The compa
ny that
published
this work
is now
in a joint
venture co
mpany
named Aus
tralian Tu
be Mills.
For techni
cal suppor
t or sale
enquiries
please cont
act
Australian
Tube Mills.
Part 2 ā? Structural Products Contents
Section Page
Structural CHS Grade C250L0
2-3
Specifications
2-5
Section Properties
2-7
Mass & Bundling
Structural CHS Grade C350L0
2-9
Specifications
2-11
Section Properties
2-13
Mass & Bundling
Structural RHS DualGradeĀ® C350L0/C450L0
2-15
Specifications
2-17
Section Properties
Notes:
2-21
Mass & Bundling
Disclaimer ā? Whilst every care has been taken in the preparation
Structural SHS DualGradeĀ® C350L0/C450L0 of this information, Smorgon Steel Tube Mills, and its agents accept
2-25
Specifications no liability for the accuracy of the information supplied. The company
2-27
Section Properties expressly disclaims all and any liability to any person whether a
purchaser of any product, or otherwise in respect of anything done or
2-31
Mass & Bundling
omitted to be done and the consequences of anything done or omitted
Structural RHS Grade C350L0 to be done, by any such person in reliance, whether in whole or in
2-35
Specifications part upon the whole or any part of this publication.
2-36
Section Properties Product availability & other information ā? As the section, grade
and finish of all products are subject to continuous improvement,
Structural SHS Grade C350L0
reference should be made to the SSTM QUICK REFERENCE PRODUCT
2-37
Specifications AVAILABILITY GUIDE (QRPAG) for information on the availability
2-38
Section Properties of listed sections and associated finishes. The QRPAG is found
at the beginning of this publication.
Always ensure that you are using current information on the SSTM
product range. This can be verified by comparing the document
version date (noted at the bottom of the page) with the current version
date of each publication. The current version date of the QRPAG, this
and other SSTM publications can be obtained by referring to www.
smorgonsteel.com.au/tubemills or by contacting SSTM.
Smorgon Steel Tube Mills A.B.N. 22 010 469 977. PO Box 246 Sunnybank, Queensland 4109 Australia Telephone +61 7 3246 2600 Facsimile +61 7 3246 2660 E-mail tubemills@smorgonsteel.com.au Internet www.smorgonsteel.com.au/tubemills
DECEMBER 2006 2-1
PART 0 PART 9
PART 1 PART 2 PART 3 PART 4 PART 5 PART 6 PART 7 PART 8
Quick Reference Product Material Safety
General Information Structural Products Piping Products Other Products Steel Grades Mill Finishes Mill Processing Fabrication
Availability Guide Data Sheets (MSDS)
Blank Page
Smorgon Steel Tube Mills A.B.N. 22 010 469 977. PO Box 246 Sunnybank, Queensland 4109 Australia Telephone +61 7 3246 2600 Facsimile +61 7 3246 2660 E-mail tubemills@smorgonsteel.com.au Internet www.smorgonsteel.com.au/tubemills
DECEMBER 2006 2-2
Structural CHS C250L0 ā? Specifications
Technical Specifications This primer paint finish is applied in-line using the *Note: DN 15 conforms to PTMA 9701. DN stands for
patented KleenKoteĀ® process and is supplied in the Nominal Size and replaces NB (Nominal Bore).
Australian Standards following coating thicknesses: May exclude some wall thicknesses and finishes.
Structural CHS Grade C250L0 is manufactured Red & Black ________________Target 12 microns with
_ Contact your Smorgon Steel Tube Mills representative
and tested to comply with the requirements of the ________________________ average at 8-10 microns for further details.
1 1
CHS CHS
following specifications: Note: Non-standard finishes, such as NoKote, are
Non-Standard Lengths 2 2
C250L0 C250L0
available if ordered prior to rollings. Conditions apply.
AS 1074 ā? Steel tubes and tubulars for 3 3
KleenKoteĀ® HotDipGal
Special orders of non-standard pack lengths of
Refer to manufacturer for details.
ordinary service.
Structural CHS Grade C250L0 are available (conditions
See Quick Reference Product Availability Guide (Part 0)
AS 1163 ā? Structural steel hollow sections
apply). Check with your distributor for details.
General Description
(Grade C250L0). for further information on availability.
Minimum Length:
HotDipGal Finish
AS/NZS 4792 ā? Hot-dip galvanized (zinc) coatings
Manufacturing Process
4.2 m
on ferrous hollow sections, applied by a continuous Ā® ________________
(DN 20 ā? DN 100) KleenKote
or a specialized process (Section 2). Structural CHS Grade C250L0, for general
5.3 m
Galvanized (Hot-dip) Ā® _______________
(DN 125 ā? DN 150) KleenKote
Structural CHS Grade C250L0 with HotDipGal finish mechanical and low pressure reticulation and
_________________ 5.0 m
Mechanical Properties (DN 20 ā? DN 100) HotDipGal
is galvanized and tested to meet the requirements structural applications, is manufactured by cold-forming
(DN 125 ā? DN 150) HotDipGal _______________ 5.3 m
_
Structural CHS Grade C250L0 has the following of Section 2 of AS/NZS 4792. and high frequency Electric Resistance Welding (ERW)
Maximum Length:
mechanical properties: of steel strip. The cold-forming process enhances the
Minimum coating mass _________ 300 g/m2 each side
(DN 20 ā? DN 40) KleenKoteĀ® _________________ 8.0 m strength, hardness and surface finish of the pipe and
Minimum Yield Strength __________________ 250 MPa The coating adherence of the galvanizing is satisfactory for
(DN 50 ā? DN 100) KleenKoteĀ® _______________ 12.0 m produces product to tight dimensional tolerances.
Minimum Tensile Strength _______________ 320 MPa
_ the pipe to be bent to a radius 6 times the diameter of the
(DN 80 ā? DN 150) KleenKoteĀ® _______________ 13.0 m
Further Information
pipe up to 60.3mm OD in accordance with AS/NZS 4792.
Minimum Elongation in 5.65āSo _______________ 22%
_________________ 7.2 m
L0 __ guaranteed impact properties at 0Ā°C to AS 1163
_ See Quick Reference Product Availability Guide (Part 0) (DN 20 ā? DN 100) HotDipGal
For further information refer to the Smorgon Steel Tube Mills:
(DN 125 ā? DN 150) HotDipGal ______________ 12.0 m
_
for further information on availability.
Tolerances Product Solutions Guide.
Note: Contact your Smorgon Steel Tube Mills
End Finish (Mill Processing)
Tolerances for Structural CHS Grade C250L0 are representative for lengths outside this range.
compliant with AS 1163. See Dimensional Tolerances Plain Ends only.
Thickness
in Part 1 for more information. Refer to Pipe Grade C250L0 in Piping Products
(Part 3) for Threaded End options. Structural CHS Grade C250L0 are available in
Supply Conditions medium (M), heavy (H) and extra heavy (XH) wall
Standard Lengths
KleenKoteĀ® Finish thickness. These thicknesses are identified by the
Standard length for Structural CHS Grade C250L0: following end colour codes:
Structural CHS Grade C250L0 with KleenKoteĀ®
(DN 15* ā? DN 150 CHS) KleenKoteĀ®/HotDipGal __ 6.5 m Medium (M) ________________________________ Blue
finish is supplied in the following surface colours:
Grade C250L0 Extra Heavy Pipe is also available Heavy (H) _________________________________
_ Red
Red Black
on request. Extra Heavy (XH) ______________________ No Colour
_
Smorgon Steel Tube Mills A.B.N. 22 010 469 977. PO Box 246 Sunnybank, Queensland 4109 Australia Telephone +61 7 3246 2600 Facsimile +61 7 3246 2660 E-mail tubemills@smorgonsteel.com.au Internet www.smorgonsteel.com.au/tubemills
DECEMBER 2006 2-3
PART 0 PART 9
PART 1 PART 2 PART 3 PART 4 PART 5 PART 6 PART 7 PART 8
Quick Reference Product Material Safety
General Information Structural Products Piping Products Other Products Steel Grades Mill Finishes Mill Processing Fabrication
Availability Guide Data Sheets (MSDS)
Blank Page
Smorgon Steel Tube Mills A.B.N. 22 010 469 977. PO Box 246 Sunnybank, Queensland 4109 Australia Telephone +61 7 3246 2600 Facsimile +61 7 3246 2660 E-mail tubemills@smorgonsteel.com.au Internet www.smorgonsteel.com.au/tubemills
DECEMBER 2006 2-4
Structural CHS C250L0 ā? Section Properties calculated to AS 1163 in accordance with AS 4100
Properties for Design to AS 4100
Dimensions and Ratios Properties
External Gross Torsion Torsion Form
Designation About any axis About any axis
Nominal Mass Surface Area Section Area Constant Modulus Factor
do
Size per m
do t per m per t Ag I Z S r J C kf Compactness Ze
t
10 6 mm4 10 3 mm 3 10 3 mm 3 10 6 mm4 10 3 mm 3 10 3 mm 3
m 2 /m m 2 /t mm 2
mm mm DN kg/m mm (C,N,S)
1 1
CHS CHS
150 H 21.3 0.519 24.4 30.6 2710 8.65 105 138 56.5 17.3 209 1.00 138
165.1 5.4 C
x CHS 2 2
C250L0 C250L0
5.0 3 3
150 M 19.7 0.519 26.3 33.0 2510 8.07 97.7 128 56.6 16.1 195 1.00 128 KleenKoteĀ® HotDipGal
CHS C
125 H 17.9 0.439 24.5 25.9 2280 5.14 73.7 97.4 47.5 10.3 147 1.00 97.4
139.7 5.4 C
x CHS
5.0 125 M 16.6 0.439 26.4 27.9 2120 4.81 68.8 90.8 47.7 9.61 138 1.00 90.8
CHS C
Notes:
100 H 14.5 0.359 24.8 21.2 1850 2.75 48.0 64.1 38.5 5.49 96.1 1.00 64.1
114.3 5.4 C
x CHS
4.5 100 M 12.2 0.359 29.5 25.4 1550 2.34 41.0 54.3 38.9 4.69 82.0 1.00 54.3
CHS C 1. For Grade C250L0: fy = 250 MPa and fu = 320 MPa;
90 H 11.9 0.319 26.8 20.3 1520 1.77 34.9 46.7 34.2 3.55 69.9 1.00 46.7
101.6 5.0 C
x CHS fy = yield stress used in design; fu = tensile strength
used in design; as defined in AS 4100.
4.0 90 M 9.63 0.319 33.2 25.4 1230 1.46 28.8 38.1 34.5 2.93 57.6 1.00 38.1
CHS C
80 XH 12.1 0.279 23.1 15.1 1540 1.33 30.0 40.7 29.4 2.66 59.9 1.00 40.7
88.9 5.9 2. C = Compact Section; N = Non-Compact Section;
C
x CHS
S = Slender Section (as defined in AS 4100).
5.0 80 H 10.3 0.279 27.0 17.8 1320 1.16 26.2 35.2 29.7 2.33 52.4 1.00 35.2
CHS C
3. Grade C250L0 to AS 1163 is cold-formed and is therefore allocated
4.0 80 M 8.38 0.279 33.3 22.2 1070 0.963 21.7 28.9 30.0 1.93 43.3 1.00 28.9
CHS C
the CF residual stresses classification in AS 4100.
65 XH 10.2 0.239 23.4 12.9 1300 0.807 21.2 29.1 24.9 1.61 42.4 1.00 29.1
76.1 5.9 C
x CHS
4. Grade C250L0: M = Medium; H = Heavy; XH = Extra Heavy.
4.5 65 H 7.95 0.239 30.1 16.9 1010 0.651 17.1 23.1 25.4 1.30 34.2 1.00 23.1
CHS C
5. LiteOil and NoKote are available in all sections on request.
3.6 65 M 6.44 0.239 37.1 21.1 820 0.540 14.2 18.9 25.7 1.08 28.4 1.00 18.9
CHS C
50 XH 7.31 0.189 25.9 11.2 931 0.354 11.8 16.3 19.5 0.709 23.5 1.00 16.3
60.3 5.4 C
x CHS 6. Refer to Piping Products for Pipe in Grade C250L0
meeting AS 1074.
4.5 50 H 6.19 0.189 30.6 13.4 789 0.309 10.2 14.0 19.8 0.618 20.5 1.00 14.0
CHS C
3.6 50 M 5.03 0.189 37.6 16.8 641 0.259 8.58 11.6 20.1 0.517 17.2 1.00 11.6
CHS C
40 H 4.37 0.152 34.7 12.1 557 0.138 5.70 7.87 15.7 0.275 11.4 1.00 7.87
48.3 4.0 C
x CHS
3.2 40 M 3.56 0.152 42.6 15.1 453 0.116 4.80 6.52 16.0 0.232 9.59 1.00 6.52
CHS C
32 H 3.79 0.133 35.2 10.6 483 0.0899 4.24 5.92 13.6 0.180 8.48 1.00 5.92
42.4 4.0 C
x CHS
3.2 32 M 3.09 0.133 43.1 13.3 394 0.0762 3.59 4.93 13.9 0.152 7.19 1.00 4.93
CHS C
25 H 2.93 0.106 36.1 8.43 373 0.0419 2.49 3.55 10.6 0.0838 4.97 1.00 3.55
33.7 4.0 C
x CHS
3.2 25 M 2.41 0.106 44.0 10.5 307 0.0360 2.14 2.99 10.8 0.0721 4.28 1.00 2.99
CHS C
20 XH 2.26 0.0845 37.4 6.73 288 0.0194 1.45 2.12 8.22 0.0389 2.89 1.00 2.12
26.9 4.0 C
x CHS
3.2 20 H 1.87 0.0845 45.2 8.41 238 0.0170 1.27 1.81 8.46 0.0341 2.53 1.00 1.81
CHS C
2.6 20 M 1.56 0.0845 54.2 10.3 198 0.0148 1.10 1.54 8.64 0.0296 2.20 1.00 1.54
CHS C
15 H 1.43 0.0669 46.8 6.66 182 0.00768 0.722 1.06 6.50 0.0154 1.44 1.00 1.06
21.3 3.2 C
x CHS
2.6 15 M 1.20 0.0669 55.8 8.19 153 0.00681 0.639 0.915 6.68 0.0136 1.28 1.00 0.915
CHS C
do
t
Smorgon Steel Tube Mills A.B.N. 22 010 469 977. PO Box 246 Sunnybank, Queensland 4109 Australia Telephone +61 7 3246 2600 Facsimile +61 7 3246 2660 E-mail tubemills@smorgonsteel.com.au Internet www.smorgonsteel.com.au/tubemills
DECEMBER 2006 2-5
PART 0 PART 9
PART 1 PART 2 PART 3 PART 4 PART 5 PART 6 PART 7 PART 8
Quick Reference Product Material Safety
General Information Structural Products Piping Products Other Products Steel Grades Mill Finishes Mill Processing Fabrication
Availability Guide Data Sheets (MSDS)
Blank Page
Smorgon Steel Tube Mills A.B.N. 22 010 469 977. PO Box 246 Sunnybank, Queensland 4109 Australia Telephone +61 7 3246 2600 Facsimile +61 7 3246 2660 E-mail tubemills@smorgonsteel.com.au Internet www.smorgonsteel.com.au/tubemills
DECEMBER 2006 2-6
Structural CHS C250L0 ā? Mass & Bundling calculated in accordance with AS 1163
Dimensions Bundling Mass
KleenKoteĀ® HotDipGal
Bundle Dimensions (mm)
Designation Nominal
Lengths Per Bundle Metres Per Bundle Mass Per Bundle Mass Per Bundle
Nominal Nominal
Size
Mass Mass
6.5 8.0 9.0 12.0
dO t tonnes tonnes
1 1
CHS CHS
6.5 8.0 9.0 12.0 6.5 8.0 9.0 12.0 kg/m 6.5 8.0 9.0 12.0 kg/m 6.5 8.0 9.0 12.0
mm mm DN Wx H WxH WxH WxH m/t m/t
2 2
C250L0 C250L0
15 M 362 316 217 1410.5 1.20 834 1.69 1.23 810 1.74
21.3 2.6 - - - - - - - - - - - - - - -
x CHS 3 3
KleenKoteĀ® HotDipGal
3.2 15 H 362 316 217 1410.5 1.43 700 2.01 1.46 684 2.06
CHS - - - - - - - - - - - - - - -
20 M 350 306 127 825.5 1.56 642 1.29 1.60 624 1.32
26.9 2.6 - - - - - - - - - - - - - - -
x CHS
3.2 20 H 350 306 127 825.5 1.87 535 1.54 1.92 522 1.58
CHS - - - - - - - - - - - - - - - Notes:
4.0 20 XH 350 306 127 825.5 2.26 443 1.86 2.30 434 1.90
CHS - - - - - - - - - - - - - - - 1. Swaged end/s are available on sizes 33.7 mm ā? 60.3 mm.
25 M 371 326 91 591.5 2.41 415 1.42 2.46 406 1.46
33.7 3.2 - - - - - - - - - - - - - - -
x CHS
2. Grade C250L0: M = Medium; H = Heavy; XH = Extra Heavy.
4.0 25 H 371 326 91 591.5 2.93 341 1.73 2.99 335 1.77
CHS - - - - - - - - - - - - - - -
3. LiteOil and NoKote are available in all sections on request.
32 M 382 336 61 396.5 3.09 323 1.23 3.17 316 1.26
42.4 3.2 - - - - - - - - - - - - - - -
x CHS
4. Refer to Piping Products for Pipe in Grade C250L0
4.0 32 H 382 336 61 396.5 3.79 264 1.50 3.86 259 1.53
CHS - - - - - - - - - - - - - - -
meeting AS 1074.
