Search   
MSDS 
:
 alpha,beta-Dichloroacrylonitrile, 98%
CAS 
:
 22410-58-8
SYNONYMS 
:
 2,3-Dichloro-2-propenenitrile; 2,3-Dichloroacrylonitrile.
**** SECTION 2 - COMPOSITION, INFORMATION ON INGREDIENTS ****

+----------------+--------------------------------------+----------+-----------+
| CAS# | Chemical Name | % | EINECS# |
|----------------|--------------------------------------|----------|-----------|
| 22410-58-8 |alpha,beta-Dichloroacrylonitrile | 98 | 244-964-2 |
+----------------+--------------------------------------+----------+-----------+
Hazard Symbols: XI
Risk Phrases: 36/37/38

**** SECTION 3 - HAZARDS IDENTIFICATION ****

EMERGENCY OVERVIEW
Irritating to eyes, respiratory system and skin.The toxicological
properties of this material have not been fully investigated.

Potential Health Effects
Eye:
Causes eye irritation.
Skin:
Causes skin irritation.
Ingestion:
May cause gastrointestinal irritation with nausea, vomiting and
diarrhea. The toxicological properties of this substance have not
been fully investigated. Metabolism may release cyanide, which may
result in headache, dizziness, weakness, collapse, unconsciousness
and possible death.
Inhalation:
Causes respiratory tract irritation. May be metabolized to cyanide
which in turns act by inhibiting cytochrome oxidase impairing
cellular respiration.
Chronic:
No information found.

**** SECTION 4 - FIRST AID MEASURES ****

Eyes:
Immediately flush eyes with plenty of water for at least 15 minutes,
occasionally lifting the upper and lower eyelids. Get medical aid.
Skin:
Get medical aid. Flush skin with plenty of water for at least 15
minutes while removing contaminated clothing and shoes. Wash clothing
before reuse.
Ingestion:
If victim is conscious and alert, give 2-4 cupfuls of milk or water.
Never give anything by mouth to an unconscious person. Get medical
aid.
Inhalation:
Remove from exposure and move to fresh air immediately. If not
breathing, give artificial respiration. If breathing is difficult,
give oxygen. Get medical aid.
Notes to Physician:

**** SECTION 5 - FIRE FIGHTING MEASURES ****

General Information:
As in any fire, wear a self-contained breathing apparatus in
pressure-demand, MSHA/NIOSH (approved or equivalent), and full
protective gear. During a fire, irritating and highly toxic gases
may be generated by thermal decomposition or combustion. Vapors may
be heavier than air. They can spread along the ground and collect
in low or confined areas.
Extinguishing Media:
Use water spray, dry chemical, carbon dioxide, or appropriate foam.

**** SECTION 6 - ACCIDENTAL RELEASE MEASURES ****

General Information: Use proper personal protective equipment as indicated
in Section 8.
Spills/Leaks:
Absorb spill with inert material (e.g. vermiculite, sand or earth),
then place in suitable container. Clean up spills immediately,
observing precautions in the Protective Equipment section. Remove all
sources of ignition. Provide ventilation.

**** SECTION 7 - HANDLING and STORAGE ****

Handling:
Wash thoroughly after handling. Ground and bond containers when
transferring material. Avoid contact with eyes, skin, and clothing.
Keep container tightly closed. Avoid ingestion and inhalation. Do
not pressurize, cut, weld, braze, solder, drill, grind, or expose
empty containers to heat, sparks or open flames. Use only with
adequate ventilation. Keep away from heat, sparks and flame. Pure
vapor will be uninhibited and may polymerize in vents or other
confined spaces.
Storage:
Keep away from sources of ignition. Store in a tightly closed
container. Store in a cool, dry, well-ventilated area away from
incompatible substances.

