PLUMBERS MORTAR
PRODUCT NAME
1. IDENTIFICATION OF THE MATERIAL AND SUPPLIER
Supplier Name BLUE CIRCLE SOUTHERN CEMENT LIMITED
Address Clunies Ross Street, Prospect, NSW, AUSTRALIA, 2148
Telephone (02) 9033 4000
Fax (02) 9033 4055
Emergency 1800 033 111
Email
Web Site http://www.bluecirclesoutherncement.com.au
Synonym(s) BLUE CIRCLE SOUTHERN PLUMBERS MORTAR, MORTALOK FOR PLUMBERS
Use(s) CEMENT, INDUSTRIAL APPLICATIONS
2. HAZARDS IDENTIFICATION
CLASSIFIED AS HAZARDOUS ACCORDING TO NOHSC CRITERIA
NOT CLASSIFIED AS A DANGEROUS GOOD BY THE CRITERIA OF THE ADG CODE
UN No. None Allocated Hazchem Code Pkg Group
None Allocated None Allocated
DG Class None Allocated Subsidiary Risk(s) EPG None Allocated
None Allocated
3. COMPOSITION / INFORMATION ON INGREDIENTS
Ingredient Formula Conc. CAS No.
SILICA, CRYSTALLINE - QUARTZ Si-O2 >60% 14808-60-7
PORTLAND CEMENT Not Available 30-60% 65997-15-1
ADDITIVES Not Available <10% Not Available
CALCIUM ALUMINATE CEMENT Not Available <10% 65997-16-2
FIRECLAY Not Available <10% 130498-21-4
FLY ASH Not Available <10% 68131-74-8
GROUND BLAST FURNACE SLAG Not Available <10% 65997-69-2
HYDRATED LIME Not Available <10% Not Available
HEXAVALENT CHROMIUM (CONTAMINANT) Not Available Not Available Not Available
4. FIRST AID MEASURES
Eye Hold eyelids apart and flush continuously with water. Continue until advised to stop by the Poisons Information
Centre, a doctor, or for at least 15 minutes. Keep patient calm.
Inhalation If over exposure occurs leave exposure area immediately. If irritation persists, seek medical attention.
Skin Gently flush affected areas with water.
Ingestion For advice, contact a Poisons Information Centre on 13 11 26 (Australia Wide) or a doctor. If swallowed, do not
induce vomiting. Ingestion is considered unlikely due to product form.
Advice to Treat symptomatically
Doctor
First Aid Eye wash facilities should be available.
Facilities
Page 1 of 5
RMT
Reviewed: 01 May 2006
Printed: 25 May 2006
PLUMBERS MORTAR
PRODUCT NAME
5. FIRE FIGHTING MEASURES
Flammability Non flammable. No fire or explosion hazard exists.
Fire and Non flammable. No fire or explosion hazard exists.
Explosion
Extinguishing Non flammable.
Hazchem Code None
6. ACCIDENTAL RELEASE MEASURES
Spillage If spilt (bulk), wear PVC/rubber gloves, coveralls and a Full-face Class P3 (Particulate) respirator. At high dust
levels, wear an Air-line respirator. Spray with water to prevent dust generation and place in sealable containers for
disposal.
7. STORAGE AND HANDLING
Storage Store in cool, dry, well ventilated area, removed from moisture, oxidising agents (eg. hydrogen fluoride,
phosphorus oxide), acids, ethanol, interhalogens (eg. chlorine trifluoride) and foodstuffs. Ensure packages are
adequately labelled, protected from physical damage and sealed when not in use.
Handling Before use carefully read the product label. Use of safe work practices are recommended to avoid eye or skin
contact and inhalation. Observe good personal hygiene, including washing hands before eating. Prohibit eating,
drinking and smoking in contaminated areas (eg. if container is damaged).
8. EXPOSURE CONTROLS / PERSONAL PROTECTION
Ventilation Do not inhale dust. Use in well ventilated areas. In poorly ventilated areas, mechanical extraction ventilation is
recommended.Maintain dust levels below the recommended exposure standard.
