=====================  Product Identification  =====================

MSDS NAME:LAGGING ADHESIVE &COATING 713 WHITE & RED
NIIN:01-101-3866
Status Code:A
MSDS Number: CLNWZ
=== Responsible Party ===
Company:VIMASCO CORP
Box:516
City:NITRO
State:WV
ZIP:25143
Country:US
Info Phone Num:304-755-3328
Emergency Phone Num:304-755-3328
Preparer's Name:ERNEST CARTER
Chemtrec Ind/Phone:(800)424-9300
CAGE:14947
=== Contractor Identification ===
Company:VIMASCO CORP
Box:516
City:NITRO
State:WV
ZIP:25143
Country:US
Phone:304-755-3328
CAGE:14947

=============  Composition/Information on Ingredients  =============

Name:ETHYLENE GLYCOL
CAS:107-21-1
RTECS #:KW2975000
= Wt:1.5
ACGIH STEL:C127 MG/M3;C50 PPM
EPA Rpt Qty:1 LB
DOT Rpt Qty:1 LB

Name:VINYL ACETATE-DIBUTYL MALEATE POLYMER
CAS:25035-90-9
= Wt:14.

Name:HEXYLENE GLYCOL
CAS:107-41-5
RTECS #:SA0810000
= Wt:.5
ACGIH STEL:C121 MG/M3;C25 PPM

Name:CHLORINATED PARAFFIN
CAS:63449-39-8
RTECS #:RV0450000
= Wt:6.

=====================  Hazards Identification  =====================

Health Hazards Acute and Chronic:ETHYLENE GLYCOL: CAN CAUSE SKIN AND
    EYE IRRITATION. EXCESSIVE INHALATION CAN CAUSE NASAL AND
    RESPIRATORY IRRITATION.INGESTION CAUSES DRUNKENNESS, RAPIDLY
    PASSING INTO COMA, WITH SERIOUS KIDNEY INJURY  AND/OR DEATH.
Medical Cond Aggravated by Exposure:PERSONS WITH PRE-EXISTING LUNG
    DISORDERS MAY BE MORE SUSCEPTIBLE.

=======================  First Aid Measures  =======================

First Aid:SKIN: WASH WITH SOAP AND WATER. EYES: FLUSH WITH CLEAN WATER
    AT LEAST 15 MINUTES, IF IRRITATION PERSISTS, CONSULT PHYSICIAN.
    INHALATION: REMOVE TO FRESH AIR.IF BREATHING IS DIFFICULT,
    ADMINISTER OXYGE N. IF IRRITATION PERSISTS, CONSULT
    PHYSICIAN.INGESTION: GIVE TWO GLASSES OF WATER, INDUCE VOMITING,
    CONSULT PHYSICIAN OR POISON CONTROL CENTER, NEVER GIVE ANYTHING BY
    MOUTH TO AN UNCONSCIOUS PERSON.

=====================  Fire Fighting Measures  =====================

Flash Point Method:TCC
Flash Point:=100.C, 212.F
Extinguishing Media:FOAM, ALCOHOL FOAM, CO2, DRY CHEMICAL, WATER FOG.
Fire Fighting Procedures:PRODUCT WILL NOT BURN UNTIL WATER HAS BOILED
    OR EVAPORATED.

==================  Accidental Release Measures  ==================

Spill Release Procedures:VENTILATE AREA. CONTAIN THE LIQUID WITH INERT
    MATERIALS SUCH AS SAND.ABSORB LIQUIDS USING AN INERT MATERIAL AND
    SHOVEL INTO CONTAINERS. PREVENT PRODUCT FROM ENTERING STREAMS OR
    DRINKING WATER SUPPLIES . BEFORE DRYING, PRODUCT MAY BE WASHED AWAY
    WITH WATER, AFTER DRYING REMOVE WITH A PAINT SCRAPER OR STRONG
    SOLVENT. SPILLED PRODUCT MAY BE SLIPPERY, WEAR NON-SKID FOOTWEAR.

======================	Handling and Storage  ======================

Handling and Storage Precautions:USE WITH ADEQUATE VENTILATION. STORE
    INDOORS AT TEMPERATURES OF 45 F TO 90 F .
Other Precautions:FOR INDUSTRY/PROFESSIONAL USE ONLY.

=============  Exposure Controls/Personal Protection  =============

Respiratory Protection:IN RESTRICTED VENTILATION AREAS,USE APPROVED
    CHEMICAL VAPOR RESPIRATOR. IN APPLICATIONS WHERE MISTS OR SPRAY MAY
    BE GENERATED, AVOID INHALATION OF AIRBORNE PARTICULATES BY USING AN
    APPROVED RESPIRATOR  WITH ORGANIC VAPOR CARTRIDGE WITH PREFILTER
    FOR MIST OR DUST.
Ventilation:GENERAL (MECHANICAL) ROOM VENTILATION IS EXSPECTED TO BE
    SATISFACTORY.
Protective Gloves:IMPERVIOUS GLOVES.
Eye Protection:GOGGLES, FACESHIELD, OR OTHER EYE WEAR TO PROTECT FROM
    SPLASH.
Work Hygienic Practices:THOROUGHLY CLEANSE HANDS AFTER HANDLING.
Supplemental Safety and Health

==================  Physical/Chemical Properties  ==================

Boiling Pt:=100.C, 212.F
Melt/Freeze Pt:=-3.7C, 25.F
Decomp Temp:=115.6C, 240.F
Vapor Density:LIGHTER
Spec Gravity:1.29
VOC Pounds/Gallon:575
pH:8.0 TO 9.0
VOC Grams/Liter:.48
Viscosity:75,000
Evaporation Rate & Reference:SLOWER THAN ETHER
Solubility in Water:APPRECIABLE
Appearance and Odor:VISCOUS, WHITE OR RED PASTE WITH MILD LATEX ODOR.
Percent Volatiles by Volume:60%

=================  Stability and Reactivity Data  =================

Stability Indicator/Materials to Avoid:YES
MATERIALS INCOMPATIBLE WITH WATER.
Hazardous Decomposition Products:WILL YIELD CO, CO2, HCI,
    ANTIMONY-OXYCHLORIDE, AND FRAGMENTED SHORT-CHAIN HYDROCARBONS.
Conditions to Avoid Polymerization:WILL NOT OCCUR.

====================  Disposal Considerations  ====================

Waste Disposal Methods:IN ACCORDANCE WITH ALL APPLICABLE REGULATIONS.

 Disclaimer (provided with this information by the compiling agencies):
 This information is formulated for use by elements of the Department
 of Defense.  The United States of America in no manner whatsoever,
 expressly or implied, warrants this information to be accurate and
 disclaims all liability for its use.  Any person utilizing this
 document should seek competent professional advice to verify and
 assume responsibility for the suitability of this information to their
 particular situation.

*** END OF RECORD ***