40 M 435 383 61 396.5 3.56 281 1.41 3.64 274 1.45
48.3 3.2 - - - - - - - - - - - - - - -
x CHS
4.0 40 H 435 383 61 396.5 4.37 229 1.73 4.45 225 1.77
CHS - - - - - - - - - - - - - - -
50 M 422 374 37 240.5 5.03 199 1.21 5.14 195 1.24
60.3 3.6 - - - - - - - - - - - - - - -
x CHS
4.5 50 H 422 374 37 240.5 6.19 161 1.49 6.30 159 1.51
CHS - - - - - - - - - - - - - - -
5.4 50 XH 422 374 37 240.5 7.31 137 1.76 7.41 135 1.78
CHS - - - - - - - - - - - - - - -
65 M 533 472 37 240.5 6.44 155 1.55 6.57 152 1.58
76.1 3.6 - - - - - - - - - - - - - - -
x CHS
4.5 65 H 533 472 37 240.5 7.95 126 1.91 8.08 124 1.94
CHS - - - - - - - - - - - - - - -
5.9 65 XH 533 472 37 240.5 10.2 97.9 2.46 10.3 96.7 2.49
CHS - - - - - - - - - - - - - - -
80 M 445 397 19 123.5 8.38 119 1.03 8.54 117 1.05
88.9 4.0 - - - - - - - - - - - - - - -
x CHS
5.0 80 H 445 397 19 123.5 10.3 96.7 1.28 10.5 95.2 1.30
CHS - - - - - - - - - - - - - - -
5.9 80 XH 445 397 19 123.5 12.1 82.8 1.49 12.2 81.7 1.51
CHS - - - - - - - - - - - - - - -
90 M 508 454 19 123.5 9.63 104 1.19 9.81 102 1.21
101.6 4.0 - - - - - - - - - - - - - - -
x CHS
5.0 90 H 508 454 19 123.5 11.9 84.0 1.47 12.1 82.7 1.49
CHS - - - - - - - - - - - - - - -
100 M 572 510 19 123.5 12.2 82.1 1.50 12.4 80.7 1.53
114.3 4.5 - - - - - - - - - - - - - - -
x CHS
5.4 100 H 572 510 19 123.5 14.5 69.0 1.79 14.7 68.0 1.82
CHS - - - - - - - - - - - - - - -
125 M 699 382 13 84.5 16.6 60.2 1.40 16.9 59.3 1.43
139.7 5.0 - - - - - - - - - - - - - - -
x CHS
5.4 125 H 699 382 13 84.5 17.9 55.9 1.51 18.1 55.1 1.53
CHS - - - - - - - - - - - - - - -
150 M 660 451 10 65 19.7 50.7 1.28 20.0 49.9 1.30
165.1 5.0 - - - - - - - - - - - - - - -
x CHS
5.4 150 H 660 451 10 65 21.3 47.0 1.38 21.6 46.4 1.40
CHS - - - - - - - - - - - - - - - do
t
Smorgon Steel Tube Mills A.B.N. 22 010 469 977. PO Box 246 Sunnybank, Queensland 4109 Australia Telephone +61 7 3246 2600 Facsimile +61 7 3246 2660 E-mail tubemills@smorgonsteel.com.au Internet www.smorgonsteel.com.au/tubemills
DECEMBER 2006 2-7
PART 0 PART 9
PART 1 PART 2 PART 3 PART 4 PART 5 PART 6 PART 7 PART 8
Quick Reference Product Material Safety
General Information Structural Products Piping Products Other Products Steel Grades Mill Finishes Mill Processing Fabrication
Availability Guide Data Sheets (MSDS)
Blank Page
Smorgon Steel Tube Mills A.B.N. 22 010 469 977. PO Box 246 Sunnybank, Queensland 4109 Australia Telephone +61 7 3246 2600 Facsimile +61 7 3246 2660 E-mail tubemills@smorgonsteel.com.au Internet www.smorgonsteel.com.au/tubemills
DECEMBER 2006 2-8
Structural CHS C350L0 ā? Specifications
Technical Specifications Standard Lengths
This primer paint finish is applied in-line using the
patented KleenKoteĀ® process and is supplied in the
Australian Standards Standard length for Structural CHS Grade C350L0:
following coating thicknesses:
(26.9 OD ā? 165.1 OD CHS)
Structural CHS Grade C350L0 is manufactured Black ______________________Target 12 microns with
SupaGalĀ®/KleenKoteĀ®/HotDipGal ___________ 6.5 m
_
and tested to comply with the requirements of the ________________________ average at 8-10 microns (168.3 OD ā? 508.0 OD CHS) LiteOil _________ 12.0 m
following specifications: 1
1 1 1 CHS
CHS CHS CHS
Note: Non-standard finishes, such as NoKote, are May exclude some wall thicknesses and finishes. 2
2 2 2 C350L0
C350L0 C350L0 C350L0
AS 1163 ā? Structural steel hollow sections
available if ordered prior to rollings. Conditions apply. Contact your Smorgon Steel Tube Mills representative
(Grade C350L0). 3
3 3 3 LiteOil
SupaGalĀ® KleenKoteĀ® HotDipGal
Refer to manufacturer for details. for further details.
AS/NZS 4792 ā? Hot-dip galvanized (zinc) coatings
See Quick Reference Product Availability Guide (Part 0)
on ferrous hollow sections, applied by a continuous Non-Standard Lengths
for further information on availability.
or a specialized process (Section 2 or Section 3).
General Description
Special orders of non-standard pack lengths of
Mechanical Properties HotDipGal Finish Structural CHS Grade C350L0 are available (conditions Manufacturing Process
apply). Check with your distributor for details.
Structural CHS Grade C350L0 has the following Galvanized (Hot-dip)
Structural CHS Grade C350L0, for general structural
mechanical properties:
Minimum Length:
Structural CHS Grade C350L0 with HotDipGal finish and mechanical applications, is manufactured by
350 MPa
Minimum Yield Strength __________________ 4.2 m
Ā® ___________
is manufactured and tested to meet the requirements (26.9 OD ā? 114.3 OD) KleenKote
cold-forming and high frequency Electric Resistance
Minimum Tensile Strength _______________ 430 MPa
_ (139.7 OD ā? 165.1 OD) KleenKoteĀ® __________ 5.3 m
of Section 2 of AS/NZS 4792.
Welding (ERW) of high strength steel strip. The cold-
Minimum Elongation in 5.65āSo _______________ 20%
(26.9 OD ā? 114.3 OD) SupaGalĀ® ____________ 4.2 m
Minimum coating mass _________ 300 g/m2 each side forming process enhances the strength, hardness
L0 __ guaranteed impact properties at 0Ā°C to AS 1163
_
(26.9 OD ā? 114.3 OD) HotDipGal ____________ 5.0 m
The coating adherence of the galvanizing is satisfactory for and surface finish of the pipe and produces product
Tolerances (139.7 OD ā? 165.1 OD) HotDipGal ___________ 5.3 m
the CHS to be bent to a radius 6 times the diameter of the to tight dimensional tolerances.
Tolerances for Structural CHS Grade C350L0 are CHS up to 60.3 mm OD in accordance with AS/NZS 4792. Maximum Length:
Further Information
compliant with AS 1163. See Dimensional Tolerances (26.9 OD ā? 48.3 OD) KleenKoteĀ® ____________ 8.0 m
See Quick Reference Product Availability Guide (Part 0)
in Part 1 for more information. for further information on availability. (60.3 OD ā? 114.3 OD) KleenKoteĀ® __________ 12.0 m For further information refer to the Smorgon Steel Tube Mills:
Supply Conditions (88.9 OD ā? 165.1 OD) KleenKoteĀ® __________ 13.0 m
LiteOil Finish Product Solutions Guide.
(26.9 OD ā? 114.3 OD) SupaGalĀ® ____________ 7.2 m
SupaGalĀ® Finish LiteOil tubular products use a light oil coating and is the (26.9 OD ā? 114.3 OD) HotDipGal ____________ 7.2 m
Structural CHS Grade C350L0 with SupaGalĀ® finish standard finish for medium to large sized CHS. (139.7 OD ā? 165.1 OD) HotDipGal __________ 12.2 m
is manufactured using steel strip that has the following
See Quick Reference Product Availability Guide (Part 0) Note: Contact your Smorgon Steel Tube Mills
coating thickness:
for further information on availability. representative for lengths outside this range.
Minimum coating mass ________ 100 g/m2 each side
End Finish (Mill Processing) Thickness
Designated as __________ AS/NZS 4792 ZB 100/100
See Quick Reference Product Availability Guide (Part 0) Up to and including 168.3 x 6.0 CHS: Structural CHS Grade C350L0 are available in 2.0 mm to
for further information on availability.
16.0 mm wall thickness. Sections with 165.1 mm OD and
Plain Ends as standard and Screwed Ends optional.
KleenKoteĀ® Finish less are identified by the following end colour codes:
Above this size, Bevelled Ends as standard.
Extra Light ______________________________ Green
Please refer to Mill Processing (Part 7) of this
Structural CHS Grade C350L0 with KleenKoteĀ®
Product Manual for end finish availability.
finish is supplied in the following surface colour: Light ___________________________________ Yellow
Otherwise no end colour coding applies.
Black
Smorgon Steel Tube Mills A.B.N. 22 010 469 977. PO Box 246 Sunnybank, Queensland 4109 Australia Telephone +61 7 3246 2600 Facsimile +61 7 3246 2660 E-mail tubemills@smorgonsteel.com.au Internet www.smorgonsteel.com.au/tubemills
DECEMBER 2006 2-9
PART 0 PART 9
PART 1 PART 2 PART 3 PART 4 PART 5 PART 6 PART 7 PART 8
Quick Reference Product Material Safety
General Information Structural Products Piping Products Other Products Steel Grades Mill Finishes Mill Processing Fabrication
Availability Guide Data Sheets (MSDS)
Blank Page
Smorgon Steel Tube Mills A.B.N. 22 010 469 977. PO Box 246 Sunnybank, Queensland 4109 Australia Telephone +61 7 3246 2600 Facsimile +61 7 3246 2660 E-mail tubemills@smorgonsteel.com.au Internet www.smorgonsteel.com.au/tubemills
DECEMBER 2006 2-10
Structural CHS C350L0 ā? Section Properties calculated to AS 1163 in accordance with AS 4100
Properties for Design to AS 4100
Dimensions and Ratios Properties
External Gross Torsion Torsion
Designation About any axis Form Factor About any axis
Nominal Mass Surface Area Section Area Constant Modulus
do
Size per m
do t per m per t Ag I Z S r J C kf Compactness Ze
t
10 6 mm4 10 3 mm 3 10 3 mm 3 10 6 mm4 10 3 mm 3 10 3 mm 3
m 2 /m m 2 /t mm 2
mm mm DN kg/m mm (C,N,S)
1
1 1 1 CHS
CHS CHS CHS
194 1.60 8.22 31.8 24700 749 2950 3870 174 1500 5900 1.00 3870
508.0 16.0 - C
x CHS 2
2 2 2 C350L0
C350L0 C350L0 C350L0
12.5 153 1.60 10.4 40.6 19500 598 2350 3070 175 1200 4710 1.00 3000
CHS - N 3
3 3 3 LiteOil
SupaGalĀ® KleenKoteĀ® HotDipGal
10.0 123 1.60 13.0 50.8 15600 485 1910 2480 176 970 3820 1.00 2310
CHS - N
174 1.44 8.25 28.6 22200 540 2360 3110 156 1080 4720 1.00 3110
457.0 16.0 - C
x CHS
12.5 137 1.44 10.5 36.6 17500 431 1890 2470 157 863 3780 1.00 2460
CHS - N Notes:
10.0 110 1.44 13.0 45.7 14000 351 1540 2000 158 702 3070 1.00 1910
CHS - N 1. For Grade C350L0: fy = 350 MPa and fu = 430 MPa;
154 1.28 8.29 25.4 19600 374 1840 2440 138 749 3690 1.00 2440
406.4 16.0 - C
x CHS fy = yield stress used in design; fu = tensile strength
12.5 121 1.28 10.5 32.5 15500 300 1480 1940 139 601 2960 1.00 1940
CHS - C used in design; as defined in AS 4100.
10.0 97.8 1.28 13.1 40.6 12500 245 1200 1570 140 490 2410 1.00 1530
CHS - N 2. C = Compact Section; N = Non-Compact Section;
8.0 78.6 1.28 16.2 50.8 10000 199 978 1270 141 397 1960 1.00 1180
CHS - N S = Slender Section (as defined in AS 4100).
134 1.12 8.34 22.2 17100 247 1390 1850 120 493 2770 1.00 1850
355.6 16.0 - C
x CHS 3. Grade C350L0 to AS 1163 is cold-formed and is therefore
12.5 106 1.12 10.6 28.4 13500 199 1120 1470 121 397 2230 1.00 1470
CHS - C allocated the CF residual stresses classification in AS 4100.
10.0 85.2 1.12 13.1 35.6 10900 162 912 1190 122 324 1820 1.00 1190
CHS - C 4. Grade C350L0: XL = Extra Light; L = Light.
8.0 68.6 1.12 16.3 44.5 8740 132 742 967 123 264 1480 1.00 928
CHS - N 5. LiteOil and NoKote are available in all sections on request.
96.0 1.02 10.6 25.9 12200 148 917 1210 110 297 1830 1.00 1210
323.9 12.5 - C
x CHS
10.0 77.4 1.02 13.1 32.4 9860 122 751 986 111 243 1500 1.00 986
CHS - C
8.0 62.3 1.02 16.3 40.5 7940 99.1 612 799 112 198 1220 1.00 781
CHS - N
6.0 47.0 1.02 21.6 54.0 5990 75.7 468 606 112 151 935 1.00 556
CHS - N
80.3 0.858 10.7 21.8 10200 87.1 638 850 92.2 174 1280 1.00 850
273.1 12.5 - C
x CHS
10.0 64.9 0.858 13.2 27.3 8270 71.6 525 693 93.1 143 1050 1.00 693
CHS - C
8.0 52.3 0.858 16.4 34.1 6660 58.6 429 562 93.8 117 858 1.00 562
CHS - C
6.0 39.5 0.858 21.7 45.5 5030 44.9 329 428 94.5 89.8 658 1.00 409
CHS - N
5.0 33.1 0.858 26.0 54.6 4210 37.9 277 359 94.8 75.7 554 1.00 328
CHS - N
63.7 0.688 10.8 17.5 8110 43.4 397 534 73.2 86.9 793 1.00 534
219.1 12.5 - C
x CHS
10.0 51.6 0.688 13.3 21.9 6570 36.0 328 438 74.0 72.0 657 1.00 438
CHS - C
8.0 41.6 0.688 16.5 27.4 5310 29.6 270 357 74.7 59.2 540 1.00 357
CHS - C
6.0 31.5 0.688 21.8 36.5 4020 22.8 208 273 75.4 45.6 417 1.00 272
CHS - N
5.0 26.4 0.688 26.1 43.8 3360 19.3 176 229 75.7 38.6 352 1.00 221
CHS - N
do
t
Smorgon Steel Tube Mills A.B.N. 22 010 469 977. PO Box 246 Sunnybank, Queensland 4109 Australia Telephone +61 7 3246 2600 Facsimile +61 7 3246 2660 E-mail tubemills@smorgonsteel.com.au Internet www.smorgonsteel.com.au/tubemills
DECEMBER 2006 2-11
PART 0 PART 9
PART 1 PART 2 PART 3 PART 4 PART 5 PART 6 PART 7 PART 8
Quick Reference Product Material Safety
General Information Structural Products Piping Products Other Products Steel Grades Mill Finishes Mill Processing Fabrication
Availability Guide Data Sheets (MSDS)
Structural CHS C350L0 ā? Section Properties calculated to AS 1163 in accordance with AS 4100
Properties for Design to AS 4100
Dimensions and Ratios Properties
External Gross Torsion Torsion
Designation About any axis Form Factor About any axis
Nominal Mass Surface Area Section Area Constant Modulus
do
Size per m
do t per m per t Ag I Z S r J C kf Compactness Ze
t
10 6 mm4 10 3 mm 3 10 3 mm 3 10 6 mm4 10 3 mm 3 10 3 mm 3
m 2 /m m 2 /t mm 2
mm mm DN kg/m mm (C,N,S)
1
1 1 1 CHS
CHS CHS CHS
45.3 0.609 13.4 19.4 5770 24.4 252 338 65.0 48.8 504 1.00 338
193.7 x 10.0 CHS - C 2
2 2 2 C350L0
C350L0 C350L0 C350L0
8.0 CHS 36.6 0.609 16.6 24.2 4670 20.2 208 276 65.7 40.3 416 1.00 276
- C 3
3 3 3 LiteOil
SupaGalĀ® KleenKoteĀ® HotDipGal
6.0 CHS 27.8 0.609 21.9 32.3 3540 15.6 161 211 66.4 31.2 322 1.00 211
- C
5.0 CHS 23.3 0.609 26.2 38.7 2960 13.2 136 178 66.7 26.4 273 1.00 176
- N
39.0 0.529 13.5 16.8 4970 15.6 186 251 56.1 31.3 372 1.00 251
168.3 x 10.0 CHS - C Notes:
8.0 CHS 31.6 0.529 16.7 21.0 4030 13.0 154 206 56.7 25.9 308 1.00 206
- C 1. For Grade C350L0: fy = 350 MPa and fu = 430 MPa;
6.0 CHS 24.0 0.529 22.0 28.1 3060 10.1 120 158 57.4 20.2 240 1.00 158
- C fy = yield stress used in design; fu = tensile strength
5.0 CHS 20.1 0.529 26.3 33.7 2570 8.56 102 133 57.8 17.1 203 1.00 133
- C used in design; as defined in AS 4100.
4.0 CHS 16.2 0.529 32.6 42.1 2060 6.97 82.8 108 58.1 13.9 166 1.00 105
- N 2. C = Compact Section; N = Non-Compact Section;
150 L 13.9 0.519 37.2 47.2 1780 5.80 70.3 91.4 57.1 11.6 141 1.00 86.6
165.1 x 3.5 CHS N S = Slender Section (as defined in AS 4100).
3.0 CHS 150 XL 12.0 0.519 43.2 55.0 1530 5.02 60.8 78.8 57.3 10.0 122 1.00 71.9
N 3. Grade C350L0 to AS 1163 is cold-formed and is therefore allocated
125 L 11.8 0.439 37.3 39.9 1500 3.47 49.7 64.9 48.2 6.95 99.5 1.00 63.7
139.7 x 3.5 CHS N the CF residual stresses classification in AS 4100.
3.0 CHS 125 XL 10.1 0.439 43.4 46.6 1290 3.01 43.1 56.1 48.3 6.02 86.2 1.00 53.3
N 4. Grade C350L0: XL = Extra Light; L = Light.
100 L 9.83 0.359 36.5 31.8 1250 1.92 33.6 44.1 39.2 3.84 67.2 1.00 44.1
114.3 x 3.6 CHS C 5. LiteOil and NoKote are available in all sections on request.
3.2 CHS 100 XL 8.77 0.359 41.0 35.7 1120 1.72 30.2 39.5 39.3 3.45 60.4 1.00 39.5
N
90 L 7.77 0.319 41.1 31.8 989 1.20 23.6 31.0 34.8 2.40 47.2 1.00 31.0
101.6 x 3.2 CHS C
2.6 CHS 90 XL 6.35 0.319 50.3 39.1 809 0.991 19.5 25.5 35.0 1.98 39.0 1.00 25.1
N
80 L 6.76 0.279 41.3 27.8 862 0.792 17.8 23.5 30.3 1.58 35.6 1.00 23.5
88.9 x 3.2 CHS C
2.6 CHS 80 XL 5.53 0.279 50.5 34.2 705 0.657 14.8 19.4 30.5 1.31 29.6 1.00 19.4
C
65 L 5.75 0.239 41.6 23.8 733 0.488 12.8 17.0 25.8 0.976 25.6 1.00 17.0
76.1 x 3.2 CHS C
2.3 CHS 65 XL 4.19 0.239 57.1 33.1 533 0.363 9.55 12.5 26.1 0.727 19.1 1.00 12.5
C
50 L 4.11 0.189 46.1 20.8 523 0.216 7.16 9.56 20.3 0.432 14.3 1.00 9.56
60.3 x 2.9 CHS C
2.3 CHS 50 XL 3.29 0.189 57.6 26.2 419 0.177 5.85 7.74 20.5 0.353 11.7 1.00 7.74
C
40 L 3.25 0.152 46.7 16.7 414 0.107 4.43 5.99 16.1 0.214 8.86 1.00 5.99
48.3 x 2.9 CHS C
2.3 CHS 40 XL 2.61 0.152 58.2 21.0 332 0.0881 3.65 4.87 16.3 0.176 7.30 1.00 4.87
C
32 L 2.55 0.133 52.2 16.3 325 0.0646 3.05 4.12 14.1 0.129 6.10 1.00 4.12
42.4 x 2.6 CHS C
2.0 CHS 32 XL 1.99 0.133 66.8 21.2 254 0.0519 2.45 3.27 14.3 0.104 4.90 1.00 3.27
C
25 L 1.99 0.106 53.1 13.0 254 0.0309 1.84 2.52 11.0 0.0619 3.67 1.00 2.52
33.7 x 2.6 CHS C
2.0 CHS 25 XL 1.56 0.106 67.7 16.9 199 0.0251 1.49 2.01 11.2 0.0502 2.98 1.00 2.01
C do
20 L 1.40 0.0845 60.6 11.7 178 0.0136 1.01 1.40 8.74 0.0271 2.02 1.00 1.40
26.9 x 2.3 CHS C
2.0 CHS 20 XL 1.23 0.0845 68.8 13.5 156 0.0122 0.907 1.24 8.83 0.0244 1.81 1.00 1.24
C
t
Smorgon Steel Tube Mills A.B.N. 22 010 469 977. PO Box 246 Sunnybank, Queensland 4109 Australia Telephone +61 7 3246 2600 Facsimile +61 7 3246 2660 E-mail tubemills@smorgonsteel.com.au Internet www.smorgonsteel.com.au/tubemills
DECEMBER 2006 2-12
Structural CHS C350L0 ā? Mass & Bundling calculated in accordance with AS 1163
Dimensions Bundling Mass
SupaGalĀ®/KleenKoteĀ®/LiteOil HotDipGal
Bundle Dimensions (mm)
Designation Nominal
Lengths Per Bundle Metres Per Bundle Mass Per Bundle Mass Per Bundle
Nominal Nominal
Size
Mass Mass
6.5 8.0 9.0 12.0
dO t tonnes tonnes
1
1 1 1 CHS
CHS CHS CHS
6.5 8.0 9.0 12.0 6.5 8.0 9.0 12.0 kg/m 6.5 8.0 9.0 12.0 6.5 8.0 9.0 12.0
mm mm DN Wx H WxH WxH Wx H m/t kg/m m/t
2
2 2 2 C350L0
C350L0 C350L0 C350L0
20 XL 350 306 127 825.5 1.23 814 1.01 1.28 784 1.05
26.9 2.0 - - - - - - - - - - - - - - -
x CHS 3
3 3 3 LiteOil
SupaGalĀ® KleenKoteĀ® HotDipGal
2.3 20 L 350 306 127 825.5 1.40 717 1.15 1.44 694 1.19
CHS - - - - - - - - - - - - - - -
25 XL 371 326 91 591.5 1.56 640 0.925 1.62 616 0.960
33.7 2.0 - - - - - - - - - - - - - - -
x CHS
2.6 25 L 371 326 91 591.5 1.99 501 1.18 2.05 487 1.21
CHS - - - - - - - - - - - - - - - Notes:
32 XL 382 336 61 396.5 1.99 502 0.790 2.07 483 0.820
42.4 2.0 - - - - - - - - - - - - - - -
x CHS 1. Swaged end/s are available on sizes 33.7 mm ā? 60.3 mm.
