MATERIAL SAFETY DATA SHEET
CrackBuster Pro
HMIS
HEALTH 1
FLAMMABILITY 0
REACTIVITY 0
B
PERSONAL PROTECTION
1. Product And Company Identification
Supplier Manufacturer
CUSTOM BUILDING PRODUCTS CUSTOM BUILDING PRODUCTS
10400 Pioneer Blvd., Unit #3 10400 Pioneer Blvd., Unit #3
Santa Fe Springs, CA 90670 UNITED STATES Santa Fe Springs, CA 90670 UNITED STATES
Company Contact: GEORGE MARCINA Company Contact: GEORGE MARCINA
Telephone Number: (562) 968-2980 Ext 103 Telephone Number: (562) 968-2980 Ext 103
FAX Number: (562) 903-2697 FAX Number: (562) 903-2697
E-Ma il: georgem@cbpmail.net E-Ma il: georgem@cbpmail.net
Web Site: www.custombuildingproducts.com Web Site: www.custombuildingproducts.com
Supplier Emergency Contacts & Phone Number Manufacturer Emergency Contacts & Phone Number
GEORGE MARCINA: (562) 968-2980 GEORGE MARCINA: (562) 968-2980
Issue Date: 03/16/2007
Product Name: CrackBuster Pro
Chemical Name: Rubber Modified Asphalt
CAS Number: Not Established
Chemical Family: Asphalt
Chemical Formula: Mixture
MSDS Number: 800
Product Code: PolyG
2. Composition/Information On Ingredients
Ingredient CAS Percent Of
Name Number Total Weight
AluminumFoil Not establish 0 -2
Bitumen, Cracking Residue 8052-42-4 65 - 84
Calcium Carbonate 471-34-1 0 - 15
Nylon as fabric or film Not Establish 0 -5
Petroleum Hydrocarbon Resin 68527-25-3 0 -8
Polyester as fabric or film Not establish 0 -8
Polyethylene as fabric or film 9002-88-4 0 -8
Polypropylene as fabric or film 9003-07-0 0 -8
Proprietary Ingredient Not Establish 0 -5
Styrene - Butadiene 9003-55-8 0 - 15
Talc 14807-96-6 0 - 15
Page 1 of 5
MATERIAL SAFETY DATA SHEET
CrackBuster Pro
3. Hazards Identification
Primary Routes(s) Of Entry
Skin and Inhalation
Eye Hazards
Not likely. Mechanical irritation.
Skin Hazards
Slight irritation
Ingestion Hazards
Not likely.
Inhalation Hazards
Inhalation could occur if product is heated to molten state.
Chronic/Carcinogenicity Effects
Contains ingredients listed by IARC as Group 3 - Not classifiable as to carcinogenic or non carcinogenic to humans.
4. First Aid Measures
Eye
In case of contact, hold eyelids apart and immediately flush eyes with plenty of water for at least 15 minutes. Get
medical attention immediately.
Skin
In case of irritation wash thoroughly with water and soap. If irritation persist, get medical attention.
Ingestion
If there is any discomfort from ingestion, consult a physician.
Inhalation
Remove to fresh air. Consult a physician immediately if irritation persists.
5. Fire Fighting Measures
Flash Point: >525 掳F
Flash Point Method: COC
Lower Explosive Limit: N/A
Upper Explosive Limit: N/A
Extinguishing Media
Water, Foam, CO2
Fire Fighting Instructions
Wear self-contained breathing apparatus
6. Accidental Release Measures
No Data Available...
7. Handling And Storage
Handling And Storage Precautions
Store in dry, ventilated areas, away from heat. Do not store in temperatures above 200 F
Work/Hygienic Practices
Maintain good personal hygiene and housekeeping practices.
8. Exposure Controls/Personal Protection
No Data Available...
Page 2 of 5
MATERIAL SAFETY DATA SHEET
CrackBuster Pro
8. Exposure Controls/Personal Protection - Continued
Eye/Face Protection
Protect from mechanical intrusion.
