Search   
MSDS 
:
 Molybdenum(v) chloride, 98%
CAS 
:
 10241-05-1
SYNONYMS 
:
 Molybdenum pentachloride
**** SECTION 2 - COMPOSITION, INFORMATION ON INGREDIENTS ****

+----------------+--------------------------------------+----------+-----------+
| CAS# | Chemical Name | % | EINECS# |
|----------------|--------------------------------------|----------|-----------|
| 10241-05-1 |Molybdenum(V) chloride | 98.0 | 233-575-3 |
+----------------+--------------------------------------+----------+-----------+
Hazard Symbols: C
Risk Phrases: 14 34

**** SECTION 3 - HAZARDS IDENTIFICATION ****

EMERGENCY OVERVIEW
Reacts violently with water. Causes burns.Corrosive.Hygroscopic
(absorbs moisture from the air).

Potential Health Effects
Eye:
Causes severe eye irritation and burns.
Skin:
Causes severe skin irritation and burns.
Ingestion:
Causes gastrointestinal tract burns. May cause central nervous
system effects.
Inhalation:
May cause severe irritation of the respiratory tract with sore
throat, coughing, shortness of breath and delayed lung edema. Causes
chemical burns to the respiratory tract.
Chronic:
No information found.

**** SECTION 4 - FIRST AID MEASURES ****

Eyes:
Immediately flush eyes with plenty of water for at least 15 minutes,
occasionally lifting the upper and lower eyelids. Get medical aid
immediately. Do NOT allow victim to rub eyes or keep eyes closed.
Extensive irrigation with water is required (at least 30 minutes).
Skin:
Get medical aid immediately. Flush skin with plenty of water for at
least 15 minutes while removing contaminated clothing and shoes.
Discard contaminated clothing in a manner which limits further
exposure.
Ingestion:
Never give anything by mouth to an unconscious person. Get medical
aid immediately. Do NOT induce vomiting. If conscious and alert,
rinse mouth and drink 2-4 cupfuls of milk or water.
Inhalation:
Get medical aid immediately. Remove from exposure and move to fresh
air immediately. If not breathing, give artificial respiration. If
breathing is difficult, give oxygen. Do NOT use mouth-to-mouth
resuscitation.
Notes to Physician:

**** SECTION 5 - FIRE FIGHTING MEASURES ****

General Information:
As in any fire, wear a self-contained breathing apparatus in
pressure-demand, MSHA/NIOSH (approved or equivalent), and full
protective gear. During a fire, irritating and highly toxic gases
may be generated by thermal decomposition or combustion. Vapors may
be heavier than air. They can spread along the ground and collect
in low or confined areas. Contact with metals may evolve flammable
hydrogen gas. Containers may explode when heated or if contaminated
with water. Substance will react with water (some violently)
releasing flammable, toxic, or corrosive gases and runoff.
Combustible material; may burn but does not ignite readily.
Extinguishing Media:
Do NOT use straight streams of water. Most foams will react with the
material and release corrosive/toxic gases. Use dry chemical, dry
sand, or carbon dioxide.

**** SECTION 6 - ACCIDENTAL RELEASE MEASURES ****

General Information: Use proper personal protective equipment as indicated
in Section 8.
Spills/Leaks:
Avoid runoff into storm sewers and ditches which lead to waterways.
Clean up spills immediately, observing precautions in the Protective
Equipment section. Sweep up, then place into a suitable container for
disposal. Avoid generating dusty conditions. Remove all sources of
ignition. Provide ventilation. A vapor suppressing foam may be used
to reduce vapors. Stop leak only if you can do so without risk.

**** SECTION 7 - HANDLING and STORAGE ****

Handling:
Use only in a well-ventilated area. Minimize dust generation and
accumulation. Ground and bond containers when transferring material.
Keep container tightly closed. Do not get on skin or in eyes. Do not
ingest or inhale. Discard contaminated shoes.
Storage:
Store in a cool, dry, well-ventilated area away from incompatible
substances. Corrosives area. Keep containers tightly closed.

