Search    ENTER KEYWORD
MSDS Material Safety Data Sheet
CAS

34590-94-8

File Name: inlandcoatings_com---msd2030.asp
                                                                   HEALTH       1
FLAMMABILITY 0
REACTIVITY 0


MATERIAL SAFETY DATA SHEET
RS-2030 ROOFING SEALER
MSDS NO.: LM2030 PAGE 1 OF 5
Reviewed: 4/02/07
SECTION 1: PRODUCT AND COMPANY IDENTIFICATION.


INLAND COATINGS CORP. Hours of Operation: 8:00am-5:00pm
2619 HWY 6 Phone Number: 515-993-4524
PO BOX 247 Fax Number: 515-993-4324
ADEL IA 50003-0247 Chemtrec Number: 800-424-9300


SECTION 2: COMPOSITION AND INFORMATION ON INGREDIENTS.

Hazardous Ingredients: CAS # PERCENT

Dipropylene Glycol Monomethyl Ether 34590-94-8 2.6%

SECTION 3: HAZARDS IDENTIFICATION.

EMERGENCY OVERVIEW: Milky white liquid with mild odor. May be
irritating to eyes.
POTENTIAL HEALTH HAZARDS:
EYES: Direct contact may be irritating to the eyes.

SKIN: Prolonged or repeated exposure may be
irritating. Skin absorption is unlikely. Not
considered to be a sensitizer.

INHALATION: Signs and symptoms of excessive exposure
may be anesthetic or narcotic effects.

INGESTION: Gastric disturbance. Small amounts
swallowed incidental to normal handling
operations are not likely to cause injury.
Swallowing amounts larger than that may
cause injury.
RS-2030 SEALER
MSDS NO: LM2030 PAGE 2 OF 5

SECTION 4: FIRST AID PROCEDURES.

EYES: If irritation or redness from exposure to vapors
develops, remove victim away from exposure and
into fresh air. If irritation or redness persists, seek
medial attention. For direct contact, flush eye(s)
with clean water for 15 minutes and get medical
attention.
SKIN: Remove contaminated clothing. Wash affected
area(s) with mild soap and water. Apply skin
cream. Seek medical attention if irritation
developes.
INHALATION: Remove to fresh air. If any irritation develops seek
medical attention.
INGESTION: Induce vomiting if large amounts are ingested.
Seek medical attention.

SECTION 5: FIRE FIGHTIN
SECTION 5: FIRE FIGHTING PROCEDURES.

FLAMMABLE CLASSIFICATIONS: Not combustible

FLASH POINT: None LIMITS OF FLAMMABILITY
LEL: N/A
UEL: N/A

EXTINGUISHING MEDIA: This is a water based product and will not
support combustion. On dried product, use
water, foam, CO2, or dry chemical
extinguisher.

FIRE AND EXPLOSION HAZARDS: None Known

FIRE FIGHTING EQUIPMENT: Wear NIOSH approved equipment including
a positive pressure self contained breathing
apparatus in any closed spaces.

SECTION 6: ACCIDENTAL RELEASE PROCEDURES.

If material is spilled, stop the discharge and dam up to limit spreading. Avoid breathing
of vapors. Take up with absorbent material and place in suitable container for further
handling and disposal. Keep out of drains, sewers or waterways.
RS-2030 SEALER
MSDS NO: LM2030 PAGE 3 OF 5

SECTION 7: HANDLING AND STORAGE.

HANDLING: INDUSTRIAL USE ONLY
Avoid breathing of vapors. Do not get into eyes. Avoid
prolonged or repeated skin contact. Follow good personal
and industrial hygiene procedures.

STORAGE: Store in a cool, dry, well ventilated area. Avoid freezing.


SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION.

RESPIRATORY PROTECTION: Use in well ventilated areas only. NIOSH/MSHA
approved respirators may be necessary to prevent over
exposure by inhalation.

VENTILATION: Local exhaust may be necessary for some operations.

SKIN PROTECTION: Protective clothing with long sleeves should be worn.
Launder or dry clean when soiled. Gloves resistant to
petroleum should be worn.

EYE PROTECTION: Wear safety goggles where contact or splash potential
exists.

SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES.
ODOR: Mild SPECIFIC GRAVITY: 1.02
BOILING RANGE/POINT: 100掳 C (212掳 F) POUNDS/GALLON: 8.47
VAPOR PRESSURE: Same as water VAPOR DENSITY: (air=1):<1
EVAPORATION RATE: Slower than ether SOLUBILITY IN WATER: Miscible
SOLID/WEIGHT 44.1%


SECTION 10: STABILITY AND REACTIVITY.

STABILITY: Stable

INCOMPATIBILITY: Isolate from strong oxidizers.
RS-2030 SEALER
MSDS: LM2030 PAGE 4 OF 5

SECTION 10: STABILITY AND REACTIVITY (continued..)

HAZARDOUS DECOMPOSITION PRODUCTS: Thermal decomposition may release toxic
and/or hazardous gases.

HAZARDOUS POLYMERIZATION: Will not occur.

SECTION 11: TOXICOLOGICAL INFORMATION.

ACUTE: This formulation has not been tested for acute toxicity. It is expected to
have a low order of acute oral toxicity. However, due to the presence of
a surfactant, it may be irritating to the skin and eyes.

CHRONIC: This material has not been identified as a carcinogen by IARC, NTP, or
OHSA. Chronic health effects would not be expected as long as good
industrial hygiene and proper safety precautions are provided.

TARGET ORGANS: Eyes.

SECTION 12: ECOLOGICAL INFORMATION.

This formulation has not been tested for environmental effects.

SECTION 13: DISPOSAL CONSIDERATIONS.


Dispose in accordance with local, state and federal regulations.

Container disposal: Residual product may be present in used containers.
Do not reuse container for food, clothing, or products for human or
animal consumption.

SECTION 14: TRANSPORTATION INFORMATION.


DOT SHIPPING NAME: Paint

HAZARD CATEGORY: Not regulated.

UN/NA#: UN1263
RS-2030 SEALER
MSDS NO: LM2030 PAGE 5 OF 5

SECTION 15: REGULATORY INFORMATION.

SARA HAZARD CATEGORY: Fire Hazard: No
Sudden Release of Pressure: No
Reactivity Hazard: No
Acute Health Hazard: Yes
Chronic Health Hazard: No

SARA 313 INFORMATION: SUPERFUND AMMENDMENTS AND
REAUTHORIZATION ACT OF 1986 (SARA) Title III
requires reports of toxic chemicals that appear in 40 CFR
372. This information must be included in all MSDS's
that are copied and distributed for this product.
Components present which could require a warning under
this statute are: NONE.


SECTION 16: OTHER INFORMATION.

Hazard Rating (HMIS):

Health: 1 0: minimal
Fire: 0 Where 1: slight
Reactivity: 0 2: moderate
3: serious
4: severe

This Material Safety Data Sheet complies with and is issued pursuant to 29 CFR 1910.1200
OSHA Hazard Communication Standard and is to be used solely for the purpose specified
therein.

This data is offered in good faith as typical values and not as a product specification. No
warranty, either expressed or implied, is made. The recommended handling procedures are
believed to be generally applicable, however, each user should review these recommendations
in the specific content for the intended use.

