===================== Product Identification =====================
MSDS NAME:C-100 A/C-101 A
NIIN:00N017635
MSDS Number: BLTBN
=== Responsible Party ===
Company:CARPENTER INSULATION & COATINGS CO
Address:5016 MONUMENT AVE
City:RICHMOND
State:VA
ZIP:23261
Country:US
Info Phone Num:804-233-8391
Emergency Phone Num:800-424-9300 CHEMTREC
CAGE:90479
=== Contractor Identification ===
Company:CARPENTER INSULATION & COATINGS CO
Address:5016 MONUMENT AVE
Box:City:RICHMOND
State:VA
ZIP:23261
Country:US
Phone:804-233-8391
CAGE:90479
============= Composition/Information on Ingredients =============
Name:STRUCTURALLY SIMILAR OLIGOMERS
Name:ISOCYANIC ACID, METHYLENEDI-P-PHENYLENE ESTER;(METHYLENE
BIS (PHENYLISOCYANATE)), (MDI)
CAS:101-68-8
RTECS #:NQ9350000
Fraction by Wt: 50%
OSHA PEL:0.02 PPM,C (MFR)
ACGIH TLV:0.005 PPM (MFR)
EPA Rpt Qty:1 LB
DOT Rpt Qty:1 LB
===================== Hazards Identification =====================
LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES Skin:YES Ingestion:NO
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:ACUTE: LOW ORDER OF ACUTE TOXICITY BUT
MATERIAL CAN IRRITATE MUC MEMB OF MOUTH AND THROAT. INHAL: CAN
INDUCE ASTHMA-LIKE RESPIRATORY SENSITIZATION REACTION. EYE: MAY
CAUSE MILD TO MODERATE IRRITATION. SKIN: REPEATED CONT CAN CAUSE
SKIN SENSITIZATION. CHRONIC: CONTINUED OVEREXPOSURE MAY LEAD TO
(EFTS OF OVEREXP)
Explanation of Carcinogenicity:NOT RELEVANT.
Effects of Overexposure:HLTH HAZ: SENSITIZATION REACTION RESULTING IN
ASTHMA-LIKE REACTION UPON EXPOSURE BELOW TLV. SYMP OF OVEREXP TO
VAPORS OR MISTS MAY INITIALLY IMPAIR RESPIRATORY SYSTEM AND CAUSE
EYE IRRITATION.
Medical Cond Aggravated by Exposure:PERSONS WITH RESPIRATORY PROBLEMS
OR ASTHMA SHOULD NOT USE THIS PRODUCT.
======================= First Aid Measures =======================
First Aid:INGEST: DO NOT INDUCE VOMIT. IF CONSCIOUS, GIVE 2 GLASSES OF
WATER TO DRINK. CONSULT MED PERS. INHAL: REMOVE TO FRESH AIR.
ASSIST BRTHG AND CONTACT PHYS AS REQUIRED. SKIN: WASH THOROUGHLY
WITH SOAP AN D WATER. IF REDNESS DEVELOPS, CONTACT PHYS. EYE: IMMED
FLUSH EYES WITH FLOWING WATER FOR AT LEAST 15 MIN. CONTACT PHYS.
===================== Fire Fighting Measures =====================
Flash Point Method:COC
Flash Point:>400F,>204C
Extinguishing Media:DRY CHEMICAL, FOAM, CO*2, HALON 1211.
Fire Fighting Procedures:WEAR NIOSH/MSHA APPROVED SCBA & FULL
PROTECTIVE EQUIPMENT .
Unusual Fire/Explosion Hazard:MATERIAL REACTS WITH WATER. DO NOT RESEAL
WATER CONTAMD CONTAINERS DUE TO POSSIBLE PRESSURE BUILD-UP WITH
TIME.
