**** SECTION 2 - COMPOSITION, INFORMATION ON INGREDIENTS ****
+----------------+--------------------------------------+----------+-----------+
| CAS# | Chemical Name | % | EINECS# |
|----------------|--------------------------------------|----------|-----------|
| 9002-86-2 |Poly(vinyl chloride) | 100 | 206-625-7 |
+----------------+--------------------------------------+----------+-----------+
Hazard Symbols: None Listed.
Risk Phrases: None Listed.
**** SECTION 3 - HAZARDS IDENTIFICATION ****
EMERGENCY OVERVIEW
The toxicological properties of this material have not been fully
investigated.Cancer suspect agent.
Potential Health Effects
Eye:
May cause eye irritation.
Skin:
May cause skin irritation.
Ingestion:
May cause irritation of the digestive tract.
Inhalation:
May cause respiratory tract irritation.
Chronic:
Experimental carcinogen. Chronic inhalation of dust can cause
pulmonary damage, blood effects, and abnormal liver function.
**** SECTION 4 - FIRST AID MEASURES ****
Eyes:
Flush eyes with plenty of water for at least 15 minutes,
occasionally lifting the upper and lower eyelids. Get medical aid
immediately.
Skin:
Get medical aid. Flush skin with plenty of water for at least 15
minutes while removing contaminated clothing and shoes. Wash clothing
before reuse.
Ingestion:
If victim is conscious and alert, give 2-4 cupfuls of milk or water.
Never give anything by mouth to an unconscious person. Get medical
aid immediately.
Inhalation:
Remove from exposure and move to fresh air immediately. If not
breathing, give artificial respiration. If breathing is difficult,
give oxygen. Get medical aid.
Notes to Physician:
**** SECTION 5 - FIRE FIGHTING MEASURES ****
General Information:
As in any fire, wear a self-contained breathing apparatus in
pressure-demand, MSHA/NIOSH (approved or equivalent), and full
protective gear. During a fire, irritating and highly toxic gases
may be generated by thermal decomposition or combustion.
Extinguishing Media:
Use agent most appropriate to extinguish fire. Use water spray, dry
chemical, carbon dioxide, or appropriate foam.
**** SECTION 6 - ACCIDENTAL RELEASE MEASURES ****
General Information: Use proper personal protective equipment as indicated
in Section 8.
Spills/Leaks:
Clean up spills immediately, observing precautions in the Protective
Equipment section. Avoid generating dusty conditions. Provide
ventilation. Cover with dry earth, dry sand, or other non-combustible
material followed with plastic sheet to minimize spreading and
contact with water.
**** SECTION 7 - HANDLING and STORAGE ****
Handling:
Wash thoroughly after handling. Remove contaminated clothing and
wash before reuse. Use with adequate ventilation. Minimize dust
generation and accumulation. Avoid contact with eyes, skin, and
clothing. Keep container tightly closed. Avoid ingestion and
inhalation.
Storage:
Keep away from heat and flame. Keep away from sources of ignition.
Store in a tightly closed container. Store in a cool, dry,
well-ventilated area away from incompatible substances. Store
protected from light.
**** SECTION 8 - EXPOSURE CONTROLS, PERSONAL PROTECTION ****
Engineering Controls:
Use adequate ventilation to keep airborne concentrations low.
Exposure Limits
CAS# 9002-86-2:
United Kingdom, WEL - TWA: 10 mg/m3 TWA (inhalable dust); 4 mg/m3
(respirable dust)
United Kingdom, WEL - STEL: 30 mg/m3 STEL (inhalable dust); 12 mg
STEL (respirable dust)
Japan: 1 mg/m3 OEL (respirable dust); 4 mg/m3 OEL (total dust)
Netherlands: 2.5 mg/m3 MAC (dust)
Russia: 6 mg/m3 TWA (inhalable dust)
Personal Protective Equipment
Eyes:
Wear appropriate protective eyeglasses or chemical
safety goggles as described by OSHA's eye and face
protection regulations in 29 CFR 1910.133 or European
Standard EN166.
