FORM NO. 7978-J
NFPA Ratings
DATE REVISED: 06/16/2006
Fire
0 Reactivity
Health
Material Safety Data Sheet
2 0
(Essentially Similar to U.S. Department of Labor Suggested
Hazard Ratings
Form For Hazard Communication Compliance)
Special
4 = Extreme
3 = High
2 = Moderate
1 = Slight
I. Product Identification
0 = Insignificant
Product Type - MISCELLANEOUS NICKEL & COPPER COVERED ELECTRODES
Manufacturer - THE ESAB GROUP, INC. Telephone No. - 1-717-637-8911
Website: 1-800-933-7070
www.esabna.com
Address - 801 Wilson Avenue, P. O. Box 517 Emergency No. - 1-717-637-8911
Hanover, PA 17331 (CHEMTREC) 1-800-424-9300
APPROXIMATE COMPOSITION OF COVERED ELECTRODES (Wt. %)
ARCALOY ARCALOY ARCALOY ARCALOY ARCALOY ARCALOY ARCALOY BRONZE
Product Trade Name
A鉃? 112 鉃? 276 鉃? 8N12/8N12H 鉃? 9N10 鉃? Ni-9 鉃? CuNi 鉃? ARC C 鉃?
%Mn <3 <6 <6 4-6 2-4 2-4 1-2 --
%Cu -- <2 <2 -- 21-26 -- 45-56 72-78
%Al -- X X -- 1 -- <1 <1
%Ni 48-55 40-70 40-70 45-58 45-52 53-58 21-26 --
%Cr 10-12 <15 <15 9-12 -- 10-12 -- --
Mo <2 <10 <15 -- -- <8 -- --
W -- -- -- -- -- X -- --
Sn -- -- -- -- -- -- -- X
Si X X X -- X -- X --
Ti X X X X X -- X X
Cb* X X X X -- X -- --
MgCO3 -- -- -- -- -- -- -- X
CaCO3 X X X X X X X X
CaF2 X X X X X X X --
Cryolite X X X X X -- X X
Graphite -- X -- -- -- -- -- --
Mineral Silicates X -- -- X X X X X
TiO2 X X X X X X X --
Na Titanate X -- -- X -- -- -- --
K Titanate X X X X X X X --
Silicate Binder X X X X X X X X
Fe X X X X X X -- X
AWS Spec A5.11 A5.11 A5.11 A5.11 A5.11 A5.11 A5.6 A5.6
ENiCrFe-2 EniCrMo-3 ENiCrMo-4 ENiCrFe-3 EniCu-7 ENiCrMo-6 ECuNi ECuSn-C
Class
NOTE: X indicates material is present
* Also known as Niobium (Nb)
鉃? See Note in Section VI
鉃? See Note in Section VI
THE ESAB GROUP requests the users of these products to study this Material Safety Data Sheet (MSDS) and the product labels and
become fully aware of the product hazards and safety information. To promote the safe use of these products a user should (1) notify
and train its employees, agents and contractors concerning the information on this MSDS and any product hazards and safety
information, (2) furnish this same information to each of its customers for these products, and (3) request that such customers notify and
train their employees and customers, for these products, of the same product hazards and safety information.
-1-
Product Identity: MISCELLANEOUS NICKEL & COPPER COVERED ELECTRODES
FORM NO. 7978-J
DATE ISSUED: 06/16/2006
II. Hazardous Ingredients
IMPORTANT: This section covers the materials from which this product is manufactured. The fumes and gases produced during
normal use of these products are covered in Section V. The term HAZARDOUS should be interpreted as a term required and
defined by Laws, Statutes, or Regulations, and does not necessarily imply the existence of any hazard when the products are used as
directed by THE ESAB GROUP.
