**** SECTION 2 - COMPOSITION, INFORMATION ON INGREDIENTS ****
+----------------+--------------------------------------+----------+-----------+
| CAS# | Chemical Name | % | EINECS# |
|----------------|--------------------------------------|----------|-----------|
| 110-96-3 |Diisobutylamine | 99 | 203-819-3 |
+----------------+--------------------------------------+----------+-----------+
Hazard Symbols: C
Risk Phrases: 10 22 34
**** SECTION 3 - HAZARDS IDENTIFICATION ****
EMERGENCY OVERVIEW
Flammable. Harmful if swallowed. Causes burns.Corrosive.
Potential Health Effects
Eye:
Causes eye burns. May cause chemical conjunctivitis and corneal
damage.
Skin:
Causes skin burns. May cause irritation and dermatitis. May cause
cyanosis of the extremities. May cause skin rash (in milder cases),
and cold and clammy skin with cyanosis or pale color.
Ingestion:
Harmful if swallowed. May cause severe and permanent damage to the
digestive tract. May cause gastrointestinal irritation with nausea,
vomiting and diarrhea. May cause perforation of the digestive tract.
Ingestion of large amounts may cause CNS depression. May cause
systemic effects.
Inhalation:
May cause irritation of the respiratory tract with burning pain in
the nose and throat, coughing, wheezing, shortness of breath and
pulmonary edema. Inhalation may be fatal as a result of spasm,
inflammation, edema of the larynx and bronchi, chemical pneumonitis
and pulmonary edema. Aspiration may lead to pulmonary edema. Vapors
may cause dizziness or suffocation. May cause systemic effects. May
cause burning sensation in the chest.
Chronic:
Effects may be delayed.
**** SECTION 4 - FIRST AID MEASURES ****
Eyes:
Get medical aid immediately. Do NOT allow victim to rub eyes or keep
eyes closed. Extensive irrigation with water is required (at least 30
minutes).
Skin:
Get medical aid immediately. Immediately flush skin with plenty of
water for at least 15 minutes while removing contaminated clothing
and shoes. Wash clothing before reuse. Destroy contaminated shoes.
Ingestion:
Never give anything by mouth to an unconscious person. Get medical
aid immediately. Do NOT induce vomiting and seek IMMEDIATE MEDICAL
ADVICE. Wash mouth out with water.
Inhalation:
Get medical aid immediately. Remove from exposure and move to fresh
air immediately. If not breathing, give artificial respiration. If
breathing is difficult, give oxygen. Do NOT use mouth-to-mouth
resuscitation. If breathing has ceased apply artificial respiration
using oxygen and a suitable mechanical device such as a bag and a
mask.
Notes to Physician:
**** SECTION 5 - FIRE FIGHTING MEASURES ****
General Information:
As in any fire, wear a self-contained breathing apparatus in
pressure-demand, MSHA/NIOSH (approved or equivalent), and full
protective gear. Vapors may form an explosive mixture with air.
Vapors can travel to a source of ignition and flash back. During a
fire, irritating and highly toxic gases may be generated by thermal
decomposition or combustion. Will burn if involved in a fire. Use
water spray to keep fire-exposed containers cool. Water may be
ineffective. Material is lighter than water and a fire may be spread
by the use of water. Containers may explode in the heat of a fire.
Flammable liquid and vapor. Vapors may be heavier than air. They
can spread along the ground and collect in low or confined areas.
Extinguishing Media:
For small fires, use dry chemical, carbon dioxide, water spray or
alcohol-resistant foam. For large fires, use water spray, fog, or
alcohol-resistant foam. Use water spray to cool fire-exposed
containers. Water may be ineffective. Do NOT use straight streams of
water.
**** SECTION 6 - ACCIDENTAL RELEASE MEASURES ****
General Information: Use proper personal protective equipment as indicated
in Section 8.
Spills/Leaks:
Absorb spill with inert material (e.g. vermiculite, sand or earth),
then place in suitable container. Avoid runoff into storm sewers and
ditches which lead to waterways. Clean up spills immediately,
observing precautions in the Protective Equipment section. Remove all
sources of ignition. Use a spark-proof tool. Provide ventilation. A
vapor suppressing foam may be used to reduce vapors.
**** SECTION 7 - HANDLING and STORAGE ****
Handling:
Use only in a well-ventilated area. Ground and bond containers when
transferring material. Use spark-proof tools and explosion proof
equipment. Do not breathe dust, vapor, mist, or gas. Do not get in
eyes, on skin, or on clothing. Empty containers retain product
residue, (liquid and/or vapor), and can be dangerous. Keep container
tightly closed. Keep away from heat, sparks and flame. Do not ingest
or inhale. Discard contaminated shoes. Do not pressurize, cut, weld,
braze, solder, drill, grind, or expose empty containers to heat,
sparks or open flames.
Storage:
Keep away from heat, sparks, and flame. Keep away from sources of
ignition. Store in a cool, dry place. Keep container closed when not
in use. Store in a tightly closed container. Flammables-area.