2.6 32 L 382 336 61 396.5 2.55 392 1.01 2.63 381 1.04
CHS - - - - - - - - - - - - - - -
2. Grade C350L0: XL = Extra Light; L = Light.
40 XL 435 383 61 396.5 2.61 383 1.03 2.70 371 1.07
48.3 2.3 - - - - - - - - - - - - - - -
x CHS
3. LiteOil and NoKote are available in all sections on request.
2.9 40 L 435 383 61 396.5 3.25 308 1.29 3.33 300 1.32
CHS - - - - - - - - - - - - - - -
50 XL 422 374 37 240.5 3.29 304 0.791 3.40 294 0.818
60.3 2.3 - - - - - - - - - - - - - - -
x CHS
2.9 50 L 422 374 37 240.5 4.11 244 0.987 4.21 237 1.01
CHS - - - - - - - - - - - - - - -
65 XL 533 472 37 240.5 4.19 239 1.01 4.33 231 1.04
76.1 2.3 - - - - - - - - - - - - - - -
x CHS
3.2 65 L 533 472 37 240.5 5.75 174 1.38 5.89 170 1.42
CHS - - - - - - - - - - - - - - -
80 XL 445 397 19 123.5 5.53 181 0.683 5.70 176 0.703
88.9 2.6 - - - - - - - - - - - - - - -
x CHS
3.2 80 L 445 397 19 123.5 6.76 148 0.835 6.92 144 0.855
CHS - - - - - - - - - - - - - - -
90 XL 508 454 19 123.5 6.35 158 0.784 6.53 153 0.807
101.6 2.6 - - - - - - - - - - - - - - -
x CHS
3.2 90 L 508 454 19 123.5 7.77 129 0.959 7.95 126 0.982
CHS - - - - - - - - - - - - - - -
100 XL 572 510 19 123.5 8.77 114 1.08 8.98 111 1.11
114.3 3.2 - - - - - - - - - - - - - - -
x CHS
3.6 100 L 572 510 19 123.5 9.83 102 1.21 10.0 99.6 1.24
CHS - - - - - - - - - - - - - - -
125 XL 699 382 13 84.5 10.1 98.9 0.855 10.4 96.4 0.876
139.7 3.0 - - - - - - - - - - - - - - -
x CHS
3.5 125 L 699 382 13 84.5 11.8 85.1 0.993 12.0 83.2 1.02
CHS - - - - - - - - - - - - - - -
150 XL 660 451 10 65 12.0 83.4 0.780 12.3 81.3 0.799
165.1 3.0 - - - - - - - - - - - - - - -
x CHS
3.5 150 L 660 451 10 65 13.9 71.7 0.907 14.3 70.2 0.926
CHS - - - - - - - - - - - - - - -
505 460 7 84 16.2 61.7 - 1.36 - - -
168.3 4.0 - - - - - - - - - - - - - - -
x CHS
5.0 505 460 7 84 20.1 49.7 - 1.69 - - -
CHS - - - - - - - - - - - - - - -
6.0 337 314 3 36 24.0 41.6 - 0.865 - - -
CHS - - - - - - - - - - - - - - -
8.0 337 314 3 36 31.6 31.6 - 1.14 - - -
CHS - - - - - - - - - - - - - - -
10.0 337 314 3 36 39.0 25.6 - 1.41 - - -
CHS - - - - - - - - - - - - - - -
387 361 3 36 23.3 43.0 - 0.838 - - -
193.7 5.0 - - - - - - - - - - - - - - -
x CHS do
6.0 387 361 3 36 27.8 36.0 - 1.00 - - -
CHS - - - - - - - - - - - - - - -
8.0 387 361 3 36 36.6 27.3 - 1.32 - - -
CHS - - - - - - - - - - - - - - -
10.0 387 361 3 36 45.3 22.1 - 1.63 - - - t
CHS - - - - - - - - - - - - - - -
Smorgon Steel Tube Mills A.B.N. 22 010 469 977. PO Box 246 Sunnybank, Queensland 4109 Australia Telephone +61 7 3246 2600 Facsimile +61 7 3246 2660 E-mail tubemills@smorgonsteel.com.au Internet www.smorgonsteel.com.au/tubemills
DECEMBER 2006 2-13
PART 0 PART 9
PART 1 PART 2 PART 3 PART 4 PART 5 PART 6 PART 7 PART 8
Quick Reference Product Material Safety
General Information Structural Products Piping Products Other Products Steel Grades Mill Finishes Mill Processing Fabrication
Availability Guide Data Sheets (MSDS)
Structural CHS C350L0 ā? Mass & Bundling calculated in accordance with AS 1163
Dimensions Bundling Mass
SupaGalĀ®/KleenKoteĀ®/LiteOil HotDipGal
Bundle Dimensions (mm)
Designation Nominal
Lengths Per Bundle Metres Per Bundle Mass Per Bundle Mass Per Bundle
Nominal
Size Nominal Mass
Mass
6.5 8.0 9.0 12.0
dO t tonnes tonnes
1
1 1 1 CHS
CHS CHS CHS
6.5 8.0 9.0 12.0 6.5 8.0 9.0 12.0 6.5 8.0 9.0 12.0 6.5 8.0 9.0 12.0
mm mm DN WxH WxH WxH W x H kg/m m/t kg/m m/t
2
2 2 2 C350L0
C350L0 C350L0 C350L0
438 409 3 36 26.4 37.9 0.950 - - - - - -
219.1 5.0 - - - - - - - - - - - - -
x CHS 3
3 3 3 LiteOil
SupaGalĀ® KleenKoteĀ® HotDipGal
6.0 438 409 3 36 31.5 31.7 1.14 - - - - - -
CHS - - - - - - - - - - - - -
8.0 438 409 3 36 41.6 24.0 1.50 - - - - - -
CHS - - - - - - - - - - - - -
10.0 219 219 1 12 51.6 19.4 0.619 - - - - - -
CHS - - - - - - - - - - - - - Notes:
12.5 219 219 1 12 63.7 15.7 0.764 - - - - - -
CHS - - - - - - - - - - - - - 1. Swaged end/s are available on sizes 33.7 mm ā? 60.3 mm.
546 510 3 36 33.1 30.2 1.19 - - - - - -
273.1 5.0 - - - - - - - - - - - - -
x CHS
2. Grade C350L0: XL = Extra Light; L = Light.
6.0 546 510 3 36 39.5 25.3 1.42 - - - - - -
CHS - - - - - - - - - - - - -
3. LiteOil and NoKote are available in all sections on request.
8.0 546 510 3 36 52.3 19.1 1.88 - - - - - -
CHS - - - - - - - - - - - - -
10.0 273 273 1 12 64.9 15.4 0.779 - - - - - -
CHS - - - - - - - - - - - - -
12.5 273 273 1 12 80.3 12.4 0.964 - - - - - -
CHS - - - - - - - - - - - - -
648 604 3 36 47.0 21.3 1.69 - - - - - -
323.9 6.0 - - - - - - - - - - - - -
x CHS
8.0 324 324 1 12 62.3 16.0 0.748 - - - - - -
CHS - - - - - - - - - - - - -
10.0 324 324 1 12 77.4 12.9 0.929 - - - - - -
CHS - - - - - - - - - - - - -
12.5 324 324 1 12 96.0 10.4 1.15 - - - - - -
CHS - - - - - - - - - - - - -
356 356 1 12 68.6 14.6 0.823 - - - - - -
355.6 8.0 - - - - - - - - - - - - -
x CHS
10.0 356 356 1 12 85.2 11.7 1.02 - - - - - -
CHS - - - - - - - - - - - - -
12.5 356 356 1 12 106 9.45 1.27 - - - - - -
CHS - - - - - - - - - - - - -
16.0 356 356 1 12 134 7.46 1.61 - - - - - -
CHS - - - - - - - - - - - - -
406 406 1 12 78.6 12.7 0.943 - - - - - -
406.4 8.0 - - - - - - - - - - - - -
x CHS
10.0 406 406 1 12 97.8 10.2 1.17 - - - - - -
CHS - - - - - - - - - - - - -
12.5 406 406 1 12 121 8.24 1.46 - - - - - -
CHS - - - - - - - - - - - - -
16.0 406 406 1 12 154 6.49 1.85 - - - - - -
CHS - - - - - - - - - - - - -
457 457 1 12 110 9.07 1.32 - - - - - -
457.0 10.0 - - - - - - - - - - - - -
x CHS
12.5 457 457 1 12 137 7.30 1.64 - - - - - -
CHS - - - - - - - - - - - - -
16.0 457 457 1 12 174 5.75 2.09 - - - - - -
CHS - - - - - - - - - - - - -
508 508 1 12 123 8.14 1.47 - - - - - -
508.0 10.0 - - - - - - - - - - - - -
x CHS
12.5 508 508 1 12 153 6.55 1.83 - - - - - -
CHS - - - - - - - - - - - - -
16.0 508 508 1 12 194 5.15 2.33 - - - - - -
CHS - - - - - - - - - - - - - do
t
Smorgon Steel Tube Mills A.B.N. 22 010 469 977. PO Box 246 Sunnybank, Queensland 4109 Australia Telephone +61 7 3246 2600 Facsimile +61 7 3246 2660 E-mail tubemills@smorgonsteel.com.au Internet www.smorgonsteel.com.au/tubemills
DECEMBER 2006 2-14
Structural RHS DualGradeĀ® ā? Specifications
Technical Specifications See Quick Reference Product Availability Guide (Part 0) Contact your Smorgon Steel Tube Mills representative
for further details.
for further information on availability.
Australian Standards
Non-Standard Lengths
KleenKoteĀ® Finish
Structural RHS DualGradeĀ® C350L0/C450L0
Special orders of non-standard pack lengths of Structural
Structural RHS DualGradeĀ® C350L0/C450L0
is manufactured and tested to comply with the
RHS DualGradeĀ® C350L0/C450L0 are available (conditions 1
1 1
with KleenKoteĀ® finish is supplied in the following RHS RHS RHS
requirements of the following specifications:
2
2 2
DualGradeĀ® DualGradeĀ® DualGradeĀ®
apply). Check with your distributor for details.
surface colours: 3
AS 1163 ā? Structural steel hollow sections 3 3
SupaGalĀ® KleenKoteĀ® LiteOil
Minimum Length:
(Grade C350L0 and Grade C450L0). Blue Black
(50x25 ā? 150x50 RHS) SupaGalĀ®/KleenKoteĀ® __4.2 m
This primer paint finish is applied in-line using the
AS/NZS 4792 ā? Hot-dip galvanized (zinc) coatings
General Description
on ferrous hollow sections, applied by a continuous patented KleenKoteĀ® process and is supplied in the Maximum Length:
or a specialized process (Section 3). following coating thicknesses: (50x25 RHS) SupaGalĀ®/KleenKoteĀ® __________ 8.0 m Manufacturing Process
Mechanical Properties Blue & Black _______________ Target 12 microns with (65x35 ā? 150x50 RHS) SupaGalĀ®/KleenKoteĀ® 12.2 m
_
Structural RHS DualGradeĀ® C350L0/C450L0, for general
________________________ average at 8-10 microns Note: Contact your Smorgon Steel Tube Mills
Structural RHS DualGradeĀ® C350L0/C450L0 has the fabrication and structural applications, is manufactured
Note: Non-standard finishes, such as NoKote, are representative for lengths outside this range.
following mechanical properties: by cold-forming and high frequency Electric Resistance
available if ordered prior to rollings. Conditions apply.
Welding (ERW) of high strength steel strip. The cold-
Thickness
450 MPa
Minimum Yield Strength _________________
Refer to manufacturer for details.
forming process enhances the strength, hardness and
500 MPa
Minimum Tensile Strength ______________
_
Structural RHS DualGradeĀ® C350L0/C450L0 is available in
See Quick Reference Product Availability Guide (Part 0) surface finish of the tube and produces product to tight
Minimum Elongation in 5.65āSo ______________ 16% 1.6 mm to 16.0 mm wall thicknesses. These thicknesses
for further information on availability. dimensional tolerances.
L0 __ guaranteed impact properties at 0Ā°C to AS 1163
_ are identified by the following end colour codes:
LiteOil Finish Further Information
Note: Although the minimum elongation is 16%, in-house _________________________________ Purple
1.6 mm
testing indicates the typical elongation is approximately 22%. LiteOil tubular products use a light oil coating which For further information refer to the Smorgon Steel Tube Mills:
_________________________________ Brown
1.8 mm
is the standard finish for medium to large sized RHS.
Tolerances _________________________________ Yellow Product Solutions Guide.
2.0 mm
See Quick Reference Product Availability Guide (Part 0) ___________________________________ Pink
2.5 mm
Tolerances for Structural RHS DualGradeĀ®
for further information on availability. ___________________________________ Blue
C350L0/C450L0 are compliant with AS 1163. 3.0 mm
End Finish (Mill Processing) ___________________________________Grey
See Dimensional Tolerances in Part 1 for more information. 3.5 mm
_________________________________ Green
4.0 mm
Supply Conditions Plain Ends only.
________________________________ Orange
5.0 mm
Standard Lengths
SupaGalĀ® Finish _________________________________ Cream
6.0 mm
Standard lengths for Structural RHS DualGradeĀ® ___________________________________ Red
Structural RHS DualGradeĀ® C350L0/C450L0 with 8.0 mm
C350L0/C450L0: _________________________________ Purple
SupaGalĀ® finish is manufactured using steel strip that 9.0 mm
(50x25 ā? 250x150 RHS) SupaGalĀ®/KleenKoteĀ® _ 8.0 m
has the following coating thickness: 10.0 mm _______________________________ Yellow
_
(150x100 ā? 400x300 RHS) KleenKoteĀ®/LiteOil__ 12.0 m
100 g/m2 each side 12.5 mm _________________________________ Blue
_
Minimum coating mass ________
AS/NZS 4792 ZB 100/100 May exclude some wall thicknesses and finishes. 16.0 mm _________________________________Grey
_
Designated as __________
Smorgon Steel Tube Mills A.B.N. 22 010 469 977. PO Box 246 Sunnybank, Queensland 4109 Australia Telephone +61 7 3246 2600 Facsimile +61 7 3246 2660 E-mail tubemills@smorgonsteel.com.au Internet www.smorgonsteel.com.au/tubemills
DECEMBER 2006 2-15
PART 0 PART 9
PART 1 PART 2 PART 3 PART 4 PART 5 PART 6 PART 7 PART 8
Quick Reference Product Material Safety
General Information Structural Products Piping Products Other Products Steel Grades Mill Finishes Mill Processing Fabrication
Availability Guide Data Sheets (MSDS)
Blank Page
Smorgon Steel Tube Mills A.B.N. 22 010 469 977. PO Box 246 Sunnybank, Queensland 4109 Australia Telephone +61 7 3246 2600 Facsimile +61 7 3246 2660 E-mail tubemills@smorgonsteel.com.au Internet www.smorgonsteel.com.au/tubemills
DECEMBER 2006 2-16
Structural RHS DualGradeĀ® ā? Section Properties calculated to AS 1163 in accordance with AS 4100
Properties for Design to AS 4100
Dimensions and Ratios Properties
External Gross
Torsion Torsion Form
Designation Surface Section About x-axis About y-axis About x-axis About y-axis
Mass Constant Modulus Factor
b-2t d-2t
Area Area
per m Compact- Compact-
Ī»e Ī»e
d b t per m per t Ag Ix Zx Sx rx Iy Zy Sy ry J C kf Zex Zey
t t ness ness
1
1 1
RHS RHS RHS
106mm4 103mm3 103mm3 106mm4 103mm3 103mm3 106mm4 103mm3 103mm3 (C,N,S) 103mm3
m2/m m2/t mm2
mm mm mm kg/m mm mm (C,N,S)
2
2 2
DualGradeĀ® DualGradeĀ® DualGradeĀ®
161 1.33 8.27 16.8 23.0 20500 453 2260 2750 149 290 1940 2260 119 586 3170 1.00 22.5 2750 30.9 2230
400 x 300 x 16.0 RHS C N 3
3 3
SupaGalĀ® KleenKoteĀ® LiteOil
12.5 RHS 128 1.35 10.5 22.0 30.0 16300 370 1850 2230 151 238 1590 1830 121 471 2590 0.996 29.5 2230 40.2 1580
C S
10.0 RHS 104 1.36 13.0 28.0 38.0 13300 306 1530 1820 152 197 1320 1500 122 384 2130 0.877 37.6 1600 51.0 1120
N S
8.0 RHS 84.2 1.37 16.2 35.5 48.0 10700 251 1260 1490 153 162 1080 1220 123 312 1750 0.715 47.6 1140 64.4 800
S S Notes:
136 1.13 8.33 10.5 23.0 17300 335 1670 2140 139 113 1130 1320 80.8 290 2000 1.00 14.1 2140 30.9 1300
400 x 200 x 16.0 RHS C N
1. For DualGradeĀ® C350L0/C450L0: fy = 450 MPa
12.5 RHS 109 1.15 10.6 14.0 30.0 13800 277 1380 1740 141 94.0 940 1080 82.4 236 1650 0.996 18.8 1740 40.2 936
C S and fu = 500 MPa; fy = yield stress used in design;
10.0 RHS 88.4 1.16 13.1 18.0 38.0 11300 230 1150 1430 143 78.6 786 888 83.6 194 1370 0.855 24.1 1430 51.0 658
C S fu = tensile strength used in design; as defined in AS 4100
8.0 RHS 71.6 1.17 16.3 23.0 48.0 9120 190 949 1170 144 65.2 652 728 84.5 158 1130 0.745 30.9 1150 64.4 464
N S ā? see Steel Grades (Part 5) of this Product Manual for a
136 1.13 8.33 13.6 19.9 17300 283 1620 1990 128 168 1340 1580 98.5 355 2230 1.00 18.3 1990 26.7 1580
350 x 250 x 16.0 RHS C C definition of DualGradeĀ® C350L0/C450L0.
12.5 RHS 109 1.15 10.6 18.0 26.0 13800 233 1330 1620 130 139 1110 1290 100 287 1840 1.00 24.1 1620 34.9 1200
C N 2. C = Compact Section; N = Non-Compact Section;
S = Slender Section (as defined in AS 4100).
10.0 RHS 88.4 1.16 13.1 23.0 33.0 11300 194 1110 1330 131 116 927 1060 101 235 1520 0.943 30.9 1320 44.3 865
N S
8.0 RHS 71.6 1.17 16.3 29.3 41.8 9120 160 914 1090 132 95.7 766 869 102 191 1250 0.833 39.2 928 56.0 614 3. DualGradeĀ® C350L0/C450L0 designed as Grade C450L0
N S
to AS 1163 is cold-formed, and is therefore allocated the
6.0 RHS 54.4 1.17 21.6 39.7 56.3 6930 124 706 837 134 74.1 593 667 103 146 966 0.622 53.2 611 75.6 399
S S
CF residual stresses classification in AS 4100.
