MATERIAL SAFETY DATA SHEET
ND INDUSTRIES , INC. PRODUCT: 310005 Instant Superglue
1893 BARRETT ROAD
MSDS ID: ND2185
TROY, MICHIGAN 48084
(248) 288-0000 Fax: (248) 288-0022
11/13/98 Updated: 11/1/00
DATE:
24 hr. EMERGENCY CHEMTREC:
PREPARED BY: Chemical Safety
1-800-424-9300
H: 2 F: 2 R: 2 PPE: H
SECTION I -Material Identification and Information
OSHA
PERCENT ACGIH OTHER LIMITS
CAS #
COMPONENTS PEL TLV RECOMMENDED
%
Ethyl cyanoacrylate 7085-85-0 95-100 n.e. n.e.
Hydroquinone 123-31-9 0-0.5 n.e. n.e.
All ingredients are listed on the TSCA Inventory. n.a.= not applicable / n.e.=not established
SECTION II -Physical and Chemical Characteristics
> 300掳F
BOILING POINT:
approx. 3.0 air = 1
VAPOR DENSITY:
<0.2 mmHg @ 75掳F
VAPOR PRESSURE:
n.a.
MELTING POINT:
1.06 water = 1
SPECIFIC GRAVITY:
n.a.
EVAPORATION RATE:
Yes, polymerization
WATER REACTIVE:
No, polymerized by water
SOLUBILITY IN WATER:
Clear viscous liquid with sharp irritating odor
APPEARANCE AND ODOR:
SECTION III - Fire and Explosion Hazard Data
FLASH POINT: 185掳F T.C.C.
AUTOIGNITION TEMPERATURE: not determined
UEL: n.a.
LEL: n.a.
FLAMMABILITY LIMITS % IN AIR:
EXTINGUISHER MEDIA: Carbon dioxide, dry chemical or foam
Wear a NIOSH approved self-contained breathing apparatus operated in pressure-demand or positive pressure
SPECIAL
when fighting fires.
FIREFIGHTING
PROCEDURES:
Possible exothermic reaction leading to substrate ignition and fume generation.
UNUSUAL FIRE
HAZARDS AND
CONDITIONS TO
AVOID:
MATERIAL SAFETY DATA SHEET
PRODUCT: 310005 Instant Superglue
SECTION IV - Reactivity Hazard Data
STABILITY: stable: X unstable:
HAZARDOUS POLYMERIZATION: may occur: X will not occur:
Amines and basic materials.
CONDITIONS TO
AVOID:
INCOMPATIBILITY: Polymerized by contact with water, alcohols, amines, and alkalies.
HAZARDOUS None
DECOMPOSITION
PRODUCTS:
SECTION V - Health Hazard Data
X X
PRIMARY ROUTES OF ENTRY: X
INHALATION: INGESTION: SKIN ABSORPTION:
Can cause irritation of the eyes. Can bond eyelids together.
EYE CONTACT:
Wash thoroughly with warm water and apply gauze patch. Get medical attention. The eye will open without further
action, typically in 1 to 4 days. DO NOT try to open the eyes by physical manipulation. Adhesion to eye
proteins will disassociate over several hours. This will cause periods of weeping. Seek medical attention.
FIRST AID:
Can cause irritation, bonding and drying of the skin.
SKIN CONTACT:
Immerse bonded surface in warm soapy water. Peel or roll surface apart with the aid of a blunt instrument.
Remove the adhesive from skin with warm, soapy water. DO NOT try to pull bonded surface apart as you may rip
FIRST AID:
or tear your skin. Seek medical attention
Vapor may be mildly irritating.
INHALATION:
This vapor is relatively harmless. Remove victim to fresh air. Seek medical attention
FIRST AID:
Relatively unlikely since material will solidify and adhere to the mouth.
INGESTION:
Saliva will lift the material in approximately one half to 2 days. In case a lump forms in the mouth, position the
FIRST AID:
patient to prevent ingestion of the lump when it detaches thus preventing choking. Seek medical attention.
Not determined
CHRONIC
EFFECTS:
Not listed.
Carcinogenic:
MATERIAL SAFETY DATA SHEET
PRODUCT: 310005 Instant Superglue
Component Oral LD50 Dermal LD50 Inhalation LC50
not determined
not determined
Ethyl cyanoacrylate not determined
not determined
not determined
Hydroquinone not determined
SECTION VI - Control and Protective Measures
RESPIRATORY Vapors are highly irritating to throat a respirator that protects against organic vapors should be worn at all times when
PROTECTION: handling, also work only in well ventilated areas.
PROTECTIVE Polyethylene gloves, DO NOT use cotton.
GLOVES:
EYE PROTECTION: Vapors are highly irritating to eyes vapor proof goggles should be worn.
LOCAL EXHAUST: MECHANICAL: SPECIFIC:
VENTILATION
TO BE USED: OTHER (specify): Positive down -draft exhaust ventilation should be provided to maintain vapor concentration below
TLV
Polyethylene apron.
PROTECTIVE CLOTHING
AND EQUIPMENT:
Always wash after using material.
HYGIENIC WORK
PRACTICES:
SECTION VII - Precautions for Safe Handling and Spill/Leak Procedures
STEPS TO BE TAKEN IF MATERIAL IS SPILLED OR RELEASED:
Flood with water to polymerize material. Soak up with absorbent material.
Collect polymerized material and dispose of according to local, state and federal regulations.
WASTE DISPOSAL
METHODS:
Store at or below 75掳F to maximize shelf life.
SAFE HANDLING AND
STORAGE:
OTHER PRECAUTIONS AND SPECIAL HAZARDOUS INFORMATION:
Avoid contact with skin and eyes. Avoid breathing vapors.
RECOMMENDED 2 2 2 H
HEALTH FLAMMABILITY REACTIVITY PERSONAL
NFPA/HMIS PROTECTION
note: ratings may differ according to application, environment, and physical state.
RATING
MATERIAL SAFETY DATA SHEET
PRODUCT: 310005 Instant Superglue
NOTES:
SECTION 313 SUPPLIER NOTIFICATION
Detaching this notification from the Material Safety Data Sheet is prohibited by law and any copying or distribution
of same requires this attachment be included.
This product contains the following toxic chemicals subject to the reporting requirements of section 313 of the
Emergency Planning and Community Right-To-Know Act of 1986 and 40 CFR 372:
CAS # CHEMICAL NAME % BY WEIGHT
123-31-9 Hydroquinone 0-0.5
This product contains the following materials that under California Proposition 65 of the Safe Drinking Water and Toxic
Enforcement Act of 1986 are recognized to cause cancer or reproductive toxicity.
cancer Reproductive cancer Reproductive
Concentration &
material CAS # agent Toxin agent Toxin
%
The information contained herein is based on the data available to us and is believed to be correct. However, ND Industries庐, Inc. makes no
warranty, expressed or implied regarding the accuracy of these data or the results to be obtained from the use thereof. Information is
supplied upon the condition that the persons receiving same will make their own determination as to its suitability for their properties prior to
use. Since conditions of use are beyond our control, all risks are assumed by the user.
|