**** SECTION 8 - EXPOSURE CONTROLS, PERSONAL PROTECTION ****
Engineering Controls:
Facilities storing or utilizing this material should be equipped
with an eyewash facility and a safety shower. Use adequate general or
local explosion-proof ventilation to keep airborne levels to
acceptable levels.
Exposure Limits
CAS# 110-96-3:
Personal Protective Equipment
Eyes:
Wear appropriate protective eyeglasses or chemical
safety goggles as described by OSHA's eye and face
protection regulations in 29 CFR 1910.133 or European
Standard EN166.
Skin:
Wear appropriate protective gloves to prevent skin
exposure.
Clothing:
Wear appropriate protective clothing to prevent skin
exposure.
Respirators:
A respiratory protection program that meets OSHA's 29
CFR 1910.134 and ANSI Z88.2 requirements or European
Standard EN 149 must be followed whenever workplace
conditions warrant respirator use.
**** SECTION 9 - PHYSICAL AND CHEMICAL PROPERTIES ****
Physical State: Clear liquid
Color: APHA: 15 max
Odor: amine-like
pH: Not available.
Vapor Pressure: 7 hPa @ 20 C
Viscosity: 0.8 mPas 20 deg C
Boiling Point: 137 - 139 deg C @ 7mm Hg
Freezing/Melting Point: -77 deg C
Autoignition Temperature: 290 deg C ( 554.00 deg F)
Flash Point: 26 deg C ( 78.80 deg F)
Explosion Limits, lower: .80 vol %
Explosion Limits, upper: 5.70 vol %
Decomposition Temperature:
Solubility in water: 5 G/L WATER (20C)
Specific Gravity/Density: .7400g/cm3
Molecular Formula: ??(CH3)2CHCH2!2NH
Molecular Weight: 129.24
**** SECTION 10 - STABILITY AND REACTIVITY ****
Chemical Stability:
Stable under normal temperatures and pressures.
Conditions to Avoid:
Incompatible materials, ignition sources, excess heat.
Incompatibilities with Other Materials:
Strong oxidizing agents.
Hazardous Decomposition Products:
Nitrogen oxides, carbon monoxide, irritating and toxic fumes and
gases, carbon dioxide.
Hazardous Polymerization: Will not occur.
**** SECTION 11 - TOXICOLOGICAL INFORMATION ****
RTECS#:
CAS# 110-96-3: TX1750000
LD50/LC50:
CAS# 110-96-3: Oral, mouse: LD50 = 629 mg/kg; Oral, rat: LD50 = 258
mg/kg.
Carcinogenicity:
Diisobutylamine -
Not listed by ACGIH, IARC, or NTP.
Other:
See actual entry in RTECS for complete information.
**** SECTION 12 - ECOLOGICAL INFORMATION ****
Other
For more information, see "HANDBOOK OF ENVIRONMENTAL FATE AND
EXPOSURE DATA."
**** SECTION 13 - DISPOSAL CONSIDERATIONS ****
Dispose of in a manner consistent with federal, state, and local regulations.
**** SECTION 14 - TRANSPORT INFORMATION ****
IATA
Shipping Name: DIISOBUTYLAMINE
Hazard Class: 3 (8)
UN Number: 2361
Packing Group: III
IMO
Shipping Name: DIISOBUTYLAMINE
Hazard Class: 3.3 (8)
UN Number: 2361
Packing Group: III
RID/ADR
Shipping Name: DIISOBUTYLAMINE
Hazard Class: 3
UN Number: 2361
Packing group: III
**** SECTION 15 - REGULATORY INFORMATION ****
European/International Regulations
European Labeling in Accordance with EC Directives
Hazard Symbols: C
Risk Phrases:
R 10 Flammable.
R 22 Harmful if swallowed.
R 34 Causes burns.
Safety Phrases:
S 9 Keep container in a well-ventilated place.
S 16 Keep away from sources of ignition - No
smoking.
S 25 Avoid contact with eyes.
S 33 Take precautionary measures against static
discharges.
S 36/37/39 Wear suitable protective clothing, gloves
and eye/face protection.
S 45 In case of accident or if you feel unwell, seek
medical advice immediately (show the label where
possible).
WGK (Water Danger/Protection)
CAS# 110-96-3: No information available.
Canada
CAS# 110-96-3 is listed on Canada's NDSL List.
CAS# 110-96-3 is not listed on Canada's Ingredient Disclosure List.
US FEDERAL
TSCA
CAS# 110-96-3 is listed on the TSCA inventory.
**** SECTION 16 - ADDITIONAL INFORMATION ****
MSDS Creation Date: 9/02/1997 Revision #5 Date: 3/18/2003
The information above is believed to be accurate and represents the best
information currently available to us. However, we make no warranty of
merchantability or any other warranty, express or implied, with respect to
such information, and we assume no liability resulting from its use. Users
should make their own investigations to determine the suitability of the
information for their particular purposes. In no way shall the company be
liable for any claims, losses, or damages of any third party or for lost
profits or any special, indirect, incidental, consequential or exemplary
damages, howsoever arising, even if the company has been advised of
the possibility of such damages.