111 0.931 8.42 10.5 16.8 14100 161 1080 1350 107 85.7 857 1020 78.0 193 1450 1.00 14.1 1350 22.5 1020
300 x 200 x 16.0 RHS C C
4. LiteOil and NoKote are available in all sections on request.
12.5 RHS 89.0 0.946 10.6 14.0 22.0 11300 135 899 1110 109 72.0 720 842 79.7 158 1210 1.00 18.8 1110 29.5 842
C C
10.0 RHS 72.7 0.957 13.2 18.0 28.0 9260 113 754 921 111 60.6 606 698 80.9 130 1010 1.00 24.1 921 37.6 628
C N
8.0 RHS 59.1 0.966 16.3 23.0 35.5 7520 93.9 626 757 112 50.4 504 574 81.9 106 838 0.903 30.9 746 47.6 447
N S
6.0 RHS 45.0 0.974 21.7 31.3 48.0 5730 73.0 487 583 113 39.3 393 443 82.8 81.4 651 0.753 42.0 474 64.4 288
S S
85.5 0.731 8.55 7.38 13.6 10900 80.2 641 834 85.8 35.8 478 583 57.3 88.2 836 1.00 9.89 834 18.3 583
250 x 150 x 16.0 RHS C C
12.5 RHS 69.4 0.746 10.8 10.0 18.0 8840 68.5 548 695 88.0 30.8 411 488 59.0 73.4 710 1.00 13.4 695 24.1 488
C C
10.0 RHS 57.0 0.757 13.3 13.0 23.0 7260 58.3 466 582 89.6 26.3 351 409 60.2 61.2 602 1.00 17.4 582 30.9 404
C N
9.0 RHS 51.8 0.761 14.7 14.7 25.8 6600 53.7 430 533 90.2 24.3 324 375 60.7 56.0 554 1.00 19.7 533 34.6 352
C N
8.0 RHS 46.5 0.766 16.5 16.8 29.3 5920 48.9 391 482 90.8 22.2 296 340 61.2 50.5 504 1.00 22.5 482 39.2 299
C N
6.0 RHS 35.6 0.774 21.8 23.0 39.7 4530 38.4 307 374 92.0 17.5 233 264 62.2 39.0 395 0.843 30.9 368 53.2 191
N S
5.0 RHS 29.9 0.779 26.0 28.0 48.0 3810 32.7 262 317 92.6 15.0 199 224 62.6 33.0 337 0.762 37.6 275 64.4 144
N S
b y
t d x x
y
Smorgon Steel Tube Mills A.B.N. 22 010 469 977. PO Box 246 Sunnybank, Queensland 4109 Australia Telephone +61 7 3246 2600 Facsimile +61 7 3246 2660 E-mail tubemills@smorgonsteel.com.au Internet www.smorgonsteel.com.au/tubemills
DECEMBER 2006 2-17
PART 0 PART 9
PART 1 PART 2 PART 3 PART 4 PART 5 PART 6 PART 7 PART 8
Quick Reference Product Material Safety
General Information Structural Products Piping Products Other Products Steel Grades Mill Finishes Mill Processing Fabrication
Availability Guide Data Sheets (MSDS)
Structural RHS DualGradeĀ® ā? Section Properties calculated to AS 1163 in accordance with AS 4100
Properties for Design to AS 4100
Dimensions and Ratios Properties
External Gross
Torsion Torsion Form
Designation Surface Section About x-axis About y-axis About x-axis About y-axis
Mass Constant Modulus Factor
b-2t d-2t
Area Area
per m Compact- Compact-
Ī»e Ī»e
d b t per m per t Ag Ix Zx Sx rx Iy Zy Sy ry J C kf Zex Zey
t t ness ness
1
1 1
RHS RHS RHS
106mm4 103mm3 103mm3 mm 106mm4 103mm3 103mm3 mm 106mm4 103mm3 (C,N,S) 103mm3 (C,N,S) 103mm3
m2/m m2/t mm2
mm mm mm kg/m
2
2 2
DualGradeĀ® DualGradeĀ® DualGradeĀ®
41.3 0.557 13.5 8.00 18.0 5260 24.4 244 318 68.2 8.18 164 195 39.4 21.5 292 1.00 10.7 318 24.1 195
200 x 100 x 10.0 RHS C C 3
3 3
SupaGalĀ® KleenKoteĀ® LiteOil
9.0 RHS 37.7 0.561 14.9 9.11 20.2 4800 22.8 228 293 68.9 7.64 153 180 39.9 19.9 272 1.00 12.2 293 27.1 180
C C
8.0 RHS 33.9 0.566 16.7 10.5 23.0 4320 20.9 209 267 69.5 7.05 141 165 40.4 18.1 250 1.00 14.1 267 30.9 163
C N
6.0 RHS 26.2 0.574 22.0 14.7 31.3 3330 16.7 167 210 70.8 5.69 114 130 41.3 14.2 200 0.967 19.7 210 42.0 110
C S Notes:
5.0 RHS 22.1 0.579 26.2 18.0 38.0 2810 14.4 144 179 71.5 4.92 98.3 111 41.8 12.1 172 0.855 24.1 179 51.0 82.2
C S
1. For DualGradeĀ® C350L0/C450L0: fy = 450 MPa
4.0 RHS 17.9 0.583 32.5 23.0 48.0 2280 11.9 119 147 72.1 4.07 81.5 91.0 42.3 9.89 142 0.745 30.9 144 64.4 58.0
N S and fu = 500 MPa; fy = yield stress used in design;
19.4 0.430 22.2 10.7 23.3 2470 6.91 90.9 116 52.9 2.33 61.4 71.5 30.7 5.98 108 1.00 14.3 116 31.3 70.2
152 x 76 x 6.0 RHS C N fu = tensile strength used in design; as defined in AS 4100
5.0 RHS 16.4 0.435 26.4 13.2 28.4 2090 6.01 79.0 99.8 53.6 2.04 53.7 61.6 31.2 5.13 94.3 1.00 17.7 99.8 38.1 55.2
C N ā? see Steel Grades (Part 5) of this Product Manual for a
33.4 0.457 13.7 8.00 13.0 4260 11.6 155 199 52.2 6.14 123 150 38.0 14.3 211 1.00 10.7 199 17.4 150
150 x 100 x 10.0 RHS C C definition of DualGradeĀ® C350L0/C450L0.
9.0 RHS 30.6 0.461 15.1 9.11 14.7 3900 10.9 145 185 52.9 5.77 115 140 38.5 13.2 197 1.00 12.2 185 19.7 140
C C 2. C = Compact Section; N = Non-Compact Section;
S = Slender Section (as defined in AS 4100).
8.0 RHS 27.7 0.466 16.8 10.5 16.8 3520 10.1 134 169 53.5 5.36 107 128 39.0 12.1 182 1.00 14.1 169 22.5 128
C C
6.0 RHS 21.4 0.474 22.1 14.7 23.0 2730 8.17 109 134 54.7 4.36 87.3 102 40.0 9.51 147 1.00 19.7 134 30.9 101 3. DualGradeĀ® C350L0/C450L0 designed as Grade C450L0
C N
to AS 1163 is cold-formed, and is therefore allocated the
5.0 RHS 18.2 0.479 26.3 18.0 28.0 2310 7.07 94.3 115 55.3 3.79 75.7 87.3 40.4 8.12 127 1.00 24.1 115 37.6 78.5
C N
CF residual stresses classification in AS 4100.
4.0 RHS 14.8 0.483 32.7 23.0 35.5 1880 5.87 78.2 94.6 55.9 3.15 63.0 71.8 40.9 6.64 105 0.903 30.9 93.2 47.6 55.9
N S
4. LiteOil and NoKote are available in all sections on request.
14.2 0.379 26.6 8.00 28.0 1810 4.44 59.2 78.9 49.5 0.765 30.6 35.7 20.5 2.30 56.8 1.00 10.7 78.9 37.6 31.8
150 x 50 x 5.0 RHS C N
4.0 RHS 11.6 0.383 32.9 10.5 35.5 1480 3.74 49.8 65.4 50.2 0.653 26.1 29.8 21.0 1.93 48.2 0.877 14.1 65.4 47.6 22.7
C S
3.0 RHS 8.96 0.390 43.5 14.7 48.0 1140 2.99 39.8 51.4 51.2 0.526 21.1 23.5 21.5 1.50 38.3 0.713 19.7 51.4 64.4 14.5
C S
14.7 0.330 22.5 6.50 19.2 1870 3.28 51.6 68.9 41.9 0.761 29.8 35.8 20.2 2.20 54.9 1.00 8.72 68.9 25.7 35.8
127 x 51 x 6.0 RHS C C
5.0 RHS 12.5 0.335 26.7 8.20 23.4 1590 2.89 45.6 59.9 42.6 0.679 26.6 31.3 20.6 1.93 48.6 1.00 11.0 59.9 31.4 30.6
C N
3.5 RHS 9.07 0.341 37.6 12.6 34.3 1150 2.20 34.7 44.6 43.7 0.526 20.6 23.4 21.3 1.44 37.2 0.905 16.9 44.6 46.0 18.5
C S
16.7 0.374 22.4 10.5 18.8 2130 4.16 66.6 84.2 44.2 1.87 50.0 59.1 29.6 4.44 86.2 1.00 14.1 84.2 25.3 59.1
125 x 75 x 6.0 RHS C C
5.0 RHS 14.2 0.379 26.6 13.0 23.0 1810 3.64 58.3 72.7 44.8 1.65 43.9 51.1 30.1 3.83 75.3 1.00 17.4 72.7 30.9 50.5
C N
4.0 RHS 11.6 0.383 32.9 16.8 29.3 1480 3.05 48.9 60.3 45.4 1.39 37.0 42.4 30.6 3.16 63.0 1.00 22.5 60.3 39.2 37.4
C N
3.0 RHS 8.96 0.390 43.5 23.0 39.7 1140 2.43 38.9 47.3 46.1 1.11 29.5 33.3 31.1 2.43 49.5 0.845 30.9 46.5 53.2 24.2
N S
2.5 RHS 7.53 0.391 52.0 28.0 48.0 959 2.07 33.0 40.0 46.4 0.942 25.1 28.2 31.4 2.05 42.1 0.763 37.6 34.7 64.4 18.2
N S
b y
14.7 0.330 22.5 10.7 15.0 1870 2.52 49.4 61.9 36.7 1.59 42.0 50.5 29.2 3.38 69.8 1.00 14.3 61.9 20.1 50.5
102 x 76 x 6.0 RHS C C
5.0 RHS 12.5 0.335 26.7 13.2 18.4 1590 2.22 43.5 53.7 37.3 1.41 37.0 43.9 29.7 2.91 61.2 1.00 17.7 53.7 24.7 43.9
C C
3.5 RHS 9.07 0.341 37.6 19.7 27.1 1150 1.68 33.0 39.9 38.2 1.07 28.2 32.6 30.5 2.14 46.1 1.00 26.4 39.9 36.4 29.8
C N t d x x
y
Smorgon Steel Tube Mills A.B.N. 22 010 469 977. PO Box 246 Sunnybank, Queensland 4109 Australia Telephone +61 7 3246 2600 Facsimile +61 7 3246 2660 E-mail tubemills@smorgonsteel.com.au Internet www.smorgonsteel.com.au/tubemills
DECEMBER 2006 2-18
Structural RHS DualGradeĀ® ā? Section Properties calculated to AS 1163 in accordance with AS 4100
Properties for Design to AS 4100
Dimensions and Ratios Properties
External Gross
Torsion Torsion Form
Designation Surface Section About x-axis About y-axis About x-axis About y-axis
Mass Constant Modulus Factor
b-2t d-2t
Area Area
per m Compact- Compact-
Ī»e Ī»e
d b t per m per t Ag Ix Zx Sx rx Iy Zy Sy ry J C kf Zex Zey
t t ness ness
1
1 1
RHS RHS RHS
106mm4 103mm3 103mm3 106mm4 103mm3 103mm3 106mm4 103mm3 103mm3 (C,N,S) 103mm3
m2/m m2/t mm2
mm mm mm kg/m mm mm (C,N,S)
2
2 2
DualGradeĀ® DualGradeĀ® DualGradeĀ®
12.0 0.274 22.8 6.33 14.7 1530 1.71 34.2 45.3 33.4 0.567 22.7 27.7 19.2 1.53 40.9 1.00 8.50 45.3 19.7 27.7
100 x 50 6.0 C C
x RHS 3
3 3
SupaGalĀ® KleenKoteĀ® LiteOil
5.0 10.3 0.279 27.0 8.00 18.0 1310 1.53 30.6 39.8 34.1 0.511 20.4 24.4 19.7 1.35 36.5 1.00 10.7 39.8 24.1 24.4
RHS C C
4.0 8.49 0.283 33.3 10.5 23.0 1080 1.31 26.1 33.4 34.8 0.441 17.6 20.6 20.2 1.13 31.2 1.00 14.1 33.4 30.9 20.3
RHS C N
3.5 7.53 0.285 37.9 12.3 26.6 959 1.18 23.6 29.9 35.1 0.400 16.0 18.5 20.4 1.01 28.2 1.00 16.5 29.9 35.6 17.1
RHS C N Notes:
3.0 6.60 0.290 43.9 14.7 31.3 841 1.06 21.3 26.7 35.6 0.361 14.4 16.4 20.7 0.886 25.0 0.967 19.7 26.7 42.0 13.9
RHS C S 1. For DualGradeĀ® C350L0/C450L0: fy = 450 MPa
2.5 5.56 0.291 52.4 18.0 38.0 709 0.912 18.2 22.7 35.9 0.311 12.4 14.0 20.9 0.754 21.5 0.856 24.1 22.7 51.0 10.4
RHS C S and fu = 500 MPa; fy = yield stress used in design;
2.0 4.50 0.293 65.1 23.0 48.0 574 0.750 15.0 18.5 36.2 0.257 10.3 11.5 21.2 0.616 17.7 0.746 30.9 18.2 64.4 7.33
RHS N S fu = tensile strength used in design; as defined in AS 4100
6.23 0.211 33.9 7.50 17.0 793 0.527 13.9 18.1 25.8 0.176 9.26 11.1 14.9 0.466 16.6 1.00 10.1 18.1 22.8 11.1
76 x 38 4.0 C C
x RHS ā? see Steel Grades (Part 5) of this Product Manual for a
definition of DualGradeĀ® C350L0/C450L0.
3.0 4.90 0.218 44.4 10.7 23.3 625 0.443 11.7 14.8 26.6 0.149 7.82 9.09 15.4 0.373 13.6 1.00 14.3 14.8 31.3 8.92
RHS C N
2.5 4.15 0.219 52.8 13.2 28.4 529 0.383 10.1 12.7 26.9 0.129 6.81 7.81 15.6 0.320 11.8 1.00 17.7 12.7 38.1 7.00
RHS C N 2. C = Compact Section; N = Non-Compact Section;
S = Slender Section (as defined in AS 4100).
9.67 0.224 23.2 6.33 10.5 1230 0.800 21.3 28.1 25.5 0.421 16.9 21.1 18.5 1.01 29.3 1.00 8.50 28.1 14.1 21.1
75 x 50 6.0 C C
x RHS
3. DualGradeĀ® C350L0/C450L0 designed as Grade C450L0
5.0 8.35 0.229 27.4 8.00 13.0 1060 0.726 19.4 24.9 26.1 0.384 15.4 18.8 19.0 0.891 26.4 1.00 10.7 24.9 17.4 18.8
RHS C C
to AS 1163 is cold-formed, and is therefore allocated the
4.0 6.92 0.233 33.7 10.5 16.8 881 0.630 16.8 21.1 26.7 0.335 13.4 16.0 19.5 0.754 22.7 1.00 14.1 21.1 22.5 16.0
RHS C C
CF residual stresses classification in AS 4100.
3.0 5.42 0.240 44.2 14.7 23.0 691 0.522 13.9 17.1 27.5 0.278 11.1 12.9 20.0 0.593 18.4 1.00 19.7 17.1 30.9 12.8
RHS C N
4. LiteOil and NoKote are available in all sections on request.
2.5 4.58 0.241 52.7 18.0 28.0 584 0.450 12.0 14.6 27.7 0.240 9.60 11.0 20.3 0.505 15.9 1.00 24.1 14.6 37.6 9.95
RHS C N
2.0 3.72 0.243 65.4 23.0 35.5 474 0.372 9.91 12.0 28.0 0.199 7.96 9.06 20.5 0.414 13.1 0.904 30.9 11.8 47.6 7.07
RHS N S
1.6 3.01 0.245 81.3 29.3 44.9 383 0.305 8.14 9.75 28.2 0.164 6.56 7.40 20.7 0.337 10.8 0.799 39.2 8.26 60.2 5.01
RHS N S
3.60 0.191 53.1 8.00 28.0 459 0.285 7.60 10.1 24.9 0.0487 3.89 4.53 10.3 0.144 7.14 1.00 10.7 10.1 37.6 4.05
75 x 25 2.5 C N
x RHS
2.0 2.93 0.193 65.8 10.5 35.5 374 0.238 6.36 8.31 25.3 0.0414 3.31 3.77 10.5 0.120 6.04 0.878 14.1 8.31 47.6 2.88
RHS C S
1.6 2.38 0.195 81.7 13.6 44.9 303 0.197 5.26 6.81 25.5 0.0347 2.78 3.11 10.7 0.0993 5.05 0.746 18.3 6.81 60.2 2.02
RHS C S
5.35 0.183 34.2 6.75 14.3 681 0.328 10.1 13.3 22.0 0.123 7.03 8.58 13.4 0.320 12.5 1.00 9.06 13.3 19.1 8.58
65 x 35 4.0 C C
x RHS
3.0 4.25 0.190 44.7 9.67 19.7 541 0.281 8.65 11.0 22.8 0.106 6.04 7.11 14.0 0.259 10.4 1.00 13.0 11.0 26.4 7.11
RHS C C
2.5 3.60 0.191 53.1 12.0 24.0 459 0.244 7.52 9.45 23.1 0.0926 5.29 6.13 14.2 0.223 9.10 1.00 16.1 9.45 32.2 5.95
RHS C N
2.0 2.93 0.193 65.8 15.5 30.5 374 0.204 6.28 7.80 23.4 0.0778 4.44 5.07 14.4 0.184 7.62 0.985 20.8 7.80 40.9 4.37
RHS C S
3.07 0.140 45.5 6.33 14.7 391 0.112 4.47 5.86 16.9 0.0367 2.93 3.56 9.69 0.0964 5.18 1.00 8.50 5.86 19.7 3.56
50 x 25 3.0 C C
x RHS
b y
2.5 2.62 0.141 54.0 8.00 18.0 334 0.0989 3.95 5.11 17.2 0.0328 2.62 3.12 9.91 0.0843 4.60 1.00 10.7 5.11 24.1 3.12
RHS C C
2.0 2.15 0.143 66.6 10.5 23.0 274 0.0838 3.35 4.26 17.5 0.0281 2.25 2.62 10.1 0.0706 3.92 1.00 14.1 4.26 30.9 2.58
RHS C N
1.6 1.75 0.145 82.5 13.6 29.3 223 0.0702 2.81 3.53 17.7 0.0237 1.90 2.17 10.3 0.0585 3.29 1.00 18.3 3.53 39.2 1.92
RHS C N t d x x
y
Smorgon Steel Tube Mills A.B.N. 22 010 469 977. PO Box 246 Sunnybank, Queensland 4109 Australia Telephone +61 7 3246 2600 Facsimile +61 7 3246 2660 E-mail tubemills@smorgonsteel.com.au Internet www.smorgonsteel.com.au/tubemills
DECEMBER 2006 2-19
PART 0 PART 9
PART 1 PART 2 PART 3 PART 4 PART 5 PART 6 PART 7 PART 8
Quick Reference Product Material Safety
General Information Structural Products Piping Products Other Products Steel Grades Mill Finishes Mill Processing Fabrication
Availability Guide Data Sheets (MSDS)
Blank Page
Smorgon Steel Tube Mills A.B.N. 22 010 469 977. PO Box 246 Sunnybank, Queensland 4109 Australia Telephone +61 7 3246 2600 Facsimile +61 7 3246 2660 E-mail tubemills@smorgonsteel.com.au Internet www.smorgonsteel.com.au/tubemills
DECEMBER 2006 2-20
Structural RHS DualGradeĀ® ā? Mass & Bundling calculated in accordance with AS 1163
Dimensions Bundling Mass
Bundle Configuration (mm) Bundle Dimensions (mm)
Designation Lengths Metres Nominal Mass Per Bundle
Per Bundle Per Bundle Mass tonnes
6.5 8.0 9.0 12.0 6.5 8.0 9.0 12.0
d b t
6.5 8.0 9.0 12.0 6.5 8.0 9.0 12.0 6.5 8.0 9.0 12.0
mm mm mm WxH WxH WxH WxH Wx H Wx H Wx H Wx H kg/m m/t
1
1 1
RHS RHS RHS
8 12 400 300 96 768 1.75 571 1.35
50 25 1.6 - - - - - - - - - - - - - - -
x x RHS 2
2 2
DualGradeĀ® DualGradeĀ® DualGradeĀ®
2.0 8 12 400 300 96 768 2.15 465 1.65
RHS - - - - - - - - - - - - - - - 3
3 3
SupaGalĀ® KleenKoteĀ® LiteOil
2.5 6 12 300 300 72 576 2.62 382 1.51
RHS - - - - - - - - - - - - - - -
3.0 5 12 250 300 60 480 3.07 326 1.47
RHS - - - - - - - - - - - - - - -
6 9 390 315 54 432 2.93 341 1.27
65 35 2.0 - - - - - - - - - - - - - - -
x x RHS
Notes:
2.5 6 9 390 315 54 432 3.60 278 1.56
RHS - - - - - - - - - - - - - - -
1. W = quantity along width of bundle cross-section;
3.0 5 9 325 315 45 360 4.25 236 1.53
RHS - - - - - - - - - - - - - - -
H = quantity along height of bundle cross-section.