**** SECTION 8 - EXPOSURE CONTROLS, PERSONAL PROTECTION ****

Engineering Controls:
Use adequate general or local exhaust ventilation to keep airborne
concentrations below the permissible exposure limits.
Exposure Limits
CAS# 10241-05-1:
United States OSHA: 15 mg/m3 TWA (total dust) (listed under
Molybdenum).
Malaysia: (listed as molybdenum): 10 mg/m3 TWA
Netherlands: (listed as molybdenum): 5 mg/m3 MAC
Russia: (listed as molybdenum): 3 mg/m3 TWA
Russia: (listed as molybdenum): 0.5 mg/m3 STEL

Personal Protective Equipment

Eyes:
Wear appropriate protective eyeglasses or chemical
safety goggles as described by OSHA's eye and face
protection regulations in 29 CFR 1910.133 or European
Standard EN166.
Skin:
Wear appropriate protective gloves to prevent skin
exposure.
Clothing:
Wear appropriate protective clothing to prevent skin
exposure.
Respirators:
Follow the OSHA respirator regulations found in 29
CFR 1910.134 or European Standard EN 149. Use a
NIOSH/MSHA or European Standard EN 149 approved
respirator if exposure limits are exceeded or if
irritation or other symptoms are experienced.

**** SECTION 9 - PHYSICAL AND CHEMICAL PROPERTIES ****

Physical State: Solid
Color: green, blue, steel gray or black
Odor: None reported.
pH: Not available.
Vapor Pressure: 1.75 mmHg @ 25
Viscosity: Not available.
Boiling Point: 268 deg C @ 760.00mmHg
Freezing/Melting Point: 194 deg C
Autoignition Temperature: Not available.
Flash Point: Not available.
Explosion Limits, lower: Not available.
Explosion Limits, upper: Not available.
Decomposition Temperature:
Solubility in water: reacts
Specific Gravity/Density: 2.9280g/cm3
Molecular Formula: Cl5Mo
Molecular Weight: 273.20

**** SECTION 10 - STABILITY AND REACTIVITY ****

Chemical Stability:
Reacts with water to form toxic fumes. Unstable in air.
Conditions to Avoid:
Incompatible materials, dust generation, exposure to moist air or
water.
Incompatibilities with Other Materials:
Water, strong oxidizing agents.
Hazardous Decomposition Products:
Hydrogen chloride, chlorine.
Hazardous Polymerization: Has not been reported.

**** SECTION 11 - TOXICOLOGICAL INFORMATION ****

RTECS#:
CAS# 10241-05-1: QA4690000
LD50/LC50:
Not available.
Carcinogenicity:
Molybdenum(V) chloride -
Not listed by ACGIH, IARC, or NTP.
Other:
See actual entry in RTECS for complete information.

**** SECTION 12 - ECOLOGICAL INFORMATION ****



**** SECTION 13 - DISPOSAL CONSIDERATIONS ****

Dispose of in a manner consistent with federal, state, and local regulations.

**** SECTION 14 - TRANSPORT INFORMATION ****

IATA
Shipping Name: MOLYBDENUM PENTACHLORIDE
Hazard Class: 8
UN Number: 2508
Packing Group: III
IMO
Shipping Name: MOLYBDENUM PENTACHLORIDE
Hazard Class: 8
UN Number: 2508
Packing Group: III
RID/ADR
Shipping Name: MOLYBDENUM PENTACHLORIDE
Hazard Class: 8
UN Number: 2508
Packing group: III

**** SECTION 15 - REGULATORY INFORMATION ****

European/International Regulations
European Labeling in Accordance with EC Directives
Hazard Symbols: C
Risk Phrases:
R 14 Reacts violently with water.
R 34 Causes burns.
Safety Phrases:
S 7/8 Keep container tightly closed and dry.
S 26 In case of contact with eyes, rinse immediately
with plenty of water and seek medical advice.
WGK (Water Danger/Protection)
CAS# 10241-05-1: No information available.
Canada
CAS# 10241-05-1 is listed on Canada's NDSL List.
CAS# 10241-05-1 is not listed on Canada's Ingredient Disclosure List.
US FEDERAL
TSCA
CAS# 10241-05-1 is listed on the TSCA inventory.

