Material Safety Data Sheet
Section I - Product Identification
Manufacturer/Supplier:
Pittsburgh Corning Corporation
800 Presque Isle Drive Information Number: 724/327-6100
Pittsburgh, PA 15239 CHEMTREC: 800/424-9300
Product Name: PC庐 136 ADHESIVE Generic Name: Cementitious Grout Material
CAS Number: N. AP. CAS Name: N. AP.
NFPA HAZARD CLASS: Health: 1 Fire: 0 Reactivity: 0
WHMIS CLASSIFICATION: CLASS N/A Division N/A
Use: PC庐 136 ADHESIVE is a cementitious product that is mixed with water to form an inorganic,
noncombustible adhesive for fabricating FOAMGLAS庐 insulation.
Section II - Hazardous Ingredients
NTP***
IARC
ACGIH* OSHA** OSHA OSHA OSHA
Ingredient CAS Number TLV PEL STEL CEILING Reg.
Tetracalcium 3
Silicate 12168-85-3 30 mppcf .10mg/m N. AV. N. AV. N. AV
Dicalcium 3
Silicate 10034-77-2 30 mppcf .10mg/m N. AV N. AV. N.AV
Tricalcium 3
Aluminate 12042-78-3 30 mppcf .10mg/m N. AV N. AV. N.AV
Tetracalcium 3
Aluminoferrite 12068-35-3 30 mppcf .10mg/m N. AV N. AV. N. AV
Calcium 3
Sulphate 13397-24-5 30 mppcf .10mg/m N. AV. N. AV. N. AV
Comment: N. AV. - Not Available
N. AP. - Not Applicable
* American Conference of Governmental Industrial Hygienists.
** OSHA 29 CFR 1910.1000
*** Dangerous Properties of Industrial Materials, 7th Ed. by Sax/Lewis.
See Section VI - Toxicological and First Aid Information of this MSDS.
Product: PC庐 136 ADHESIVE Page 2 of 4
Section III - Physical Data
-Physical State at 77掳F (25掳C): Solid -Freezing Point: N. AP.
掳 掳
-Boiling Point: 1598掳F (870掳C) -Melting Point: N. AP
-Vapor Pressure -Specific Gravity 2.65
(mm of Mercury): N. AP.
-Vapor Density -Percent Volatile N. AP.
(Air = 1): N. AP.
-Solubility in Water: -Evaporation Rate
Slight N. AP.
-Appearance and Odor: Gray to dark gray dry
-Evaporation Rate
powder/slight odor N. AP.
-Odor Threshold: Negligible 8.9
-Coefficient of Water/Oil -pH:
Distribution: N. AV.
Section IV - Fire and Explosion Hazard Data
Conditions of Flammability: N. AP.
Flash Point: N. AP. Flammable Limits: LEL: N. AP. UEL: N. AP.
(Percent by Volume)
Auto Ignition Temperature: N. AP. Extinguishing Media: Not combustible, if decomposition
occurs use a self contained breathing
apparatus.
Special Fire Fighting Procedures: Wear self contained breathing apparatus and protective clothing.
FIRE AND EXPLOSION HAZARDS: None expected.
Hazardous Combustion Products: N/A
Explosion Data:
Sensitivity to mechanical impact: None. Sensitivity to static discharge: None.
Section I - Product Identification
Stability: Stable Conditions to Avoid: N/A
Incompatibility (Materials to Avoid): Organic and inorganic acids. Acid will react with cement and
carbonates.
Hazardous Decomposition or Byproducts: N/A
Hazardous Polymerization: Will not occur. Conditions to Avoid: N. AP.
Product: PC庐 136 ADHESIVE Page 3 of 4
Section VI - Toxicological and First Aid Information
OSHA Permissible Exposure Level: See Section II.
Routes of Entry: Inhalation: Yes Skin: Yes Ingestion: Yes Eye Contact: Yes
Effects of overexposure:
Acute: Inhalation - Product is alkaline and can irritate mucous membranes, coughing, shortness of
breath, liver effects.
Eyes - Product is alkaline and can irritate eye.
Skin - Product is alkaline and can irritate skin.
Ingestion - Seek medical attention.
IARC Cancer Review: Group 2A; Animal Sufficient Evidence; Human Limited Evidence
Medical conditions generally aggravated by exposure: None known.
Other Toxicological Properties: None known.
Emergency and First Aid procedures:
Eyes: Flush with potable water for 15 minutes, do not rub or apply pressure. Consult
physician or emergency medical service.
Skin: Wash with soap cold water.
Inhalation: Remove victim to fresh air. Treat symptomatically and consult physician
if irritation/symptoms persist.
Ingestion: Give milk or egg white beaten with water to induce vomiting. Consult
physician, emergency medical service or poison center.
Section VII - Precautions For Safe Handling and Use
Steps to be taken in case material is released or spilled: Use dustless methods. Do not dry sweep. Scoop
or vacuum discharge and place in dry drums.
Wear proper protection clothing and equipment.
All in accordance with local, state and federal
government regulations. Do not wash down
drains-may plug drain.
Waste Disposal Method: Dispose of in approved landfill in accordance with all local, state
and federal regulations.
Precautions to be taken in handling and storing: Store in a cool dry or moisture free area
and away from food and beverages. Keep
container closed when not in use. Wash
before eating, drinking, smoking or using
toilet.
Other Precautions: KEEP OUT OF REACH OF CHILDREN. For professional use only.
Not for sale to or use by the general public.
Product: PC庐 136 ADHESIVE Page 4 of 4
Section VIII - Personnel Protection Information
Eye Protection: Safety glasses with sideshields or goggles recommended.
Skin Protection: Normal work clothing covering arms and legs.
Respiratory Protection: A properly fitted, MSHA/NIOSH approved (3M9900 or equivalent) respirator
is recommended.
Ventilation: Provide adequate cross air circulation. Use mechanical/local exhuast at point of use or in
confined areas.
Other Protective Clothing or Equipment: Wear impervious rubber gloves.
Work/Hygienic Practices: Use good housekeeping and hygiene practices.
Section IX - Shipping Information
DOT Hazard Class: None.
Proper Shipping Name: Cementitious grouting material
UN # N. AV.
Section X - Preparation Information
Prepared by: H. J. Patrick
Date of Revision: 7/14/98
While the information and recommendations set forth herein are believed to be accurate, Pittsburgh Corning Corporation
makes no warranty with respect thereto, and disclaims all liability from reliance thereon.
PC庐 and FOAMGLAS庐 are registered trademarks of Pittsburgh Corning Corporation.
|