4.0 5 7 325 245 35 280 5.35 187 1.50
RHS - - - - - - - - - - - - - - -
2. LiteOil and NoKote are available in all sections on request.
5 13 375 325 65 520 2.38 420 1.24
75 25 1.6 - - - - - - - - - - - - - - -
x x RHS
2.0 5 13 375 325 65 520 2.93 341 1.53
RHS - - - - - - - - - - - - - - -
2.5 4 12 300 300 48 384 3.60 278 1.38
RHS - - - - - - - - - - - - - - -
6 7 450 350 42 336 3.01 332 1.01
75 50 1.6 - - - - - - - - - - - - - - -
x x RHS
2.0 6 7 450 350 42 336 3.72 269 1.25
RHS - - - - - - - - - - - - - - -
2.5 6 7 450 350 42 336 4.58 218 1.54
RHS - - - - - - - - - - - - - - -
3.0 5 7 375 350 35 280 5.42 184 1.52
RHS - - - - - - - - - - - - - - -
4.0 4 7 300 350 28 224 6.92 145 1.55
RHS - - - - - - - - - - - - - - -
5.0 4 6 300 300 24 192 8.35 120 1.60
RHS - - - - - - - - - - - - - - -
6.0 4 5 300 250 20 160 9.67 103 1.55
RHS - - - - - - - - - - - - - - -
5 9 380 342 45 360 4.15 241 1.49
76 38 2.5 - - - - - - - - - - - - - - -
x x RHS
3.0 4 10 304 380 40 320 4.90 204 1.57
RHS - - - - - - - - - - - - - - -
4.0 4 8 304 304 32 256 6.23 161 1.59
RHS - - - - - - - - - - - - - - -
4 8 400 400 32 256 4.50 222 1.15
100 50 2.0 - - - - - - - - - - - - - - -
x x RHS
2.5 4 8 400 400 32 256 5.56 180 1.42
RHS - - - - - - - - - - - - - - -
3.0 4 8 400 400 32 256 6.60 152 1.69
RHS - - - - - - - - - - - - - - -
3.5 4 6 400 300 24 192 7.53 133 1.45
RHS - - - - - - - - - - - - - - -
4.0 4 6 400 300 24 192 8.49 118 1.63 b
RHS - - - - - - - - - - - - - - - y
5.0 3 6 300 300 18 144 10.3 96.9 1.49
RHS - - - - - - - - - - - - - - -
6.0 3 5 300 250 15 120 12.0 83.1 1.44
RHS - - - - - - - - - - - - - - -
t d x x
y
Smorgon Steel Tube Mills A.B.N. 22 010 469 977. PO Box 246 Sunnybank, Queensland 4109 Australia Telephone +61 7 3246 2600 Facsimile +61 7 3246 2660 E-mail tubemills@smorgonsteel.com.au Internet www.smorgonsteel.com.au/tubemills
DECEMBER 2006 2-21
PART 0 PART 9
PART 1 PART 2 PART 3 PART 4 PART 5 PART 6 PART 7 PART 8
Quick Reference Product Material Safety
General Information Structural Products Piping Products Other Products Steel Grades Mill Finishes Mill Processing Fabrication
Availability Guide Data Sheets (MSDS)
Structural RHS DualGradeĀ® ā? Mass & Bundling calculated in accordance with AS 1163
Dimensions Bundling Mass
Bundle Configuration (mm) Bundle Dimensions (mm)
Designation Lengths Metres Nominal Mass Per Bundle
Per Bundle Per Bundle Mass tonnes
6.5 8.0 9.0 12.0 6.5 8.0 9.0 12.0
d b t
6.5 8.0 9.0 12.0 6.5 8.0 9.0 12.0 6.5 8.0 9.0 12.0
mm mm mm WxH WxH WxH WxH Wx H Wx H Wx H Wx H kg/m m/t
1
1 1
RHS RHS RHS
4 5 408 380 20 160 9.07 110 1.45
102 76 x 3.5 RHS - - - - - - - - - - - - - - -
x 2
2 2
DualGradeĀ® DualGradeĀ® DualGradeĀ®
5.0 RHS 4 4 408 304 16 128 12.5 79.9 1.60
- - - - - - - - - - - - - - - 3
3 3
SupaGalĀ® KleenKoteĀ® LiteOil
6.0 RHS 3 4 306 304 12 96 14.7 68.2 1.41
- - - - - - - - - - - - - - -
4 5 500 375 20 160 7.53 133 1.20
125 75 x 2.5 RHS - - - - - - - - - - - - - - -
x
3.0 RHS 4 5 500 375 20 160 8.96 112 1.43
- - - - - - - - - - - - - - -
Notes:
4.0 RHS 3 5 375 375 15 120 11.6 86.0 1.40
- - - - - - - - - - - - - - -
1. W = quantity along width of bundle cross-section;
5.0 RHS 3 5 375 375 15 120 14.2 70.2 1.71
- - - - - - - - - - - - - - -
H = quantity along height of bundle cross-section.
6.0 RHS 3 4 375 300 12 96 16.7 59.7 1.61
- - - - - - - - - - - - - - -
2. LiteOil and NoKote are available in all sections on request.
3 7 381 357 21 168 9.07 110 1.52
127 51 x 3.5 RHS - - - - - - - - - - - - - - -
x
5.0 RHS 3 6 381 306 18 144 12.5 79.9 1.80
- - - - - - - - - - - - - - -
6.0 RHS 2 7 254 357 14 112 14.7 68.2 1.64
- - - - - - - - - - - - - - -
3 7 450 350 21 168 8.96 112 1.50
150 50 x 3.0 RHS - - - - - - - - - - - - - - -
x
4.0 RHS 3 5 450 250 15 120 11.6 86.0 1.40
- - - - - - - - - - - - - - -
5.0 RHS 3 5 2 5 450 250 300 250 15 10 120 120 14.2 70.2 1.71 1.71
- - - - - - - - - -
3 4 3 3 450 400 450 300 12 9 96 108 14.8 67.7 1.42 1.59
150 100 x 4.0 RHS - - - - - - - - - -
x
5.0 RHS 3 4 2 4 450 400 300 400 12 8 96 96 18.2 55.0 1.74 1.74
- - - - - - - - - -
6.0 RHS 3 3 2 3 450 300 300 300 9 6 72 72 21.4 46.6 1.54 1.54
- - - - - - - - - -
8.0 RHS 3 2 2 2 450 200 300 200 6 4 48 48 27.7 36.1 1.33 1.33
- - - - - - - - - -
9.0 RHS 3 2 2 2 450 200 300 200 6 4 48 48 30.6 32.7 1.47 1.47
- - - - - - - - - -
10.0 RHS 2 2 300 200 4 48 33.4 29.9 1.60
- - - - - - - - - - - - - -
3 4 3 4 456 304 456 304 12 12 96 144 16.4 60.8 1.58 2.37
152 76 x 5.0 RHS - - - - - - - - - -
x
6.0 RHS 3 3 3 3 456 228 456 228 9 9 72 108 19.4 51.6 1.40 2.09
- - - - - - - - - -
2 4 2 3 400 400 400 300 8 6 64 72 17.9 55.8 1.15 1.29
200 100 x 4.0 RHS - - - - - - - - - -
x
5.0 RHS 2 4 2 3 400 400 400 300 8 6 64 72 22.1 45.3 1.41 1.59
- - - - - - - - - -
6.0 RHS 2 4 2 2 400 400 400 200 8 4 64 48 26.2 38.2 1.67 1.26
- - - - - - - - - -
8.0 RHS 2 3 2 2 400 300 400 200 6 4 48 48 33.9 29.5 1.63 1.63
- - - - - - - - - -
b
9.0 RHS 2 3 2 2 400 300 400 200 6 4 48 48 37.7 26.6 1.81 1.81
- - - - - - - - - - y
10.0 RHS 1 2 200 200 2 24 41.3 24.2 0.99
- - - - - - - - - - - - - - -
t d x x
y
Smorgon Steel Tube Mills A.B.N. 22 010 469 977. PO Box 246 Sunnybank, Queensland 4109 Australia Telephone +61 7 3246 2600 Facsimile +61 7 3246 2660 E-mail tubemills@smorgonsteel.com.au Internet www.smorgonsteel.com.au/tubemills
DECEMBER 2006 2-22
Structural RHS DualGradeĀ® ā? Mass & Bundling calculated in accordance with AS 1163
Dimensions Bundling Mass
Bundle Configuration (mm) Bundle Dimensions (mm)
Designation Lengths Metres Nominal Mass Per Bundle
Per Bundle Per Bundle Mass tonnes
6.5 8.0 9.0 12.0 6.5 8.0 9.0 12.0
d b t
6.5 8.0 9.0 12.0 6.5 8.0 9.0 12.0 6.5 8.0 9.0 12.0
mm mm mm WxH WxH WxH WxH Wx H Wx H Wx H Wx H kg/m m/t
1
1 1
RHS RHS RHS
2 3 2 2 500 450 500 300 6 4 48 48 29.9 33.4 1.44 1.44
250 150 x 5.0 RHS - - - - - - - - - -
x 2
2 2
DualGradeĀ® DualGradeĀ® DualGradeĀ®
6.0 RHS 2 2 2 2 500 300 500 300 4 4 32 48 35.6 28.1 1.14 1.71
- - - - - - - - - - 3
3 3
SupaGalĀ® KleenKoteĀ® LiteOil
8.0 RHS 2 2 1 2 500 300 250 300 4 2 32 24 46.5 21.5 1.49 1.12
- - - - - - - - - -
9.0 RHS 2 2 1 2 500 300 250 300 4 2 32 24 51.8 19.3 1.66 1.24
- - - - - - - - - -
10.0 RHS 1 2 250 300 2 24 57.0 17.6 1.37
- - - - - - - - - - - - - - -
Notes:
12.5 RHS 1 2 250 300 2 24 69.4 14.4 1.67
- - - - - - - - - - - - - - -
1. W = quantity along width of bundle cross-section;
16.0 RHS 1 1 250 150 1 12 85.5 11.7 1.03
- - - - - - - - - - - - - - -
H = quantity along height of bundle cross-section.
1 2 300 400 2 24 45.0 22.2 1.08
300 200 x 6.0 RHS - - - - - - - - - - - - - - -
x
2. LiteOil and NoKote are available in all sections on request.
8.0 RHS 1 2 300 400 2 24 59.1 16.9 1.42
- - - - - - - - - - - - - - -
10.0 RHS 1 2 300 400 2 24 72.7 13.8 1.74
- - - - - - - - - - - - - - -
12.5 RHS 1 1 300 200 1 12 89.0 11.2 1.07
- - - - - - - - - - - - - - -
16.0 RHS 1 1 300 200 1 12 111 9.04 1.33
- - - - - - - - - - - - - - -
1 2 350 500 2 24 54.4 18.4 1.31
350 250 x 6.0 RHS - - - - - - - - - - - - - - -
x
8.0 RHS 1 2 350 500 2 24 71.6 14.0 1.72
- - - - - - - - - - - - - - -
10.0 RHS 1 1 350 250 1 12 88.4 11.3 1.06
- - - - - - - - - - - - - - -
12.5 RHS 1 1 350 250 1 12 109 9.21 1.30
- - - - - - - - - - - - - - -
16.0 RHS 1 1 350 250 1 12 136 7.36 1.63
- - - - - - - - - - - - - - -
1 2 400 400 2 24 71.6 14.0 1.72
400 200 x 8.0 RHS - - - - - - - - - - - - - - -
x
10.0 RHS 1 1 400 200 1 12 88.4 11.3 1.06
- - - - - - - - - - - - - - -
12.5 RHS 1 1 400 200 1 12 109 9.21 1.30
- - - - - - - - - - - - - - -
16.0 RHS 1 1 400 200 1 12 136 7.36 1.63
- - - - - - - - - - - - - - -
1 1 400 300 1 12 84.2 11.9 1.01
400 300 x 8.0 RHS - - - - - - - - - - - - - - -
x
10.0 RHS 1 1 400 300 1 12 104 9.61 1.25
- - - - - - - - - - - - - - -
12.5 RHS 1 1 400 300 1 12 128 7.80 1.54
- - - - - - - - - - - - - - -
16.0 RHS 1 1 400 300 1 12 161 6.21 1.93
- - - - - - - - - - - - - - -
b y
t d x x
y
Smorgon Steel Tube Mills A.B.N. 22 010 469 977. PO Box 246 Sunnybank, Queensland 4109 Australia Telephone +61 7 3246 2600 Facsimile +61 7 3246 2660 E-mail tubemills@smorgonsteel.com.au Internet www.smorgonsteel.com.au/tubemills
DECEMBER 2006 2-23
PART 0 PART 9
PART 1 PART 2 PART 3 PART 4 PART 5 PART 6 PART 7 PART 8
Quick Reference Product Material Safety
General Information Structural Products Piping Products Other Products Steel Grades Mill Finishes Mill Processing Fabrication
Availability Guide Data Sheets (MSDS)
Blank Page
Smorgon Steel Tube Mills A.B.N. 22 010 469 977. PO Box 246 Sunnybank, Queensland 4109 Australia Telephone +61 7 3246 2600 Facsimile +61 7 3246 2660 E-mail tubemills@smorgonsteel.com.au Internet www.smorgonsteel.com.au/tubemills
DECEMBER 2006 2-24
Structural SHS DualGradeĀ® ā? Specifications
Technical Specifications See Quick Reference Product Availability Guide (Part 0) Contact your Smorgon Steel Tube Mills representative
for further information on availability. for further details.
Australian Standards
KleenKoteĀ® Finish Non-Standard Lengths
Structural SHS DualGradeĀ® C350L0/C450L0
Structural SHS DualGradeĀ® C350L0/C450L0 Special orders of non-standard pack lengths of Structural
is manufactured and tested to comply with the
with KleenKoteĀ® finish is supplied in the following RHS DualGradeĀ® C350L0/C450L0 are available (conditions 1 1 1
SHS SHS SHS
requirements of the following specifications:
surface colours: apply). Check with your distributor for details. 2 2 2
DualGradeĀ® DualGradeĀ® DualGradeĀ®
AS 1163 ā? Structural steel hollow sections 3 3 3
SupaGalĀ® KleenKoteĀ® LiteOil
Minimum Length:
Blue Black
(Grade C350L0 and Grade C450L0).
This primer paint finish is applied in-line using the (20x20 ā? 100x100 SHS) SupaGalĀ®/KleenKoteĀ® _ 4.2 m
_
AS/NZS 4792 ā? Hot-dip galvanized (zinc) coatings
patented KleenKoteĀ® process and is supplied in the (125x125 ā? 200x200 SHS) KleenKoteĀ®_________ 5.3 m
General Description
on ferrous hollow sections, applied by a continuous
following coating thicknesses:
or a specialized process (Section 3). Maximum Length:
Manufacturing Process
Blue & Black _______________ Target 12 microns with
(20x20 ā? 100x100 SHS) SupaGalĀ®/KleenKoteĀ® __ 8.0 m
Mechanical Properties ________________________ average at 8-10 microns
Structural SHS DualGradeĀ® C350L0/C450L0, for general
Ā®/KleenKoteĀ® _12.2 m
_
(50x50 ā? 200x200 SHS) SupaGal
Note: Non-standard finishes, such as NoKote, are
Structural SHS DualGradeĀ® C350L0/C450L0 has the fabrication and structural applications, is manufactured
Note: Contact your Smorgon Steel Tube Mills
available if ordered prior to rollings. Conditions apply.
following mechanical properties: by cold-forming and high frequency Electric Resistance
representative for lengths outside this range.
Refer to manufacturer for details.
Welding (ERW) of high strength steel strip. The cold-
450 MPa
Minimum Yield Strength _________________
Thickness
See Quick Reference Product Availability Guide (Part 0) forming process enhances the strength, hardness and
500 MPa
Minimum Tensile Strength ______________
_
for further information on availability. surface finish of the tube and produces product to tight
Structural SHS DualGradeĀ® C350L0/C450L0 is available in
Minimum Elongation in 5.65āSo ______________ 16%
LiteOil Finish dimensional tolerances.
1.6 mm to 16.0 mm wall thicknesses. These thicknesses
L0 __ guaranteed impact properties at 0Ā°C to AS 1163
_
are identified by the following end colour codes: Further Information
LiteOil tubular products use a light oil coating which
Note: Although the minimum elongation is 16%, in-house
_________________________________ Purple
is the standard finish for medium to large sized SHS. 1.6 mm
testing indicates the typical elongation is approximately 22%. For further information refer to the Smorgon Steel Tube Mills:
_________________________________ Brown
See Quick Reference Product Availability Guide (Part 0) 1.8 mm
Tolerances Product Solutions Guide.
