Search   
MSDS 
:
 Dimethylthexylsilyl Chloride
CAS 
:
 67373-56-2
SYNONYMS 
:
 Thexyl-Dichloromethylsilane.
**** SECTION 2 - COMPOSITION, INFORMATION ON INGREDIENTS ****

+----------------+--------------------------------------+----------+-----------+
| CAS# | Chemical Name | % | EINECS# |
|----------------|--------------------------------------|----------|-----------|
| 67373-56-2 |Dimethylthexylsilyl Chloride | ca 100 | unlisted |
+----------------+--------------------------------------+----------+-----------+
Hazard Symbols: C
Risk Phrases: 10 34

**** SECTION 3 - HAZARDS IDENTIFICATION ****

EMERGENCY OVERVIEW
Flammable. Causes burns.Moisture sensitive.Corrosive.

Potential Health Effects
Eye:
Causes eye burns. May cause chemical conjunctivitis and corneal
damage.
Skin:
Causes skin burns. May cause irritation and dermatitis. May cause
cyanosis of the extremities. May cause skin rash (in milder cases),
and cold and clammy skin with cyanosis or pale color.
Ingestion:
May cause severe and permanent damage to the digestive tract. May
cause gastrointestinal irritation with nausea, vomiting and
diarrhea. Causes gastrointestinal tract burns. May cause perforation
of the digestive tract. The toxicological properties of this
substance have not been fully investigated. Ingestion of large
amounts may cause CNS depression. May cause systemic effects.
Inhalation:
Causes chemical burns to the respiratory tract. The toxicological
properties of this substance have not been fully investigated.
Aspiration may lead to pulmonary edema. Vapors may cause dizziness or
suffocation. May cause systemic effects. May cause burning sensation
in the chest.
Chronic:
Effects may be delayed.

**** SECTION 4 - FIRST AID MEASURES ****

Eyes:
Get medical aid immediately. Do NOT allow victim to rub eyes or keep
eyes closed. Extensive irrigation with water is required (at least 30
minutes).
Skin:
Get medical aid immediately. Immediately flush skin with plenty of
water for at least 15 minutes while removing contaminated clothing
and shoes. Wash clothing before reuse. Destroy contaminated shoes.
Ingestion:
Get medical aid. Do NOT induce vomiting. If conscious and alert,
rinse mouth and drink 2-4 cupfuls of milk or water.
Inhalation:
Remove from exposure and move to fresh air immediately. If not
breathing, give artificial respiration. If breathing is difficult,
give oxygen. Get medical aid. Do NOT use mouth-to-mouth
resuscitation. If breathing has ceased apply artificial respiration
using oxygen and a suitable mechanical device such as a bag and a
mask.
Notes to Physician:

**** SECTION 5 - FIRE FIGHTING MEASURES ****

General Information:
As in any fire, wear a self-contained breathing apparatus in
pressure-demand, MSHA/NIOSH (approved or equivalent), and full
protective gear. Vapors may form an explosive mixture with air.
Vapors can travel to a source of ignition and flash back. During a
fire, irritating and highly toxic gases may be generated by thermal
decomposition or combustion. Use water spray to keep fire-exposed
containers cool. Water may be ineffective. Material is lighter than
water and a fire may be spread by the use of water. Containers may
explode in the heat of a fire. Flammable liquid and vapor. Vapors
may be heavier than air. They can spread along the ground and
collect in low or confined areas.
Extinguishing Media:
For small fires, use dry chemical, carbon dioxide, water spray or
alcohol-resistant foam. For large fires, use water spray, fog, or
alcohol-resistant foam. Use water spray to cool fire-exposed
containers. Water may be ineffective. Do NOT get water inside
containers. Do NOT use straight streams of water.

**** SECTION 6 - ACCIDENTAL RELEASE MEASURES ****

General Information: Use proper personal protective equipment as indicated
in Section 8.
Spills/Leaks:
Absorb spill with inert material (e.g. vermiculite, sand or earth),
then place in suitable container. Avoid runoff into storm sewers and
ditches which lead to waterways. Clean up spills immediately,
observing precautions in the Protective Equipment section. Remove all
sources of ignition. Use a spark-proof tool. Provide ventilation. Do
not get water inside containers. A vapor suppressing foam may be
used to reduce vapors.

**** SECTION 7 - HANDLING and STORAGE ****

Handling:
Remove contaminated clothing and wash before reuse. Use with
adequate ventilation. Ground and bond containers when transferring
material. Use spark-proof tools and explosion proof equipment. Avoid
contact with eyes, skin, and clothing. Empty containers retain
product residue, (liquid and/or vapor), and can be dangerous. Keep
container tightly closed. Keep away from heat, sparks and flame.
Avoid ingestion and inhalation. Use with adequate ventilation. Do
not allow contact with water. Discard contaminated shoes. Do not
pressurize, cut, weld, braze, solder, drill, grind, or expose empty
containers to heat, sparks or open flames. Keep from contact with
moist air and steam.
Storage:
Keep away from heat, sparks, and flame. Keep away from sources of
ignition. Store in a tightly closed container. Store in a cool, dry,
well-ventilated area away from incompatible substances.
Flammables-area. Storage under a nitrogen blanket has been
recommended. Store protected from moisture.