================== Accidental Release Measures ==================
Spill Release Procedures:EVACUATE AREA. RESPONDING EMER PERS MUST HAVE
POS PRESS RESP EQUIP. STOP LEAK. DAM UP ANY LIQ; ABSORB & PLACE IN
OPEN CONTR. TRANSPORT OUTDOORS/TREAT W/DECONTAMINANT(5%
DETERGENT/5% AMMONIUM HYDROXIDE IN H*2O). TREAT SPILL AREA ADDNL
W/DECONTAMINANT.
Neutralizing Agent:SEE SPILL PROCEDURE.
====================== Handling and Storage ======================
Handling and Storage Precautions:STORE IN COOL DRY LOCATION. KEEP
CONTAINER TIGHTLY CLOSED. AVOID BREATHING VAPORS. OPEN CONTAINERS
SLOWLY TO RELIEVE ANY PRESSURE BUILD-UP.
============= Exposure Controls/Personal Protection =============
Respiratory Protection:USE NIOSH/MSHA APPROVED POSITIVE PRESSURE
SUPPLIED AIR RESPIRATOR IF CONCENTRATION EXCEEDS TLV.
Ventilation:LOCAL.
Protective Gloves:BUTYL OR NITRILE RUBBER GLOVES.
Eye Protection:CHEMICAL WORKERS GOGGLES .
Other Protective Equipment:CHEMICAL APRON AND ARM COVERS. EYEWASH
STATION AND SAFETY SHOWER SHOULD BE NEAR.
Work Hygienic Practices:WASH THOROUGHLY AFTER USING.
Supplemental Safety and Health
MATLS TO AVOID: & IS ACCELERATED BY ALKALIES, AMINES, AND SOME METAL
COMPOUNDS.
================== Physical/Chemical Properties ==================
Boiling Pt:B.P. Text:646(DECOMP)
Vapor Pres:<0.0001
Vapor Density:8.6
Spec Gravity:1.23
Evaporation Rate & Reference:<1(BUTACE=1)
Solubility in Water:REACTS
Appearance and Odor:VISCOUS DARK BROWN LIQUID, SLIGHT AROMATIC ODOR.
================= Stability and Reactivity Data =================
Stability Indicator/Materials to Avoid:YES
REACTS W/MATL, HAVING ACTIVE HYDROGENS SUCH AS H*2O, ALCOHOL, AMMONIA,
AMINES, ALKALIES. H*2O RXN CAN BE VIOLENT(SUPDAT)
Stability Condition to Avoid:TEMPERATURES GREATER THAN 180F.
Hazardous Decomposition Products:UPON BURNING, OXIDES OF CARBON AND
NITROGEN, TRACES OF HYDROGEN CYANIDE.
Conditions to Avoid Polymerization:HIGH TEMPERATURES; PRESENT OF
ALKALIE, AMINES, AND METAL COMPOUNDS.
==================== Disposal Considerations ====================
Waste Disposal Methods:DISPOSE OF MATERIALS IN ACCORDANCE WITH FEDERAL,
STATE, AND LOCAL REGULATIONS.
Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.
*** END OF RECORD *** |
|
|
| ALL PAGES On Chemical Property IN THIS GROUP
| | NAME | CAS |
|
HETRON FR 991, 566639
| 100-42-5 |
|
UGL 222 LITE SPACKLE 244
| 107-21-2
65997-17-3
9003-20-7
7732-18-5 |
|
C-100 A/C-101 A
| 101-68-8 |
|
RUSTLICK 711
| |
|
50-082, BREAKTHRU SAT-SAFTY BLU 50 82
| 111-76-2
84-74-2 |
|
CROWN VM&P NAPHTHA RULE 66/LIGHT ALIPHATIC(
| 8030-30-6
108-88-3
1330-20-7 |
|
ASPHALT EMULSION SS-1H, CPS291126
| 8052-42-4
7732-18-5 |
|
DECANE
| 124-18-5 |
|
LUSTER-GUARD, 4093.
