**** SECTION 2 - COMPOSITION, INFORMATION ON INGREDIENTS ****
+----------------+--------------------------------------+----------+-----------+
| CAS# | Chemical Name | % | EINECS# |
|----------------|--------------------------------------|----------|-----------|
| 503-29-7 |Azetidine | 99.0 | 207-963-8 |
+----------------+--------------------------------------+----------+-----------+
Hazard Symbols: F+
Risk Phrases: 11 34
**** SECTION 3 - HAZARDS IDENTIFICATION ****
EMERGENCY OVERVIEW
Highly flammable. Causes burns.The toxicological properties of this
material have not been fully investigated.
Potential Health Effects
Eye:
No information regarding eye irritation and other potential effects
was found.
Skin:
No information regarding skin irritation and other potential effects
was found.
Ingestion:
The toxicological properties of this substance have not been fully
investigated.
Inhalation:
The toxicological properties of this substance have not been fully
investigated.
Chronic:
No information found.
**** SECTION 4 - FIRST AID MEASURES ****
Eyes:
Immediately flush eyes with plenty of water for at least 15 minutes,
occasionally lifting the upper and lower eyelids. Get medical aid
immediately.
Skin:
Get medical aid. Flush skin with plenty of soap and water for at
least 15 minutes while removing contaminated clothing and shoes.
Ingestion:
If victim is conscious and alert, give 2-4 cupfuls of milk or water.
Never give anything by mouth to an unconscious person. Get medical
aid immediately.
Inhalation:
Remove from exposure to fresh air immediately. If not breathing,
give artificial respiration. If breathing is difficult, give oxygen.
Get medical aid.
Notes to Physician:
**** SECTION 5 - FIRE FIGHTING MEASURES ****
General Information:
As in any fire, wear a self-contained breathing apparatus in
pressure-demand, MSHA/NIOSH (approved or equivalent), and full
protective gear. Vapors can travel to a source of ignition and flash
back. During a fire, irritating and highly toxic gases may be
generated by thermal decomposition or combustion. Use water spray to
keep fire-exposed containers cool. Extremely flammable liquid and
vapor. Vapors may be heavier than air. They can spread along the
ground and collect in low or confined areas. Will be easily ignited
by heat, sparks or flame. Vapors may form an explosive mixture with
air. Containers may explode when heated.
Extinguishing Media:
Use water spray to cool fire-exposed containers. For large fires,
use water spray, fog or alcohol-resistant foam. Do NOT use straight
streams of water. For small fires, use carbon dioxide, dry chemical,
dry sand, or alcohol-resistant foam. Cool containers with flooding
quantities of water until well after fire is out.
**** SECTION 6 - ACCIDENTAL RELEASE MEASURES ****
General Information: Use proper personal protective equipment as indicated
in Section 8.
Spills/Leaks:
Absorb spill with inert material (e.g. vermiculite, sand or earth),
then place in suitable container. Clean up spills immediately,
observing precautions in the Protective Equipment section. Remove all
sources of ignition. A vapor suppressing foam may be used to reduce
vapors. Water spray may reduce vapor but may not prevent ignition in
closed spaces.
**** SECTION 7 - HANDLING and STORAGE ****
Handling:
Wash thoroughly after handling. Remove contaminated clothing and
wash before reuse. Use with adequate ventilation. Ground and bond
containers when transferring material. Avoid contact with eyes, skin,
and clothing. Empty containers retain product residue, (liquid and/or
vapor), and can be dangerous. Keep container tightly closed. Avoid
contact with heat, sparks and flame. Avoid ingestion and inhalation.
Do not pressurize, cut, weld, braze, solder, drill, grind, or expose
empty containers to heat, sparks or open flames.
Storage:
Keep away from heat, sparks, and flame. Keep away from sources of
ignition. Store in a tightly closed container. Store in a cool, dry,
well-ventilated area away from incompatible substances.
**** SECTION 8 - EXPOSURE CONTROLS, PERSONAL PROTECTION ****
Engineering Controls:
Use adequate general or local exhaust ventilation to keep airborne
concentrations below the permissible exposure limits.
Personal Protective Equipment
Eyes:
Wear appropriate protective eyeglasses or chemical
safety goggles as described by OSHA's eye and face
protection regulations in 29 CFR 1910.133 or European
Standard EN166.
Skin:
Wear appropriate protective gloves to prevent skin
exposure.
