===================== Product Identification =====================
MSDS NAME:330 SUNSHIELD EXTERIOR SG:TB; B330
NIIN:00N017838
MSDS Number: BLTDV
=== Responsible Party ===
Company:DAVLIN PAINT COMPANY
Box:2308
City:BERKELEY
State:CA
ZIP:94702
Country:US
Info Phone Num:415-848-2863
Emergency Phone Num:415-889-7098
Preparer's Name:PATRICIA SHAW
CAGE:HO931
=== Contractor Identification ===
Company:DAVLIN PAINT CO INC
Address:700 ALLSTON WAY
Box:2308
City:BERKELEY
State:CA
ZIP:94702
Country:US
Phone:510-848-2863
CAGE:3Z268
Company:DAVLIN PAINT COMPANY
Box:2308
City:BERKELEY
State:CA
ZIP:94702
Country:US
Phone:415-848-2863
CAGE:HO931
============= Composition/Information on Ingredients =============
Name:1,2 PROPANEDIOL; (PROPYLENE GLYCOL). VP:0.2 @ 68F.
CAS:57-55-6
RTECS #:TY2000000
Fraction by Wt: 5%
Name:PROPIONIC ACID, 2-METHYL-, MONOESTER
W/2,2,4-TRIMETHYL-1,3-PENTANEDIOL. VP:1.0 @ 189F.
CAS:25265-77-4
RTECS #:UF6000000
Fraction by Wt: <5.0%
===================== Hazards Identification =====================
LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES Skin:NO Ingestion:YES
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:INHAL:EXCESSIVE EXPOS TO VAPS OR SPRAY
MISTS CAN CAUSE IRRIT OF EYES, NOSE & THROAT. SKIN:MAY CAUSE SKIN
IRRIT OR RASH UPON PROLONGED OR REPEATED CONTACT. CONTACT MAY
RESULT IN SKIN ABSORPTION, BY SYM PTOMS OF TOX ARE NOT ANTICIPATED.
EYE:MAY BE AN IRRIT. INGEST:CAN CAUSE GI IRRIT, VOMIT, NAUS, OR
DIAR.(EFTS OF OVEREXP)
Explanation of Carcinogenicity:NOT RELEVANT.
Effects of Overexposure:HLTH HAZ:CHRONIC OVEREXPOSURE TO THIS MATERIAL
MAY LEAD TO SKIN DRYING, RASHES. OVEREXPOSURE TO ITS VAPORS, AS
WHEN IT IS HEATED OR SPRAYED, WILL LEAD TO IRRITATION OF NOSE,
THROAT, AND LUNGS.
Medical Cond Aggravated by Exposure:DERMATITIS, RESPIRATORY TRACT
IRRITATION.
======================= First Aid Measures =======================
First Aid:INHAL:REMOVE TO FRESH AIR. IF SYMPTOMS PERSIST, CALL MD.
EYE:FLUSH WITH LARGE QUANTITIES OF WATER FOR AT LEAST 15 MINUTES
AND CALL MD. SKIN:WASH THOROUGHLY WITH SOAP AND WATER. INGEST:DRINK
1 OR 2 GLA SSES OF WATER TO DILUTE. DO NOT INDUCE VOMITING. CALL MD
OR POISON CONTROL CENTER IMMEDIATELY. TREAT SYMPTOMATICALLY.
===================== Fire Fighting Measures =====================
Flash Point Method:TCC
Flash Point:241F,116C
Lower Limits:0.6%
Upper Limits:12.5%
Extinguishing Media:ALCOHOL FOAM, CO*2, DRY CHEMICAL.
Fire Fighting Procedures:WEAR NIOSH/MSHA APPROVED SCBA AND FULL
PROTECTIVE EQUIPMENT .
