MSDS
Product: SR 1200
Rev # 4 Dated 11/9/2004
Page 1 of 4
MATERIAL SAFETY DATA SHEET
1. CHEMICAL PRODUCT AND COMPANY INFORMATION
Product Name: SR 1200
Chemical: Mixture Chemical Family: Organic Mixture
2. COMPOSITION / INFORMATION ON INGREDIENTS
Component Name CAS# %Range
Heavy aromatic distillate 064742-91-2 <30-60%
Imidazoline Derivative 061791-39-7 <20-50%
1,2,4 trimethylbenzene 000091-63-6 <3%
xylene 001330-20-7 <3%
naphthalene 000091-20-3 <2%
ethyl toluene 025550-14-5 <2%
cumene 000098-82-8 <2%
1-ethyl-2-methyl-benzene 000611-14-3 <1%
1-methyl-4-ethylbenzene 000622-96-8 <1%
3. HAZARDS IDENTIFICATION
Form: Liquid
Color: Clear yellow to amber liquid
Potential Health Effects:
Primary Routes of Exposure:
Skin Contact: Frequent or prolonged contact may irritate and casue dermatitis.
Low order of toxicity.
Skin contact may aggravate an existing dermatitis condition.
Eye Contact: Slightly irritating but does not injure eye tissue.
Ingestion: Small amounts of this product aspirated into the respiratory system during ingestion or vomiting may cause mild to
severe pulmonary injury, possibly progressing to death.
Minimal toxicity
Inhalation: High vapour/aerosol concentrations (greater than approximately 1000 ppm) are irritating to the eyes and the
respiratory tract, may cause headaches, dizziness, anesthesia, drowsiness, unconsciousness, and other central nervous system
effects including deaths.
CHRONIC EFFECTS: At high oral doses in rats this product caused damage to the stomach, liver, thyroid and urinary bladder.
These effects are not relevant to humans at occupational levels of exposure.
This product contains naphthalene. A National Toxicology Program (NTP) report states that lifetime inhalation exposure to
naphthalene resulted in increases in tumors of the nose in rats. In a previous NTP study, lifetime in halation exposure to
naphthalene increased lung tumors in female mice. The relevance o f the rodent findings to humans is questionable.
Carcinogenicity Classification:
International Agency for Research on Cancer (IARC): N/A
U.S. National Toxicology Program (NTP): N/A
U.S. Occupational Safety and Health Administration (OSHA): N/A
American Conference of Governmental Industrial Hygienists (ACGIH): N/A
4. FIRST AID MEASURES
Eye Contact: Rinse with immediately with plenty of water for at least 15 minutes. In case of eye irritation, seek medical attention.
Skin Contact: Wipe with absorbent paper or textile towels. Wash off with soap and plenty of water. Do not use organic solvents. In
case of dermatitis, seek medical attention.
After inhalation: Move to fresh air. In case of irritation of respiratory system or mucous membranes, seek medical attention. In
case of indisposition, seek medical attention. In case of prolonged exposure, seek medical attention.
After ingestion: Immediately give plenty (> 500 ml) of water (if possible charcoal slurry). In case of spontaneous vomiting be sure
that vomitus can freely drain due to danger of suffocation. Give water repeatedly. Artificial induction of vomiting should be restricted
to first aid staff. Give nothing by mouth in cases of unconsciousness or convulsion. Seek medical advice.
MSDS
Product: SR 1200
Rev # 4 Dated 11/9/2004
Page 2 of 4
5. FIRE FIGHTING MEASURES
Suitable extinguishing media: Water spray, foam, Carbon dioxide (CO2), Dry Powder.
Fire and explosion hazards: Contaminated water from fire hoses or sprinklers, etc. must be prevented from draining into
watercourses, sewers or the ground water. Sufficient measures must be taken to retain water used for extinguishing. Contaminated
water and soil must be disposed of in conformity with local regulation.
Special protective equipment: Wear full protective clothing. Wear self-contained breathing apparatus.
Flash point: > 62 掳C
6. ACCIDENTAL RELEASE MEASURES
Personal protection: Avoid contact with skin, eyes and clothing.
Environmental precautions: Do not flush into surface water, sanitary sewer or ground water system.
Clean-up: Soak up with inert absorbent material (e.g. sand, silica gel, acid binder, universal binder sawdust). Collect the spilled
product into suitable containers, which must be tightly sealed and properly labeled.
Water Spill: Eliminate sources of ignition. Warn occupants and shipping in surrounding and downwind areas of fire and explosion
hazard and request all to stay clear. Consult an expert on disposal of recovered material and ensure conformity to local disposal
regulations.
7. HANDLING AND STORAGE
Electrostatic Accumulation Hazard: Yes, use proper bonding and /or grounding procedure.
Additional information regarding safe handling of products with static accumulation potential can be ordered by contacting the
American Petroleum Institute (API) for API Recommended Practice 2003 entitled 鈥淧rotection Against Ignitions Arising Out of Static.
Lightning and Stray Currents鈥? (American Petroleum Institute 1220 L Street Northwest, Washington, DC 20005) or the National Fire
Protection Association (NFPA) for NFPA 77 entitled 鈥? Static Electricity鈥? (National Fire Protection Association). 1 Batterymarch Park.
P.O. Box 9101, Qunicy MA 02269-9101).