Clothing:
Wear appropriate protective clothing to prevent skin
exposure.
Respirators:
Follow the OSHA respirator regulations found in 29CFR
1910.134 or European Standard EN 149. Always use a
NIOSH or European Standard EN 149 approved respirator
when necessary.
**** SECTION 9 - PHYSICAL AND CHEMICAL PROPERTIES ****
Physical State: Liquid
Appearance: clear slight brown
Odor: None reported.
pH: Not available.
Vapor Pressure: 176 hPa @ 19 C
Viscosity: Not available.
Boiling Point: 61 - 62 deg C @ 760.00mm Hg
Freezing/Melting Point: Not available.
Autoignition Temperature: Not available.
Flash Point: -20 deg C ( -4.00 deg F)
Explosion Limits, lower: Not available.
Explosion Limits, upper: Not available.
Decomposition Temperature:
Solubility in water: miscible
Specific Gravity/Density: .8470g/cm3
Molecular Formula: C3H7N
Molecular Weight: 57.09
**** SECTION 10 - STABILITY AND REACTIVITY ****
Chemical Stability:
Stable under normal temperatures and pressures.
Conditions to Avoid:
Incompatible materials, ignition sources, excess heat, strong
oxidants.
Incompatibilities with Other Materials:
Strong oxidizing agents.
Hazardous Decomposition Products:
Nitrogen oxides, carbon monoxide, irritating and toxic fumes and
gases, carbon dioxide, nitrogen.
Hazardous Polymerization: Has not been reported.
**** SECTION 11 - TOXICOLOGICAL INFORMATION ****
RTECS#:
CAS# 503-29-7 unlisted.
LD50/LC50:
Not available.
Carcinogenicity:
Azetidine -
Not listed by ACGIH, IARC, NIOSH, NTP, or OSHA.
See actual entry in RTECS for complete information.
**** SECTION 12 - ECOLOGICAL INFORMATION ****
**** SECTION 13 - DISPOSAL CONSIDERATIONS ****
Dispose of in a manner consistent with federal, state, and local regulations.
**** SECTION 14 - TRANSPORT INFORMATION ****
IATA
Shipping Name: FLAMMABLE LIQUID, CORROSIVE, N.O.S.*
Hazard Class: 3
UN Number: 2924
Packing Group: II
IMO
Shipping Name: FLAMMABLE LIQUID, CORROSIVE, N.O.S.
Hazard Class: 3.1
UN Number: 2924
Packing Group: II
RID/ADR
Shipping Name: FLAMMABLE LIQUID, CORROSIVE, N.O.S.
Dangerous Goods Code: 3(26B)
UN Number: 2924
**** SECTION 15 - REGULATORY INFORMATION ****
European/International Regulations
European Labeling in Accordance with EC Directives
Hazard Symbols: F+
Risk Phrases:
R 11 Highly flammable.
R 34 Causes burns.
Safety Phrases:
S 16 Keep away from sources of ignition - No
smoking.
S 24/25 Avoid contact with skin and eyes.
WGK (Water Danger/Protection)
CAS# 503-29-7: No information available.
United Kingdom Occupational Exposure Limits
Canada
CAS# 503-29-7 is listed on Canada's NDSL List.
CAS# 503-29-7 is not listed on Canada's Ingredient Disclosure List.
Exposure Limits
US FEDERAL
TSCA
CAS# 503-29-7 is listed on the TSCA inventory.
**** SECTION 16 - ADDITIONAL INFORMATION ****
MSDS Creation Date: 11/14/1997 Revision #1 Date: 8/02/2000
The information above is believed to be accurate and represents the best
information currently available to us. However, we make no warranty of
merchantability or any other warranty, express or implied, with respect to
such information, and we assume no liability resulting from its use. Users
should make their own investigations to determine the suitability of the
information for their particular purposes. In no way shall the company be
liable for any claims, losses, or damages of any third party or for lost
profits or any special, indirect, incidental, consequential or exemplary
damages, howsoever arising, even if the company has been advised of
the possibility of such damages.
