24 Madison Road, Fairfield, New Jersey 07004, USA
Tel: 800-771-JEEN (5336), Tel: 973-439-1401, Fax: 973-439-1402,
email: info@jeen.com , Website: www.jeen.com
MATERIAL SAFETY DATA SHEET
Section 1 鈥? Company and Product Identification
Issued by: JEEN International Corporation Chemtrec Emergency Telephone # 800-424-9300
24 Madison Road Chemtrec Int鈥檒 Tel.# 703-527-3887(Collect Calls Accepted)
Fairfield, New Jersey 07004 Issuance Date: March 11, 2002
Tel#: 973-439-1401 Revised: June 2, 2003
Product Trade Name: JEESILC UAF
INCI: Propoxytetramethyl Piperidinyl Dimethicone
Chemical Name: Amino Polydimethyl Siloxane
Chemical Family: Silicone
CAS Number: Mixture
HMIS: Health (NFPA): 1 Flammability (NFPA): 1 Reactivity (NFPA): 0
Section 2 鈥? Hazardous Ingredients
All components in this product are listed in the TSCA Inventory.
CAS Number Ingredients Wt% Exposure Limits
None
Any components that are listed above are hazardous as defined in 29 CFR 1910.1200
Section 3 鈥? Hazards Identification
HMIS Code: Health: 1 Flammability: 1 Reactivity: 0
Acute Effects:
Eyes: Direct contact irritates slightly with redness and swelling, possible corneal injury.
Skin: Single, prolonged exposure (hours) causes no known effect. Several repeated, prolonged exposures may cause
slight irritation.
Inhalation: No irritation to nose or throat expected. No injury is likely from relatively short exposure.
Ingestion: Amounts transferred to the mouth by fingers, etc., during normal operations should not cause injury.
Comment(s): No known, adverse chronic health effects, but unnecessary exposure to any chemical should be avoided. This
product, as with any chemical may enhance allergic conditions on certain people. There are no known, medical
conditions that might be aggravated by exposure to this product.
Special Hazards:
Carcinogens: None known.
Mutagens: None known.
Reproductive Toxins: None known.
Sensitizers: None known.
Section 4 鈥? First Aid Measures
Eyes: Immediately upon exposure to the eyes, they should be flushed with plenty of freight water, ensuring that under both
the upper and lower lids are rinsed well for five to ten minutes. GET MEDICAL ATTENTION if irritation persists.
Skin: Exposed skin should be thoroughly rinsed with fresh water to move the product from the expose area as soon as
possible. If irritation persists, CONSULT A PHYSICIAN.
Inhalation: No problem.
Ingestion: Data regarding the effects of ingestion is not available. If product is ingested, CONSULT A PHYSICIAN.
Comment(s): Although this product is considered to be a safe product, the user assumes the liability to ensure that safe and
prudent procedures are use in handling and using the product in order to ensure that personnel are not dangerously
exposing the eyes and skin without proper safeguards.3
Page No. 1 of 3 鈥? MSDS - JEESILC UAF
24 Madison Road, Fairfield, New Jersey 07004, USA
Tel: 800-771-JEEN (5336), Tel: 973-439-1401, Fax: 973-439-1402,
email: info@jeen.com , Website: www.jeen.com
MATERIAL SAFETY DATA SHEET
Page No. 2 of 3 鈥? MSDS 鈥? JEESILC UAF
Section 5 鈥? Fire and Explosion Hazard
Flash Point: >120掳C (248掳F)
Method: PMCC
Auto Ignition Temperature: Not known.
Flammability Limits in Air: Not Determined
Extinguishing Media: All standard fire fighting media.
Hazardous Decomposition
Products: This product contains methyl-polysiloxane which can generate formaldehyde at approximately
300掳F (150掳C) and above in atmospheres that contain oxygen. Other decomposition products are
carbon oxides, sulfur oxides, nitrogen oxides, and silica (crystalline).
Section 6 鈥? Accidental Release Measures
Containment/Clean-Up: Disposal of collected product, residues, and clean-up material may be governmentally regulated.