_________________________________ Yellow
for further information on availability. 2.0 mm
Tolerances for Structural SHS DualGradeĀ® ___________________________________ Pink
2.5 mm
End Finish (Mill Processing)
C350L0/C450L0 are compliant with AS 1163. ___________________________________ Blue
3.0 mm
See Dimensional Tolerances in Part 1 for more information. Plain Ends only. ___________________________________Grey
3.5 mm
Standard Lengths _________________________________ Green
Supply Conditions 4.0 mm
________________________________ Orange
5.0 mm
Standard lengths for Structural SHS DualGradeĀ®
SupaGalĀ® Finish _________________________________ Cream
C350L0/C450L0: 6.0 mm
___________________________________ Red
Structural RHS DualGradeĀ® C350L0/C450L0 with (20x20 ā? 25x25 SHS) SupaGalĀ®/KleenKoteĀ® __ 6.5 m 8.0 mm
SupaGalĀ® finish is manufactured using steel strip that _________________________________ Purple
(30x30 ā? 89x89 SHS) SupaGalĀ®/KleenKoteĀ® __ 8.0 m
_ 9.0 mm
has the following coating thickness: 10.0 mm _______________________________ Yellow
_
(100x100 ā? 400x400 SHS)
100 g/m2 each side SupaGalĀ®/KleenKoteĀ®/LiteOil ______________ 12.0 m 12.5 mm _________________________________ Blue
_
Minimum coating mass ________
AS/NZS 4792 ZB 100/100 May exclude some wall thicknesses and finishes. 16.0 mm _________________________________Grey
_
Designated as __________
Smorgon Steel Tube Mills A.B.N. 22 010 469 977. PO Box 246 Sunnybank, Queensland 4109 Australia Telephone +61 7 3246 2600 Facsimile +61 7 3246 2660 E-mail tubemills@smorgonsteel.com.au Internet www.smorgonsteel.com.au/tubemills
DECEMBER 2006 2-25
PART 0 PART 9
PART 1 PART 2 PART 3 PART 4 PART 5 PART 6 PART 7 PART 8
Quick Reference Product Material Safety
General Information Structural Products Piping Products Other Products Steel Grades Mill Finishes Mill Processing Fabrication
Availability Guide Data Sheets (MSDS)
Blank Page
Smorgon Steel Tube Mills A.B.N. 22 010 469 977. PO Box 246 Sunnybank, Queensland 4109 Australia Telephone +61 7 3246 2600 Facsimile +61 7 3246 2660 E-mail tubemills@smorgonsteel.com.au Internet www.smorgonsteel.com.au/tubemills
DECEMBER 2006 2-26
Structural SHS DualGradeĀ® ā? Section Properties calculated to AS 1163 in accordance with AS 4100
Properties for Design to AS 4100
Dimensions and Ratios Section Properties
External Gross
Torsion Torsion Form
Mass About x and y-axis
Designation Surface Section About x-, y- and n-axis Constant Modulus Factor
per b-2t
Area Area Compact-
m
Ī»e
d b t per m per t Ag Ix Zx Zn Sx rx J C kf Zex
t ness
10 6 mm4 10 3 mm 3 10 3 mm 3 10 3 mm 3 10 6 mm4 10 3 mm 3 10 3 mm 3 1 1 1
m 2 /m m 2 /t mm 2
mm mm mm kg/m mm (C,N,S) SHS SHS SHS
2 2 2
DualGradeĀ® DualGradeĀ® DualGradeĀ®
186 1.53 8.23 23.0 23700 571 2850 2140 3370 155 930 4350 1.00 30.9 3320
400 400 16.0 N
x x SHS 3 3 3
SupaGalĀ® KleenKoteĀ® LiteOil
12.5 148 1.55 10.5 30.0 18800 464 2320 1720 2710 157 744 3520 0.994 40.2 2310
SHS S
10.0 120 1.56 13.0 38.0 15300 382 1910 1400 2210 158 604 2890 0.785 51.0 1650
SHS S
161 1.33 8.27 19.9 20500 372 2130 1610 2530 135 614 3250 1.00 26.7 2530
350 350 16.0 C
x x SHS
Notes:
12.5 128 1.35 10.5 26.0 16300 305 1740 1300 2040 137 493 2650 1.00 34.9 1900
SHS N
1. For DualGradeĀ® C350L0/C450L0: fy = 450 MPa
10.0 104 1.36 13.0 33.0 13300 252 1440 1060 1670 138 401 2180 0.904 44.3 1350
SHS S
and fu = 500 MPa; fy = yield stress used in design;
8.0 84.2 1.37 16.2 41.8 10700 207 1180 865 1370 139 326 1790 0.715 56.0 971
SHS S fu = tensile strength used in design; as defined in AS 4100
136 1.13 8.33 16.8 17300 226 1510 1160 1810 114 378 2310 1.00 22.5 1810
300 300 16.0 C
x x SHS ā? see Steel Grades (Part 5) of this Product Manual for a
12.5 109 1.15 10.6 22.0 13800 187 1240 937 1470 116 305 1900 1.00 29.5 1470
SHS C definition of DualGradeĀ® C350L0/C450L0.
10.0 88.4 1.16 13.1 28.0 11300 155 1030 769 1210 117 250 1570 1.00 37.6 1080
SHS N 2. C = Compact Section; N = Non-Compact Section;
8.0 71.6 1.17 16.3 35.5 9120 128 853 628 991 118 203 1290 0.840 47.6 768
SHS S S = Slender Section (as defined in AS 4100).
111 0.931 8.42 13.6 14100 124 992 774 1210 93.8 212 1530 1.00 18.3 1210
250 250 16.0 C
x x SHS 3. DualGradeĀ® C350L0/C450L0 designed as Grade C450L0
12.5 89.0 0.946 10.6 18.0 11300 104 830 634 992 95.7 173 1270 1.00 24.1 992
SHS C to AS 1163 is cold-formed, and is therefore allocated the
10.0 72.7 0.957 13.2 23.0 9260 87.1 697 523 822 97.0 142 1060 1.00 30.9 811 CF residual stresses classification in AS 4100.
SHS N
9.0 65.9 0.961 14.6 25.8 8400 79.8 639 477 750 97.5 129 972 1.00 34.6 699
SHS N 4. LiteOil and NoKote are available in all sections on request.
8.0 59.1 0.966 16.3 29.3 7520 72.3 578 429 676 98.0 116 878 1.00 39.2 586
SHS N
6.0 45.0 0.974 21.7 39.7 5730 56.2 450 330 521 99.0 88.7 681 0.753 53.2 380
SHS S
85.5 0.731 8.55 10.5 10900 58.6 586 469 728 73.3 103 914 1.00 14.1 728
200 200 16.0 C
x x SHS
12.5 69.4 0.746 10.8 14.0 8840 50.0 500 389 607 75.2 85.2 772 1.00 18.8 607
SHS C
10.0 57.0 0.757 13.3 18.0 7260 42.5 425 324 508 76.5 70.7 651 1.00 24.1 508
SHS C
9.0 51.8 0.761 14.7 20.2 6600 39.2 392 297 465 77.1 64.5 599 1.00 27.1 465
SHS C
8.0 46.5 0.766 16.5 23.0 5920 35.7 357 268 421 77.6 58.2 544 1.00 30.9 415
SHS N
6.0 35.6 0.774 21.8 31.3 4530 28.0 280 207 327 78.6 44.8 425 0.952 42.0 272
SHS S
5.0 29.9 0.779 26.0 38.0 3810 23.9 239 175 277 79.1 37.8 362 0.785 51.0 207
SHS S
b y
n
x x
d
t
n y
Smorgon Steel Tube Mills A.B.N. 22 010 469 977. PO Box 246 Sunnybank, Queensland 4109 Australia Telephone +61 7 3246 2600 Facsimile +61 7 3246 2660 E-mail tubemills@smorgonsteel.com.au Internet www.smorgonsteel.com.au/tubemills
DECEMBER 2006 2-27
PART 0 PART 9
PART 1 PART 2 PART 3 PART 4 PART 5 PART 6 PART 7 PART 8
Quick Reference Product Material Safety
General Information Structural Products Piping Products Other Products Steel Grades Mill Finishes Mill Processing Fabrication
Availability Guide Data Sheets (MSDS)
Structural SHS DualGradeĀ® ā? Section Properties calculated to AS 1163 in accordance with AS 4100
Properties for Design to AS 4100
Dimensions and Ratios Section Properties
External Gross
Torsion Torsion Form
Mass About x and y-axis
Designation Surface Section About x-, y- and n-axis Constant Modulus Factor
per b-2t
Area Area Compact-
m
Ī»e
d b t per m per t Ag Ix Zx Zn Sx rx J C kf Zex
t ness
10 6 mm4 10 3 mm 3 10 3 mm 3 10 3 mm 3 10 6 mm4 10 3 mm 3 10 3 mm 3 1 1 1
m 2 /m m 2 /t mm 2
mm mm mm kg/m mm (C,N,S) SHS SHS SHS
2 2 2
DualGradeĀ® DualGradeĀ® DualGradeĀ®
41.3 0.557 13.5 13.0 5260 16.5 220 173 269 56.1 28.4 341 1.00 17.4 269
150 150 10.0 C
x x SHS 3 3 3
SupaGalĀ® KleenKoteĀ® LiteOil
9.0 37.7 0.561 14.9 14.7 4800 15.4 205 159 248 56.6 26.1 316 1.00 19.7 248
SHS C
8.0 33.9 0.566 16.7 16.8 4320 14.1 188 144 226 57.1 23.6 289 1.00 22.5 226
SHS C
6.0 26.2 0.574 22.0 23.0 3330 11.3 150 113 178 58.2 18.4 229 1.00 30.9 175
SHS N
Notes:
5.0 22.1 0.579 26.2 28.0 2810 9.70 129 96.2 151 58.7 15.6 197 1.00 37.6 135
SHS N
1. For DualGradeĀ® C350L0/C450L0: fy = 450 MPa
33.4 0.457 13.7 10.5 4260 8.93 143 114 178 45.8 15.7 223 1.00 14.1 178
125 125 10.0 C
x x SHS
and fu = 500 MPa; fy = yield stress used in design;
9.0 30.6 0.461 15.1 11.9 3900 8.38 134 106 165 46.4 14.5 208 1.00 16.0 165
SHS C fu = tensile strength used in design; as defined in AS 4100
8.0 27.7 0.466 16.8 13.6 3520 7.75 124 96.8 151 46.9 13.3 192 1.00 18.3 151
SHS C ā? see Steel Grades (Part 5) of this Product Manual for a
6.0 21.4 0.474 22.1 18.8 2730 6.29 101 76.5 120 48.0 10.4 154 1.00 25.3 120
SHS C definition of DualGradeĀ® C350L0/C450L0.
5.0 18.2 0.479 26.3 23.0 2310 5.44 87.1 65.4 103 48.5 8.87 133 1.00 30.9 101
SHS N 2. C = Compact Section; N = Non-Compact Section;
4.0 14.8 0.483 32.7 29.3 1880 4.52 72.3 53.6 84.5 49.0 7.25 110 1.00 39.2 73.2
SHS N S = Slender Section (as defined in AS 4100).
25.6 0.357 14.0 8.00 3260 4.11 82.2 68.1 105 35.5 7.50 130 1.00 10.7 105
100 100 10.0 C
x x SHS 3. DualGradeĀ® C350L0/C450L0 designed as Grade C450L0
9.0 23.5 0.361 15.4 9.11 3000 3.91 78.1 63.6 98.6 36.1 7.00 123 1.00 12.2 98.6
SHS C to AS 1163 is cold-formed, and is therefore allocated the
8.0 21.4 0.366 17.1 10.5 2720 3.66 73.2 58.6 91.1 36.7 6.45 114 1.00 14.1 91.1 CF residual stresses classification in AS 4100.
SHS C
6.0 16.7 0.374 22.4 14.7 2130 3.04 60.7 47.1 73.5 37.7 5.15 93.6 1.00 19.7 73.5
SHS C 4. LiteOil and NoKote are available in all sections on request.
5.0 14.2 0.379 26.6 18.0 1810 2.66 53.1 40.5 63.5 38.3 4.42 81.4 1.00 24.1 63.5
SHS C
4.0 11.6 0.383 32.9 23.0 1480 2.23 44.6 33.5 52.6 38.8 3.63 68.0 1.00 30.9 51.9
SHS N
3.0 8.96 0.390 43.5 31.3 1140 1.77 35.4 26.0 41.2 39.4 2.79 53.2 0.952 42.0 34.4
SHS S
2.5 7.53 0.391 52.0 38.0 959 1.51 30.1 21.9 34.9 39.6 2.35 45.2 0.787 51.0 26.1
SHS S
14.7 0.330 22.5 12.8 1870 2.06 46.4 36.4 56.7 33.2 3.55 71.8 1.00 17.2 56.7
89 89 6.0 C
x x SHS
5.0 12.5 0.335 26.7 15.8 1590 1.82 40.8 31.5 49.2 33.8 3.06 62.8 1.00 21.2 49.2
SHS C
3.5 9.07 0.341 37.6 23.4 1150 1.38 31.0 23.3 36.5 34.6 2.25 47.2 1.00 31.4 35.8
SHS N
2.0 5.38 0.349 64.9 42.5 686 0.858 19.3 14.0 22.3 35.4 1.33 29.0 0.704 57.0 15.7
SHS S
b y
n
x x
d
t
n y
Smorgon Steel Tube Mills A.B.N. 22 010 469 977. PO Box 246 Sunnybank, Queensland 4109 Australia Telephone +61 7 3246 2600 Facsimile +61 7 3246 2660 E-mail tubemills@smorgonsteel.com.au Internet www.smorgonsteel.com.au/tubemills
DECEMBER 2006 2-28
Structural SHS DualGradeĀ® ā? Section Properties calculated to AS 1163 in accordance with AS 4100
Properties for Design to AS 4100
Dimensions and Ratios Section Properties
External Gross
Torsion Torsion Form
Mass About x and y-axis
Designation Surface Section About x-, y- and n-axis Constant Modulus Factor
per b-2t
Area Area Compact-
m
Ī»e
d b t per m per t Ag Ix Zx Zn Sx rx J C kf Zex
t ness
10 6 mm4 10 3 mm 3 10 3 mm 3 10 3 mm 3 10 6 mm4 10 3 mm 3 10 3 mm 3 1 1 1
m 2 /m m 2 /t mm 2
mm mm mm kg/m mm (C,N,S) SHS SHS SHS
2 2 2
DualGradeĀ® DualGradeĀ® DualGradeĀ®
12.0 0.274 22.8 10.5 1530 1.16 30.9 24.7 38.4 27.5 2.04 48.2 1.00 14.1 38.4
75 75 6.0 C
x x SHS 3 3 3
SupaGalĀ® KleenKoteĀ® LiteOil
5.0 10.3 0.279 27.0 13.0 1310 1.03 27.5 21.6 33.6 28.0 1.77 42.6 1.00 17.4 33.6
SHS C
4.0 8.49 0.283 33.3 16.8 1080 0.882 23.5 18.1 28.2 28.6 1.48 36.1 1.00 22.5 28.2
SHS C
3.5 7.53 0.285 37.9 19.4 959 0.797 21.3 16.1 25.3 28.8 1.32 32.5 1.00 26.1 25.3
SHS C
Notes:
3.0 6.60 0.290 43.9 23.0 841 0.716 19.1 14.2 22.5 29.2 1.15 28.7 1.00 30.9 22.2
SHS N
1. For DualGradeĀ® C350L0/C450L0: fy = 450 MPa
2.5 5.56 0.291 52.4 28.0 709 0.614 16.4 12.0 19.1 29.4 0.971 24.6 1.00 37.6 17.0
SHS N
and fu = 500 MPa; fy = yield stress used in design;
2.0 4.50 0.293 65.1 35.5 574 0.505 13.5 9.83 15.6 29.7 0.790 20.2 0.841 47.6 12.1
SHS S fu = tensile strength used in design; as defined in AS 4100
10.1 0.234 23.1 8.83 1290 0.706 21.7 17.8 27.5 23.4 1.27 34.2 1.00 11.9 27.5
65 65 6.0 C
x x SHS ā? see Steel Grades (Part 5) of this Product Manual for a
5.0 8.75 0.239 27.3 11.0 1110 0.638 19.6 15.6 24.3 23.9 1.12 30.6 1.00 14.8 24.3
SHS C definition of DualGradeĀ® C350L0/C450L0.
4.0 7.23 0.243 33.6 14.3 921 0.552 17.0 13.2 20.6 24.5 0.939 26.2 1.00 19.1 20.6
SHS C 2. C = Compact Section; N = Non-Compact Section;
3.0 5.66 0.250 44.1 19.7 721 0.454 14.0 10.4 16.6 25.1 0.733 21.0 1.00 26.4 16.6
SHS C S = Slender Section (as defined in AS 4100).
2.5 4.78 0.251 52.6 24.0 609 0.391 12.0 8.91 14.1 25.3 0.624 18.1 1.00 32.2 13.7
SHS N 3. DualGradeĀ® C350L0/C450L0 designed as Grade C450L0
2.0 3.88 0.253 65.3 30.5 494 0.323 9.94 7.29 11.6 25.6 0.509 14.9 0.978 40.9 9.80
SHS S to AS 1163 is cold-formed, and is therefore allocated the
1.6 3.13 0.255 81.2 38.6 399 0.265 8.16 5.94 9.44 25.8 0.414 12.2 0.774 51.8 7.01 CF residual stresses classification in AS 4100.
SHS S
7.32 0.174 23.8 6.33 932 0.275 11.0 9.45 14.5 17.2 0.518 17.7 1.00 8.50 14.5
50 50 6.0 C
x x SHS 4. LiteOil and NoKote are available in all sections on request.
5.0 6.39 0.179 27.9 8.00 814 0.257 10.3 8.51 13.2 17.8 0.469 16.3 1.00 10.7 13.2
SHS C
4.0 5.35 0.183 34.2 10.5 681 0.229 9.15 7.33 11.4 18.3 0.403 14.3 1.00 14.1 11.4
SHS C
3.0 4.25 0.190 44.7 14.7 541 0.195 7.79 5.92 9.39 19.0 0.321 11.8 1.00 19.7 9.39
SHS C
2.5 3.60 0.191 53.1 18.0 459 0.169 6.78 5.09 8.07 19.2 0.275 10.2 1.00 24.1 8.07
SHS C
2.0 2.93 0.193 65.8 23.0 374 0.141 5.66 4.20 6.66 19.5 0.226 8.51 1.00 30.9 6.58
SHS N
1.6 2.38 0.195 81.7 29.3 303 0.117 4.68 3.44 5.46 19.6 0.185 7.03 1.00 39.2 4.74
SHS N
4.09 0.143 34.9 8.00 521 0.105 5.26 4.36 6.74 14.2 0.192 8.33 1.00 10.7 6.74
40 40 4.0 C
x x SHS
3.0 3.30 0.150 45.3 11.3 421 0.0932 4.66 3.61 5.72 14.9 0.158 7.07 1.00 15.2 5.72
SHS C
2.5 2.82 0.151 53.7 14.0 359 0.0822 4.11 3.13 4.97 15.1 0.136 6.21 1.00 18.8 4.97
SHS C
2.0 2.31 0.153 66.4 18.0 294 0.0694 3.47 2.61 4.13 15.4 0.113 5.23 1.00 24.1 4.13
SHS C
1.6 1.88 0.155 82.3 23.0 239 0.0579 2.90 2.15 3.41 15.6 0.0927 4.36 1.00 30.9 3.37
SHS N b y
n
x x
d
t
n y
Smorgon Steel Tube Mills A.B.N. 22 010 469 977. PO Box 246 Sunnybank, Queensland 4109 Australia Telephone +61 7 3246 2600 Facsimile +61 7 3246 2660 E-mail tubemills@smorgonsteel.com.au Internet www.smorgonsteel.com.au/tubemills
DECEMBER 2006 2-29
PART 0 PART 9
PART 1 PART 2 PART 3 PART 4 PART 5 PART 6 PART 7 PART 8
Quick Reference Product Material Safety
General Information Structural Products Piping Products Other Products Steel Grades Mill Finishes Mill Processing Fabrication
Availability Guide Data Sheets (MSDS)
Structural SHS DualGradeĀ® ā? Section Properties calculated to AS 1163 in accordance with AS 4100
Properties for Design to AS 4100
Dimensions and Ratios Section Properties
External Gross
Torsion Torsion Form
Mass About x and y-axis
Designation Surface Section About x-, y- and n-axis Constant Modulus Factor
per b-2t
Area Area Compact-
m
Ī»e
d b t per m per t Ag Ix Zx Zn Sx rx J C kf Zex
t ness
10 6 mm4 10 3 mm 3 10 3 mm 3 10 3 mm 3 10 6 mm4 10 3 mm 3 10 3 mm 3 1 1 1
m 2 /m m 2 /t mm 2
mm mm mm kg/m mm (C,N,S) SHS SHS SHS
2 2 2
DualGradeĀ® DualGradeĀ® DualGradeĀ®
2.83 0.130 45.8 9.67 361 0.0595 3.40 2.67 4.23 12.8 0.102 5.18 1.00 13.0 4.23
35 35 3.0 C
x x SHS 3 3 3
SupaGalĀ® KleenKoteĀ® LiteOil
2.5 2.42 0.131 54.2 12.0 309 0.0529 3.02 2.33 3.69 13.1 0.0889 4.58 1.00 16.1 3.69
SHS C
2.0 1.99 0.133 66.8 15.5 254 0.0451 2.58 1.95 3.09 13.3 0.0741 3.89 1.00 20.8 3.09
SHS C
1.6 1.63 0.135 82.7 19.9 207 0.0379 2.16 1.62 2.57 13.5 0.0611 3.26 1.00 26.7 2.57
SHS C
Notes:
2.36 0.110 46.5 8.00 301 0.0350 2.34 1.87 2.96 10.8 0.0615 3.58 1.00 10.7 2.96
30 30 3.0 C
x x SHS
1. For DualGradeĀ® C350L0/C450L0: fy = 450 MPa
2.5 2.03 0.111 54.8 10.0 259 0.0316 2.10 1.65 2.61 11.0 0.0540 3.20 1.00 13.4 2.61
SHS C
and fu = 500 MPa; fy = yield stress used in design;
2.0 1.68 0.113 67.4 13.0 214 0.0272 1.81 1.39 2.21 11.3 0.0454 2.75 1.00 17.4 2.21
SHS C fu = tensile strength used in design; as defined in AS 4100
1.6 1.38 0.115 83.3 16.8 175 0.0231 1.54 1.16 1.84 11.5 0.0377 2.32 1.00 22.5 1.84
SHS C ā? see Steel Grades (Part 5) of this Product Manual for a
1.89 0.0897 47.4 6.33 241 0.0184 1.47 1.21 1.91 8.74 0.0333 2.27 1.00 8.50 1.91
25 25 3.0 C
x x SHS definition of DualGradeĀ® C350L0/C450L0.