--------------------------------------------------------------------------------
--------------------------------------------------------------------------------
|
|
|
| ALL MSDS PAGES IN THIS GROUP
| | NAME | CAS |
|
Ethyl chloroacetate
| 105-39-5 |
|
1,2:3,4-Di-O-isopropylidene-D-galactopyranose, 97%
| 4064-06-6 |
|
4-Nitrophenylhydrazine, 98%
| 100-16-3 |
|
1,1,4,4-Tetraphenyl-1,3-Butadiene, 99%
| 1450-63-1 |
|
2-Mercaptopyridine-n-oxide, sodium salt, monohydrate,98%
| 3811-73-2 |
|
1,3-Propane sultone, 97%
| 1120-71-4 |
|
Poly(ethylene glycol methyl ether), average M.W. 350
| 9004-74-4 |
|
Poly(ethylene glycol methyl ether), average mw. 750
| 9004-74-4 |
|
Azetidine, 99+%
| 503-29-7 |
|
Methyl Violet 2B High Purity Biological Stain
| 8004-87-3 |
|
Methyl Violet 2B (Cert)
| 8004-87-3 |
|
4,7-Diphenyl-1,10-Phenanthroline, 99%
| 1662-01-7 |
|
1',3',3'-Trimethyl-6-hydroxyspiro (2h-1-benzopyran-2,2'-indoline)
| 23001-29-8 |
|
Diethyl Carbonate, 99%
| 105-58-8 |
|
1,2,4-1h-triazole, 99+%, flakes
| 288-88-0 |
|
Hydroquinone Bis(2-Hydroxyethyl)ether, 99+%
| 104-38-1 |
|
Silicon, Pieces, 99.9999%
| 7440-21-3 |
|
Silicon, Powder, -60 Mesh, 99.999%
| 7440-21-3 |
|
Phenanthrenequinone, tech. 80%
| 84-11-7 |
|
3-Aminofluoranthene
| 2693-46-1 |
|
Phenanthrenequinone, 98% (uv-vis)
| 84-11-7 |
|
4-(4-Chlorophenyl)-4-hydroxypiperidine, 99%(titr.)
| 39512-49-7 |
|
4-Methyl-3-nitrobenzyl alcohol, 99%
| 40870-59-5 |
|
Amberlite ira-410 ion-exchange resin
| 9002-26-0 |
|
Isoprene, 99+%, stabilized with 100 ppm 4-tert-butylcatechol
| 78-79-5 |
|
Poly(isoprene), cis, average M.W. 800,000
| 9003-31-0 |
|
Isopropenyl Acetate, 99%
| 108-22-5 |
|
N,N,N',N'-Tetramethyl-p-phenylenediamine dihydrochloride, 96%
| 637-01-4 |
|
Ethyl-Vinyl Ether, 99%, stabilized with 0.1% Potassium Hydroxide
| 109-92-2 |
|
1,1,1-Trichloro-2-methyl-2-propanol hemihydrate
| 57-15-8 |
|
n-Butyric Anhydride, 98%
| 106-31-0 |
|
2,2',4'-Trichloroacetophenone,tech.
| 4252-78-2 |
|
Benz(a)anthracene-7,12-dione, 99%
| 2498-66-0 |
|
(+)-Limonene, 97%, stabilized with 0.03% Tocopherol
| 5989-27-5 |
|
(+)-Limonene, tech., 95%, stabilized with 0.03% Tocopherol
| 5989-27-5 |
|
2,4-Dichlorophenoxyacetic acid, 99+%
| 94-75-7 |
|
??-nicotinamide adenine dinucleotide, disodium salt,reduced form, 98%
| 606-68-8 |
|
4-Bromobenzaldehyde, 99%
| 1122-91-4 |
|
Benzyl cyanide, 99+%
| 140-29-4 |
|
5-Bromosalicylaldehyde, 99%
| 1761-61-1 |
|
Silica Gel, 60-200 Mesh
| 7631-86-9 |
|
Poly(acrylic acid), sec. stand., aver. M.W. 1,080,000, aver. M.N.
| 9003-01-4 |
|
Poly(acrylic acid), 50 wt. % solution in water
| 7732-18-5 |
|
(R)-(+)-1-Benzylglycerol, 97%
| 56552-80-8 |
|
Poly(acrylic acid), 25 wt% solution in water
| 7732-18-5 |
|
Poly(acrylic acid), 52-56% aqueous solution
| 7732-18-5 |
|
Potassium nitrosodisulfonate, 50-75%, remainder water and methanol
| 14293-70-0 |
|
Zinc, Powder, -200 Mesh, 99.9999%
| 7440-66-6 |
|
2-Dimethylaminoisopropyl chloride hydrochloride, 98.5% (titr.)
| 4584-49-0 |
|
Zinc, Mossy, 99+%
| 7440-66-6 |
|
|