Duniway Part #: MPO-180
CITGO Pacemaker庐 HV-68 Oil
Material Safety Data Sheet
CITGO Petroleum Corporation
634105001
MSDS No.
P.O. Box 3758
Hazard Rankings
Tulsa, OK 74102-3758
Revision Date 02/04/2003
HMIS NFPA
0 0
Health Hazard
IMPORTANT: Read this MSDS before handling or disposing of this product and pass this information on to
employees, customers and users of this product.
1 1
Fire Hazard
Emergency Overview 0
Reactivity 0
Liquid.
Physical State
* = Chronic Health Hazard
Light amber to amber Mild petroleum odor
Color Odor
Protect eyes from misting or spraying material. Protective Equipment
Protect exposed skin from repeated or prolonged exposure.
Do not store material in open or unmarked containers. Minimum Recommended
See Section 8 for Details
Spills may create a slipping hazard.
SECTION 1: IDENTIFICATION
CITGO Pacemaker庐 HV-68 Oil (800) 248-4684
Trade Name Technical Contact
(918) 495-4700
Product Number 634105001 Medical Emergency
Mixture. (800) 424-9300
CAS Number CHEMTREC Emergency
(United States Only)
Lubricating oil
Product Family
Lubricating oil;
Synonyms
CITGO SAP Product Code No.: 634105001
SECTION 2: COMPOSITION
Concentration (%)
Component Name(s) CAS Registry No.
1) Distillates, petroleum, solvent-re ned heavy para nic 64741-88-4 100
SECTION 3: HAZARDS IDENTIFICATION
Also see Emergency Overview and Hazard Ratings on the top of Page 1 of this MSDS.
Major Route(s) of Entry Skin contact.
Signs and Symptoms of Acute Exposure
No signi cant adverse health e ects are expected to occur upon short-term exposure.
Inhalation
This product can cause transient mild eye irritation with short-term contact with liquid sprays or mists.
Eye Contact
This material can cause mild skin irritation from prolonged or repeated skin contact. Injection under the
Skin Contact
skin can cause in ammation and swelling. Injection of pressurized hydrocarbons can cause severe,
permanent tissue damage. Initial symptoms may be minor. Injection of petroleum hydrocarbons requires
immediate medical attention.
MSDS No. Revision Date
634105001 Page Number: 1
02/04/2003 Continued on Next Page
CITGO Pacemaker庐 HV-68 Oil
If swallowed, large volumes of material can cause generalized depression, headache, drowsiness, nausea,
Ingestion
vomiting and diarrhea. Smaller doses can cause a laxative effect. If aspirated into the lungs, liquid can
cause lung damage.
Contains a petroleum-based mineral oil. Prolonged or repeated skin contact can cause mild irritation and
Chronic Health Effects
inflammation characterized by drying, cracking, (dermatitis) or oil acne. Repeated or prolonged inhalation
Summary
of petroleum-based mineral oil mists at concentrations above applicable workplace exposure levels can
cause respiratory irritation or other pulmonary effects.
Conditions Aggravated Medical conditions aggravated by exposure to this material may include pre-existing skin disorders.
by Exposure
This material may cause damage to the following organs: skin.
Target Organs
This product does not contain any components at concentrations above 0.1% which are considered
Carcinogenic Potential
carcinogenic by OSHA, IARC or NTP.
OSHA Hazard Classification is indicated by an "X" in the box adjacent to the hazard title. If no "X" is present, the product does not exhibit the
hazard as defined in the OSHA Hazard Communication Standard (29 CFR 1910.1200).
OSHA Health Hazard Classification OSHA Physical Hazard Classification
Explosive Pyrophoric
Irritant Toxic Combustible
Oxidizer Water-reactive
Sensitizer Highly Toxic Flammable
Carcinogenic Organic Peroxide Unstable
Corrosive Compressed Gas
SECTION 4: FIRST AID MEASURES
Take proper precautions to ensure your own health and safety before attempting rescue or providing first aid. For more specific
information, refer to Exposure Controls and Personal Protection in Section 8 of this MSDS.
Vaporization is not expected at ambient temperatures. This material is not expected to cause
Inhalation
inhalation-related disorders under anticipated conditions of use. In case of overexposure, move the
person to fresh air.