Exposure SILICA, CRYSTALLINE - QUARTZ (14808-60-7)
ES-TWA: 0.1 mg/m3 (Silica Quartz, respirable, NOHSC)
Standards
ES-TWA#: 0.1 mg/m3 (QLD); 0.15 mg/m3 (NSW)
WES-TWA: 0.2 mg/m3
PORTLAND CEMENT (65997-15-1)
ES-TWA: 10 mg/m3 Portland Cement
ES-TWA#: 0.05 mg/m3 Chromium (VI) Compounds (contaminant)
WES-TWA: 10 mg/m3
CALCIUM ALUMINATE CEMENT (65997-16-2)
ES-TWA: 10 mg/m3 (total dust)
HEXAVALENT CHROMIUM (CONTAMINANT) (Not Available)
ES-TWA: 0.05 mg/m3.
PPE Wear dust-proof goggles and rubber or PVC gloves. Where heavy skin contamination is likely wear coveralls.
Where an inhalation risk exists, wear a Class P1 (Particulate) respirator. At high dust levels, wear a Full-Face
Class P3 (Particulate) or Powered Air Purifying Respirator (PAPR).
Page 2 of 5
RMT
Reviewed: 01 May 2006
Printed: 25 May 2006
PLUMBERS MORTAR
PRODUCT NAME
9. PHYSICAL AND CHEMICAL PROPERTIES
Appearance: GREY GRANULAR POWDER Solubility (water): < 10 g/L
Odour: SLIGHT ODOUR Specific Gravity: NOT AVAILABLE
pH: 11 - 13 % Volatiles: NOT AVAILABLE
Vapour Pressure: NOT AVAILABLE Flammability: NON FLAMMABLE
Vapour Density: NOT AVAILABLE Flash Point: NOT RELEVANT
Boiling Point: NOT AVAILABLE Upper Explosion Limit: NOT RELEVANT
Melting Point: 1200 C Lower Explosion Limit: NOT RELEVANT
Evaporation Rate: NOT AVAILABLE Autoignition Temperature: NOT AVAILABLE
Exposure Standard: 0.1 mg/m3 Crystalline silica quartz (respirable)
10. STABILTY AND REACTIVITY
Reactivity Incompatible with oxidising agents (eg hypochlorites), ethanol, acids (eg hydrofluoric acid) and interhalogens (eg
chlorine trifluoride). Water contact may increase product temperature 2-3 C.
Decomposition May evolve toxic gases if heated to decomposition.
Products
11. TOXICOLOGICAL INFORMATION
Health Hazard Slightly corrosive - irritant. Use safe work practices to avoid dust generation-inhalation. Workers exposed to
respirable crystalline silica dust in hard rock mining, sandblasting & granite cutting operations have been reported
Summary
to develop lung disease (silicosis) 2-30 years after exposure. Crystalline quartz is classified as carcinogenic to
humans (IARC Group 1). When wet, the potential for dust inhalation is minimal.
Eye Slightly corrosive - irritant. Exposure may result in lacrimation, pain, redness and possible corneal burns with
prolonged contact.
Inhalation Irritant - slightly corrosive. Over exposure at high levels may result in irritation of the nose and throat with
coughing. Prolonged and repeated inhalation of respirable silica may result in pulmonary fibrosis (silicosis).
Crystalline quartz is classified as carcinogenic to humans (IARC Group 1).
Skin Slightly corrosive. Prolonged and repeated contact with powder or wetted form may result in skin rash, dermatitis
and sensitisation.
Ingestion Slightly corrosive. Ingestion may result in burns to the mouth and throat, with vomiting and abdominal pain. Due to
product form, ingestion is not considered a likely exposure route.
Toxicity Data SILICA, CRYSTALLINE - QUARTZ (14808-60-7)
Carcinogenicity: Classified as a human carcinogen (IARC Group 1)
HEXAVALENT CHROMIUM (CONTAMINANT) (Not Available)
Carcinogenicity: Confirmed human carcinogen (IARC Group 1)
Health Surveillance: Required [NOHSC:1005(1994)]
12. ECOLOGICAL INFORMATION
Environment Limited ecotoxicity data was available for this product at the time this report was prepared. Ensure appropriate
measures are taken to prevent this product from entering the environment.