--------------------------------------------------------------------------------
--------------------------------------------------------------------------------
|
|
|
| ALL MSDS PAGES IN THIS GROUP
| | NAME | CAS |
|
Ethyl 2-aminocyclohepta[b]thiophene-3-carboxylate, 99+%
| 0-01-1 |
|
(1R,2S)-(-)-Ephedrine hydrochloride, 99.0-101.0% (dry subst.)
| 50-98-6 |
|
Ir-125, Laser Grade
| 3599-32-4 |
|
Trimethyl(phenylseleno)silane, tech., ca 90% (gc)
| 3386-17-5 |
|
Guanosine 2'(3')-monophosphate, disodium salt monohydrate, mixed
| 14200-70-5 |
|
Diisobutylamine, 99%
| 110-96-3 |
|
4-Phenolsulfonic acid, sodium salt dihydrate, 99%
| 825-90-1 |
|
(R)-(-)-2-Amino-3-hydroxy-3-methylbutanoic acid
| 2280-48-0 |
|
3,4-Diaminopyridine, 98%
| 54-96-6 |
|
Pentafluorophenol, 99+%
| 771-61-9 |
|
Methyl 2-butynoate, ca 97 %
| 23326-27-4 |
|
Sodium Carbonate Decahydrate, C.P.
| 6132-02-1 |
|
3-Pentanone, 98%
| 96-22-0 |
|
2-Amino-5-Nitrobenzophenone, 98%
| 1775-95-7 |
|
Ethyl Oleate
| 111-62-6 |
|
4-Nitrobenzotrifluoride, 96%
| 402-54-0 |
|
4-Vinyl-1-cyclohexene, 99%,stabilized with 50-200 ppm bht
| 100-40-3 |
|
3-Nitrophenyl Isocyanate (Pract)
| 3320-87-4 |
|
Hydrazine Acetate, 99% (titr.)
| 7335-65-1 |
|
3-Iodoanisole, 97%
| 766-85-8 |
|
Vinyltrimethoxysilane, 98%
| 2768-02-7 |
|
(1S)-Chrysanthemolactone, 99+%
| 14087-71-9 |
|
2,5-Dimethylbenzaldehyde, 96%
| 5779-94-2 |
|
N-Methyl-N-propargylbenzylamine, 97%
| 555-57-7 |
|
2,2-Dichloroacetophenone, 97%
| 2648-61-5 |
|
Tetrabutylammonium fluoride trihydrate, 99%
| 87749-50-6 |
|
Alpha-(4-Pyridyl 1-Oxide)-N-Tert-Butyl-Nitrone, 99%
| 66893-81-0 |
|
2-Mercapto-5-methyl-1,3,4-thiadiazole, 99%
| 29490-19-5 |
|
m-Phenoxytoluene, 98+%
| 3586-14-9 |
|
trans-2-Pentene, 95%
| 646-04-8 |
|
3-Phenylpropionaldehyde, 97% (GC)
| 104-53-0 |
|
4-Nitro-2,1,3-benzothiadiazole
| 6583-06-8 |
|
(2-Hydroxybenzyl)triphenylphosphonium bromide, 98%
| 70340-04-4 |
|
2-Amino-6-Fluorobenzothiazole, 99%
| 348-40-3 |
|
R(-)-1,3-Butanediol, 98%
| 6290-03-5 |
|
Dextrin (Techn)
| 9004-53-9 |
|
3-(4-Dimethylamino-1-Naphthylazo)-4-Methoxybenzenesulfonic Acid, 98%
| 62758-14-9 |
|
1-Propanesulfonic Acid, 95% (Titr.)
| 5284-66-2 |
|
1,10-Dichlorodecane, 98%
| 2162-98-3 |
|
Dibutyl sebacate, 93%
| 109-43-3 |
|
Boron trifluoride-propanol 14% bf3 w/v in propanol
| 71-23-8 |
|
Cesium Bicarbonate
| 15519-28-5 |
|
2,4-Dihydroxypyrimidine-5-Carboxylic Acid Hydrate, 98%
| 23945-44-0 |
|
cis-2-Methylcyclohexanol, 99+%
| 7443-70-1 |
|
2-Methyl-5-tert-butylthiophenol, 93% remainder isomer
| 7340-90-1 |
|
Erucylamide , tech., 90% (gc)
| 112-84-5 |
|
2-Bromo-4-fluoroanisole, 98%
| 452-08-4 |
|
Triphenylphosphine oxide, 99%
| 791-28-6 |
|
5,10,15,20-Tetrakis(Pentafluorophenyl)- 21h,23h-Porphine
| 25440-14-6 |
|
Trimethylacetic acid, 99%
| 75-98-9 |
|
|