Ablebond 2033SC Page 1 of 5
May 8,鈥?02
*** MATERIAL SAFETY DATA SHEET ***
_________________________________________________________________________
1. CHEMICAL PRODUCT AND COMPANY IDENTIFICATION
_________________________________________________________________________
PRODUCT NAME....................... Ablebond 2033SC
SYNONYM NAME(S).................... Modified Ester Resin
Ablestik Laboratories
Subsidiary of National Starch and Chemical Company
20021 Susana Road
Rancho Dominguez, CA 90221
USA
Emergency Telephone:
1-800-424-9300 (24 hours, CHEMTREC)
_________________________________________________________________________
2. COMPOSITION/INFORMATION ON INGREDIENTS
_________________________________________________________________________
COMPONENT CAS NUMBER CONCENTRATION RANGE (%)
Ester resin Proprietary 15-40
Organic peroxide Proprietary 1-5
Acrylate resin Proprietary 10-30
Polymeric resin Proprietary 5-10
Fused silica/ 60676-86-0/ 30-60
Silica 7631-86-9
_________________________________________________________________________
3. HAZARDS IDENTIFICATION
_________________________________________________________________________
Emergency Overview
Red paste.
Danger! May cause burns to eyes and irritation to skin. May cause skin
sensitization. Risk of sensitization depends on duration and
level of exposure.
EYE................................ Irritating, and will injure eye tissue
if not removed promptly.
SKIN CONTACT....................... Irritating to the skin. May be
absorbed through the skin. May cause
skin sensitization, a partial or
whole-body dermatitic rash experienced
after exposure, however minimal.
INHALATION......................... Irritating and/or toxic vapors may
be released at elevated temperatures.
Vapors may be irritating to
respiratory system and nasal passages.
INGESTION.......................... May irritate mouth, throat, esophagus
and stomach.
Ablebond 2033SC Page 2 of 5
May 8,鈥?02
*** MATERIAL SAFETY DATA SHEET ***
_________________________________________________________________________
4. FIRST-AID MEASURES
_________________________________________________________________________
EYE................................ Immediately flush eyes with large
amounts of water for at least 15
minutes, lifting upper and lower
lids. If irritation persists, get
medical attention.
SKIN CONTACT....................... Flush exposed areas thoroughly with
water until all chemical is removed.
Remove contaminated clothing and
launder before reuse. If irritation
persists, get medical attention.
INHALATION......................... Remove to fresh air. Get medical
attention if irritation persists.
INGESTION.......................... Get medical attention.
_________________________________________________________________________
5. FIREFIGHTING MEASURES
_________________________________________________________________________
AUTOIGNITION....................... Not available
FLASH POINT........................ Not available
EXTINGUISHING MEDIA................ Foam; CO2; Dry chemical
SPECIAL FIREFIGHTING PROCEDURES.... Fire fighters should be equipped
with self-contained breathing
apparatus to protect against
potentially toxic and irritating
fumes.
FIRE & EXPLOSION HAZARDS........... Emits toxic fumes under fire
conditions.
UPPER EXPLOSION LIMIT (%).......... Not Available
LOWER EXPLOSION LIMIT (%).......... Not Available
_________________________________________________________________________
6. ACCIDENTAL RELEASE MEASURES
_________________________________________________________________________
SPILL AND LEAK PROCEDURES.......... Scrape up and place in suitably
labeled container for disposal.
For safety and environmental precautions, please review entire Material
Safety Data Sheet for necessary information.
_________________________________________________________________________
7. HANDLING AND STORAGE
_________________________________________________________________________
- 400 C
STORAGE TEMPERATURE................
SPECIAL SENSITIVITY................ Heat
HANDLING/STORAGE................... Empty containers may contain product
residue; follow MSDS and label
warnings even after they have been
emptied.
VENTILATION REQUIREMENTS........... Vent curing oven to outdoors.
Ablebond 2033SC Page 3 of 5
May 8,鈥?02
*** MATERIAL SAFETY DATA SHEET ***
_________________________________________________________________________
8. EXPOSURE CONTROLS/PERSONAL PROTECTION
_________________________________________________________________________
COMPONENT EXPOSURE LIMITS
OSHA: PEL-TWA: Respirable; 0.1 mg/m3
Fused silica
ACGIH: TLV-TWA: Respirable; 0.1 mg/m3
OSHA: PEL-TWA: Total dust; 10 mg/m3
Silica [Nuisance dust]
Respirable; 5 mg/m3
ACGIH: TLV-TWA: Total dust; 10 mg/m3
Respirable; 3 mg/m3
VENTILATION REQUIREMENTS........... Vent curing oven to outdoors.
EYE PROTECTION REQUIREMENTS........ Wear safety glasses with side shields.
GLOVE REQUIREMENTS................. Employee must wear appropriate
protective gloves to prevent contact
with this substance.
CLOTHING REQUIREMENTS.............. Employee must wear appropriate
protective clothing and equipment to
prevent any possibility of skin
contact with this substance.
CHANGE/REMOVAL OF CLOTHING......... If product is spilled on clothes,
remove immediately and launder
before reuse.