ACGIH TLV OSHA - PEL
3 3 3
Material (CAS No.) SARA TWA (mg/m ) TWA (mg/m ) STEL (mg/m )
Aluminum (7429-90-5) * 5 (Welding Fume) 5 (Welding Fume) --
Bentonite (1302-78-9) 10 (Nuisance Particulate) 10 (Nuisance Particulate) --
Calcium Carbonate (1317-65-3) 10 5 (Respirable Fraction) --
Chromium (Cr) (7440-47-3) * 0.5 (Metal) 1 (Metal) --
0.05 (CrVI inorganic compounds as 0.005 (CrVI inorganic compounds as
Cr , water soluble) CrVI, water soluble)
C 0.1 (as CrO3)
0.005 (CrVI inorganic compounds as
0.01 (CrVI inorganic compounds as
CrVI, water insoluble)
Cr, water insoluble)
C 0.1 (as CrO3)
Columbium (7440-03-1) 10 (Nuisance Particulate) 5 (Respirable Dust) --
Copper (7440-50-8) * 0.2 (Fume) 0.1 (Fume) --
Cryolite (15096-52-3) 2.5 (as F) 2.5 (as F) --
Fluorspar (7789-75-5) 2.5 (as F) 2.5 (as F) --
Graphite (7782-42-5) 2 2.5 (Respirable Dust) --
Iron (7439-89-6) 5 (Oxide Fume) 10 (Total Particulate) --
Magnesite (546-93-0) 10 5 (Respirable Fraction) --
Manganese (7439-96-5) * 0.2 (Fume) C 5 (STEL) 1 (Fume) 3
Mica (12001-26-2) 3 (Respirable Fraction) 3 (Respirable Dust) --
Molybdenum (7439-98-7) 5 (Soluble) 5 (Soluble) --
Nickel (7440-02-0) * 0.1 (Soluble) 0.1 (Soluble) --
Potassium Feldspar (68476-25-5) 10 (Nuisance Particulate) 5 (Respirable Fraction) --
Potassium Titanate (12030-97-6) 10 (Nuisance Particulate) 5 (Respirable Fraction) --
Silicate Binder (1344-09-8) 10 5 (Respirable) --
& (1312-76-1)
Silicon (7440-21-3) 10 (Dust) 5 (Respirable) --
Sodium Titanate (12034-34-3) 10 (Nuisance Particulate) 5 (Respirable Fraction) --
Tin (7440-31-5) 2 2 --
Titanium (7440-32-6) 10 (TiO2) 5 (TiO2 - Respirable) --
Titanium Dioxide (13463-67-7) 10 (Dust) 5 (Respirable) --
Tungsten (7440-33-7) 1 (Soluble Compounds, as W) 1 (Soluble Compounds, as W) 3
3 (STEL)
Wollastonite (13983-17-0) 10 (Calcium Silicate) 5 (Respirable Fraction) --
NOTE: In the ingredients table, an asterisk (*) after the CAS number indicates a toxic chemical subject to the reporting requirements
of Section 313 of the Emergency Planning and Community Right-To-Know Act of 1986 (SARA) and 40 CFR Part 372.
Some of these products may not contain all of the materials listed. For details of composition, refer to the COMPOSITION TABLE in
Section I.
In the table above, 鈥淐鈥? indicates 鈥淐eiling Limit.鈥?
III. Physical Data
As shipped, these products are nonflammable, non-explosive, non-reactive, and non-hazardous.
Physical State: GAS ( ) LIQUID ( ) SOLID (X)
Odor and Appearance: Nickel or Copper-based core wire with flux coating. Odorless.
-2-
Product Identity: MISCELLANEOUS NICKEL & COPPER COVERED ELECTRODES
FORM NO. 7978-J
DATE ISSUED: 06/16/2006
IV. Fire & Explosion Hazard
Flammable/Explosive: NO (X) YES ( )
Under what conditions: Only the packaging for this product will burn.
Extinguishing Media: This product will not burn; however, welding arcs and sparks can ignite combustible and flammable materials.
Use the extinguishing media recommended for the burning materials and fire situation. See ANSI Z49.1 鈥淪afety in Welding and
Cutting鈥? and 鈥淪afe Practices鈥? Code: SP, published by the American Welding Society, P. O. Box 351040, Miami, FL 33135, and
NFPA 51B 鈥淐utting and Welding Processes,鈥? published by the National Fire Protection Association, Batterymarch Park, Quincy, MA
02269 for additional fire prevention and protection information.
V. Reactivity Data
Stability: Stable (X) Unstable ( ) Polymerization will not occur.
Incompatible products: None currently known.
