Search   
MSDS 
:
 4-Bromobenzaldehyde, 99%
CAS 
:
 1122-91-4
SYNONYMS 
:
 P-Bromobenzaldehyde
**** SECTION 2 - COMPOSITION, INFORMATION ON INGREDIENTS ****

+----------------+--------------------------------------+----------+-----------+
| CAS# | Chemical Name | % | EINECS# |
|----------------|--------------------------------------|----------|-----------|
| 1122-91-4 |4-Bromobenzaldehyde | 99 | 214-365-0 |
+----------------+--------------------------------------+----------+-----------+
Hazard Symbols: XI
Risk Phrases: 36/37/38

**** SECTION 3 - HAZARDS IDENTIFICATION ****

EMERGENCY OVERVIEW
Irritating to eyes, respiratory system and skin.Light sensitive.

Potential Health Effects
Eye:
Causes eye irritation.
Skin:
Causes skin irritation.
Ingestion:
Causes gastrointestinal irritation with nausea, vomiting and
diarrhea.
Inhalation:
Causes respiratory tract irritation.
Chronic:
No information found.

**** SECTION 4 - FIRST AID MEASURES ****

Eyes:
Flush eyes with plenty of water for at least 15 minutes,
occasionally lifting the upper and lower eyelids. Get medical aid.
Skin:
Get medical aid. Flush skin with plenty of water for at least 15
minutes while removing contaminated clothing and shoes. Wash clothing
before reuse.
Ingestion:
Never give anything by mouth to an unconscious person. Get medical
aid. Do NOT induce vomiting. If conscious and alert, rinse mouth and
drink 2-4 cupfuls of milk or water.
Inhalation:
Remove from exposure and move to fresh air immediately. If not
breathing, give artificial respiration. If breathing is difficult,
give oxygen. Get medical aid.
Notes to Physician:
Treat symptomatically and supportively.

**** SECTION 5 - FIRE FIGHTING MEASURES ****

General Information:
As in any fire, wear a self-contained breathing apparatus in
pressure-demand, MSHA/NIOSH (approved or equivalent), and full
protective gear. During a fire, irritating and highly toxic gases
may be generated by thermal decomposition or combustion. Vapors may
be heavier than air. They can spread along the ground and collect
in low or confined areas.
Extinguishing Media:
Use water spray, dry chemical, carbon dioxide, or appropriate foam.

**** SECTION 6 - ACCIDENTAL RELEASE MEASURES ****

General Information: Use proper personal protective equipment as indicated
in Section 8.
Spills/Leaks:
Clean up spills immediately, observing precautions in the Protective
Equipment section. Sweep up, then place into a suitable container for
disposal. Avoid generating dusty conditions. Provide ventilation.

**** SECTION 7 - HANDLING and STORAGE ****

Handling:
Wash thoroughly after handling. Remove contaminated clothing and
wash before reuse. Use only in a well-ventilated area. Avoid contact
with eyes, skin, and clothing. Keep container tightly closed. Avoid
ingestion and inhalation. Store protected from light. Wash clothing
before reuse.
Storage:
Keep container closed when not in use. Store in a cool, dry,
well-ventilated area away from incompatible substances. Keep
containers tightly closed. Store protected from light.

**** SECTION 8 - EXPOSURE CONTROLS, PERSONAL PROTECTION ****

Engineering Controls:
Facilities storing or utilizing this material should be equipped
with an eyewash facility and a safety shower. Use process enclosure,
local exhaust ventilation, or other engineering controls to control
airborne levels.
Exposure Limits
CAS# 1122-91-4:


Personal Protective Equipment

Eyes:
Wear appropriate protective eyeglasses or chemical
safety goggles as described by OSHA's eye and face
protection regulations in 29 CFR 1910.133 or European
Standard EN166.
Skin:
Wear appropriate gloves to prevent skin exposure.
Clothing:
Wear appropriate clothing to prevent skin exposure.
Respirators:
A respiratory protection program that meets OSHA's 29
CFR 1910.134 and ANSI Z88.2 requirements or European
Standard EN 149 must be followed whenever workplace
conditions warrant respirator use.