Skin Protection
Use impervious gloves.
Respiratory Protection
Local exhaust is usually satisfactory.
Ingredient(s) - Exposure Limits
Bitumen, Cracking Residue
NIOSH - PEL - 5mg/m3 - fumes
ACGIH - TLV - 5 mg/m3 - fumes
Calcium Carbonate
ACGIH TLV-TWA 10 mg/m3
OSHA PEL-TWA 15 mg/m3
OSHA PEL-TWA 5 mg/m3
Talc
ACGIH TLV-TWA 2 mg/m3
OSHA PEL-TWA 20 mppcf
9. Physical And Chemical Properties
Appearance
Sheet like material, in rolls.
Odor
Possible slight odor.
Chemical Type: Mixture
Physical State: Solid
Melting Point: > 200 掳F
Boiling Point: N/A 掳F
Specific Gravity: 1.0 - 1.3
Percent VOCs: 0 g/l
Vapor Density: N/A
Solubility: NONE
Evaporation Rate: N/A
10. Stability And Reactivity
Sta bility: STABLE
Hazardous Polymerization: WILL NOT OCCUR.
Conditions To Avoid (Stability)
High temperature will cause material to melt.
Hazardous Decomposition Products
C0, CO2, Smoke,
11. Toxicological Information
Chronic/Carcinogenicity
Contains ingredients listed by IARC as Group 3 - Not classifiable as to carcinogenic or non carcinogenic to humans.
Ingredient(s) - Carcinogenicity
Bitumen, Cracking Residue
Listed In The IARC Monographs
Nylon as fabric or film
Page 3 of 5
MATERIAL SAFETY DATA SHEET
CrackBuster Pro
11. Toxicological Information - Continued
Ingredient(s) - Carcinogenicity - Continued
Listed In The IARC Monographs
Polyester as fabric or film
Listed In The IARC Monographs
Polyethylene as fabric or film
Listed In The IARC Monographs
Polypropylene as fabric or film
Listed In The IARC Monographs
Styrene - Butadiene
Listed In The IARC Monographs
Talc
Listed In The IARC Monographs
Bitumen, Styrene-butadiene,Talc, Polyethylene, Polypropylene, Polyester and Nylon were evaluated by IARC and are
listed as Group 3 - Not classifiable as to carcinogenic or non carcinogenic to humans.
12. Ecological Information
No Data Available...
13. Disposal Considerations
Dispose in accordance with Sate, Local and Federal regulations.
RCRA Information
Not considered RCRA waste.
14. Transport Information
DOT Shipping Label
NOT REGULATED
15. Regulatory Information
Ingredient(s) - State Regulations
Calcium Carbonate
Pennsylvania - Workplace Hazard
Styrene - Butadiene
California - Proposition 65
Talc
New Jersey - Workplace Hazard
Pennsylvania - Workplace Hazard
Massachusetts - Hazardous Substance
16. Other Information
HMIS Rating
He a lth: 1
Fire : 0
Re a ctivity: 0
Personal Protection: B
Revision/Preparer Information
MSDS Preparer: GEORGE MARCINA
MSDS Preparer Phone Number: (323) 582-0846
This MSDS Supersedes A Previous MSDS Dated: 10/15/2002
Page 4 of 5
MATERIAL SAFETY DATA SHEET
CrackBuster Pro
Disclaimer
THE INFORMATION PRESENTED HERE IS BELIEVED TO BE ACCURAE BUT IS NOT WARRANTED TO BE,
WHETHER ORIGINATING WITH THE COMPANY OR NOT. RECIPIENTS ARE ADVISED TO CONFIRM IN
ADVANCE OF NEED, THAT THE INFORMATION IS CURRENT, APPLICABLE, AND SUITABLE TO THEIR
CIRCUMSTANCES.
CUSTOM BUILDING PRODUCTS
Printed Using MSDS Generator鈩? 2000
Page 5 of 5
|