**** SECTION 2 - COMPOSITION, INFORMATION ON INGREDIENTS ****
+----------------+--------------------------------------+----------+-----------+
| CAS# | Chemical Name | % | EINECS# |
|----------------|--------------------------------------|----------|-----------|
| 2807-30-9 |2-Propoxyethanol | 98 | 220-548-6 |
+----------------+--------------------------------------+----------+-----------+
Hazard Symbols: XN XI F
Risk Phrases: 10 21 36
**** SECTION 3 - HAZARDS IDENTIFICATION ****
EMERGENCY OVERVIEW
Flammable. Harmful in contact with skin. Irritating to eyes.
Potential Health Effects
Eye:
Causes severe eye irritation. May cause eye injury.
Skin:
Causes skin irritation. Harmful if absorbed through the skin.
Ingestion:
May cause irritation of the digestive tract. May cause liver and
kidney damage. May cause blood abnormalities. May be harmful if
swallowed.
Inhalation:
May cause respiratory tract irritation. Vapors may cause dizziness
or suffocation.
Chronic:
None
**** SECTION 4 - FIRST AID MEASURES ****
Eyes:
Flush eyes with plenty of water for at least 15 minutes,
occasionally lifting the upper and lower eyelids. Get medical aid
immediately.
Skin:
Get medical aid. Flush skin with plenty of water for at least 15
minutes while removing contaminated clothing and shoes.
Ingestion:
If victim is conscious and alert, give 2-4 cupfuls of milk or water.
Never give anything by mouth to an unconscious person. Get medical
aid immediately.
Inhalation:
Remove from exposure and move to fresh air immediately. If not
breathing, give artificial respiration. If breathing is difficult,
give oxygen. Get medical aid.
Notes to Physician:
**** SECTION 5 - FIRE FIGHTING MEASURES ****
General Information:
Containers can build up pressure if exposed to heat and/or fire. As
in any fire, wear a self-contained breathing apparatus in
pressure-demand, MSHA/NIOSH (approved or equivalent), and full
protective gear. Vapors may form an explosive mixture with air.
Vapors can travel to a source of ignition and flash back. Use water
spray to keep fire-exposed containers cool. Flammable liquid and
vapor. May form explosive peroxides. Vapors may be heavier than air.
They can spread along the ground and collect in low or confined
areas. May be ignited by heat, sparks, and flame.
Extinguishing Media:
For small fires, use dry chemical, carbon dioxide, water spray or
alcohol-resistant foam. Use water spray to cool fire-exposed
containers. Water may be ineffective. Do NOT use straight streams of
water. For large fires, use dry chemical, carbon dioxide,
alcohol-resistant foam, or water spray. Cool containers with
flooding quantities of water until well after fire is out.
**** SECTION 6 - ACCIDENTAL RELEASE MEASURES ****
General Information: Use proper personal protective equipment as indicated
in Section 8.
Spills/Leaks:
Absorb spill with inert material (e.g. vermiculite, sand or earth),
then place in suitable container. Remove all sources of ignition.
Provide ventilation. A vapor suppressing foam may be used to reduce
vapors. Water spray may reduce vapor but may not prevent ignition in
closed spaces.
**** SECTION 7 - HANDLING and STORAGE ****
Handling:
Wash thoroughly after handling. Use with adequate ventilation.
Ground and bond containers when transferring material. Avoid contact
with eyes, skin, and clothing. Empty containers retain product
residue, (liquid and/or vapor), and can be dangerous. Keep container
tightly closed. Keep away from heat, sparks and flame. Avoid
ingestion and inhalation. Do not pressurize, cut, weld, braze,
solder, drill, grind, or expose empty containers to heat, sparks or
open flames.
Storage:
Keep away from heat, sparks, and flame. Keep away from sources of
ignition. Store in a tightly closed container. Store in a cool, dry,
well-ventilated area away from incompatible substances. Regularly
check inhibitor levels to maintain peroxide levels below 1%. Storage
under a nitrogen blanket has been recommended.
**** SECTION 8 - EXPOSURE CONTROLS, PERSONAL PROTECTION ****
Engineering Controls:
Use adequate general or local explosion-proof ventilation to keep
airborne levels to acceptable levels.
Exposure Limits
CAS# 2807-30-9:
Germany: 20 ppm TWA; 86 mg/m3 TWA
Germany: Skin absorber
Netherlands: 10 ppm MAC; 44 mg/m3 MAC
Spain: 20 ppm VLA-ED; 86 mg/m3 VLA-ED
Personal Protective Equipment
Eyes:
Wear appropriate protective eyeglasses or chemical
safety goggles as described by OSHA's eye and face
protection regulations in 29 CFR 1910.133 or European
Standard EN166.