Unusual Fire/Explosion Hazard:ALTHOUGH MATERIAL IS NON-FLAMM, VAPS CAN
COLLECT ABOVE LIQ IN CLSD CNTNRS & STOR VESSELS WHICH MAY FLASH IF
EXPOSED TO IGNIT SOURCE. CLSD CNTNRS MAY (SUPP DATA)
================== Accidental Release Measures ==================
Spill Release Procedures:KEEP SPECTATORS AWAY. FLOOR MAY BE SLIPPERY,
USE CARE TO AVOID FALLING. DIKE AND CONTAIN SPILL WITH INERT
MATERIAL. TRANSFER LIQUID AND DIKING MATERIAL TO CONTAINERS FOR
RECOVERY AND DISPOSAL. KEEP SP ILLS OUT OF SEWERS AND OPEN WATER.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.
====================== Handling and Storage ======================
Handling and Storage Precautions:DO NOT STORE ABOVE 100F. KEEP FROM
FREEZING.
Other Precautions:DO NOT TAKE INTERNALLY. KEEP CONTAINERS CLOSED WHEN
NOT IN USE.
============= Exposure Controls/Personal Protection =============
Respiratory Protection:USE NIOSH/MSHA APPROVED EQUIPMENT WHEN AIRBORNE
EXPOSURE LIMITS ARE EXCEEDED. CONSULT RESP MANUFACTURER TO
DETERMINE APPROPRIATE EQUIP FOR GIVEN APPLICATIONS. HIGH AIRBORNE
CONCENTRATIONS MAY REQUIRE USE OF SUPPLIED-AIR RESIRATOR OR SCBA.
Ventilation:PROVIDE SUFFICIENT VENTILATION TO CONTROL EXPOSURE LEVELS
BELOW AIRBORNE EXPOSURE LIMITS.
Protective Gloves:IMPERVIOUS GLOVES .
Eye Protection:CHEMICAL WORKERS GOGGLES .
Other Protective Equipment:PROTECTIVE CLOTHING.
Work Hygienic Practices:WASH HANDS AFTER USING. REMOVE WET PAINT FROM
SKIN WITH WATER BEFORE IT DRIES.
Supplemental Safety and Health
EXPLO HAZ:EXPLODE WHEN EXPOSED TO EXTREME HEAT. MATERIAL CAN SPATTER
ABOVE 100C/212F. DRIED MATERIAL CAN BURN.
================== Physical/Chemical Properties ==================
HCC:N1
Boiling Pt:B.P. Text:212F,100C
Vapor Pres:SEE INGRED
Vapor Density:LTR/AIR
Spec Gravity:1.2
Evaporation Rate & Reference:SLOWER THAN ETHER
Solubility in Water:DILUTABLE
Appearance and Odor:PIGMENTED LIQUID
================= Stability and Reactivity Data =================
Stability Indicator/Materials to Avoid:YES
Hazardous Decomposition Products:UNDER SEVERE THERMAL DEGRADATION, LOW
MOLECULAR WEIGHT HYDROCARBONS MAY BE FORMED.
==================== Disposal Considerations ====================
Waste Disposal Methods:KEEP OUT OF DRAINS, SEWERS, AND WATERWAYS. LAND
FILL OR INCINERATE ACCORDING TO LOCAL, STATE AND FEDERAL
REGULATIONS.
Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.
*** END OF RECORD *** |
|
|
| ALL PAGES On Chemical Property IN THIS GROUP
| | NAME | CAS |
|
HETRON FR 991, 566639
| 100-42-5 |
|
UGL 222 LITE SPACKLE 244
| 107-21-2
65997-17-3
9003-20-7
7732-18-5 |
|
C-100 A/C-101 A
| 101-68-8 |
|
RUSTLICK 711
| |
|
50-082, BREAKTHRU SAT-SAFTY BLU 50 82
| 111-76-2
84-74-2 |
|
CROWN VM&P NAPHTHA RULE 66/LIGHT ALIPHATIC(
| 8030-30-6
108-88-3
1330-20-7 |
|
ASPHALT EMULSION SS-1H, CPS291126
| 8052-42-4
7732-18-5 |
|
DECANE
| 124-18-5 |
|
LUSTER-GUARD, 4093.