Check for and remove contact lenses. Flush eyes with cool, clean, low-pressure water while
Eye Contact
occasionally lifting and lowering eyelids. Seek medical attention if excessive tearing, redness, or pain
persists.
If burned by hot material, cool skin by quenching with large amounts of cool water. For contact with
Skin Contact
product at ambient temperatures, remove contaminated shoes and clothing. Wipe off excess material.
Wash exposed skin with mild soap and water. Seek medical attention if tissue appears damaged or if
pain or irritation persists. Thoroughly clean contaminated clothing before reuse. Discard contaminated
leather goods. If material is injected under the skin, seek medical attention immediately.
Do not induce vomiting unless directed to by a physician. Do not give anything to drink unless directed
Ingestion
to by a physician. Never give anything by mouth to a person who is not fully conscious. If significant
amounts are swallowed or irritation or discomfort occurs, seek medical attention immediately.
The viscosity range of the product represented by this MSDS is 100 to 400 SUS at 100掳 F. Accordingly,
Notes to Physician
upon ingestion there is a low to moderate risk of aspiration. Careful gastric lavage may be considered
to evacuate large quantities of material. Subcutaneous or intramuscular injection requires prompt
surgical debridement.
SECTION 5: FIRE FIGHTING MEASURES
NFPA Class-IIIB combustible material. Slightly combustible!
NFPA Flammability
Classification
OPEN CUP: 238掳C (460掳F) (Cleveland.).
Flash Point Method
No data. No data.
Lower Flammable Limit Upper Flammable Limit
Not available.
Autoignition Temperature
634105001 Page Number: 2
02/04/2003 Continued on Next Page
MSDS No. Revision Date
CITGO Pacemaker庐 HV-68 Oil
Carbon dioxide, carbon monoxide, smoke, fumes, unburned hydrocarbons and trace oxides of sulfur
Hazardous
and/or nitrogen.
Combustion Products
This material can burn but will not readily ignite. This material will release vapors when heated above
Special Properties
the flash point temperature that can ignite when exposed to a source of ignition. In enclosed spaces,
heated vapor can ignite with explosive force. Mists or sprays may burn at temperatures below the flash
point.
Use dry chemical, foam, Carbon Dioxide or water fog.
Extinguishing Media
Firefighters must use full bunker gear including NIOSH-approved positive pressure self-contained
Protection of Fire Fighters
breathing apparatus to protect against potential hazardous combustion or decomposition products and
oxygen deficiencies.
SECTION 6: ACCIDENTAL RELEASE MEASURES
Take proper precautions to ensure your own health and safety before attempting spill control or clean-up. For more specific
information, refer to the Emergency Overview on Page 1, Exposure Controls and Personal Protection in Section 8 and Disposal
Considerations in Section 13 of this MSDS.
Do not touch damaged containers or spilled material unless wearing appropriate protective equipment.
Slipping hazard; do not walk through spilled material. Stop leak if you can do so without risk. For small
spills, absorb or cover with dry earth, sand, or other inert non-combustible absorbent material and place
into waste containers for later disposal. Contain large spills to maximize product recovery or disposal.
Prevent entry into waterways or sewers. In urban area, cleanup spill as soon as possible. In natural
environments, seek cleanup advice from specialists to minimize physical habitat damage. This material
will float on water. Absorbent pads and similar materials can be used. Comply with all laws and
regulation
SECTION 7: HANDLING AND STORAGE
Avoid contamination and extreme temperatures to minimize product degradation. Empty containers
Handling
may contain product residues that can ignite with explosive force. Do not pressurize, cut, weld, braze
solder, drill, grind or expose containers to flames, sparks, heat or other potential ignition sources.
Consult appropriate federal, state and local authorities before reusing, reconditioning, reclaiming,
recycling or disposing of empty containers and/or waste residues of this product.
Keep container closed. Do not store with strong oxidizing agents. Do not store at elevated
Storage
temperatures. Avoid storing product in direct sunlight for extended periods of time. Consult appropriate
federal, state and local authorities before reusing, reconditioning, reclaiming, recycling or disposing of
empty containers or waste residues of this product.