Hazardous decomposition products: Welding fumes and gases cannot be classified simply. The composition and quantity of both
are dependent upon the material being worked, the process, procedures, and consumables used. Other conditions which also
influence the composition and quantity of the fumes and gases to which workers may be exposed include: coatings on the material
being worked (such as paint, plating or galvanizing), the number of welding operations and the volume of the work area, the quality
and amount of ventilation, the position of the worker鈥檚 head with respect to the fume plume, as well as the presence of contaminants
in the atmosphere (such as chlorinated hydrocarbon vapors from cleaning or painting activities). When the materials are consumed,
the fume and gas decomposition products generated are different in percent and form from the ingredients listed in Section II.
Decomposition products of normal operation include those originating from the volatilization, reaction, or oxidation of the ingredients,
plus those from the material being worked and the coatings etc. noted above.
Reasonably expected decomposition products from normal use of these products include a complex of the oxides and fluorides of
the materials listed in Section II, as well as carbon monoxide, carbon dioxide, ozone and nitrogen oxides (refer to 鈥淐haracterization of
Arc Welding Fume鈥? available from the American Welding Society). THE FUME LIMIT FOR NICKEL, COPPER, CHROMIUM,
AND/OR MANGANESE MAY BE REACHED BEFORE THE GENERAL LIMIT FOR WELDING FUMES OF 5 mg/m3 IS REACHED.
MONITOR FUMES FOR NICKEL, COPPER, CHROMIUM, AND MANGANESE. A SIGNIFICANT AMOUNT OF THE CHROMIUM IN
THE FUMES CAN BE HEXAVALENT CHROMIUM, WHICH HAS A VERY LOW EXPOSURE LIMIT, 0.005 mg/m3 (5碌g/m3 ). The
only way to determine the true identity of the decomposition products is by sampling and analysis. The composition and quantity of
the fumes and gases to which a worker may be overexposed can be determined from a sample obtained from inside the welder鈥檚
helmet, if worn, or in the workers breathing zone. See ANSI/AWS F1.1 鈥淢ethod for Sampling Airborne Particles Generated by
Welding and Allied Processes,鈥? available from the American Welding Society.
VI. Physical and Health Hazard Data
Electric arc working may create one or more of the following health or physical hazards. Fumes and gases can be dangerous to your
health. Electric shock can kill you. Arc rays can injure eyes and burn skin. Noise can damage hearing. An additional detailed
description of the Health and Physical Hazards and their consequences may be found in ESAB鈥檚 free publications F52-529
鈥淧recautions and Safe Practices for Electric Welding and Cutting鈥? and F2035 鈥淧recautions and Safe Practices for Gas Welding,
Cutting and Heating.鈥? You may obtain copies from your local supplier or by writing to the address in Section I.
Route of overexposure: The primary route of entry of the decomposition products is by inhalation. Skin contact, eye contact, and
ingestion are possible. Absorption by skin contact is unlikely. When these products are used as recommended by THE ESAB
GROUP, and ventilation maintains exposure to the decomposition products below the limits recommended in this section,
overexposure is unlikely.
Effects of acute (short-term) overexposure to the gases, fumes, and dusts may include irritation of the eyes, lungs, nose, and
throat. Some toxic gases associated with welding may cause pulmonary edema, asphyxiation, and death. Acute overexposure may
include signs and symptoms such as watery eyes, nose and throat irritation, headache, dizziness, difficulty in breathing, frequent
coughing, or chest pain. The presence of chromium/chromate in fume can cause irritation of nasal membranes and skin. The
presence of nickel compounds in fume can cause metallic taste, nausea, tightness of chest, fever, and allergic reaction.
Pre-existing Medical Conditions Aggravated by Overexposure: Individuals with allergies or impaired respiratory function may
have symptoms worsened by exposure to welding fumes; however, such reaction cannot be predicted due to the variation in
composition and quantity of the decomposition products.
-3-
Product Identity: MISCELLANEOUS NICKEL & COPPER COVERED ELECTRODES
FORM NO. 7978-J
DATE ISSUED: 06/16/2006
Effects of chronic (long-term) overexposure to air contaminants may lead to their accumulation in the lungs, a condition which
may be seen as dense areas on chest X-rays. The severity of the change is proportional to the length of the exposure. The changes
seen are not necessarily associated with symptoms or signs of reduced lung function or disease. In addition, the changes on X-rays
may be caused by non-work factors such as smoking, etc. Nickel and chromium (in some products) are considered carcinogenic.