Skin:
Wear appropriate protective gloves to prevent skin
exposure.
Clothing:
Wear appropriate protective clothing to prevent skin
exposure.
Respirators:
Follow the OSHA respirator regulations found in 29
CFR 1910.134 or European Standard EN 149. Use a
NIOSH/MSHA or European Standard EN 149 approved
respirator if exposure limits are exceeded or if
irritation or other symptoms are experienced.
**** SECTION 9 - PHYSICAL AND CHEMICAL PROPERTIES ****
Physical State: Liquid
Color: clear yellow
Odor: ethereal odor
pH: Not available.
Vapor Pressure: 1.7 mbar @ 20 deg C
Viscosity: 2.42mPas
Boiling Point: 149.5 deg C
Freezing/Melting Point: -90 deg C
Autoignition Temperature: 230 deg C ( 446.00 deg F)
Flash Point: 125 deg F ( 51.67 deg C)
Explosion Limits, lower: 1.26 vol%
Explosion Limits, upper: 15.8 vol%
Decomposition Temperature:
Solubility in water: soluble in water
Specific Gravity/Density: .9130g/cm3
Molecular Formula: C5H12O2
Molecular Weight: 104.15
**** SECTION 10 - STABILITY AND REACTIVITY ****
Chemical Stability:
Stable under normal temperatures and pressures. On long term
storage, substances with similar functional groups form explosive
peroxides.
Conditions to Avoid:
High temperatures, incompatible materials, ignition sources, excess
heat.
Incompatibilities with Other Materials:
Strong oxidizing agents
Hazardous Decomposition Products:
Carbon monoxide, carbon dioxide.
Hazardous Polymerization: Will not occur.
**** SECTION 11 - TOXICOLOGICAL INFORMATION ****
RTECS#:
CAS# 2807-30-9: KM2800000
LD50/LC50:
CAS# 2807-30-9: Dermal, guinea pig: LD50 = 1 gm/kg; Draize test,
rabbit, eye: 100 mg Severe; Draize test, rabbit, eye: 750 ug/24H
Severe; Draize test, rabbit, skin: 500 mg/24H Mild; Inhalation,
mouse: LC50 = 1530 ppm/7H; Inhalation, rat: LC50 = 9060 mg/m3; Oral,
mouse: LD50 = 1774 mg/kg; Oral, rat: LD50 = 3089 mg/kg; Oral, rat:
LD50 = 3090 mg/kg; Skin, rabbit: LD50 = 960 uL/kg.
Oral, rat: LD50 = 1746-10502 mg/kg
Carcinogenicity:
2-Propoxyethanol -
Not listed by ACGIH, IARC, or NTP.
Other:
See actual entry in RTECS for complete information.
**** SECTION 12 - ECOLOGICAL INFORMATION ****
Ecotoxicity:
Fish: Fathead Minnow: >100ul/l; 96hr; LC50Daphnia: Water Flea:
>100ul/l; 96hr; LC50
**** SECTION 13 - DISPOSAL CONSIDERATIONS ****
Dispose of in a manner consistent with federal, state, and local regulations.
**** SECTION 14 - TRANSPORT INFORMATION ****
IATA
Shipping Name: FLAMMABLE LIQUID, N.O.S.*
Hazard Class: 3
UN Number: 1993
Packing Group: III
IMO
Shipping Name: FLAMMABLE LIQUID, N.O.S.
Hazard Class: 3.3
UN Number: 1993
Packing Group: III
RID/ADR
Shipping Name: FLAMMABLE LIQUID, N.O.S.
Hazard Class: 3
UN Number: 1993
Packing group: III
**** SECTION 15 - REGULATORY INFORMATION ****
European/International Regulations
European Labeling in Accordance with EC Directives
Hazard Symbols: XN XI F
Risk Phrases:
R 10 Flammable.
R 21 Harmful in contact with skin.
R 36 Irritating to eyes.
Safety Phrases:
S 24/25 Avoid contact with skin and eyes.
S 36/37 Wear suitable protective clothing and
gloves.
WGK (Water Danger/Protection)
CAS# 2807-30-9: 1
Canada
CAS# 2807-30-9 is listed on Canada's DSL List.
CAS# 2807-30-9 is not listed on Canada's Ingredient Disclosure List.
US FEDERAL
TSCA
CAS# 2807-30-9 is listed on the TSCA inventory.
**** SECTION 16 - ADDITIONAL INFORMATION ****
MSDS Creation Date: 10/02/1998 Revision #3 Date: 10/10/2003
The information above is believed to be accurate and represents the best
information currently available to us. However, we make no warranty of
merchantability or any other warranty, express or implied, with respect to
such information, and we assume no liability resulting from its use. Users
should make their own investigations to determine the suitability of the
information for their particular purposes. In no way shall the company be
liable for any claims, losses, or damages of any third party or for lost
profits or any special, indirect, incidental, consequential or exemplary
damages, howsoever arising, even if the company has been advised of
the possibility of such damages.