SECTION 8: EXPOSURE CONTROLS AND PERSONAL PROTECTION
Provide exhaust ventilation or other engineering controls to keep the airborne concentrations of mists
Engineering Controls
and/or vapors below the recommended exposure limits (see below). An eye wash station and safety
shower should be located near the work-station.
Personal protective equipment should be selected based upon the conditions under which this material
Personal Protective
is used. A hazard assessment of the work area for PPE requirements should be conducted by a
Equipment
qualified professional pursuant to OSHA regulations. The following pictograms represent the minimum
requirements for personal protective equipment. For certain operations, additional PPE may be
required.
Safety glasses equipped with side shields are recommended as minimum protection in industrial
Eye Protection
settings. Wear goggles and/or face shield if splashing or spraying is anticipated. Wear goggles and
face shield if material is heated above 125掳F (51掳C). Have suitable eye wash water available.
634105001 Page Number: 3
02/04/2003 Continued on Next Page
MSDS No. Revision Date
CITGO Pacemaker庐 HV-68 Oil
Use gloves constructed of chemical resistant materials such as neoprene or heavy nitrile rubber if
Hand Protection
frequent or prolonged contact is expected. Use heat-protective gloves when handling product at
elevated temperatures.
Use clean and impervious protective clothing (e.g., neoprene or Tyvek庐) if splashing or spraying
Body Protection
conditions are present. Protective clothing may include long-sleeve outer garment, apron, or lab coat.
If significant contact occurs, remove oil-contaminated clothing as soon as possible and promptly
shower. Launder contaminated before reuse or discard. Wear heat protective boots and protective
clothing when handling material at elevated temperatures.
Vaporization is not expected at ambient temperatures. Therefore, the need for respiratory protection is
Respiratory Protection
not anticipated under normal use conditions and with adequate ventilation. If elevated airborne
concentrations above applicable workplace exposure levels are anticipated, a NIOSH-approved organic
vapor respirator equipped with a dust/mist prefilter should be used. Protection factors vary depending
upon the type of respirator used. Respirators should be used in accordance with OSHA requirements
(29 CFR 1910.134).
Use good personal hygiene practices. Wash hands and other exposed skin areas with plenty of mild
General Comments
soap and water before eating, drinking, smoking, use of toilet facilities, or leaving work. DO NOT use
gasoline, kerosene, solvents or harsh abrasives as skin cleaners. Since specific exposure
standards/control limits have not been established for this product, the "Oil Mist, Mineral" exposure
limits shown below are suggested as minimum control guidelines.
Occupational Exposure Guidelines
Substance Applicable Workplace Exposure Levels
1) Oil Mist, Mineral ACGIH (United States).
TWA: 5 mg/m3
STEL: 10 mg/m3
OSHA (United States).
TWA: 5 mg/m3
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
Color Light amber to Mild petroleum odor
Liquid. Odor
Physical State
amber
>1 (Air = 1)
Vapor
0.88 (Water = 1) Not Applicable.
Specific Gravity pH
Density
Not available.
Not available. Melting/Freezing
Boiling Point/Range
Point
<0.001 kPa (<0.01 mmHg) (at 20掳C) Viscosity (cSt @ 40掳C) 65
Vapor Pressure
Insoluble in cold water. Negligible volatility
Solubility in Water Volatile
Characteristics
Additional Properties Gravity, 潞API (ASTM D287) = 30.0 @ 60潞 F
Density = 7.30 Lbs/gal.
Viscosity (ASTM D2161) = 339 SUS @ 100潞 F
SECTION 10: STABILITY AND REACTIVITY
Hazardous Polymerization Not expected to occur.
Stable.
Chemical Stability
Keep away from extreme heat, sparks, open flame, and strongly oxidizing conditions.
Conditions to Avoid
Strong oxidizers.
Materials Incompatibility
No additional hazardous decomposition products were identified other than the combustion products
Hazardous
identified in Section 5 of this MSDS.
Decomposition Products
634105001 Page Number: 4
02/04/2003 Continued on Next Page
MSDS No. Revision Date
CITGO Pacemaker庐 HV-68 Oil
SECTION 11: TOXICOLOGICAL INFORMATION
For other health-related information, refer to the Emergency Overview on Page 1 and the Hazards Identification in Section 3 of this
MSDS.