Skin:
Wear appropriate protective gloves to prevent skin
exposure.
Clothing:
Wear appropriate protective clothing to prevent skin
exposure.
Respirators:
A respiratory protection program that meets OSHA's 29
CFR 1910.134 and ANSI Z88.2 requirements or European
Standard EN 149 must be followed whenever workplace
conditions warrant respirator use.
**** SECTION 9 - PHYSICAL AND CHEMICAL PROPERTIES ****
Physical State: Powder
Color: Off - White Powder
Odor: None reported.
pH: Not available.
Vapor Pressure: Not available.
Viscosity: Not available.
Boiling Point: Not available.
Freezing/Melting Point: Not available.
Autoignition Temperature: 435 deg C ( 815.00 deg F)
Flash Point: Not available.
Explosion Limits, lower: Not available.
Explosion Limits, upper: Not available.
Decomposition Temperature:
Solubility in water:
Specific Gravity/Density: 1.4000g/cm3
Molecular Formula:
Molecular Weight:
**** SECTION 10 - STABILITY AND REACTIVITY ****
Chemical Stability:
Reacts violently with F2. Ordinary temperatures cause slow
dehalogenation producing hydrogen chloride.
Conditions to Avoid:
Incompatible materials, light, dust generation, excess heat, strong
oxidants.
Incompatibilities with Other Materials:
Strong oxidizing agents.
Hazardous Decomposition Products:
Hydrogen chloride, phosgene, carbon monoxide, carbon dioxide.
Hazardous Polymerization: May occur.
**** SECTION 11 - TOXICOLOGICAL INFORMATION ****
RTECS#:
CAS# 9002-86-2: KV0350000
LD50/LC50:
Not available.
Carcinogenicity:
Poly(vinyl chloride) -
Not listed by ACGIH, IARC, or NTP.
Other:
See actual entry in RTECS for complete information.
**** SECTION 12 - ECOLOGICAL INFORMATION ****
**** SECTION 13 - DISPOSAL CONSIDERATIONS ****
Dispose of in a manner consistent with federal, state, and local regulations.
**** SECTION 14 - TRANSPORT INFORMATION ****
IATA
Not regulated as a hazardous material.
IMO
Not regulated as a hazardous material.
RID/ADR
Not regulated as a hazardous material.
**** SECTION 15 - REGULATORY INFORMATION ****
European/International Regulations
European Labeling in Accordance with EC Directives
Hazard Symbols: Not available.
Risk Phrases:
Safety Phrases:
S 24/25 Avoid contact with skin and eyes.
S 28A After contact with skin, wash immediately with
plenty of water.
S 37 Wear suitable gloves.
S 45 In case of accident or if you feel unwell, seek
medical advice immediately (show the label where
possible).
WGK (Water Danger/Protection)
CAS# 9002-86-2: 0
Canada
CAS# 9002-86-2 is listed on Canada's DSL List.
CAS# 9002-86-2 is not listed on Canada's Ingredient Disclosure List.
US FEDERAL
TSCA
CAS# 9002-86-2 is listed on the TSCA inventory.
**** SECTION 16 - ADDITIONAL INFORMATION ****
MSDS Creation Date: 12/01/1998 Revision #3 Date: 3/18/2003
The information above is believed to be accurate and represents the best
information currently available to us. However, we make no warranty of
merchantability or any other warranty, express or implied, with respect to
such information, and we assume no liability resulting from its use. Users
should make their own investigations to determine the suitability of the
information for their particular purposes. In no way shall the company be
liable for any claims, losses, or damages of any third party or for lost
profits or any special, indirect, incidental, consequential or exemplary
damages, howsoever arising, even if the company has been advised of
the possibility of such damages.
