=====================  Product Identification  =====================

MSDS NAME:EPO TEK H70E-4, PART A
NIIN:00N018272
Kit Part:Y
MSDS Number: CFNNY
=== Responsible Party ===
Company:EPOXY TECHNOLOGY
Address:14 FORTUNE DR
City:BILLERICA
State:MA
ZIP:01821
Country:US
Info Phone Num:508-667-3805
Emergency Phone Num:508-667-3805
CAGE:33246
=== Contractor Identification ===
Company:EPOXY TECHNOLOGY
Address:14 FORTUNE DRIVE
Box:City:BILLERICA
State:MA
ZIP:01821
Country:US
Phone:978-667-3805
CAGE:33246

=============  Composition/Information on Ingredients  =============

Name:METHANOL (SARA 313) (CERCLA)
CAS:67-56-1
RTECS #:PC1400000
Fraction by Wt: <2%
OSHA PEL:200 PPM, S
ACGIH TLV:200PPM/250 STEL, S
EPA Rpt Qty:5000 LBS
DOT Rpt Qty:5000 LBS

Name:ALUMINUM OXIDE (2:3); (ALUMINUM OXIDE) (SARA 313)
CAS:1344-28-1
RTECS #:BD1200000
Fraction by Wt: 40%
OSHA PEL:15 MG/M3 TDUST
ACGIH TLV:10 MG/M3 TDUST

=====================  Hazards Identification  =====================

LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES  Skin:YES  Ingestion:YES
Reports of Carcinogenicity:NTP:NO    IARC:NO	OSHA:NO
Health Hazards Acute and Chronic:ACUTE: INGESTION: CONTAINS METHANOL -
    A FLAMMABLE AND TOXIC MATERIAL. INHALATION: HOT VAPORS CAN CAUSE
    HEADACHES, NAUSEA, DIZZINESS, AND RESPIRATORY IRRITATION. SKIN: CAN
    CAUSE IRRITATION. EYES: IRRIT ATING TO EYES. CAN CAUSE INJURY.
    CHRONIC: CAN CAUSE DERMATITIS AND SENSITIZATION.
Explanation of Carcinogenicity:NOT RELEVANT.
Effects of Overexposure:SEE HEALTH HAZARDS.
Medical Cond Aggravated by Exposure:NONE SPECIFIED BY MANUFACTURER.

=======================  First Aid Measures  =======================

Eyes: FLUSH WITH WATER FOR AT LEAST 15 MINUTES. GET MEDICAL
    ATTENTION IMMEDIATELY. SKIN: CLEAN WITH SOAP AND WATER. DO NOT USE
    SOLVENTS. REMOVE CONTAMINATED CLOTHING. INGESTION: GET MEDICAL
    ATTENTION  IMMEDIATELY. INHALATION: REMOVE EMPLOYEE TO FRESH AIR.
    IF DISCOMFORT PERSISTS, GET MEDICAL ATTENTION.

=====================  Fire Fighting Measures  =====================

Extinguishing Media:DRY CHEMICAL, FOAM, CARBON DIOXIDE.
Fire Fighting Procedures:WEAR NIOSH APPROVED SCBA & FULL PROTECTIVE
    EQUIPMENT . REMOVE ALL IGNITION SOURCES. USE A WATER SPRAY TO COOL
    FIRE-EXPOSED CONTAINERS.
Unusual Fire/Explosion Hazard:AVOID FUMES LIBERATED BY HEAT.

==================  Accidental Release Measures  ==================

Spill Release Procedures:ELIMINATE IGNITION SOURCES. USE EYE AND SKIN
    PROTECTION. PLACE LEAKING CONTAINERS IN A WELL-VENTILATED AREA.
    ABSORB SPILLAGE WITH INERT MATERIAL AND DISPOSE.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

======================	Handling and Storage  ======================

Handling and Storage Precautions:AVOID CONTACT WITH SKIN AND EYES.
    AVOID BREATHING VAPORS. KEEP CONTAINERS CLOSED WHEN NOT IN USE.
Other Precautions:NONE SPECIFIED BY MANUFACTURER.

=============  Exposure Controls/Personal Protection  =============

Respiratory Protection:WEAR A NIOSH APPROVED RESPIRATOR FOR ORGANIC
    VAPORS WHENEVER HIGH LEVEL EXPOSURE TO VAPORS OR MIST IS
    ANTICIPATED.
Ventilation:LOCAL EXHAUST RECOMMENDED FOR EXPOSURE CONTROL.
Protective Gloves:IMPERVIOUS GLOVES, NEOPRENE/EQUIVALENT.
Eye Protection:ANSI APPRVD CHEM WORKERS GOGGLES .
Other Protective Equipment:ANSI APPRVD EMER EYEWASH & DELUGE SHOWER . A
    COMBINATION OF BARRIER CREAM & GLOVES IS REC. IMPERVIOUS APRON.
Work Hygienic Practices:REMOVE ALL CONTAM CLTHG IMMED & WASH. WASH SKIN
    THORO W/SOAP & WATER AFTER HNDLG. SOLVS SHOULD NOT BE USED TO (SUP
    DAT)
Supplemental Safety and Health
HYGIENE PRACT: CLEAN SKIN BECAUSE OF INCREASED PENETRATION POTENTIAL -
    PROT SKIN OILS CAN BE DISSOLVED BY SOLVENTS.

==================  Physical/Chemical Properties  ==================

Vapor Density:>AIR
Spec Gravity:1.61
Evaporation Rate & Reference:< BUTYL ACETATE
Solubility in Water:LOW
Appearance and Odor:OPAQUE PASTE, MILD ODOR
Percent Volatiles by Volume:<2

=================  Stability and Reactivity Data  =================

Stability Indicator/Materials to Avoid:YES
STRONG OXIDIZING AND REDUCING AGENTS.
Stability Condition to Avoid:EXCESSIVE HEAT.
Hazardous Decomposition Products:FUMES PRODUCED WHEN HEATED TO
    DECOMPOSITION MAY INCLUDE CARBON MONOXIDE, AND CARBON DIOXIDE.

====================  Disposal Considerations  ====================

Waste Disposal Methods:INCINERATE OR USE HAZARDOUS WASTE TREATMENT
    PROCEDURES THAT ARE IN ACCORDANCE WITH FEDERAL, STATE AND LOCAL
    REGULATIONS.

 Disclaimer (provided with this information by the compiling agencies):
 This information is formulated for use by elements of the Department
 of Defense.  The United States of America in no manner whatsoever,
 expressly or implied, warrants this information to be accurate and
 disclaims all liability for its use.  Any person utilizing this
 document should seek competent professional advice to verify and
 assume responsibility for the suitability of this information to their
 particular situation.

*** END OF RECORD ***