**** SECTION 9 - PHYSICAL AND CHEMICAL PROPERTIES ****

Physical State: Flakes
Color: white
Odor: None reported.
pH: Not available.
Vapor Pressure: Not available.
Viscosity: Not available.
Boiling Point: Not available.
Freezing/Melting Point: 55 - 58 deg C
Autoignition Temperature: Not available.
Flash Point: 108 deg C ( 226.40 deg F)
Explosion Limits, lower: N/A
Explosion Limits, upper: N/A
Decomposition Temperature:
Solubility in water: insoluble
Specific Gravity/Density:
Molecular Formula: C7H5BrO
Molecular Weight: 185.02

**** SECTION 10 - STABILITY AND REACTIVITY ****

Chemical Stability:
Stable at room temperature in closed containers under normal storage
and handling conditions.
Conditions to Avoid:
Incompatible materials, light, dust generation, excess heat, strong
oxidants.
Incompatibilities with Other Materials:
Strong oxidizing agents.
Hazardous Decomposition Products:
Carbon monoxide, irritating and toxic fumes and gases, carbon
dioxide, hydrogen bromide.
Hazardous Polymerization: Has not been reported.

**** SECTION 11 - TOXICOLOGICAL INFORMATION ****

RTECS#:
CAS# 1122-91-4: CU4810000
LD50/LC50:
CAS# 1122-91-4: Oral, mouse: LD50 = 1230 mg/kg.
Carcinogenicity:
4-Bromobenzaldehyde -
Not listed by ACGIH, IARC, or NTP.
Other:
See actual entry in RTECS for complete information.

**** SECTION 12 - ECOLOGICAL INFORMATION ****



**** SECTION 13 - DISPOSAL CONSIDERATIONS ****

Dispose of in a manner consistent with federal, state, and local regulations.

**** SECTION 14 - TRANSPORT INFORMATION ****

IATA
Not regulated as a hazardous material.
IMO
Not regulated as a hazardous material.
RID/ADR
Not regulated as a hazardous material.

**** SECTION 15 - REGULATORY INFORMATION ****

European/International Regulations
European Labeling in Accordance with EC Directives
Hazard Symbols: XI
Risk Phrases:
R 36/37/38 Irritating to eyes, respiratory system
and skin.
Safety Phrases:
S 26 In case of contact with eyes, rinse immediately
with plenty of water and seek medical advice.
S 37/39 Wear suitable gloves and eye/face
protection.
WGK (Water Danger/Protection)
CAS# 1122-91-4: No information available.
Canada
CAS# 1122-91-4 is listed on Canada's NDSL List.
CAS# 1122-91-4 is not listed on Canada's Ingredient Disclosure List.
US FEDERAL
TSCA
CAS# 1122-91-4 is listed on the TSCA inventory.