**** SECTION 8 - EXPOSURE CONTROLS, PERSONAL PROTECTION ****

Engineering Controls:
Facilities storing or utilizing this material should be equipped
with an eyewash facility and a safety shower. Use adequate general or
local explosion-proof ventilation to keep airborne levels to
acceptable levels.
Exposure Limits
CAS# 67373-56-2:
United Kingdom, WEL - TWA: (listed as silica, amorphous): 6 mg/m3
(inhalable dust); 2.4 mg/m3 TWA (respirable dust)
United Kingdom, WEL - STEL: (listed as silica, amorphous): 18 mg/
STEL (inhalable dust); 7.2 mg/m3 STEL (respirable dust)

Russia: (listed as silica, amorphous): 1 mg/m3 TWA

Personal Protective Equipment

Eyes:
Wear appropriate protective eyeglasses or chemical
safety goggles as described by OSHA's eye and face
protection regulations in 29 CFR 1910.133 or European
Standard EN166.
Skin:
Wear appropriate protective gloves to prevent skin
exposure.
Clothing:
Wear appropriate protective clothing to prevent skin
exposure.
Respirators:
A respiratory protection program that meets OSHA's 29
CFR 1910.134 and ANSI Z88.2 requirements or European
Standard EN 149 must be followed whenever workplace
conditions warrant respirator use.

**** SECTION 9 - PHYSICAL AND CHEMICAL PROPERTIES ****

Physical State: Liquid
Color: colorless
Odor: Not available.
pH: Not available.
Vapor Pressure: Not available.
Viscosity: Not available.
Boiling Point: Not available.
Freezing/Melting Point: Not available.
Autoignition Temperature: Not available.
Flash Point: 46 deg C ( 114.80 deg F)
Explosion Limits, lower: Not available.
Explosion Limits, upper: Not available.
Decomposition Temperature:
Solubility in water:
Specific Gravity/Density: .9090g/cm3
Molecular Formula: C8H19ClSi
Molecular Weight: 178.78

**** SECTION 10 - STABILITY AND REACTIVITY ****

Chemical Stability:
Stable under normal temperatures and pressures.
Conditions to Avoid:
Incompatible materials, ignition sources, moisture, excess heat,
strong oxidants.
Incompatibilities with Other Materials:
Moisture, strong oxidizing agents.
Hazardous Decomposition Products:
Carbon monoxide, irritating and toxic fumes and gases, carbon
dioxide, oxides of chlorine, oxides of silicon.
Hazardous Polymerization: Has not been reported

**** SECTION 11 - TOXICOLOGICAL INFORMATION ****

RTECS#:
CAS# 67373-56-2 unlisted.
LD50/LC50:
Not available.
Carcinogenicity:
Dimethylthexylsilyl Chloride -
Not listed by ACGIH, IARC, or NTP.

**** SECTION 12 - ECOLOGICAL INFORMATION ****



**** SECTION 13 - DISPOSAL CONSIDERATIONS ****

Dispose of in a manner consistent with federal, state, and local regulations.

**** SECTION 14 - TRANSPORT INFORMATION ****

IATA
Shipping Name: CORROSIVE LIQUID, FLAMMABLE, N.O.S.*
Hazard Class: 8 (3)
UN Number: 2920
Packing Group: II
IMO
Shipping Name: CORROSIVE LIQUID, FLAMMABLE, N.O.S.
Hazard Class: 8 (3)
UN Number: 2920
Packing Group: II
RID/ADR
Shipping Name: CORROSIVE LIQUID, FLAMMABLE, N.O.S.
Hazard Class: 8
UN Number: 2920
Packing group: II

**** SECTION 15 - REGULATORY INFORMATION ****

European/International Regulations
European Labeling in Accordance with EC Directives
Hazard Symbols: C
Risk Phrases:
R 10 Flammable.
R 34 Causes burns.
Safety Phrases:
S 9 Keep container in a well-ventilated place.
S 16 Keep away from sources of ignition - No
smoking.
S 26 In case of contact with eyes, rinse immediately
with plenty of water and seek medical advice.
S 28A After contact with skin, wash immediately with
plenty of water.
S 33 Take precautionary measures against static
discharges.
S 37 Wear suitable gloves.
S 45 In case of accident or if you feel unwell, seek
medical advice immediately (show the label where
possible).
WGK (Water Danger/Protection)
CAS# 67373-56-2: No information available.
Canada
None of the chemicals in this product are listed on the DSL/NDSL list.
CAS# 67373-56-2 is not listed on Canada's Ingredient Disclosure List.
US FEDERAL
TSCA
CAS# 67373-56-2 is not listed on the TSCA inventory.
It is for research and development use only.

