=====================  Product Identification  =====================

MSDS NAME:ULTRA-TEMP 516-T THINNER
NIIN:01-447-3026
Status Code:A
MSDS Number: CJMCK
=== Responsible Party ===
Company:AREMCO PRODUCTS INC
Address:707-B EXECUTIVE BLVD
Box:517
City:VALLEY COTTAGE
State:NY
ZIP:10989
Country:US
Info Phone Num:914-762-0685
Emergency Phone Num:914-268-0039
CAGE:34363
=== Contractor Identification ===
Company:AREMCO PRODUCTS INC
Address:707-B EXECUTIVE BLVD
Box:517
City:VALLEY COTTAGE
State:NY
ZIP:10989
Country:US
Phone:914-762-0685
Contract Num:SP0450-99-M-NH31
CAGE:34363

=============  Composition/Information on Ingredients  =============

Name:SILICATE SOLUTION
CAS:6834-92-0
RTECS #:VV9275000
= Wt:100.
Other REC Limits:NONE RECOMMENDED

=====================  Hazards Identification  =====================

Health Hazards Acute and Chronic:TARGET ORGANS: N/P. EFFECTS OF
    OVEREXPOSURE.  NHALATION: CAUSES IRRITATION TO THE RESPIRATORY
    TRACT; MAY CAUSE SNEEZING, BURNING, OR ITCHING IN NOSE AND THROAT.
    DERMAL EXPOSURE: CAUSES SKIN  IRRITATIO N; MAY CAUSE ITCHING AND
    BURNING OF SKIN. EYE:  IRRITATION: CAUSES EYE IRRITATION; MAY CAUSE
    PAIN, REDNESS, AND TEARING. INGESTION: CAUSES IRRITAITON TO THE
    ESOPHAGUS AND STOMACH. MAY CAUSE NAUSEA, VO MITING, AND DIARRHEA.
Effects of Overexposure:NHALATION CAUSES IRRITATION TO THE RESPIRATORY
    TRACT; MAY CAUSE SNEEZING, BURNING, OR ITCHING IN NOSE AND THROAT.
    DERMAL EXPOSURE CAUSES SKIN  IRRITATION; MAY CAUSE ITCHING AND
    BURNING OF SKIN. EYE  C ONTACT CAUSES EYE IRRITATION; MAY CAUSE
    PAIN, REDNESS, AND TEARING. INGESTION CAUSES IRRITAITON TO THE
    ESOPHAGUS AND STOMACH. MAY CAUSE NAUSEA, VOMITING, AND DIARRHEA.
Medical Cond Aggravated by Exposure:INHALATION MAY AGGRAVATE ASTHMA AND
    LUNG DISEASES.  SKIN CONTACT MAY AGGRAVATE ANY EXISTING SKIN
    DISEASES.

=======================  First Aid Measures  =======================

First Aid:INHALATION: REMOVE TO FRESH AIR, CONSULT A PHYSICIAN IF
    NECESSARY. EYES: FLUSH WITH LARGE AMOUNT OF WATER, LIFTING UPPER
    AND LOWER LIDS OCCASIONALLY. GET MEDICAL ATTENTION. SKIN: 
    THOROUGHLY WASH EXPO SED AREA WITH SOAP AND WATER. REMOVE
    CONTAMINATED CLOTHING, AND LAUNDER BEFORE RE-USE. INGESTION:
    IMMEDIATELY DRINK TWO GLASSES OF WATER AND	INDUCE VOMITING BY
    EITHER GIVING SYRUP OF IPECAC OR PLACIN G FINGER AT BACK OF THROAT.
     NEVER GIVE ANYTHING BY MOUTH TO AN UNCONSCIOUS PERSON. GET MEDICAL
    ATTENTION IMMEDIATELY.

=====================  Fire Fighting Measures  =====================

Flash Point:NO DATA
Autoignition Temp:Autoignition Temp Text:NO DAT
Lower Limits:NDA
Upper Limits:NDA
Extinguishing Media:NOT FLAMMABLE
Fire Fighting Procedures:USE SELF-CONTAINED AIR SUPPLIED BREATHING
    APPARATUS, AND IMPERVIOUS PROTECTIVE CLOTHING.
Unusual Fire/Explosion Hazard:NOT CONSIDERED A FIRE HAZARD AND DOEES
    NOT SUPPORT COMBUSTION. WHEN INVOLVED IN A FIRE, DOES NOT
    CONTRIBUTE ANY UNUSUAL HAZARDS.

==================  Accidental Release Measures  ==================

Spill Release Procedures:ISOLATE, DIKE AND STORE DISCHARGED MATERIAL,
    IF POSSIBLE. OTHEWISE DISPERSE AND FLUSH WITH WATER, OBSERVING
    ENVIRONMENTAL PROTECTION REGULATION.

=============  Exposure Controls/Personal Protection  =============

Respiratory Protection:USE NIOSH APPROVED MIST RESPIRATOR WHERE SPAY
    OCCURS.
Protective Gloves:RUBBER
Eye Protection:CHEMICAL GOGGLES
Supplemental Safety and Health
GOOD INDUSTRIAL HYGIENE PRACTICE REQUIRES THAT EMPLOYEE EXPOSURE BE
    MAINTAINED BELOW THE RECOMMENDED TLV. THIS IS PREFERABLY ACHIEVED
    THROUGH THE PROVISION OF ADEQUATE VENTILATION WHERE NECESSARY. WHE
    RE DUST CANNOT BE CONTROLLED IN THIS WAY, PERSONAL RESPIRATORY
    PROTECTION SHOULD BE EMPLOYED.

==================  Physical/Chemical Properties  ==================

HCC:N1
Boiling Pt:=98.9C, 210.F
Spec Gravity:1.4
Evaporation Rate & Reference:<1.00(BUTYL ACETATE=1)
Solubility in Water:COMPLETE
Appearance and Odor:COLORLESS TO HAZY LIQUID - ODORLESS

=================  Stability and Reactivity Data  =================

Stability Indicator/Materials to Avoid:YES
GELS WHEN MIXED WITH ACID.
Stability Condition to Avoid:FLAMMABLE HYDROGEN GAS MAY BE PRODUCED ON
    PROLONGED CONTACT WITH METALS SUCH AS ALUMINUM, TIN, LEAD, AND
    ZINC, IN AN ALKALINE ENVIRONMENT.
Hazardous Decomposition Products:FLAMMABLE HYDROGEN GAS MAY BE PRODUCED
    ON PROLONGED CONTACT WITH METALS SUCH AS ALUMINUM, TIN, LEAD, AND
    ZINC, IN AN ALKALINE ENVIRONMENT.
Conditions to Avoid Polymerization:WILL NOT OCCUR.

====================  Disposal Considerations  ====================

Waste Disposal Methods:DISPOSE OF IN ACCORDANCE WITH LOCAL, STATE, AND
    FEDERAL REGULATIONS.

 Disclaimer (provided with this information by the compiling agencies):
 This information is formulated for use by elements of the Department
 of Defense.  The United States of America in no manner whatsoever,
 expressly or implied, warrants this information to be accurate and
 disclaims all liability for its use.  Any person utilizing this
 document should seek competent professional advice to verify and
 assume responsibility for the suitability of this information to their
 particular situation.

*** END OF RECORD ***