Observe all applicable local, state and federal waste management regulations. Mop up , wip up, or
soak up with absorbent and contain for salvage or disposal. For large spills, provide diking or other
appropriate containment to keep material from spreading. Clean any remaining slippery surfaces
Containment/Clean-Up: by appropriate techniques, such as several moppings or swabbings with appropriate solvents:
Continued鈥? washing with mild, caustic detergents or solutions; or high-pressure steam for large area. For non-
silicones, use typical industrial cleaning or high-pressure steam for large area. For non-silicones,
use typical industrial cleaning materials. Observe any safety precautions applicable to the cleaning
material being used. Observe all personal protection equipment recommendations described in
Section 8. Local, state and federal reporting requirements may apply to spills or releases of this
material into the environment. See applicable regulatory compliance information in Section 15.
Note: See Section 8 for Personal Protection Equipment for Spills.
Section 7 鈥? Handling and Storage
Handling: No special precautions.
Storage: No special precautions.
Section 8 鈥? Exposure Control/Personal Protection
Engineering Controls: Local Exhaust: None should be needed. General Ventilation: Recommended
Personal Protective Equipment for
Routine Handling: Eyes: Use proper protection (Safety glasses as a minimum).
Skin: Washing at mealtime and end of shift is adequate.
Inhalation: No respiratory protection should be needed.
Suitable Respirator: None should be needed.
Personal Protective Equipment
For Spills: Eyes: Use proper protection (safety glasses as a minimum).
Skin: Washing at mealtime and end of shift is adequate
Inhalation/Suitable
Respirator: No respirator protection should be needed.
Precautionary Measures: Avoid eye contact. Use reasonable care.
Comments: None
Note: These precautions are for room temperature handling. Use at elevated temperatures, or in aerosol/spray applications, may require added
precautions.
Section 9 鈥? Physical and Chemical Properties
Physical Appearance: Clear to Hazy
Color: Clear
Odor: Slight Ammonia Odor
Specific Gravity @ 25掳C: 1.0 @ 25掳C
Solubility in Water: Insoluble
Viscosity: 10,000 to 100,000 cps @ 25掳C
pH: Not applicable
Note: The above information is not intended for use in preparing product specifications. Contact manufacturer before writing specifications.
24 Madison Road, Fairfield, New Jersey 07004, USA
Tel: 800-771-JEEN (5336), Tel: 973-439-1401, Fax: 973-439-1402,
email: info@jeen.com , Website: www.jeen.com
MATERIAL SAFETY DATA SHEET
Page No. 3 of 3 鈥? MSDS 鈥? JEESILC UAF
Section 10 鈥? Stability and Reactivity
Stability: Stable [X] Unstable [ ]
Hazardous Polymerization: Hazardous polymerization will not occur.
Conditions to Avoid: None.
Materials to Avoid: Oxidizing material can cause a reactions.
Comments: None
Section 11 鈥? Toxicological
Complete information is not yet available.
Section 12 鈥? Ecological Information
Complete information is not yet available.
Section 13 鈥? Disposal Considerations
Disposal Method: Disposal should be made in accordance with federal state and local regulations. Incineration recommended in
approved incinerator according to federal state and local regulations.
Section 14 鈥? Transportation Information
Property Shipping Name (49 CFR 172.101): Silicone
UN Number:
Hazard Name (49 CFR 172.101): Non-Hazardous
Section 15 鈥? Regulatory Information
O.S.H.A. Status: Contents of this MSDS comply with the OSHA Hazard Communication Standard 29 CFR 1910.1200.
EINICS Status: All chemical substances found in this product are listed.
TSCA Status: All chemical substances found in this product comply with the Toxic Substances Control Act inventory
reporting requirements.
DSL (Canada): All chemical substances found in this product are listed.
ERA SARA Title III
Chemical Listing: Section 302 Extremely Hazardous Substances: None
Section 304 C.E.R.C.L.A. Hazardous Substances: RQ
Section 312 Hazardous Class: Acute: No
Chronic: No
Fire: No
Pressure: No
Reactive: No
Section 313 Toxic Chemicals: None present or none present in
Regulated quantities.
These data are offered in good faith as typical values and not as a Product Specifications. No warranty, either expressed or implied, is hereby made. The recommended
industrial hygiene and safe handling procedures are believed to be generally applicable; however, each user should review these recommendations in the specific context of
intended use and determine whether they are appropriate.
|