**** SECTION 16 - ADDITIONAL INFORMATION ****

MSDS Creation Date: 7/01/1999 Revision #2 Date: 3/18/2003

The information above is believed to be accurate and represents the best
information currently available to us. However, we make no warranty of
merchantability or any other warranty, express or implied, with respect to
such information, and we assume no liability resulting from its use. Users
should make their own investigations to determine the suitability of the
information for their particular purposes. In no way shall the company be
liable for any claims, losses, or damages of any third party or for lost
profits or any special, indirect, incidental, consequential or exemplary
damages, howsoever arising, even if the company has been advised of
the possibility of such damages.
--------------------------------------------------------------------------------
--------------------------------------------------------------------------------
Search More   
ALL MSDS PAGES IN THIS GROUP
NAMECAS
3-Dimethylaminoacrylonitrile, 99% 2407-68-3
(-)-8-Phenylmenthol, 98% 65253-04-5
4-Nitrophenyl Phosphate, Bis-(Cyclohexyl- Ammonium) Salt, 99+% 14545-82-5
3,3,5-Trimethylcyclohexanol,98% Mixture of Cis and Trans 116-02-9
L(-)-Phenylephrine Hydrochloride, 99% 61-76-7
(S)-(+)-2-Chloropropan-1-ol, 96% 19210-21-0
Dimethylthexylsilyl Chloride 67373-56-2
DL-Alanine, 99% 302-72-7
(-)-Menthyl lactate, 98% 59259-38-0
1,1-Diphenyl-2-Picrylhydrazine 1707-75-1
9-Nitroanthracene, 97% 602-60-8
Cis-Stilbene, 97% 645-49-8
2-Fluorobenzoyl Chloride, 97% 393-52-2
Alizarin Yellow R Sodium Salt, 96% (UV-VIS) 1718-34-9
Phenyl carbamate, 97% 622-46-8
m-Methoxybenzyl chloride, 97% 824-98-6
Methyl Violet 2B, Indicator Grade 8004-87-3
4,7-Diphenyl-1,10-Phenanthroline, 99% (UV-Vis) 1662-01-7
4'-Fluoro-2'-nitroacetanilide, 99+% 448-39-5
DL-2-Amino-4-Pentenoic Acid, 99+% 7685-44-1
4-Chloro-3,5-Dinitrobenzonitrile, 94% (GC) 1930-72-9
(n-Butyl)triphenylphosphonium bromide, 99% 1779-51-7
L-Tyrosine-D11 39748-77-1
Dimethyl pimelate, 99% 1732-08-7
Decahydronaphthalene-d18, 99.5 atom % D 91-17-8
4,4'-Dimethoxybiphenyl, 98% 2132-80-1
4-Bromo-N,N-Dimethylaniline, 99% 586-77-6
n-Benzylethanolamine, 96% (gc) 104-63-2
Dioctyl phenylphosphonate 98% 1754-47-8
4-Nitrobenzenesulfonyl chloride, 95% (titr.) 98-74-8
1,4-Diisopropylbenzene, 99% 100-18-5
4,4'-bis(pentyloxy)azoxybenzene 19482-05-4
Benzyl Cinnamate, 99% 103-41-3
4'-Methoxybutyrophenone, Tech., 93% (GC) 4160-51-4
2,2,5,5-Tetramethyl-3-Imidazoline-1-Oxyl-Carboxylic Acid, Sodium 0-00-0
2-Ethylaniline, 98% 578-54-1
1-Amino-4-methylpiperazine, 99% 6928-85-4
Squalane, 99% 111-01-3
Triphenylcarbenium hexachloroantimonate, 98% 1586-91-0
3-(Trifluoromethyl)-Cinnamic Acid, 98% 779-89-5
3-Pentyn-1-ol, 99% 10229-10-4
Rhodium Acetate Dimer, Anhydrous,ca 46% Rh 5503-41-3
Diethyl Carbonate, P.A. 105-58-8
Methyl 3-oxo-pentanoate, 98% 30414-53-0
Ethyl 3-hydroxybutyrate, 99% 5405-41-4
4-Propylaniline, 98% 2696-84-6
2'-Fluoro-4'-Methoxyacetophenone, 99% 74457-86-6
Lithiumtriethylborodeuteride, 1M solution in THF 109-99-9
2-Chlorobenzotrifluoride, 99% 88-16-4
1-Chloro-1-phenylethane, 99% 672-65-1

Free MSDS Search ( Providing 250,000+ Material Properties )
Chemcas.com| Ads link:todaystock.net