--------------------------------------------------------------------------------
--------------------------------------------------------------------------------
|
|
|
| ALL MSDS PAGES IN THIS GROUP
| | NAME | CAS |
|
2-Anilinoethanol, 98%
| 122-98-5 |
|
2,4-Dimethylstyrene
| 2234-20-0 |
|
5-Sulfoisophthalic acid,monosodium salt 98%
| 6362-79-4 |
|
1,3-Dichloro-2-Butene, 96%, Mixture of Cis and Trans Isomers
| 926-57-8 |
|
3,4-Difluorobenzonitrile, 97%
| 64248-62-0 |
|
3-Aminopyrazole-4-Carboxylic Acid, 95%
| 24447-68-5 |
|
N-Methyl-p-phenylenediamine dihydrochloride, 98% (titr.)
| 5395-70-0 |
|
9,10-Bis(Phenylethynyl)Anthracene
| 10075-85-1 |
|
2-(2-Benzoxazolyl)malondialdehyde
| 40071-07-6 |
|
Bicyclohexyl
| 92-51-3 |
|
9-Octyl-9-heptadecanol, tech.
| 17687-72-8 |
|
1-Naphthyl isocyanate, 99%
| 86-84-0 |
|
3-Cyanophenol, 97%
| 873-62-1 |
|
Trimethylacetamide, 98%
| 754-10-9 |
|
4-Acetoxybiphenyl, 99+%
| 148-86-7 |
|
Allyl Acetate, 99%
| 591-87-7 |
|
Ethyl Thiocyanate, 99% (GC)
| 542-90-5 |
|
3,5-Dichlorobenzoic Acid, 99%
| 51-36-5 |
|
Ethyl 2-aminocyclopenta[b]thiophene-3-carboxylate, 99+%
| 4815-29-6 |
|
4-Carboxybenzaldehyde 97%
| 619-66-9 |
|
N-Methylacetamide, 99+%
| 79-16-3 |
|
5-Nitro-2-furanacrolein, tech, 92%
| 1874-22-2 |
|
(2R,3R)-3-Phenyl Glycidol, 96% (GC)
| 98819-68-2 |
|
2-Bromopyridine, 99%
| 109-04-6 |
|
Citronellyl Acetate, 97%
| 150-84-5 |
|
4-Penten-1-ol, 99%
| 821-09-0 |
|
Alpha, Alpha-Dicyclopropylbenzene-Methanol
| 5689-19-0 |
|
Osmium(III) chloride, 63.2% to 65.2% Os
| 13444-93-4 |
|
Tetramethylammonium Fluoride Trihydrate, 99% (Titr.)
| 373-68-2 |
|
Cytochrome c, horse heart muscle 90% warburg activity
| 9007-43-6 |
|
Octylamine, 99+% (GC)
| 111-86-4 |
|
2,3-Diaminonaphthalene, 97%
| 771-97-1 |
|
1-(4-Bromophenyl)-2-Pyrrolidinone 99+%(GC)
| 7661-32-7 |
|
4-Aminobutyric acid, 99+%
| 56-12-2 |
|
2'-Methylacetoacetanilide, 99% (HPLC)
| 93-68-5 |
|
4-Cyclohexyl-1-Butanol, 99%
| 4441-57-0 |
|
Pipes (1,4-Piperazinebis(Ethanesulfonic Acid)) 98.5+%
| 5625-37-6 |
|
5-Norbornene-2-acrylic acid, 99%
| 15222-64-7 |
|
4-Amino-2,6-Dimethylpyrimidine, 99%
| 461-98-3 |
|
N-Methyloctylamine, 95% (GC)
| 2439-54-5 |
|
Poly(2-ethylhexyl acrylate), 32% solids solution in Toluene, average
| 108-88-3 |
|
N-Ethylethylenediamine, 98+%
| 110-72-5 |
|
4,6-Dihydroxy-2-Mercaptopyrimidine, 98%
| 504-17-6 |
|
Poly T(R)-128
| 68550-83-4 |
|
Cyclopropylphenylmethane, 99%
| 1667-00-1 |
|
2-Methylindoline, 99+%
| 6872-06-6 |
|
4-Biphenylmethanol 98%
| 3597-91-9 |
|
2-Bromofluorene, 95%
| 1133-80-8 |
|
2-Norbornaneacetic Acid, 96%
| 1007-01-8 |
|
Poly(vinyl chloride), high molecular weight
| 9002-86-2 |
|
|