13. DISPOSAL CONSIDERATIONS
Waste Disposal Reuse or recycle where possible. Alternatively, ensure product is covered with moist soil to prevent dust
generation and dispose of to an approved landfill site. Contact the manufacturer for additional information.
Legislation Dispose of in accordance with relevant local legislation.
Page 3 of 5
RMT
Reviewed: 01 May 2006
Printed: 25 May 2006
PLUMBERS MORTAR
PRODUCT NAME
14. TRANSPORT INFORMATION
Shipping Name None Allocated
UN No. None Allocated Hazchem Code None Allocated Pkg Group None Allocated
DG Class None Allocated Subsidiary Risk(s) None Allocated EPG None Allocated
15. REGULATORY INFORMATION
Poison A poison schedule number has not been allocated to this product using the criteria in the Standard for the
Schedule Uniform Scheduling of Drugs and Poisons (SUSDP).
AICS All chemicals listed on the Australian Inventory of Chemical Substances (AICS).
16. OTHER INFORMATION
Additional RESPIRATORS: In general the use of respirators should be limited and engineering controls employed to avoid
exposure. If respiratory equipment must be worn ensure correct respirator selection and training is undertaken.
Information
Remember that some respirators may be extremely uncomfortable when used for long periods. The use of air
powered or air supplied respirators should be considered where prolonged or repeated use is necessary.
ABBREVIATIONS:
mg/m3 - Milligrams per cubic metre
ppm - Parts Per Million
TWA/ES - Time Weighted Average or Exposure Standard.
CNS - Central Nervous System
NOS - Not Otherwise Specified
pH - relates to hydrogen ion concentration - this value will relate to a scale of 0 - 14, where 0 is highly acidic and
14 is highly alkaline.
CAS# - Chemical Abstract Service number - used to uniquely identify chemical compounds.
M - moles per litre, a unit of concentration.
IARC - International Agency for Research on Cancer.
PERSONAL PROTECTIVE EQUIPMENT GUIDELINES:
The recommendation for protective equipment contained within this Chem Alert report is provided as a guide
only. Factors such as method of application, working environment, quantity used, product concentration and the
availability of engineering controls should be considered before final selection of personal protective equipment is
made.
HEALTH EFFECTS FROM EXPOSURE:
It should be noted that the effects from exposure to this product will depend on several factors including:
frequency and duration of use; quantity used; effectiveness of control measures; protective equipment used and
method of application. Given that it is impractical to prepare a Chem Alert report which would encompass all
possible scenarios, it is anticipated that users will assess the risks and apply control methods where appropriate.
Page 4 of 5
RMT
Reviewed: 01 May 2006
Printed: 25 May 2006
PLUMBERS MORTAR
PRODUCT NAME
Report Status This document has been compiled by RMT on behalf of the manufacturer of the product and serves as the
manufacturer's Material Safety Data Sheet ('MSDS').
It is based on information concerning the product which has been provided to RMT by the manufacturer or
obtained from third party sources and is believed to represent the current state of knowledge as to the
appropriate safety and handling precautions for the product at the time of issue. Further clarification regarding
any aspect of the product should be obtained directly from the manufacturer.
While RMT has taken all due care to include accurate and up-to-date information in this MSDS, it does not
provide any warranty as to accuracy or completeness. As far as lawfully possible, RMT accepts no liability for any
loss, injury or damage (including consequential loss) which may be suffered or incurred by any person as a
consequence of their reliance on the information contained in this MSDS.
Prepared By Risk Management Technologies
5 Ventor Ave, West Perth
Western Australia 6005
Phone: +61 8 9322 1711
Fax: +618 9322 1794
Email: info@rmt.com.au
Web: www.rmt.com.au
Last Reviewed: 01 May 2006
Date Printed: 25 May 2006
End of Report
Page 5 of 5
RMT
Reviewed: 01 May 2006
Printed: 25 May 2006
|