| |
|
MITT GARD AA, 5946
| |
|
CGL 1320 RESIN
| 2425-79-8
7429-90-5
7782-42-5
21645-51-2
28768-32-3
1302-78-9
1333-86-4 |
|
ETHANOX 702 ANTIOXIDANT
| 118-82-1 |
|
INDUSTRIAL EPOXY, 101-147A & B RED PRIMER
| 13530-65-9
111-46-6
1330-20-7 |
|
EPOXY PRIMER COMPONENT B, 101-147B
| 1330-20-7 |
|
INDUSTRIAL EPOXY, 101-155 PRIMER
| 13530-65-9
108-10-1
1330-20-7
108-88-3 |
|
EPOXY PRIMER COMPONENT B, 101-155B
| 1330-20-7 |
|
INDUSTRIAL ACRYLIC EPOXY, 138-34 A&B
| 110-80-5
121-44-8
7732-18-5 |
|
INDUSTRIAL ENAMEL, 139-1 WHITE
| |
|
INDUSTRIAL ENAMEL, 139-2 BLACK
| |
|
INDUSTRIAL ENAMEL CLEAR BASE, 139-36
| |
|
INDUSTRIAL ENAMEL DEEP BASE, 139-38
| |
|
INDUSTRIAL ENAMEL, 139-101 WHITE
| |
|
INDUSTRIAL ENAMEL, 139-134 INTERNATIONAL RE
| |
|
INDUSTRIAL ENAMEL, 139-136 OSHA RED
| |
|
INDUSTRIAL ENAMEL, 139-137/139-1030 BLUE
| |
|
VITRALON QD ENAMEL RTV, 865-261
| 8030-30-6
64742-89-8
13463-67-7
1330-20-7
100-41-4 |
|
SN 150, 482200
| 64741-88-4 |
|
CUSTOM STANDARD SOLUTION SINGLE ELEMENT
| 7664-93-9
77-92-9 |
|
SEQUESTRENE AA-92
| 139-13-9
60-00-4 |
|
QZ 3289 ADHESION CONCENTRATE
| 64-17-5 |
|
CGL 1330
| 931-36-2
25085-99-8
28064-14-4
68738-77-2 |
|
RP 1510 HARDENER
| 1477-55-0
616-47-7
2855-13-2
68738-77-2 |
|
ARALDITE RD-2
| 2425-79-8 |
|
ARALDITE PY 307
| 28064-14-4 |
|
ARALDITE RD-1
| 2426-08-6 |
|
ARALDITE GY 507
| 26447-14-3
25068-38-6 |
|
HARDENER HY 837
| 108-95-2 |
|
ARALDITE GY 506
| 2426-08-6
25068-38-6 |
|
5090/DOCUTECH DRY INK, 6R272 (FX)
| 9003-55-8
1309-37-1
1333-86-4
3843-16-1 |
|
5090/DOCUTECH DRY INK, 6R90100 (RX)
| 9003-55-8
1309-37-1
1333-86-4
3843-16-1 |
|
5090/DOCUTECH DRY INK, 6R516 (XCI)
| 9003-55-8
1309-37-1
1333-86-4
3843-16-1 |
|
POWER BELT TREATMENT # 91004
| 71-55-6 |
|
POWER BELT TREATMENT # 91001
| 68476-86-8
71-55-6 |
|
ANFO P
| 6484-52-2 |
|
SCREEN CLEANER
| 64-17-5
7732-18-5 |
|
BUN REAGENT X315XX
| 26628-22-8 |
|
500 SUPER SEAL PVA SEALER, B500
| 14808-60-7
107-21-1 |
|
330 SUNSHIELD EXTERIOR SG:TB; B330
| 57-55-6
25265-77-4 |
|
220 INTERIOR SEMIGLOSS:TB, B220
| 57-55-6
25265-77-4 |
|
221 INTERIOR SEMI-GLOSS:XX, 0221
| 25265-77-4
57-55-6 |
|
|