2.5 1.64 0.0914 55.7 8.00 209 0.0169 1.35 1.08 1.71 8.99 0.0297 2.07 1.00 10.7 1.71
SHS C 2. C = Compact Section; N = Non-Compact Section;
2.0 1.36 0.0931 68.3 10.5 174 0.0148 1.19 0.926 1.47 9.24 0.0253 1.80 1.00 14.1 1.47
SHS C S = Slender Section (as defined in AS 4100).
1.6 1.12 0.0945 84.1 13.6 143 0.0128 1.02 0.780 1.24 9.44 0.0212 1.54 1.00 18.3 1.24
SHS C 3. DualGradeĀ® C350L0/C450L0 designed as Grade C450L0
1.05 0.0731 69.7 8.00 134 0.00692 0.692 0.554 0.877 7.20 0.0121 1.06 1.00 10.7 0.877
20 20 2.0 C
x x SHS to AS 1163 is cold-formed, and is therefore allocated the
1.6 0.873 0.0745 85.4 10.5 111 0.00608 0.608 0.474 0.751 7.39 0.0103 0.924 1.00 14.1 0.751 CF residual stresses classification in AS 4100.
SHS C
4. LiteOil and NoKote are available in all sections on request.
b y
n
x x
d
t
n y
Smorgon Steel Tube Mills A.B.N. 22 010 469 977. PO Box 246 Sunnybank, Queensland 4109 Australia Telephone +61 7 3246 2600 Facsimile +61 7 3246 2660 E-mail tubemills@smorgonsteel.com.au Internet www.smorgonsteel.com.au/tubemills
DECEMBER 2006 2-30
Structural SHS DualGradeĀ® ā? Mass & Bundling calculated in accordance with AS 1163
Dimensions Bundling Mass
Bundle Configuration (mm) Bundle Dimensions (mm)
Designation Lengths Metres Nominal Mass Per Bundle
Per Bundle Per Bundle Mass tonnes
6.5 8.0 9.0 12.0 6.5 8.0 9.0 12.0
d b t
6.5 8.0 9.0 12.0 6.5 8.0 9.0 12.0 6.5 8.0 9.0 12.0
mm mm mm WxH WxH WxH WxH Wx H Wx H Wx H Wx H kg/m m/t
1 1 1
SHS SHS SHS
13 13 1.8 12 8 156 104 96 624 0.568 1760 0.354
x x SHS* - - - - - - - - - - - - - - - 2 2 2
DualGradeĀ® DualGradeĀ® DualGradeĀ®
15 15 1.8 10 10 150 150 100 650 0.681 1470 0.442
x x SHS* - - - - - - - - - - - - - - - 3 3 3
SupaGalĀ® KleenKoteĀ® LiteOil
10 10 200 200 100 650 0.873 1150 0.567
20 20 1.6 - - - - - - - - - - - - - - -
x x SHS
2.0 10 10 200 200 100 650 1.05 953 0.682
SHS - - - - - - - - - - - - - - -
10 10 250 250 100 650 1.12 890 0.731
25 25 1.6 - - - - - - - - - - - - - - -
x x SHS
Notes:
2.0 10 10 250 250 100 650 1.36 733 0.886
SHS - - - - - - - - - - - - - - -
1. W = quantity along width of bundle cross-section;
2.5 10 10 250 250 100 650 1.64 610 1.070
SHS - - - - - - - - - - - - - - -
H = quantity along height of bundle cross-section.
3.0 10 10 250 250 100 650 1.89 529 1.230
SHS - - - - - - - - - - - - - - -
2. * Complies with PTMA 9701.
10 10 300 300 100 800 1.38 727 1.100
30 30 1.6 - - - - - - - - - - - - - - -
x x SHS
3. LiteOil and NoKote are available in all sections on request.
2.0 10 10 300 300 100 800 1.68 596 1.340
SHS - - - - - - - - - - - - - - -
2.5 10 10 300 300 100 800 2.03 492 1.630
SHS - - - - - - - - - - - - - - -
3.0 8 8 240 240 64 512 2.36 423 1.210
SHS - - - - - - - - - - - - - - -
10 10 350 350 100 800 1.63 615 1.300
35 35 1.6 - - - - - - - - - - - - - - -
x x SHS
2.0 10 10 350 350 100 800 1.99 502 1.590
SHS - - - - - - - - - - - - - -
2.5 8 8 280 280 64 512 2.42 412 1.240
SHS - - - - - - - - - - - - - - -
3.0 8 8 280 280 64 512 2.83 353 1.450
SHS - - - - - - - - - - - - - - -
b y
n
x x
d
t
n y
Smorgon Steel Tube Mills A.B.N. 22 010 469 977. PO Box 246 Sunnybank, Queensland 4109 Australia Telephone +61 7 3246 2600 Facsimile +61 7 3246 2660 E-mail tubemills@smorgonsteel.com.au Internet www.smorgonsteel.com.au/tubemills
DECEMBER 2006 2-31
PART 0 PART 9
PART 1 PART 2 PART 3 PART 4 PART 5 PART 6 PART 7 PART 8
Quick Reference Product Material Safety
General Information Structural Products Piping Products Other Products Steel Grades Mill Finishes Mill Processing Fabrication
Availability Guide Data Sheets (MSDS)
Structural SHS DualGradeĀ® ā? Mass & Bundling calculated in accordance with AS 1163
Dimensions Bundling Mass
Bundle Configuration (mm) Bundle Dimensions (mm)
Designation Lengths Metres Nominal Mass Per Bundle
Per Bundle Per Bundle Mass tonnes
6.5 8.0 9.0 12.0 6.5 8.0 9.0 12.0
d b t
6.5 8.0 9.0 12.0 6.5 8.0 9.0 12.0 6.5 8.0 9.0 12.0
mm mm mm WxH WxH WxH WxH Wx H Wx H Wx H Wx H kg/m m/t
1 1 1
SHS SHS SHS
9 9 360 360 81 648 1.88 533 1.220
40 40 1.6 - - - - - - - - - - - - - - -
x x SHS 2 2 2
DualGradeĀ® DualGradeĀ® DualGradeĀ®
2.0 9 9 360 360 81 648 2.31 434 1.490
SHS - - - - - - - - - - - - - - - 3 3 3
SupaGalĀ® KleenKoteĀ® LiteOil
2.5 8 8 320 320 64 512 2.82 355 1.440
SHS - - - - - - - - - - - - - - -
3.0 8 8 320 320 64 512 3.30 303 1.690
SHS - - - - - - - - - - - - - - -
4.0 7 7 280 280 49 392 4.09 244 1.600
SHS - - - - - - - - - - - - - - -
Notes:
8 8 400 400 64 512 2.38 420 1.220
50 50 1.6 - - - - - - - - - - - - - - -
x x SHS
1. W = quantity along width of bundle cross-section;
2.0 8 8 400 400 64 512 2.93 341 1.500
SHS - - - - - - - - - - - - - - -
H = quantity along height of bundle cross-section.
2.5 7 7 350 350 49 392 3.60 278 1.410
SHS - - - - - - - - - - - - - - -
2. LiteOil and NoKote are available in all sections on request.
3.0 7 7 350 350 49 392 4.25 236 1.660
SHS - - - - - - - - - - - - - - -
4.0 6 6 300 300 36 288 5.35 187 1.540
SHS - - - - - - - - - - - - - - -
5.0 5 6 250 300 30 240 6.39 156 1.530
SHS - - - - - - - - - - - - - - -
6.0 5 5 250 250 25 200 7.32 137 1.460
SHS - - - - - - - - - - - - - - -
7 7 455 455 49 392 3.13 319 1.230
65 65 1.6 - - - - - - - - - - - - - - -
x x SHS
2.0 6 7 390 455 42 336 3.88 258 1.300
SHS - - - - - - - - - - - - - - -
2.5 6 7 390 455 42 336 4.78 209 1.610
SHS - - - - - - - - - - - - - - -
3.0 6 6 390 390 36 288 5.66 177 1.630
SHS - - - - - - - - - - - - - - -
4.0 5 6 325 390 30 240 7.23 138 1.740
SHS - - - - - - - - - - - - - - -
5.0 5 5 325 325 25 200 8.75 114 1.750
SHS - - - - - - - - - - - - - - -
6.0 4 5 260 325 20 160 10.1 98.6 1.620
SHS - - - - - - - - - - - - - - -
5 6 375 450 30 240 4.50 222 1.080
75 75 2.0 - - - - - - - - - - - - - - -
x x SHS
2.5 5 6 375 450 30 240 5.56 180 1.340
SHS - - - - - - - - - - - - - - -
3.0 5 6 375 450 30 240 6.60 152 1.580
SHS - - - - - - - - - - - - - - -
3.5 5 5 375 375 25 200 7.53 133 1.510
SHS - - - - - - - - - - - - - - -
4.0 5 5 375 375 25 200 8.49 118 1.700
SHS - - - - - - - - - - - - - - -
5.0 4 5 300 375 20 160 10.3 96.9 1.650
SHS - - - - - - - - - - - - - - -
6.0 4 4 300 300 16 128 12.0 83.1 1.540
SHS - - - - - - - - - - - - - - -
b y
n
x x
d
t
n y
Smorgon Steel Tube Mills A.B.N. 22 010 469 977. PO Box 246 Sunnybank, Queensland 4109 Australia Telephone +61 7 3246 2600 Facsimile +61 7 3246 2660 E-mail tubemills@smorgonsteel.com.au Internet www.smorgonsteel.com.au/tubemills
DECEMBER 2006 2-32
Structural SHS DualGradeĀ® ā? Mass & Bundling calculated in accordance with AS 1163
Dimensions Bundling Mass
Bundle Configuration (mm) Bundle Dimensions (mm)
Designation Lengths Metres Nominal Mass Per Bundle
Per Bundle Per Bundle Mass tonnes
6.5 8.0 9.0 12.0 6.5 8.0 9.0 12.0
d b t
6.5 8.0 9.0 12.0 6.5 8.0 9.0 12.0 6.5 8.0 9.0 12.0
mm mm mm WxH WxH WxH WxH Wx H Wx H Wx H Wx H kg/m m/t
1 1 1
SHS SHS SHS
4 5 356 445 20 160 5.38 186 0.861
89 89 x 2.0 SHS - - - - - - - - - - - - - - -
x 2 2 2
DualGradeĀ® DualGradeĀ® DualGradeĀ®
3.5 SHS 4 5 356 445 20 160 9.07 110 1.450
- - - - - - - - - - - - - - - 3 3 3
SupaGalĀ® KleenKoteĀ® LiteOil
5.0 SHS 4 4 356 356 16 128 12.5 79.9 1.600
- - - - - - - - - - - - - - -
6.0 SHS 3 4 267 356 12 96 14.7 68.2 1.410
- - - - - - - - - - - - - - -
4 5 400 500 20 160 7.53 133 1.200
100 100 x 2.5 SHS - - - - - - - - - - - - - - -
x
Notes:
3.0 SHS 4 5 4 4 400 500 400 400 20 16 160 192 8.89 112 1.420 1.710
- - - - - - - - - -
1. W = quantity along width of bundle cross-section;
4.0 SHS 4 4 4 3 400 400 400 300 16 12 128 144 11.6 86.0 1.490 1.670
- - - - - - - - - -
H = quantity along height of bundle cross-section.
5.0 SHS 4 3 3 3 400 300 300 300 12 9 96 108 14.2 70.2 1.370 1.540
- - - - - - - - - -
2. LiteOil and NoKote are available in all sections on request.
6.0 SHS 4 3 3 3 400 300 300 300 12 9 96 108 16.7 59.7 1.610 1.810
- - - - - - - - - -
8.0 SHS 3 3 2 3 300 300 200 300 9 6 72 72 21.4 46.8 1.540 1.540
- - - - - - - - - -
9.0 SHS 3 3 2 3 300 300 200 300 9 6 72 72 23.5 42.5 1.690 1.690
- - - - - - - - - -
10.0 SHS 2 3 200 300 6 72 25.6 39.1 1.840
- - - - - - - - - - - - - - -
3 4 3 3 375 500 375 375 12 9 96 108 14.8 67.7 1.420 1.590
125 125 x 4.0 SHS - - - - - - - - - -
x
5.0 SHS 3 4 3 3 375 500 375 375 12 9 96 108 18.2 55.0 1.740 1.960
- - - - - - - - - -
6.0 SHS 3 3 2 3 375 375 250 375 9 6 72 72 21.4 46.6 1.540 1.540
- - - - - - - - - -
8.0 SHS 2 3 2 2 250 375 250 250 6 4 48 48 27.7 36.1 1.330 1.330
- - - - - - - - - -
9.0 SHS 2 4 2 2 250 500 250 250 8 4 64 48 30.6 32.7 1.960 1.470
- - - - - - - - - -
10.0 SHS 2 2 250 250 4 48 33.4 29.9 1.600
- - - - - - - - - - - - - - -
3 3 2 3 450 450 300 450 9 6 72 72 22.1 45.3 1.590 1.590
150 150 x 5.0 SHS - - - - - - - - - -
x
6.0 SHS 2 3 2 3 300 450 300 450 6 6 48 72 26.2 38.2 1.260 1.880
- - - - - - - - - -
8.0 SHS 2 3 2 2 300 450 300 300 6 4 48 48 33.9 29.5 1.630 1.630
- - - - - - - - - -
9.0 SHS 2 3 2 2 300 450 300 300 6 4 48 48 37.7 26.6 1.810 1.810
- - - - - - - - - -
10.0 SHS 1 2 150 300 2 24 41.3 24.2 0.990
- - - - - - - - - - - - - - -
b y
n
x x
d
t
n y
Smorgon Steel Tube Mills A.B.N. 22 010 469 977. PO Box 246 Sunnybank, Queensland 4109 Australia Telephone +61 7 3246 2600 Facsimile +61 7 3246 2660 E-mail tubemills@smorgonsteel.com.au Internet www.smorgonsteel.com.au/tubemills
DECEMBER 2006 2-33
PART 0 PART 9
PART 1 PART 2 PART 3 PART 4 PART 5 PART 6 PART 7 PART 8
Quick Reference Product Material Safety
General Information Structural Products Piping Products Other Products Steel Grades Mill Finishes Mill Processing Fabrication
Availability Guide Data Sheets (MSDS)
Structural SHS DualGradeĀ® ā? Mass & Bundling calculated in accordance with AS 1163
Dimensions Bundling Mass
Bundle Configuration (mm) Bundle Dimensions (mm)
Designation Lengths Metres Nominal Mass Per Bundle
Per Bundle Per Bundle Mass tonnes
6.5 8.0 9.0 12.0 6.5 8.0 9.0 12.0
d b t
6.5 8.0 9.0 12.0 6.5 8.0 9.0 12.0 6.5 8.0 9.0 12.0
mm mm mm WxH WxH WxH WxH Wx H Wx H Wx H Wx H kg/m m/t
1 1 1
SHS SHS SHS
2 3 2 2 400 600 400 400 6 4 48 48 29.9 33.4 1.440 1.440
200 200 x 5.0 SHS - - - - - - - - - -
x 2 2 2
DualGradeĀ® DualGradeĀ® DualGradeĀ®
6.0 SHS 2 2 2 2 400 400 400 400 4 4 32 48 35.6 28.1 1.140 1.710
- - - - - - - - - - 3 3 3
SupaGalĀ® KleenKoteĀ® LiteOil
8.0 SHS 2 2 1 2 400 400 200 400 4 2 32 24 46.5 21.5 1.490 1.120
- - - - - - - - - -
9.0 SHS 2 2 1 2 400 400 200 400 4 2 32 24 51.8 19.3 1.660 1.240
- - - - - - - - - -
10.0 SHS 1 2 200 400 2 24 57.0 17.6 1.370
- - - - - - - - - - - - - - -
Notes:
12.5 SHS 1 2 200 400 2 24 69.4 14.4 1.670
- - - - - - - - - - - - - - -
1. W = quantity along width of bundle cross-section;
16.0 SHS 1 1 200 200 1 12 85.5 11.7 1.030
- - - - - - - - - - - - - - -
H = quantity along height of bundle cross-section.
2 2 1 2 500 500 250 500 4 2 32 24 45.0 22.2 1.440 1.080
250 250 x 6.0 SHS - - - - - - - - - -
x
2. LiteOil and NoKote are available in all sections on request.
8.0 SHS 2 2 1 2 500 500 250 500 4 2 32 24 59.1 16.9 1.890 1.420
- - - - - - - - - -
9.0 SHS 1 2 1 2 250 500 250 500 2 2 16 24 65.9 15.2 1.050 1.580
- - - - - - - - - -
10.0 SHS 1 2 250 500 2 24 72.7 13.8 1.740
- - - - - - - - - - - - - - -
12.5 SHS 1 1 250 250 1 12 89.0 11.2 1.070
- - - - - - - - - - - - - - -
16.0 SHS 1 1 250 250 1 12 111 9.04 1.330
- - - - - - - - - - - - - - -
1 1 300 300 1 12 71.6 14.0 0.860
300 300 x 8.0 SHS - - - - - - - - - - - - - - -
x
10.0 SHS 1 1 300 300 1 12 88.4 11.3 1.060
- - - - - - - - - - - - - - -
12.5 SHS 1 1 300 300 1 12 109 9.21 1.300
- - - - - - - - - - - - - - -
16.0 SHS 1 1 300 300 1 12 136 7.36 1.630
- - - - - - - - - - - - - - -
1 1 350 350 1 12 84.2 11.9 1.010
350 350 x 8.0 SHS - - - - - - - - - - - - - - -
x
10.0 SHS 1 1 350 350 1 12 104 9.61 1.250
- - - - - - - - - - - - - - -
12.5 SHS 1 1 350 350 1 12 128 7.80 1.540
- - - - - - - - - - - - - - -
16.0 SHS 1 1 350 350 1 12 161 6.21 1.930
- - - - - - - - - - - - - - -
1 1 400 400 1 12 120 8.35 1.440
400 400 x 10.0 SHS - - - - - - - - - - - - - - -
x
12.5 SHS 1 1 400 400 1 12 148 6.76 1.770
- - - - - - - - - - - - - - -
16.0 SHS 1 1 400 400 1 12 186 5.38 2.230
- - - - - - - - - - - - - - -
b y
n
x x
d
t
n y
Smorgon Steel Tube Mills A.B.N. 22 010 469 977. PO Box 246 Sunnybank, Queensland 4109 Australia Telephone +61 7 3246 2600 Facsimile +61 7 3246 2660 E-mail tubemills@smorgonsteel.com.au Internet www.smorgonsteel.com.au/tubemills
DECEMBER 2006 2-34
RHS Grade C350L0 ā? Specifications
Technical Specifications KleenKoteĀ® Finish Non-Standard Lengths
Australian Standards RHS Grade C350L0 with KleenKoteĀ® finish is supplied Special orders of non-standard pack lengths of RHS
in the following surface colours: Grade C350L0 are available (conditions apply). Check
RHS Grade C350L0 is manufactured and tested to
comply with the requirements of the with your distributor for details.