**** SECTION 16 - ADDITIONAL INFORMATION ****

MSDS Creation Date: 9/08/1998 Revision #2 Date: 3/18/2003

The information above is believed to be accurate and represents the best
information currently available to us. However, we make no warranty of
merchantability or any other warranty, express or implied, with respect to
such information, and we assume no liability resulting from its use. Users
should make their own investigations to determine the suitability of the
information for their particular purposes. In no way shall the company be
liable for any claims, losses, or damages of any third party or for lost
profits or any special, indirect, incidental, consequential or exemplary
damages, howsoever arising, even if the company has been advised of
the possibility of such damages.
--------------------------------------------------------------------------------
--------------------------------------------------------------------------------
Search More   
ALL MSDS PAGES IN THIS GROUP
NAMECAS
Ethyl chloroacetate 105-39-5
1,2:3,4-Di-O-isopropylidene-D-galactopyranose, 97% 4064-06-6
4-Nitrophenylhydrazine, 98% 100-16-3
1,1,4,4-Tetraphenyl-1,3-Butadiene, 99% 1450-63-1
2-Mercaptopyridine-n-oxide, sodium salt, monohydrate,98% 3811-73-2
1,3-Propane sultone, 97% 1120-71-4
Poly(ethylene glycol methyl ether), average M.W. 350 9004-74-4
Poly(ethylene glycol methyl ether), average mw. 750 9004-74-4
Azetidine, 99+% 503-29-7
Methyl Violet 2B High Purity Biological Stain 8004-87-3
Methyl Violet 2B (Cert) 8004-87-3
4,7-Diphenyl-1,10-Phenanthroline, 99% 1662-01-7
1',3',3'-Trimethyl-6-hydroxyspiro (2h-1-benzopyran-2,2'-indoline) 23001-29-8
Diethyl Carbonate, 99% 105-58-8
1,2,4-1h-triazole, 99+%, flakes 288-88-0
Hydroquinone Bis(2-Hydroxyethyl)ether, 99+% 104-38-1
Silicon, Pieces, 99.9999% 7440-21-3
Silicon, Powder, -60 Mesh, 99.999% 7440-21-3
Phenanthrenequinone, tech. 80% 84-11-7
3-Aminofluoranthene 2693-46-1
Phenanthrenequinone, 98% (uv-vis) 84-11-7
4-(4-Chlorophenyl)-4-hydroxypiperidine, 99%(titr.) 39512-49-7
4-Methyl-3-nitrobenzyl alcohol, 99% 40870-59-5
Amberlite ira-410 ion-exchange resin 9002-26-0
Isoprene, 99+%, stabilized with 100 ppm 4-tert-butylcatechol 78-79-5
Poly(isoprene), cis, average M.W. 800,000 9003-31-0
Isopropenyl Acetate, 99% 108-22-5
N,N,N',N'-Tetramethyl-p-phenylenediamine dihydrochloride, 96% 637-01-4
Ethyl-Vinyl Ether, 99%, stabilized with 0.1% Potassium Hydroxide 109-92-2
1,1,1-Trichloro-2-methyl-2-propanol hemihydrate 57-15-8
n-Butyric Anhydride, 98% 106-31-0
2,2',4'-Trichloroacetophenone,tech. 4252-78-2
Benz(a)anthracene-7,12-dione, 99% 2498-66-0
(+)-Limonene, 97%, stabilized with 0.03% Tocopherol 5989-27-5
(+)-Limonene, tech., 95%, stabilized with 0.03% Tocopherol 5989-27-5
2,4-Dichlorophenoxyacetic acid, 99+% 94-75-7
??-nicotinamide adenine dinucleotide, disodium salt,reduced form, 98% 606-68-8
4-Bromobenzaldehyde, 99% 1122-91-4
Benzyl cyanide, 99+% 140-29-4
5-Bromosalicylaldehyde, 99% 1761-61-1
Silica Gel, 60-200 Mesh 7631-86-9
Poly(acrylic acid), sec. stand., aver. M.W. 1,080,000, aver. M.N. 9003-01-4
Poly(acrylic acid), 50 wt. % solution in water 7732-18-5
(R)-(+)-1-Benzylglycerol, 97% 56552-80-8
Poly(acrylic acid), 25 wt% solution in water 7732-18-5
Poly(acrylic acid), 52-56% aqueous solution 7732-18-5
Potassium nitrosodisulfonate, 50-75%, remainder water and methanol 14293-70-0
Zinc, Powder, -200 Mesh, 99.9999% 7440-66-6
2-Dimethylaminoisopropyl chloride hydrochloride, 98.5% (titr.) 4584-49-0
Zinc, Mossy, 99+% 7440-66-6

Free MSDS Search ( Providing 250,000+ Material Properties )
Chemcas.com| Ads link:todaystock.net