=====================  Product Identification  =====================

MSDS NAME:18 PATTERN & MODEL FILLER
NIIN:00N070377
MSDS Number: CBLRQ
=== Responsible Party ===
Company:ADTECH PLASTIC SYSTEMS CORP
Address:815 SHEPHERD ST
City:CHARLOTTE
State:MI
ZIP:48813
Country:US
Info Phone Num:800-255-9934
Emergency Phone Num:800-255-9934
CAGE:JO328
=== Contractor Identification ===
Company:AD-TECH PLASTIC SYSTEMS
Address:815 SHEPHERD STREET
Box:City:CHARLOTTE
State:MI
ZIP:48813
Phone:517-543-7510
CAGE:66058
Company:ADTECH PLASTIC SYSTEMS CORP
Address:815 SHEPHERD ST
Box:City:CHARLOTTE
State:MI
ZIP:48813
Country:US
Phone:800-255-9934
CAGE:JO328

=============  Composition/Information on Ingredients  =============

Name:UNSATURATED POLYESTER RESIN
Fraction by Wt: >35%
OSHA PEL:N/K 
ACGIH TLV:N/K 

Name:STYRENE; (STYRENE MONOMER) (SARA 313). LD50:(ORAL,RAT)
    5GM/KG
CAS:100-42-5
RTECS #:WL3675000
Fraction by Wt: <20%
OSHA PEL:100 PPM
ACGIH TLV:S, 50 PPM/100 STEL
EPA Rpt Qty:1000 LBS
DOT Rpt Qty:1000 LBS

Name:BARIUM SULFATE
CAS:7727-43-7
RTECS #:CR0600000
Fraction by Wt: <10%
OSHA PEL:15 MG/M3 TDUST
ACGIH TLV:10 MG/M3 TDUST

Name:TALC (POWDER), CONTAINING NO ASBESTOS FIBERS; (MAGNESIUM
    SILICATE)
CAS:14807-96-6
RTECS #:MW2700000
Fraction by Wt: <45%
OSHA PEL:0.2 FIBERS/CC
ACGIH TLV:0.2 FIBER/CC, A1

Name:TITANIUM OXIDE; (TITANIUM DIOXIDE)
CAS:13463-67-7
RTECS #:XR2275000
Fraction by Wt: <2%
OSHA PEL:15 MG/M3 TDUST
ACGIH TLV:10 MG/M3 TDUST

=====================  Hazards Identification  =====================

LD50 LC50 Mixture:SEE INGREDIENT 2
Routes of Entry: Inhalation:YES  Skin:YES  Ingestion:YES
Reports of Carcinogenicity:NTP:NO    IARC:YES	 OSHA:NO
Health Hazards Acute and Chronic:ACUTE:VAPORS CAN CAUSE IRRITATION OF
    EYES, NOSE AND THROAT IF USED ON CONFINED AREA. POSSIBLE
    OBJECTIONABLE ODOR. SIGNS AND SYMPTOMS OF EXPOSURE:REDNESS AND/OR
    SWELLING OF AFFECTED AREAS. CHRONIC:NONE  LISTED BY MANUFACTURER.
Explanation of Carcinogenicity:STYRENE:IARC MONO, SUPP, VOL 7, PG 345,
    1987:GROUP 2B. ANIMAL:NERV SYS.
Effects of Overexposure:SEE HEALTH HAZARDS.
Medical Cond Aggravated by Exposure:NOT KNOWN.

=======================  First Aid Measures  =======================

Eyes:FLUSH WITH WATER FOR @ LEAST 15 MINUTES, CONTACT
    PHYSICIAN. SKIN:WASH WITH MILD SOAP AND WATER. INHAL:REMOVE FROM
    CONTAMINATION TO FRESH AIR. INGEST:DO NOT INDUCE VOMITING, CONTACT
    PHYSICIAN.

=====================  Fire Fighting Measures  =====================

Flash Point Method:SCC
Flash Point:92.0F,33.3C
Extinguishing Media:WATER FOG, DRY CHEMICAL, ALCOHOL FOAM, CO*2.
Fire Fighting Procedures:NONE. USE NIOSH/MSHA APPROVED SCBA & FULL
    PROTECTIVE EQUIPMENT .
Unusual Fire/Explosion Hazard:STYRENE WILL POLYMERIZE READILY AT
    ELEVATED TEMPERATURES OF FIRE CONDITIONS. IF THIS OCCURS IN A
    CLOSED CONTAINER THERE IS POSSIBILITY OF A RUPTURE.

==================  Accidental Release Measures  ==================

Spill Release Procedures:SOAK UP WITH INERT MATERIAL AND PLACE IN
    CLOSED CONTAINERS. SCRAPE UP AND PLACE IN CONTAINER.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

======================	Handling and Storage  ======================

Handling and Storage Precautions:STORE AT AMBIENT TEMPERATURE IN A WELL
    VENTILATED AREA AWAY FROM EXCESSIVE HEAT OR OPEN FLAME.
Other Precautions:AVOID USING IN NON-VENTILATED/CONFINED AREAS FOR
    PROLONGED PERIODS TIME.

=============  Exposure Controls/Personal Protection  =============

Respiratory Protection:ONLY IF TLV IS EXCEEDED, NIOSH/MSHA APPROVED
    ORGANIC VAPOR TYPE.
Ventilation:LOCAL EXHAUST:RECOMMENDED. MECHANICAL (GENERAL):USUALLY IS
    ADEQUATE.
Protective Gloves:POLYETHYLENE OR RUBBER GLOVES.
Eye Protection:ANSI APPRVD CHEM WORKERS GOGGLES .
Other Protective Equipment:ANSI APPRVD EMERGENCY EYE WASH & DELUGE
    SHOWER .
Work Hygienic Practices:PRACTICE GOOD HYGIENE AND USE WITH CAUTION TO
    AVOID EYE OR SKIN CONTACT.
Supplemental Safety and Health

==================  Physical/Chemical Properties  ==================

Spec Gravity:1.64 (H*2O=1)
Evaporation Rate & Reference:<1 (BUTYL ACETATE =1)
Solubility in Water:SLIGHT
Appearance and Odor:PIGMENTED PASTE WITH TYPICAL STYRENE ODOR.
Percent Volatiles by Volume:15-20

=================  Stability and Reactivity Data  =================

Stability Indicator/Materials to Avoid:YES
STRONG ACIDS, OXIDIZING AGENTS AND ORGANIC PEROXIDES.
Stability Condition to Avoid:MATERIAL WILL POLYMERIZE WITH OXIDIZING
    AGENTS, STRONG ACIDS.
Hazardous Decomposition Products:CARBON MONOXIDE, LOW MOLECULAR WEIGHT
    HYDROCARBONS.
Conditions to Avoid Polymerization:EXPOSURE TO EXTREME HEAT OR OPEN
    FLAME.

====================  Disposal Considerations  ====================

Waste Disposal Methods:CATALYZE AND DISPOSE AS SOLID WASTE (LANDFILL)
    OR BURN IN ADEQUATE INCINERATOR ACCORDING TO LOCAL, STATE AND
    FEDERAL REGULATIONS.

 Disclaimer (provided with this information by the compiling agencies):
 This information is formulated for use by elements of the Department
 of Defense.  The United States of America in no manner whatsoever,
 expressly or implied, warrants this information to be accurate and
 disclaims all liability for its use.  Any person utilizing this
 document should seek competent professional advice to verify and
 assume responsibility for the suitability of this information to their
 particular situation.

*** END OF RECORD ***