--------------------------------------------------------------------------------
--------------------------------------------------------------------------------
|
|
|
| ALL MSDS PAGES IN THIS GROUP
| | NAME | CAS |
|
Tridecanenitrile, 98%
| 629-60-7 |
|
Nitrosylsulfuric acid (40% in 87% sulfuric acid), 40%
| 7664-93-9 |
|
Nickel Cyclohexanebutyrate, min. 13.5%Ni
| 3906-55-6 |
|
4-Aminophenyl Sulfone, 97%
| 80-08-0 |
|
5-Fluorosalicylic Acid, 99%
| 345-16-4 |
|
4'-Bromo-3'-Nitroacetophenone, 99+%(TLC)
| 18640-58-9 |
|
1,3,5-Triethylhexahydro-S-Triazine, 97%
| 7779-27-3 |
|
Indole-3-Carbinol Hydrate, 99%
| 123334-15-6 |
|
3,5,5-Trimethylhexanoic acid, 95%(gc)
| 3302-10-1 |
|
3,4-Dimethoxybenzoic Acid, 99+%
| 93-07-2 |
|
2-Ethynylpyridine, 98+%
| 1945-84-2 |
|
Nitromethane
| 75-52-5 |
|
3,7-Dimethyl-2,6-Octadienenitrile, 97%, (Mixture of Isomers)
| 5146-66-7 |
|
Rhodium (III) Chloride, Anhydrous
| 10049-07-7 |
|
Methyl 4-Amino-1-Benzyl-1,2,5,6-Tetrahydropyridine-3-Carboxylate, 99%
| 0-01-1 |
|
Ruthenium on carbon 5% ruthenium, ca. 50% moisture
| |
|
5-Chloro-2-nitrobenzotrifluoride, 99%
| 118-79-6 |
|
4-Iodotoluene, 98%
| 624-31-7 |
|
Sodium Nitroprusside
| 14402-89-2 |
|
1,2,4-Butanetriol, 95%
| 3068-00-6 |
|
Ethyl dichlorophosphite, 98%
| 1498-42-6 |
|
L-(-)-Malic Acid, Disodium Salt Monohydrate, 98%
| 64887-73-6 |
|
Riboflavin 5'-Phosphate Sodium Salt, Dihydrate, 73.0-79.0% (on Dry
| 6184-17-4 |
|
3-Fluorophthalic anhydride, 98%
| 652-39-1 |
|
2,4-Thiazolidinedione, 99%
| 2295-31-0 |
|
Tris-Phosphate, 98%
| 6992-39-8 |
|
Mercurochrome, 24-27% Mercury (corrected for volatiles)
| 129-16-8 |
|
3-Bromophenylhydrazine Hydrochloride, 98%
| 27246-81-7 |
|
1,2-Diiodoethane, 99%
| 624-60-2 |
|
4-Methylbenzhydrol, 98%
| 1517-63-1 |
|
2-Propoxyethanol, 98% (gc)
| 2807-30-9 |
|
3,5-Dimethyl-p-anisic acid, 98%
| 21553-46-8 |
|
n-Methylisatin 3-(thiosemicarbazone), 96%
| 1910-68-5 |
|
Benzeneseleninic anhydride, 98%
| 17697-12-0 |
|
Sodium Sulfide Hydrate, 60-62%, scales
| 27610-45-3 |
|
N-(2-Chloroethyl)benzamide, 99%
| 26385-07-9 |
|
2-Chlorophenyl isothiocyanate, 99%
| 2740-81-0 |
|
4-Indanol, 98%
| 1641-41-4 |
|
1,4-Thioxane, 98%
| 15980-15-1 |
|
Quinine, anhydrous, 99% (titr)
| 130-95-0 |
|
Potassium Phosphate, Dibasic Trihydrate, 99+%
| 16788-57-1 |
|
Benzyl Methyl Sulfide, 98%
| 766-92-7 |
|
5-Nitro-2-furaldehyde, 99%
| 698-63-5 |
|
o-Cresol, 99+% (gc)
| 95-48-7 |
|
(+)-Octopine
| 34522-32-2 |
|
o-Dichlorobenzene
| 95-50-1 |
|
5,7-Dichloro-8-Hydroxyquinoline, 99%
| 773-76-2 |
|
3,3,5,5-Tetramethylcyclohexanol, 96%
| 2650-40-0 |
|
Pentafluoropyridine, 99+%
| 700-16-3 |
|
Perfluoro-1-iodohexane, 99%
| 355-43-1 |
|
|