**** SECTION 8 - EXPOSURE CONTROLS, PERSONAL PROTECTION ****

Engineering Controls:
Facilities storing or utilizing this material should be equipped
with an eyewash facility and a safety shower. Use process enclosure,
local exhaust ventilation, or other engineering controls to control
airborne levels.
Exposure Limits
CAS# 22410-58-8:


Personal Protective Equipment

Eyes:
Wear chemical splash goggles.
Skin:
Wear appropriate protective gloves to prevent skin
exposure.
Clothing:
Wear appropriate protective clothing to prevent skin
exposure.
Respirators:
A respiratory protection program that meets OSHA's 29
CFR 1910.134 and ANSI Z88.2 requirements or European
Standard EN 149 must be followed whenever workplace
conditions warrant respirator use.

**** SECTION 9 - PHYSICAL AND CHEMICAL PROPERTIES ****

Physical State: Liquid
Color: clear, colorless to pale yellow
Odor: Irritating odor
pH: Not available.
Vapor Pressure: Not available.
Viscosity: Not available.
Boiling Point: 50-52 deg C @ 50 mm Hg
Freezing/Melting Point: Not available.
Autoignition Temperature: Not available.
Flash Point: 20 deg C ( 68.00 deg F)
Explosion Limits, lower: Not available.
Explosion Limits, upper: Not available.
Decomposition Temperature:
Solubility in water:
Specific Gravity/Density:
Molecular Formula: C3HCl2N
Molecular Weight: 121.96

**** SECTION 10 - STABILITY AND REACTIVITY ****

Chemical Stability:
Stable under normal temperatures and pressures.
Conditions to Avoid:
Light, ignition sources, excess heat, confined spaces.
Incompatibilities with Other Materials:
Strong oxidizing agents.
Hazardous Decomposition Products:
Hydrogen chloride, hydrogen cyanide, carbon monoxide, oxides of
nitrogen, carbon dioxide.
Hazardous Polymerization: May occur.

**** SECTION 11 - TOXICOLOGICAL INFORMATION ****

RTECS#:
CAS# 22410-58-8: AT5950000
LD50/LC50:
Not available.
Inhalation LCLo mouse: 910 mg/m3/10M.
Carcinogenicity:
alpha,beta-Dichloroacrylonitrile -
Not listed by ACGIH, IARC, or NTP.
Other:
See actual entry in RTECS for complete information.

**** SECTION 12 - ECOLOGICAL INFORMATION ****



**** SECTION 13 - DISPOSAL CONSIDERATIONS ****

Dispose of in a manner consistent with federal, state, and local regulations.

**** SECTION 14 - TRANSPORT INFORMATION ****

IATA
Not regulated as a hazardous material.
IMO
Not regulated as a hazardous material.
RID/ADR
Not regulated as a hazardous material.

**** SECTION 15 - REGULATORY INFORMATION ****

European/International Regulations
European Labeling in Accordance with EC Directives
Hazard Symbols: XI
Risk Phrases:
R 36/37/38 Irritating to eyes, respiratory system
and skin.
Safety Phrases:
S 26 In case of contact with eyes, rinse immediately
with plenty of water and seek medical advice.
S 37/39 Wear suitable gloves and eye/face
protection.
WGK (Water Danger/Protection)
CAS# 22410-58-8: No information available.
Canada
None of the chemicals in this product are listed on the DSL/NDSL list.
CAS# 22410-58-8 is not listed on Canada's Ingredient Disclosure List.
US FEDERAL
TSCA
CAS# 22410-58-8 is not listed on the TSCA inventory.
It is for research and development use only.