**** SECTION 16 - ADDITIONAL INFORMATION ****

MSDS Creation Date: 9/04/1998 Revision #2 Date: 3/18/2003

The information above is believed to be accurate and represents the best
information currently available to us. However, we make no warranty of
merchantability or any other warranty, express or implied, with respect to
such information, and we assume no liability resulting from its use. Users
should make their own investigations to determine the suitability of the
information for their particular purposes. In no way shall the company be
liable for any claims, losses, or damages of any third party or for lost
profits or any special, indirect, incidental, consequential or exemplary
damages, howsoever arising, even if the company has been advised of
the possibility of such damages.
--------------------------------------------------------------------------------
--------------------------------------------------------------------------------
Search More   
ALL MSDS PAGES IN THIS GROUP
NAMECAS
l-Cysteic Acid Monohydrate, 99+% 23537-25-9
1-Hexanesulfonic acid sodium salt premixed concentrate
N-Alpha-Carbobenzyloxy-L-Asparagine, 98% 2304-96-3
Ytterbium atomic absorption standard solution, 1 mg/ml yb in 2% hno3
Bromotrichloromethane, 99% 75-62-7
Dicyclopentadiene, 95%, stabilized with 100-200 ppm 77-73-6
3-Amino-1-propanesulfonic acid, 95% 3687-18-1
Copper(ii) fluoride, anhydrous, 99+% 7789-19-7
2-Chloro-4-Fluorophenylacetic Acid 177985-32-9
Cyclopropyl Phenyl Sulfide 14633-54-6
BOC-L-Tyrosine, 99+% 3978-80-1
1,8-Octanediol, 99+% 629-41-4
3-Thiophenecarboxylic acid, 99% 88-13-1
1,2,3-Trimethylbenzene, Tech., 90% 526-73-8
Molybdenum(v) chloride, 98% 10241-05-1
2-Dimethylaminoethyl Acetate 1421-89-2
4-Benzyl-4-Hydroxypiperidine, 95+%(GC) 51135-96-7
8-Chloroquinoline, 99% (gc) 611-33-6
2-Ethyl-3,5(6)-dimethylpyrazine,99.5+% 27043-05-6
p-Ethoxybenzyl Alcohol, 98% 6214-44-4
2,3-Dichlorothiophene, 97% 17249-79-5
Tropolone, 98% 533-75-5
1,3-Difluorobenzene, 99+% 372-18-9
2-Methylundecanal, 95% 110-41-8
2-Ethyl-2-methyl-1,3-dioxolane, 99% 126-39-6
Bromoethane, 98% 74-96-4
1,3,5-Triphenylbenzene, 97% 612-71-5
1-Tetradecene, 92% 1120-36-1
9,10-Anthracenedicarboxaldehyde, 95% (UV-Vis) 7044-91-9
Lead cyclohexanebutyrate 62637-99-4
1-Butanethiol, 99+% 109-79-5
L-(+)-Homoarginine hydrochloride, 99+% 1483-01-8
3,4-(Methylenedioxy)-aniline, 97% 14268-66-7
(2-Chloroethyl)benzene, 99% 622-24-2
Poly(propylene), chlorinated 68442-33-1
Dodecyl aldehyde, 96%, stabilized with 0.1% BHA 112-54-9
N,N'-Diallyltartardiamide 58477-85-3
5,6,7,8-Tetrahydro-2-naphthol, 98% 1125-78-6
Cyclodecanone, 97% 1502-06-3
4-Amino-1-butanol, 98% 13325-10-5
4-Aminoveratrole, 98% 6315-89-5
2-Bromo-4-nitrotoluene, 98% 7745-93-9
Pulegone (Pract), 88% (GC) 89-82-7
Diethyl suberate, 98% 2050-23-9
beta-Bromostyrene, mixture of cis/trans isomers, 97% 103-64-0
Naphthenic acids (pract) 1338-24-5
S(+)-1,3-Butanediol, 98% 24621-61-2
5-Bromo-1,2,4-trimethylbenzene, 99% 5469-19-2
alpha-D(+)-Melibiose hydrate, 99+% 585-99-9
O-Tolualdehyde 98% (Stabilized with 0.1 % H.Q.) 529-20-4

Free MSDS Search ( Providing 250,000+ Material Properties )
Chemcas.com| Ads link:todaystock.net