Toxicity Data Distillates, petroleum, solvent-refined heavy paraffinic:
ORAL (LD50): Acute: >5000 mg/kg [Rat].
DERMAL (LD50): Acute: >2000 mg/kg [Rabbit].
Distillates, petroleum, solvent-refined heavy paraffinic:
Mineral oil mists derived from highly refined oils are reported to have low acute and sub-acute toxicities
in animals. Effects from single and short-term repeated exposures to high concentrations of mineral oil
mists well above applicable workplace exposure levels include lung inflammatory reaction, lipoid
granuloma formation and lipoid pneumonia. In acute and sub-acute studies involving exposures to
lower concentrations of mineral oil mists at or near current work place exposure levels produced no
significant toxicological effects. In long term studies (up to two years) no carcinogenic effects have
been reported in any animal species tested. Analyses conducted by method IP 346 indicate that the
polycyclic aromatic concentration of this mineral oil is below 3.0 weight percent.
SECTION 12: ECOLOGICAL INFORMATION
Analysis for ecological effects has not been conducted on this product. However, if spilled, this product
Ecotoxicity
and any contaminated soil or water may be harmful to human, animal, and aquatic life. Also, the
coating action associated with petroleum and petroleum products can be harmful or fatal to aquatic life
and waterfowl.
An environmental fate analysis has not been conducted on this specific product. Plants and animals
Environmental Fate
may experience harmful or fatal effects when coated with petroleum-based products. Petroleum-based
(mineral) lube oils will normally float on water. In stagnant or slow-flowing waterways, an oil layer can
cover a large surface area. As a result, this oil layer might limit or eliminate natural atmospheric oxygen
transport into the water. With time, if not removed, oxygen depletion in the waterway may be sufficient
to cause a fish kill or create an anaerobic environment.
SECTION 13: DISPOSAL CONSIDERATIONS
Hazard characteristic and regulatory waste stream classification can change with product use. Accordingly, it is the responsibility
of the user to determine the proper storage, transportation, treatment and/or disposal methodologies for spent materials and
residues at the time of disposition.
Conditions of use may cause this material to become a "hazardous waste", as defined by federal or
state regulations. It is the responsibility of the user to determine if the material is a RCRA "hazardous
waste" at the time of disposal. Transportation, treatment, storage and disposal of waste material must
be conducted in accordance with RCRA regulations (see 40 CFR 260 through 40 CFR 271). State
and/or local regulations may be more restrictive. Contact the RCRA/Superfund Hotline at (800)
424-9346 or your regional US EPA office for guidance concerning case specfic disposal issues.
SECTION 14: TRANSPORT INFORMATION
Not regulated by the U.S. Department of Transportation as a hazardous material.
DOT Status
Not regulated.
Proper Shipping Name
Not regulated.
Hazard Class Not applicable.
Packing Group(s)
Not regulated.
UN/NA ID
A Reportable Quantity (RQ) has not been established for this material.
Reportable Quantity
634105001 Page Number: 5
02/04/2003 Continued on Next Page
MSDS No. Revision Date
CITGO Pacemaker庐 HV-68 Oil
Not applicable.
Emergency Response Guide
Placards No.
2911990
HAZMAT STCC No.
Not a DOT "Marine Pollutant"
MARPOL III Status
per 49 CFR 171.8.
SECTION 15: REGULATORY INFORMATION
This product and/or its components are listed on the Toxic Substances Control Act (TSCA) inventory.
TSCA Inventory
The Superfund Amendments and Reauthorization Act of 1986 (SARA) Title III requires facilities subject
SARA 302/304
to Subparts 302 and 304 to submit emergency planning and notification information based on Threshold
Planning Quantities (TPQs) and Reportable Quantities (RQs) for "Extremely Hazardous Substances"
listed in 40 CFR 302.4 and 40 CFR 355. No components were identified.
The Superfund Amendments and Reauthorization Act of 1986 (SARA) Title III requires facilities subject
SARA 311/312
to this subpart to submit aggregate information on chemicals by "Hazard Category" as defined in 40
CFR 370.2. This material would be classified under the following hazard categories:
No SARA 311/312 hazard categories identified.
