONE
ERG CODE:
Product Name: Page:
NEW EASE 4 of 5
MATERIAL SAFETY DATA SHEET
15. REGULATORY INFORMATION
POISONS SCHEDULE (AUST.): 5
Not relevant.
APVMA STATUS:
Not relevant.
TGA STATUS:
All the constituents of this product are listed.
AICS STATUS:
IOA is available on request. (New Ease only)
AQIS STATUS:
None.
OTHER:
16. OTHER INFORMATION
It is alkaline. Use good industrial hygiene.
GENERAL INFORMATION:
003
MSDS ISSUE NUMBER:
12 SEPTEMBER 2006
MSDS ISSUE DATE:
In any event, the review and, if necessary, the re-issue of a MSDS shall be no longer than 5 years after the last date of issue.
Electronic versions of the MSDS鈥檚 in a PDF format are also available on our Website at www.cleantec.com.au/product.asp
REASON(S) FOR ISSUE: 002: Update to conform to requirements of NOHSC:2011(2003); 16-header format.
003: Addition of NZ contact details. No new regulatory information.
THIS ISSUE NUMBER REPLACES ALL PREVIOUS ISSUES.
LITERARY REFERENCE:
SOURCES FOR DATA:
LEGEND:
AICS Australian Inventory of Chemical Substances
APVMA Australian Pesticides and Veterinary Medicines Authority
AQIS Australian Quarantine and Inspection Service
AS Australian Standard (as issued by Standards Australia)
ERP Code Emergency Response Drill Code as found in the ICAO (International Civil Aviation Organisation) Doc 9481
MSDS Material Safety Data Sheet
NOHSC National Occupational Health and Safety Commission
STEL Short Term Exposure Limit - A 15 minute TWA exposure which should not be exceeded at any time during a
working day even if the eight-hour TWA average is within the TWA exposure standard. Exposures at the
STEL should not be longer than 15 minutes and should not be repeated more than four times per day. There
should be at least 60 minutes between successive exposures at the STEL.
TGA Therapeutic Goods Administration
TLV Threshold Limit Value - TLV is a proprietary name registered by the American Conference of Governmental
Industrial Hygienists (ACGIH) and refers to airborne concentrations of substances or levels of physical agents
to which it is believed that nearly all workers may be repeatedly exposed day after day without adverse effect.
TWA Time Weighted Average - The average airborne concentration of a particular substance when calculated over
a normal eight-hour working day, for a five-day working week.
This MSDS has been prepared from current technical data and summarises at the date of issue our best knowledge of the health and safety
information of the product, and in particular how to safely handle and use the product in the workplace.
If clarification or further information is needed to ensure that an appropriate assessment can be made, the user should contact this company.
Our responsibility for products sold is subject to our standard terms and conditions, a copy of which is sent to our customers and is also
available upon request.
This MSDS may only be reproduced in full. Summaries or excerpts from this MSDS may not contain all the relevant information and thus are
not permitted.
End of MSDS
Product Name: Page:
NEW EASE 5 of 5
|