| |
|
MITT GARD AA, 5946
| |
|
CGL 1320 RESIN
| 2425-79-8
7429-90-5
7782-42-5
21645-51-2
28768-32-3
1302-78-9
1333-86-4 |
|
ETHANOX 702 ANTIOXIDANT
| 118-82-1 |
|
INDUSTRIAL EPOXY, 101-147A & B RED PRIMER
| 13530-65-9
111-46-6
1330-20-7 |
|
EPOXY PRIMER COMPONENT B, 101-147B
| 1330-20-7 |
|
INDUSTRIAL EPOXY, 101-155 PRIMER
| 13530-65-9
108-10-1
1330-20-7
108-88-3 |
|
EPOXY PRIMER COMPONENT B, 101-155B
| 1330-20-7 |
|
INDUSTRIAL ACRYLIC EPOXY, 138-34 A&B
| 110-80-5
121-44-8
7732-18-5 |
|
INDUSTRIAL ENAMEL, 139-1 WHITE
| |
|
INDUSTRIAL ENAMEL, 139-2 BLACK
| |
|
INDUSTRIAL ENAMEL CLEAR BASE, 139-36
| |
|
INDUSTRIAL ENAMEL DEEP BASE, 139-38
| |
|
INDUSTRIAL ENAMEL, 139-101 WHITE
| |
|
INDUSTRIAL ENAMEL, 139-134 INTERNATIONAL RE
| |
|
INDUSTRIAL ENAMEL, 139-136 OSHA RED
| |
|
INDUSTRIAL ENAMEL, 139-137/139-1030 BLUE
| |
|
VITRALON QD ENAMEL RTV, 865-261
| 8030-30-6
64742-89-8
13463-67-7
1330-20-7
100-41-4 |
|
SN 150, 482200
| 64741-88-4 |
|
CUSTOM STANDARD SOLUTION SINGLE ELEMENT
| 7664-93-9
77-92-9 |
|
SEQUESTRENE AA-92
| 139-13-9
60-00-4 |
|
QZ 3289 ADHESION CONCENTRATE
| 64-17-5 |
|
CGL 1330
| 931-36-2
25085-99-8
28064-14-4
68738-77-2 |
|
RP 1510 HARDENER
| 1477-55-0
616-47-7
2855-13-2
68738-77-2 |
|
ARALDITE RD-2
| 2425-79-8 |
|
ARALDITE PY 307
| 28064-14-4 |
|
ARALDITE RD-1
| 2426-08-6 |
|
ARALDITE GY 507
| 26447-14-3
25068-38-6 |
|
HARDENER HY 837
| 108-95-2 |
|
ARALDITE GY 506
| 2426-08-6
25068-38-6 |
|
5090/DOCUTECH DRY INK, 6R272 (FX)
| 9003-55-8
1309-37-1
1333-86-4
3843-16-1 |
|
5090/DOCUTECH DRY INK, 6R90100 (RX)
| 9003-55-8
1309-37-1
1333-86-4
3843-16-1 |
|
5090/DOCUTECH DRY INK, 6R516 (XCI)
| 9003-55-8
1309-37-1
1333-86-4
3843-16-1 |
|
POWER BELT TREATMENT # 91004
| 71-55-6 |
|
POWER BELT TREATMENT # 91001
| 68476-86-8
71-55-6 |
|
ANFO P
| 6484-52-2 |
|
SCREEN CLEANER
| 64-17-5
7732-18-5 |
|
BUN REAGENT X315XX
| 26628-22-8 |
|
500 SUPER SEAL PVA SEALER, B500
| 14808-60-7
107-21-1 |
|
330 SUNSHIELD EXTERIOR SG:TB; B330
| 57-55-6
25265-77-4 |
|
220 INTERIOR SEMIGLOSS:TB, B220
| 57-55-6
25265-77-4 |
|
221 INTERIOR SEMI-GLOSS:XX, 0221
| 25265-77-4
57-55-6 |
|
|