Storage and Handling: Keep container closed. Handle and open containers with care. Store in a cool, well ventilated place away
from incompatible materials. DO NOT handle or store near an open flame, heat or other sources of ignition. Protect material from
direct sunlight. Material will accumulate static charges which may cause an electrical spark (ignition source). Use proper bonding
and/or grounding procedures. DO NOT pressurize, cut, heat, or weld containers. Empty product containers may contain product
residue. Do Not reuse empty containers without commercial cleaning or reconditioning.
8. EXPOSURE CONTROLS / PERSONAL PROTECTION
Exposure controls: The use of local exhaust ventilation is recommended to control process emissions near the source.
Laboratory samples should be handled in a lad hood. Provide mechanical ventilation of confined spaces. See respiratory protection
recommendations.
Personal protection equipment: For open systems where contact is likely, wear safety glasses with side shields, long sleeves,
and chemical resistant gloves. Where contact may occur, wear safety glasses with side shields. Where concentrations in air may
exceed the limits given in this Section and engineer, work practice or other means of exposure reduction are not adequate, NIOSH
approved respirators may be necessary to prevent overexposure by inhalation.
Eye protection: Suitable goggles or face protection.
Hand protection: Protective gloves.
Skin and body protection: Working clothes, closed footwear.
Respiratory protection: In case of insufficient ventilation wear suitable respiratory equipment.
Workplace Exposure Guidelines OSHA Regulation 29CFR1910.1000 requires the following permissible exposure limits: A
3 3
TWA of 10 ppm (50 mg/m ) and a STEL o f15 ppm (75 mg/m ) for Naphthalene. The recommended permissible exposure levels
indicated above reflect the levels revised by OSHA in 1989 or in subsequent regulatory activity. Although the 1989 levels have
th
since been vacated by the 11 Circuit Court of Appeals, we recommend that the lower exposure levels be observed as reasonable
worker protection.
3
The ACGIH Recommends the Following Threshold Limit Values: A TWA of 10 ppm (52 mg/m ) and a STEL of 15 ppm (79
3
mg/m ) for Naphthalene, with skin and A4 designations.
MSDS
Product: SR 1200
Rev # 4 Dated 11/9/2004
Page 3 of 4
9. PHYSICAL AND CHEMICAL PROPERTIES
These data do not represent technical or sales specification
Form: Liquid Colour: Clear yellow to amber Liquid
Odour: Aromatic Boiling point/range: NA
Melting point/range: NA
Flash point: > 62掳C Autoignition temperature: NA
Explosion limits: NA Vapour pressure: NA
Relative density/Sp Gr: 0.90-0.96 @ 15.6掳C Vapour density: NA
Kinematic Viscosity: 2 - 16 cSt @ 40掳C Water solubility: ND
Solubility: ND
Abbreviations: N.D. 鈥? Not Determined
N.A. - Not Applicable
10. STABILITY
Stability: Stable
Hazardous decomposition products: Oxides of carbon, oxides of nitrogen (NOx), Toxic gases/ vapors.
Conditions/Materials to avoid: Strong acids, strong bases and strong oxidizing agents. Static discharges.
11. TOXICOLOGICAL INFORMATION
Please refer to Section 3 for available information on potential health effects.
12. ECOLOGICAL INFORMATION
Mobility: ND Biodegradation: ND
Bioaccumulation: ND Aquatic toxicity: ND
Acute toxicity to fish (Fish general (Pisces)): ND
Acute toxicity to daphnia (Daphnia magna): ND
Acute toxicity to algae (Algae): ND
Further information: Do not discharge product uncontrolled into the environment.
This material is expected to be toxic to aquatic organisms.
13. DISPOSAL CONSIDERATIONS
Provisions relating to waste: Residual chemical should be disposed by incineration or by other modes of disposal in companies
with local legislation.
Disposal information: Contaminated packaging material should be treated equivalent to residual chemical. Clean packing
material should be subjected to waste management schemes (recovery recycling, reuse) according to local legislation.
14. TRANSPORT INFORMATION
Proper shipping name: Not Regulated
Note: In containers of 450 litre/420 kgs/119 gallons capacity or less in a quantity per container of less than 325 liter/303 kgs/119
gallons. This product is not regulated by DOT.
15. REGULATORY INFORMATION
United States
Toxic Substances Control Act (TSCA): All components of this product are in compliance with the inventory listing requirements
of the U. S. Toxic Substances Control Act (TSCA) Chemical Substance Inventory.
MSDS
Product: SR 1200
Rev # 4 Dated 11/9/2004
Page 4 of 4
16. OTHER INFORMATION
For additional information concerning this product, contact the following:
PRODUCT EMERGENCIES
Dorf Ketal Chemicals (I) Pvt. Ltd. Dorf Ketal LLC
#1 DORF KETAL TOWERS. 3727 Green briar
D鈥橫onte Street, Marve Road. Suite 114
Malad (W).Bombay 64. Stafford. TX 77477
Tel: +91-22-28813654 / +91-22-28828374. Tel no.: 281-491-3700
Fax: +91-22-28882366
The data and recommendations presented in this data sheet concerning the use of our product and the materials contain there in are believed to be
accurate and are based on information which is considered reliable as of the date hereof. However, the customer should determine the suitability of
such material for his purpose before adopting them on a commercial scale. Since the use our products by others is beyond our control, no
guarantee, express or implied, is made and no responsibility assumed for the use of this material or the results to be obtained there from.
Information on this form is furnished for the purpose of compliance with Government Health and Safety Regulations and shall not be used for any
other purposes. Moreover, the recommendations contained in this data sheet are not to be constructed as a license to operate under, or a
recommendation to infringe, any existing patents, nor should they be confused with state, municipal or insurance requirements, or with national
safety codes.
END OF MSDS
|