This product contains the following components in concentrations above de minimis levels that are
SARA 313
listed as toxic chemicals in 40 CFR Part 372 pursuant to the requirements of Section 313 of SARA: No
components were identified.
The Comprehensive Environmental Response, Compensation, and Liability Act of 1980 (CERCLA)
CERCLA
requires notification of the National Response Center concerning release of quantities of "hazardous
substances" equal to or greater than the reportable quantities (RQ's) listed in 40 CFR 302.4. As defined
by CERCLA, the term "hazardous substance" does not include petroleum, including crude oil or any
fraction thereof which is not otherwise specifically designated in 40 CFR 302.4. Chemical substances
present in this product or refinery stream that may be subject to this statute are: None identified.
This material is classified as an oil under Section 311 of the Clean Water Act (CWA) and the Oil
CWA
Pollution Act of 1990 (OPA). Discharges or spills which produce a visible sheen on waters of the United
States, their adjoining shorelines, or into conduits leading to surface waters must be reported to the
EPA's National Response Center at (800) 424-8802.
This material may contain the following components which are known to the State of California to cause
California
cancer, birth defects or other reproductive harm, and may be subject to the requirements of California
Proposition 65
Proposition 65 (CA Health & Safety Code Section 25249.5):
Toluene: 0.0008%
Petroleum Oil
New Jersey
Right-to-Know Label
No additional regulatory remarks.
Additional Regulatory
Remarks
SECTION 16: OTHER INFORMATION
Refer to the top of Page 1 for the HMIS and NFPA Hazard Ratings for this product.
REVISION INFORMATION
2.0
Version Number
02/04/2003
Revision Date
Printed on 02/04/2003.
Print Date
ABBREVIATIONS
AP: Approximately EQ: Equal >: Greater Than <: Less Than NA: Not Applicable ND: No Data NE: Not Established
ACGIH: American Conference of Governmental Industrial Hygienists AIHA: American Industrial Hygiene Association
634105001 Page Number: 6
02/04/2003 Continued on Next Page
MSDS No. Revision Date
CITGO Pacemaker庐 HV-68 Oil
IARC: International Agency for Research on Cancer NTP: National Toxicology Program
NIOSH: National Institute of Occupational Safety and Health OSHA: Occupational Safety and Health Administration
NPCA: National Paint and Coating Manufacturers Association HMIS: Hazardous Materials Information System
NFPA: National Fire Protection Association EPA: US Environmental Protection Agency
DISCLAIMER OF LIABILITY
THE INFORMATION IN THIS MSDS WAS OBTAINED FROM SOURCES WHICH WE BELIEVE ARE RELIABLE. HOWEVER, THE
INFORMATION IS PROVIDED WITHOUT ANY WARRANTY, EXPRESSED OR IMPLIED REGARDING ITS CORRECTNESS. SOME
INFORMATION PRESENTED AND CONCLUSIONS DRAWN HEREIN ARE FROM SOURCES OTHER THAN DIRECT TEST DATA ON THE
SUBSTANCE ITSELF. THIS MSDS WAS PREPARED AND IS TO BE USED ONLY FOR THIS PRODUCT. IF THE PRODUCT IS USED AS
A COMPONENT IN ANOTHER PRODUCT, THIS MSDS INFORMATION MAY NOT BE APPLICABLE. USERS SHOULD MAKE THEIR
OWN INVESTIGATIONS TO DETERMINE THE SUITABILITY OF THE INFORMATION OR PRODUCTS FOR THEIR PARTICULAR
PURPOSE.
THE CONDITIONS OR METHODS OF HANDLING, STORAGE, USE, AND DISPOSAL OF THE PRODUCT ARE BEYOND OUR CONTROL
AND MAY BE BEYOND OUR KNOWLEDGE. FOR THIS AND OTHER REASONS, WE DO NOT ASSUME RESPONSIBILITY AND
EXPRESSLY DISCLAIM LIABILITY FOR LOSS, DAMAGE OR EXPENSE ARISING OUT OF OR IN ANY WAY CONNECTED WITH
HANDLING, STORAGE, USE OR DISPOSAL OF THE PRODUCT.
***** END OF MSDS *****
|