Long term overexposure to nickel fumes may also cause pulmonary fibrosis and edema. Overexposure to manganese compounds
may affect the central nervous system, symptoms of which are languor, sleepiness, muscular weakness, emotional disturbances, and
spastic gait.
Exposure limits for the ingredients are listed in Section II. The 1989 OSHA TWA for welding fume is 5 mg/m鲁. TLV-TWAs should
be used as a guide in the control of health hazards and not as fine lines between safe and excessive concentrations. When these
products are used as recommended by THE ESAB GROUP, and the preventive measures taught in this MSDS are followed,
overexposure to hazardous substances will not occur.
Emergency First Aid Measures: In case of emergency, call for medical aid. Employ first aid technique recommended by the Red
Cross. IF BREATHING IS DIFFICULT, give oxygen and call for a physician. FOR ELECTRIC SHOCK, disconnect and turn off the
power. If not breathing, begin artificial respiration, preferably mouth-to-mouth. If no detectable pulse, begin Cardio Pulmonary
Resuscitation (CPR). Immediately call a physician. FOR ARC BURN, apply cold, clean compresses and call a physician.
Carcinogenic Assessment (NTP Annual Report, IARC Monographs, Other): Nickel and Chromium must be considered possible
carcinogens under OSHA (29CFR1910.1200). IARC has indicated Nickel, Chromium and certain of their compounds are probably
carcinogenic for humans, but the compounds cannot be specified precisely. Their conclusions were drawn from operations different
from welding. Regardless, exposure level must be kept below those levels specified in Section II.
鉃? WARNING: This product, when used for welding or cutting, produces fumes or gases which contain chemicals known to the
State of California to cause birth defects and, in some cases, cancer. (California Health & Safety Code 搂25249.5 et
seq.)
鉃? WARNING: This product contains or produces a chemical known to the State of California to cause cancer and birth defects (or
other reproductive harm). (California Health & Safety Code 搂25249.5 et seq.)
VII. Precautions for Safe Handling and
Use/Applicable Control Measures
Read and understand the manufacturer鈥檚 instructions and the precautionary label on this product. See American National Standard
Z-49.1, 鈥淪afety in Welding and Cutting,鈥? published by the American Welding Society, P. O. Box 351040, Miami, FL 33135 and OSHA
Publication 2206 (29 C.F.R. 1910), U.S. Government Printing Office, Superintendent of Documents, P.O. Box 371954, Pittsburgh, PA
15250-7954 for more detail on many of the following:
Ventilation: Use enough ventilation, local exhaust at the arc, or both, to keep the fumes and gases below the TLVs in the
worker鈥檚 breathing zone and the general area. Train the welder to keep his head out of the fumes.
Respiratory Protection: Use respirable fume respirator or air supplied respirator when welding in confined space or where
local exhaust or ventilation does not keep exposure below TLV.
Eye Protection: Wear helmet or use face shield with filter lens. As a rule of thumb, start with a shade which is too dark to see
the weld zone. Then go to the next lighter shade which gives sufficient view of the weld zone. Provide protective screens and
flash goggles, if necessary, to shield others.
Protective Clothing: Wear head, hand, and body protection which help to prevent injury from radiation, sparks and electrical
shock. See ANSI Z-49.1. At a minimum, this includes welder鈥檚 gloves and a protective face shield and may include arm
protectors, aprons, hats, shoulder protection, as well as dark substantial clothing. Train the welder not to touch live electrical
parts and to insulate himself from work and ground.
Procedure for Cleanup of Spills or Leaks: NOT APPLICABLE
Waste Disposal Method: Prevent waste from contaminating surrounding environment. Discard any product, residue,
disposable container, or liner in an environmentally acceptable manner, in full compliance with Federal, State and Local
regulations.
The opinions expressed in this MSDS are those of qualified experts within THE ESAB GROUP. We believe that the information
contained herein is current as of the date of this MSDS. Since the use of this information and these opinions and the conditions of
use of these products are not within the control of THE ESAB GROUP, it is the user鈥檚 obligation to determine the conditions of safe
use of these products.
-4-
|