Search    ENTER KEYWORD
ALL Chemical Property And Toxicity Analysis PAGES IN THIS GROUP
NAMECAS
inktech-international_com---msds_res-1800.asp 145-04-0
inktech-international_com---msds_res-ink.asp 48145-04-6 00105-59-9
inktech-international_com---msds_sco-1800.asp 8052-41-3
inktech-international_com---msds_sco-1820.asp 64742-94-5
inktech-international_com---msds_sco_ink.asp 8052-41-3
inktech-international_com---msds_scs-2010.asp 111-76-2 64742-95-6 872-50-4
inktech-international_com---msds_scs-3010.asp 1310-73-2 5989-27-5 9002-93-1
inktech-international_com---msds_scs-3020.asp 1310-73-2 5989-27-5 111-90-0 9002-93-1
inktech-international_com---msds_stp-1800.asp 8052-41-3 64742-95-6
inktech-international_com---msds_stp-1820.asp 64741-68-0
inktech-international_com---msds_stp_no_lead.asp 8052-41-3 64742-95-6
inktech-international_com---msds_stp_with_lead.asp 8052-41-3 64742-95-6 1344-37-2
inktech-international_com---msds_super_stripper.asp 7790-28-5
inktech-international_com---msds_tf-1800.asp 48145-04-8
inktech-international_com---msds_tf-ink.asp 2235-00-9
inktech-international_com---msds_tyv-1800.asp 64742-95-6 111-76-2 123-42-2 96-48-0
inktech-international_com---msds_tyv_no_lead.asp 123-42-2 2807-30-9 111-76-2 64742-95-6 85-68-7
inktech-international_com---msds_tyv_with_lead.asp 123-42-2 2807-30-9 111-76-2 64742-95-6 85-68-7 7758-97-6
inktech-international_com---msds_xr-1800.asp 145-04-0
inktech-international_com---msds_xr-ink.asp 48145-04-6 00105-59-9
inktech-international_com---msds_xrs-1800.asp 145-04-0
inktech-international_com---msds_xrs-ink.asp 48145-04-6 00105-59-9
inlandcoatings_com---msd1000s.asp 64741-41-9 64742-95-6 1330-20-7 98-82-8 95-63-6
inlandcoatings_com---msd2030.asp 34590-94-8
inlandcoatings_com---msd2100c.asp 64742-48-9 64742-95-6 1330-20-7 98-82-8 95-63-6
inlandcoatings_com---msd2200b.asp 64742-48-9 64742-95-6 1330-20-7 98-82-8 95-63-6
inlandcoatings_com---msd2200s.asp 64742-48-9 64742-95-6 1330-20-7 98-82-8 95-63-6
inlandcoatings_com---msd2200t.asp 64742-48-9 64742-95-6 1330-20-7 98-82-8 95-63-6
inlandcoatings_com---msd300.asp 6834-92-0 68439-46-3 7732-18-5
inlandcoatings_com---msdrpm.asp N/A
inlandcoatings_com---msdrst.asp N/A
interchim_com---b-453-508-etalons.asp 122-40-7 100-51-6 104-54-1 5392-40-5 97-53-0 107-75-5 97-54-1 101-85-9 118-58-1 104-55-2 91-64-5 106-24-1 31906-04-4 105-13-5 103-41-3 4602-84-0 80-54-6 78-70-6 120-51-4 106-22-9 101-86-0 5989-27-5 111-12-6 127-51-5 97676-35-2 57-06-7 140-29-4 98-54-4 141-05-9 119-84-6 617-54-9 141-10-6 122-39-4 140-88-5 18829-55-5 67746-30-9 18318-83-7 26266-77-3 622-62-8 943-88-4 104-27-8 623-43-8
isco_com---redisep-alumina-neutral-msds.asp 1344-28-1
isco_com---redisep-silica-msds.asp 7631-86-9
isco_com---tn01_flowcell_care_and_cleaning_for_combiflash_companion.asp N/A
isco_com---up000zo7.asp N/A
isco_com---up0011ap.asp N/A
isotope_com---envcat.06_lores_unpriced.asp N/A
kmf_pa_msu_edu---nafion_117.asp N/A
kmf_pa_msu_edu---polyimideadhesionpromoter_vm652.asp 107-98-2 1589-47-5
kmf_pa_msu_edu---polyimidethinner_t9039.asp 872-50-4 107-98-2
makingcosmetics_com---msds-alkyl-sulfonate.asp 85711-69-9
makingcosmetics_com---msds-almond-oil.asp 8007-69-0
makingcosmetics_com---msds-aloe-vera-powder.asp 85507-69-3
makingcosmetics_com---msds-alpha-arbutin.asp 84380-01-8
makingcosmetics_com---msds-alpha-hydroxy-fruit-acids.asp 79-14-1
makingcosmetics_com---msds-aluminum-chlorohydrate.asp 12042-91-0
makingcosmetics_com---msds-argireline.asp 616204-22-9
makingcosmetics_com---msds-avobenzone.asp 70356-09-1
makingcosmetics_com---msds-avocado-butter.asp 91770-40-0

Free MSDS Search ( Providing 250,000+ Material Properties )
Chemcas.com | Ads link:HBCCHEM.INC