WASH REQUIREMENTS.................. If contact has occurred, wash with
soap and water before eating.
RESPIRATOR REQUIREMENTS............ NIOSH approved respirator if
required. Self-contained breathing
apparatus in emergency and
non-routine situations.
_________________________________________________________________________
9. PHYSICAL AND CHEMICAL PROPERTIES
_________________________________________________________________________
PURE SUBSTANCE OR MIXTURE.......... Mixture
PHYSICAL FORM...................... Paste
APPEARANCE/ODOR.................... Red
ODOR THRESHOLD..................... Not available
PH AS IS........................... Not available
BOILING POINT...................... Not available
MELTING/FREEZING POINT............. Not Applicable
SOLUBILITY IN WATER................ Insoluble
PARTITION COEFFICIENT
(n-octanol/water)................ Not Applicable
SPECIFIC GRAVITY (WATER=1)......... 1.33
BULK DENSITY....................... Not available
EVAPORATION RATE................... Not available
VAPOR PRESSURE (mmHg).............. Not available
VAPOR DENSITY (air = 1)............ Not available
VISCOSITY.......................... Not available
VOLATILES.......................... Not available
VOLATILE ORGANIC COMPOUNDS......... Not available
AUTOIGNITION....................... Not available
FLASH POINT........................ Not available
OXIDIZING PROPERTIES............... Not available
Ablebond 2033SC Page 4 of 5
May 8,鈥?02
*** MATERIAL SAFETY DATA SHEET ***
_________________________________________________________________________
10. STABILITY AND REACTIVITY
_________________________________________________________________________
STABILITY.......................... Stable
MATERIALS TO AVOID................. Oxidizing agents, acids, and
alkaline materials.
HAZARDOUS DECOMPOSITION PRODUCTS... Carbon dioxide, carbon monoxide,
oxides of nitrogen and unknown
organics. Thermal decomposition
products are hazardous and/or toxic
_________________________________________________________________________
11. TOXICOLOGICAL INFORMATION
_________________________________________________________________________
CHRONIC (LONG TERM) EFFECTS OF EXPOSURE
ROUTE OF ENTRY..................... Skin, Inhalation
EFFECTS OF CHRONIC EXPOSURE........ Repeated contact may cause the skin
sensitization.
The toxicological properties of this
product have not been fully evaluated.
Use of good industrial hygiene
practices is required. Avoid direct
contact with skin or eyes. Do not
ingest or inhale.
TARGET ORGANS...................... Skin
CARCINOGEN......................... No
SENSITIZER......................... Yes
_________________________________________________________________________
12. ECOLOGICAL INFORMATION
_________________________________________________________________________
Not available.
_________________________________________________________________________
13. DISPOSAL CONSIDERATIONS
_________________________________________________________________________
WASTE DISPOSAL METHODS............. Waste disposal should be in
accordance with existing federal,
state and local environmental
regulations.
EMPTY CONTAINER WARNINGS........... Empty containers may contain product
residue; follow MSDS and label
warnings even after they have been
emptied.
_________________________________________________________________________
14. TRANSPORTATION INFORMATION
_________________________________________________________________________
DOT INFORMATION
DOT SHIPPING NAME.................. Not regulated
UN/ID Number....................... NA
Ablebond 2033SC Page 5 of 5
May 8,鈥?02
*** MATERIAL SAFETY DATA SHEET ***
Class ............................. NA
Packaging Group ................... NA
Subsidiary risk ................... NA
Label ............................. NA
_________________________________________________________________________
15. REGULATORY INFORMATION
_________________________________________________________________________
TSCA............................... All components are on the TSCA
inventory.
STATE LAWS......................... Warning: This product contains the
following chemicals known to the State
of California to cause cancer:
Methylene chloride, Epichlorohydrin
and Benzene are present in trace
amounts.
Warning: This product contains the
following chemical known to the State
of California to cause birth defects
or other reproductive harm :
Benzene, Epichlorohydrin and Toluene
are present in trace amount.
SARA/TITLE III, THIS PRODUCT CONTAINS (OR IS) A TOXIC CHEMICAL FOR
ROUTINE ANNUAL CHEMICAL RELEASE REPORTING UNDER SECTION 313:
None
The information given and the recommendations made herein apply to our
product(s) alone and are not combined with other product(s). Such are
based on our research and on data from other reliable sources and are
believed to be accurate. No guaranty of accuracy is made. It is the
purchaser's responsibility before using any product to verify this data
under their own operating conditions and to determine whether the product
is suitable for their purposes.
_________________________________________________________________________
16. OTHER INFORMATION
_________________________________________________________________________
MSDS DATE.......................... May 8,鈥?02
CHANGES SINCE PREVIOUS ISSUE....... -
FOR REGULATORY INFORMATION, CONTACT:
Health & Safety Coordinator
Ablestik Laboratories
National Starch & Chemical Company
20021 Susana Road
Rancho Dominguez, CA 90221
USA
Telephone: 310-764-4600
FAX: 310-763-2725
|