**** SECTION 16 - ADDITIONAL INFORMATION ****

MSDS Creation Date: 2/08/1999 Revision #3 Date: 10/21/2003

The information above is believed to be accurate and represents the best
information currently available to us. However, we make no warranty of
merchantability or any other warranty, express or implied, with respect to
such information, and we assume no liability resulting from its use. Users
should make their own investigations to determine the suitability of the
information for their particular purposes. In no way shall the company be
liable for any claims, losses, or damages of any third party or for lost
profits or any special, indirect, incidental, consequential or exemplary
damages, howsoever arising, even if the company has been advised of
the possibility of such damages.
--------------------------------------------------------------------------------
--------------------------------------------------------------------------------
Search More   
ALL MSDS PAGES IN THIS GROUP
NAMECAS
Sodium hydroxide, 50 wt% solution in water 1310-73-2
Sodium Deuteroxide, 40 wt. % Solution in D2O, 99+ Atom % D 7732-18-5
3,4,7,8-Tetramethyl-1,10-Phenanthroline, 99+% 1660-93-1
1,2,4-Trichlorobenzene, 99+% 120-82-1
1,2,4-Trichlorobenzene, 99% 120-82-1
Tetramethylene sulfoxide, 98+% 1600-44-8
Isoamyl nitrite, 90%, stabilized over molecular sieves 110-46-3
Benzyl chloroformate, 97%, stabilized with 0.1% anhydrous sodium 75-44-5
Dysprosium fluoride, 99.5% 13569-80-7
Erbium fluoride, 99% 13760-83-3
Praseodymium fluoride, anhydrous, 99.9% 13709-46-1
Styrene oxide, 98+% 96-09-3
Samarium fluoride, 99.9% 13765-24-7
Zirconium fluoride, 99.5% 7783-64-4
2,4,5-Trichlorothiophenol, Tech., 90% 3773-14-6
1,3-Benzenedisulfonyl Chloride, 98% (titr.) 585-47-7
Lutetium Fluoride, Anhydrous, 99.9% 13760-81-1
Zinc fluoride, hydrate 99% (ca 4 mole H2O) 7783-49-5
Indium fluoride, 99% 7783-52-0
Manganese(III) fluoride, 99% 7783-53-1
Aluminum fluoride, 99.9+% 7784-18-1
Chloromethyl-4-Chlorophenoxy Dimethylsilane, 98%
Chloromethyl-4-Chlorophenyl Dimethylsilane , 97% (GC) 770-89-8
alpha,beta-Dichloroacrylonitrile, 98% 22410-58-8
Cyanimidodithiocarbonic Acid Monomethyl Ester Monopotassium Salt, 98% 10191-61-4
5-Chloromethylthio-3-Methylmercapto-1,2,4- Thiadiazole, 95% (GC) 0-00-0
N-Chloromethylbenzothiazole-2-Thione, 98% 41526-42-5
N-Chloroacetyl Urethane, 98% 6092-47-3
Aluminum phosphate, 99% 7784-30-7
Gallium Sulfate, Anhydrous, 99.99% 13494-91-2
Aluminum sulfate, 99.99% 10043-01-3
Aluminum sulfate octadecahydrate, c.p. 7784-31-8
Aluminum sulfate octadecahydrate, reagent ACS 7784-31-8
Vanadium (IV) chloride 7632-51-1
Tetraethylammonium Chloride, 98% (Titr.) 56-34-8
Octane, 99+% 111-65-9
n-Octane, c.p. 111-65-9
Ether, stabilized, p.a. 60-29-7
Ether, stabilized, 99+% 60-29-7
Ether, spectro grade, stabilized, 99+% 60-29-7
Ethylene glycol, 99+%, anhydrous 107-21-1
Ethylene glycol, 95% (GC) 107-21-1
Ethylene glycol, p.a. 107-21-1
alpha-D-Lactose, monohydrate, reagent ACS 5989-81-1
alpha-Lactose monohydrate, 99.5+% (Lactose Monohydrate) 5989-81-1
Sodium antimonate, 96+% 15432-85-6
Hafnium Iodide, 99.8% 13777-23-6
Phosphoric acid (N-phenylsulfonylamide)dichloride 16767-55-8
N-Phenyliminophosphoric acid trichloride 5290-43-7
N-Phenyl-N'-Cyanoformamidine, 98% 59425-37-5

Free MSDS Search ( Providing 250,000+ Material Properties )
Chemcas.com| Ads link:todaystock.net