Blue Black
1
1 RHS RHS
following specifications: This primer paint finish is applied in-line using the 2
2 C350L0 C350L0
Minimum Length: 3
3 SupaGalĀ® KleenKoteĀ®
AS 1163 ā? Structural Steel Hollow Section patented KleenKoteĀ® process and is supplied in the
(Grade C350L0). (50x25 ā? 75x25 RHS) SupaGalĀ®/KleenKoteĀ® ___4.2 m
following coating thicknesses:
AS/NZS 4792 ā? Hot-dip galvanized (zinc) coatings
Maximum Length:
Blue & Black _______________ Target 12 microns with
General Description
on ferrous hollow sections, applied by a continuous
average at 8-10 microns (50x25 RHS) SupaGalĀ®/KleenKoteĀ® __________ 8.0 m
or a specialized process (Section 3).
Manufacturing Process
Note: Non-standard finishes, such as NoKote, are
Mechanical Properties (65x35 ā? 75x25 RHS) SupaGalĀ®/KleenKoteĀ® __12.2 m
RHS Grade C350L0, for manufacturing, general
available if ordered prior to rollings. Conditions apply.
Note: Contact your Smorgon Steel Tube Mills
RHS Grade C350L0 has the following mechanical fabrication and lighter structural applications, is
Refer to manufacturer for details.
properties: manufactured by cold-forming and high frequency
representative for lengths outside this range.
See Quick Reference Product Availability Guide (Part 0) Electric Resistance Welding (ERW) of higher strength
350 MPa
Minimum Yield Strength _________________
Thickness steel strip. The cold-forming process enhances
for further information on availability.
Minimum Tensile Strength ______________ 430 MPa
_
the strength, hardness and surface finish of the tube
Minimum Elongation in 5.65āSo ______________ 16%
LiteOil Finish RHS Grade C350L0 is available in 1.6 mm to 4.0 mm wall and produces product to tight dimensional tolerances.
L0 __ guaranteed impact properties at 0Ā°C to AS 1163
_ thicknesses. These thicknesses are identified by the
Further Information
LiteOil tubular products use a light oil coating which
Tolerances following end colour codes:
is the standard finish for medium to large sized RHS. For further information refer to the Smorgon Steel Tube Mills:
Tolerances for RHS Grade C350L0 are compliant with _________________________________ Purple
See Quick Reference Product Availability Guide (Part 0) 1.6 mm
Product Solutions Guide.
AS 1163. See Dimensional Tolerances in Part 1 for
for further information on availability. _________________________________ Yellow
2.0 mm
more information.
End Finish (Mill Processing) ___________________________________ Pink
2.5 mm
Supply Conditions
___________________________________ Blue
3.0 mm
SupaGalĀ® Finish Plain Ends only.
_________________________________ Green
4.0 mm
Standard Lengths
RHS Grade C350L0 with SupaGalĀ® finish is
Mass & Bundling
manufactured using steel strip that has the Standard lengths for RHS Grade C350L0:
following coating thickness:
8.0 m Mass & bundling data for the RHS Grade C350L0 range
Ā®/KleenKoteĀ® ___
(50x25 ā? 75x25 RHS) SupaGal
100 g/m2 each side
Minimum coating mass ________
is the same as for RHS DualGradeĀ® C350L0/C450L0.
This may exclude some wall thicknesses and finishes.
Designated as __________ AS/NZS 4792 ZB 100/100
Refer to Structural Products (Part 2), page 2-21, in this
Contact your Smorgon Steel Tube Mills representative
See Quick Reference Product Availability Guide (Part 0)
for further information on availability. for further details. Product Manual for further information.
Smorgon Steel Tube Mills A.B.N. 22 010 469 977. PO Box 246 Sunnybank, Queensland 4109 Australia Telephone +61 7 3246 2600 Facsimile +61 7 3246 2660 E-mail tubemills@smorgonsteel.com.au Internet www.smorgonsteel.com.au/tubemills
DECEMBER 2006 2-35
PART 0 PART 9
PART 1 PART 2 PART 3 PART 4 PART 5 PART 6 PART 7 PART 8
Quick Reference Product Material Safety
General Information Structural Products Piping Products Other Products Steel Grades Mill Finishes Mill Processing Fabrication
Availability Guide Data Sheets (MSDS)
RHS Grade C350L0 ā? Section Properties calculated to AS 1163 in accordance with AS 4100
Properties for Design to AS 4100
Dimensions and Ratios Properties
External Gross
Torsion Torsion Form
Designation Surface Section About x-axis About y-axis About x-axis About y-axis
Mass Constant Modulus Factor
b-2t d-2t
Area Area
per m Compact- Compact-
Ī»e Ī»e
d b t per m per t Ag Ix Zx Sx rx Iy Zy Sy ry J C kf Zex Zey
t t ness ness
1
1 RHS RHS
106mm4 103mm3 103mm3 mm 106mm4 103mm3 103mm3 mm 106mm4 103mm3 (C,N,S) 103mm3 (C,N,S) 103mm3
m2/m m2/t mm2
mm mm mm kg/m
2
2 C350L0 C350L0
3.60 0.191 53.1 8.00 28.0 459 0.285 7.60 10.1 24.9 0.0487 3.89 4.53 10.3 0.144 7.14 1.00 9.47 10.1 33.1 4.33
75 25 2.5 C N
x x RHS 3
3 SupaGalĀ® KleenKoteĀ®
2.0 2.93 0.193 65.8 10.5 35.5 374 0.238 6.36 8.31 25.3 0.0414 3.31 3.77 10.5 0.120 6.04 0.964 12.4 8.31 42.0 3.18
RHS C S
1.6 2.38 0.195 81.7 13.6 44.9 303 0.197 5.26 6.81 25.5 0.0347 2.78 3.11 10.7 0.0993 5.05 0.813 16.1 6.81 53.1 2.22
RHS C S
5.35 0.183 34.2 6.75 14.3 681 0.328 10.1 13.3 22.0 0.123 7.03 8.58 13.4 0.320 12.5 1.00 7.99 13.3 16.9 8.58
65 35 4.0 C C
x x RHS Notes:
3.0 4.25 0.190 44.7 9.67 19.7 541 0.281 8.65 11.0 22.8 0.106 6.04 7.11 14.0 0.259 10.4 1.00 11.4 11.0 23.3 7.11
RHS C C 1. For Grade C350L0: fy = 350 MPa
2.5 3.60 0.191 53.1 12.0 24.0 459 0.244 7.52 9.45 23.1 0.0926 5.29 6.13 14.2 0.223 9.10 1.00 14.2 9.45 28.4 6.13
RHS C C and fu = 430 MPa; fy = yield stress used in design;
2.0 2.93 0.193 65.8 15.5 30.5 374 0.204 6.28 7.80 23.4 0.0778 4.44 5.07 14.4 0.184 7.62 1.00 18.3 7.80 36.1 4.69
RHS C N fu = tensile strength used in design; as defined in AS 4100
3.07 0.140 45.5 6.33 14.7 391 0.112 4.47 5.86 16.9 0.0367 2.93 3.56 9.69 0.0964 5.18 1.00 7.49 5.86 17.4 3.56
50 25 3.0 C C
x x RHS 2. C = Compact Section; N = Non-Compact Section;
2.5 2.62 0.141 54.0 8.00 18.0 334 0.0989 3.95 5.11 17.2 0.0328 2.62 3.12 9.91 0.0843 4.60 1.00 9.47 5.11 21.3 3.12
RHS C C S = Slender Section (as defined in AS 4100).
2.0 2.15 0.143 66.6 10.5 23.0 274 0.0838 3.35 4.26 17.5 0.0281 2.25 2.62 10.1 0.0706 3.92 1.00 12.4 4.26 27.2 2.62
RHS C C 3. Grade C350L0 to AS 1163 is cold-formed, and is therefore
1.6 1.75 0.145 82.5 13.6 29.3 223 0.0702 2.81 3.53 17.7 0.0237 1.90 2.17 10.3 0.0585 3.29 1.00 16.1 3.53 34.6 2.05
RHS C N allocated the CF residual stresses classification in AS 4100.
4. LiteOil and NoKote are available in all sections on request.
5. For Mass & Bundling data see listings in RHS DualGradeĀ®
C350L0/C450L0 (Part 2 of this Product Manual).
b y
t d x x
y
Smorgon Steel Tube Mills A.B.N. 22 010 469 977. PO Box 246 Sunnybank, Queensland 4109 Australia Telephone +61 7 3246 2600 Facsimile +61 7 3246 2660 E-mail tubemills@smorgonsteel.com.au Internet www.smorgonsteel.com.au/tubemills
DECEMBER 2006 2-36
SHS Grade C350L0 ā? Specifications
Technical Specifications KleenKoteĀ® Finish Non-Standard Lengths
Australian Standards SHS Grade C350L0 with KleenKoteĀ® finish Special orders of non-standard pack lengths of
is supplied in the following surface colours: SHS Grade C350L0 are available (conditions apply).
SHS Grade C350L0 is manufactured and tested to
Check with your distributor for details.
comply with the requirements of the Blue Black
1 1
SHS SHS
following specifications: This primer paint finish is applied in-line using the Minimum Length: 2 2
C350L0 C350L0
AS 1163 ā? Structural Steel Hollow Section patented KleenKoteĀ® process and is supplied in the 3 3
SupaGalĀ® KleenKoteĀ®
(20x20 ā? 50x50 SHS) SupaGalĀ®/KleenKoteĀ® __ 4.2 m
_
(Grade C350L0) following coating thicknesses:
Maximum Length:
AS/NZS 4792 ā? Hot-dip galvanized (zinc) coatings
Blue & Black _______________ Target 12 microns with
General Description
on ferrous hollow sections, applied by a continuous (20x20 ā? 50x50 SHS) SupaGalĀ®/KleenKoteĀ® __ 8.0 m
_
average at 8-10 microns
or a specialized process (Section 3).
Manufacturing Process
12.0m
(50x50 SHS) SupaGal/KleenKote ___________
Note: Non-standard finishes, such as NoKote, are
Mechanical Properties Note: Contact your Smorgon Steel Tube Mills
available if ordered prior to rollings. Conditions apply. SHS Grade C350L0, for manufacturing, general
SHS Grade C350L0 has the following representative for lengths outside this range. fabrication and lighter structural applications, is
Refer to manufacturer for details.
mechanical properties: manufactured by cold-forming and high frequency
See Quick Reference Product Availability Guide (Part 0) Thickness Electric Resistance Welding (ERW) of higher strength
350 MPa
Minimum Yield Strength _________________
for further information on availability.
steel strip. The cold-forming process enhances the
Minimum Tensile Strength ______________ 430 MPa SHS Grade C350L0 is available in 1.6 mm to 5.0 mm
_
LiteOil Finish strength, hardness and surface finish of the tube and
Minimum Elongation in 5.65āSo ______________ 16% wall thicknesses. These thicknesses are identified by
produces product to tight dimensional tolerances.
L0 __ guaranteed impact properties at 0Ā°C to AS 1163
_ the following end colour codes:
LiteOil tubular products use a light oil coating which
Further Information
is the standard finish for medium to large sized SHS.
Tolerances _________________________________ Purple
1.6 mm
For further information refer to the Smorgon Steel Tube Mills:
See Quick Reference Product Availability Guide (Part 0) _________________________________ Brown
Tolerances for SHS Grade C350L0 are compliant with 1.8 mm
for further information on availability. Product Solutions Guide.
AS 1163. See Dimensional Tolerances in Part 1 for _________________________________ Yellow
2.0 mm
more information.
End Finish (Mill Processing) ___________________________________ Pink
2.5 mm
Supply Conditions ___________________________________ Blue
3.0 mm
Plain Ends only.
SupaGalĀ® Finish _________________________________ Green
4.0 mm
Standard Lengths
________________________________ Orange
5.0 mm
SHS Grade C350L0 with SupaGalĀ® finish is
Standard lengths for SHS Grade C350L0:
manufactured using steel strip that has the following Mass & Bundling
(13x13 ā? 25x25 SHS) Grade C350L0/KleenKoteĀ®_6.5 m
coating thickness:
Mass & bundling data for the SHS Grade C350L0 range
Ā®_8.0 m
100 g/m2 each side (30x30 ā? 50x50 SHS) Grade C350L0/KleenKote
Minimum coating mass ________
is the same as for SHS DualGradeĀ® C350L0/C450L0.
This may exclude some wall thicknesses and finishes.
Designated as __________ AS/NZS 4792 ZB 100/100
Refer to Structural Products (Part 2), page 2-31 and
Contact your Smorgon Steel Tube Mills representative
See Quick Reference Product Availability Guide (Part 0)
2-32, in this Product Manual for further information.
for further information on availability. for further details.
Smorgon Steel Tube Mills A.B.N. 22 010 469 977. PO Box 246 Sunnybank, Queensland 4109 Australia Telephone +61 7 3246 2600 Facsimile +61 7 3246 2660 E-mail tubemills@smorgonsteel.com.au Internet www.smorgonsteel.com.au/tubemills
DECEMBER 2006 2-37
PART 0 PART 9
PART 1 PART 2 PART 3 PART 4 PART 5 PART 6 PART 7 PART 8
Quick Reference Product Material Safety
General Information Structural Products Piping Products Other Products Steel Grades Mill Finishes Mill Processing Fabrication
Availability Guide Data Sheets (MSDS)
SHS Grade C350L0 ā? Section Properties calculated to AS 1163 in accordance with AS 4100
Properties for Design to AS 4100
Dimensions and Ratios Section Properties
External Gross
Torsion Torsion Form
Mass About x and y-axis
Designation Surface Section About x-, y- and n-axis Constant Modulus Factor
per b-2t
Area Area Compact-
m
Ī»e
d b t per m per t Ag Ix Zx Zn Sx rx J C kf Zex
t ness
10 6 mm4 10 3 mm 3 10 3 mm 3 10 3 mm 3 10 6 mm4 10 3 mm 3 10 3 mm 3 1 1
m 2 /m m 2 /t mm 2
mm mm mm kg/m mm (C,N,S) SHS SHS
2 2
C350L0 C350L0
6.39 0.179 27.9 8.00 814 0.257 10.3 8.51 13.2 17.8 0.469 16.3 1.00 9.47 13.2
50 50 5.0 C
x x SHS 3 3
SupaGalĀ® KleenKoteĀ®
4.0 5.35 0.183 34.2 10.5 681 0.229 9.15 7.33 11.4 18.3 0.403 14.3 1.00 12.4 11.4
SHS C
3.0 4.25 0.190 44.7 14.7 541 0.195 7.79 5.92 9.39 19.0 0.321 11.8 1.00 17.4 9.39
SHS C
2.5 3.60 0.191 53.1 18.0 459 0.169 6.78 5.09 8.07 19.2 0.275 10.2 1.00 21.3 8.07
SHS C
Notes:
2.0 2.93 0.193 65.8 23.0 374 0.141 5.66 4.20 6.66 19.5 0.226 8.51 1.00 27.2 6.66
SHS C
1. For Grade C350L0: fy = 350 MPa
1.6 2.38 0.195 81.7 29.3 303 0.117 4.68 3.44 5.46 19.6 0.185 7.03 1.00 34.6 5.10
SHS N
and fu = 430 MPa; fy = yield stress used in design;
4.09 0.143 34.9 8.00 521 0.105 5.26 4.36 6.74 14.2 0.192 8.33 1.00 9.47 6.74
40 40 4.0 C
x x SHS fu = tensile strength used in design; as defined in AS 4100
3.0 3.30 0.150 45.3 11.3 421 0.0932 4.66 3.61 5.72 14.9 0.158 7.07 1.00 13.4 5.72
SHS C
2. C = Compact Section; N = Non-Compact Section;
2.5 2.82 0.151 53.7 14.0 359 0.0822 4.11 3.13 4.97 15.1 0.136 6.21 1.00 16.6 4.97
SHS C S = Slender Section (as defined in AS 4100).
2.0 2.31 0.153 66.4 18.0 294 0.0694 3.47 2.61 4.13 15.4 0.113 5.23 1.00 21.3 4.13
SHS C
3. Grade C350L0 to AS 1163 is cold-formed, and is therefore
1.6 1.88 0.155 82.3 23.0 239 0.0579 2.90 2.15 3.41 15.6 0.0927 4.36 1.00 27.2 3.41
SHS C allocated the CF residual stresses classification in AS 4100.
2.83 0.130 45.8 9.67 361 0.0595 3.40 2.67 4.23 12.8 0.102 5.18 1.00 11.4 4.23
35 35 3.0 C
x x SHS 4. LiteOil and NoKote are available in all sections on request.
2.5 2.42 0.131 54.2 12.0 309 0.0529 3.02 2.33 3.69 13.1 0.0889 4.58 1.00 14.2 3.69
SHS C
5. For Mass & Bundling data see listings in SHS DualGradeĀ®
2.0 1.99 0.133 66.8 15.5 254 0.0451 2.58 1.95 3.09 13.3 0.0741 3.89 1.00 18.3 3.09
SHS C C350L0/C450L0 (Part 2 of this Product Manual).
1.6 1.63 0.135 82.7 19.9 207 0.0379 2.16 1.62 2.57 13.5 0.0611 3.26 1.00 23.5 2.57
SHS C
2.36 0.110 46.5 8.00 301 0.0350 2.34 1.87 2.96 10.8 0.0615 3.58 1.00 9.47 2.96
30 30 3.0 C
x x SHS
2.5 2.03 0.111 54.8 10.0 259 0.0316 2.10 1.65 2.61 11.0 0.0540 3.20 1.00 11.8 2.61
SHS C
2.0 1.68 0.113 67.4 13.0 214 0.0272 1.81 1.39 2.21 11.3 0.0454 2.75 1.00 15.4 2.21
SHS C
1.6 1.38 0.115 83.3 16.8 175 0.0231 1.54 1.16 1.84 11.5 0.0377 2.32 1.00 19.8 1.84
SHS C
1.89 0.0897 47.4 6.33 241 0.0184 1.47 1.21 1.91 8.74 0.0333 2.27 1.00 7.49 1.91
25 25 3.0 C
x x SHS
2.5 1.64 0.0914 55.7 8.00 209 0.0169 1.35 1.08 1.71 8.99 0.0297 2.07 1.00 9.47 1.71
SHS C
2.0 1.36 0.0931 68.3 10.5 174 0.0148 1.19 0.926 1.47 9.24 0.0253 1.80 1.00 12.4 1.47
SHS C
1.6 1.12 0.0945 84.1 13.6 143 0.0128 1.02 0.780 1.24 9.44 0.0212 1.54 1.00 16.1 1.24
SHS C
1.05 0.0731 69.7 8.00 134 0.00692 0.692 0.554 0.877 7.20 0.0121 1.06 1.00 9.47 0.877
20 20 2.0 C
x x SHS
1.6 0.873 0.0745 85.4 10.5 111 0.00608 0.608 0.474 0.751 7.39 0.0103 0.924 1.00 12.4 0.751
SHS C
15 15 1.8 0.681 0.0538 79.1 6.33 86.7 0.00239 0.318 0.262 0.414 5.25 0.00431 0.491 1.00 7.49 0.414
x x SHS C b y
n
13 13 1.8 0.568 0.0458 80.7 5.22 72.3 0.00142 0.218 0.184 0.290 4.42 0.00262 0.339 1.00 6.18 0.290
x x SHS C
x x
d
t
n y
Smorgon Steel Tube Mills A.B.N. 22 010 469 977. PO Box 246 Sunnybank, Queensland 4109 Australia Telephone +61 7 3246 2600 Facsimile +61 7 3246 2660 E-mail tubemills@smorgonsteel.com.au Internet www.smorgonsteel.com.au/tubemills
DECEMBER 2006 2-38
|