=====================  Product Identification  =====================

MSDS NAME:EUTECTRODE 4, 428862-01
NIIN:00-056-3606
MSDS Number: CGDSG
=== Responsible Party ===
Company:EUTECTIC CORP
Address:1515 BROOK DR
City:DOWNERS GROVE
State:IL
ZIP:60515
Country:US
Info Phone Num:800-323-4845
Emergency Phone Num:800-323-4845
CAGE:72271
=== Contractor Identification ===
Company:EUTECTIC CORP
Address:9625-J SOUTHERN PINE BLVD
Box:City:CHARLOTTE
State:NC
ZIP:28273
Country:US
Phone:704-527-9800/ 800-221-1433
CAGE:72271
Company:EUTECTIC CORPORATION
Address:1515 BROOK DR
Box:City:DOWNERS GROVE
State:IL
ZIP:60515
Country:US
Phone:800-323-4845
CAGE:5N977

=============  Composition/Information on Ingredients  =============

Name:IRON
CAS:7439-89-6
RTECS #:NO4565500
OSHA PEL:15 MG/M3 (MFR)
ACGIH TLV:10 MG/M3 (MFR)

Name:POTASSIUM SILICATE
CAS:1312-76-1
OSHA PEL:N/K 
ACGIH TLV:N/K 

Name:CHROMIUM (SARA 313) (CERCLA)
CAS:7440-47-3
RTECS #:GB4200000
Fraction by Wt: 5-10%
OSHA PEL:1 MG/M3
ACGIH TLV:0.5 MG/M3
EPA Rpt Qty:1 LB
DOT Rpt Qty:1 LB

Name:MANGANESE (SARA 313)
CAS:7439-96-5
RTECS #:OO9275000
Fraction by Wt: 5-10%
OSHA PEL:5 MG/M3 DUST, C
ACGIH TLV:5 MG/M3 DUST

Name:TITANIUM OXIDE; (TITANIUM DIOXIDE)
CAS:13463-67-7
RTECS #:XR2275000
OSHA PEL:15 MG/M3 TDUST
ACGIH TLV:10 MG/M3 TDUST

Name:NICKEL (SARA 313) (CERCLA)
CAS:7440-02-0
RTECS #:QR5950000
Fraction by Wt: 1-5%
OSHA PEL:1 MG/M3
ACGIH TLV:1 MG/M3

Name:CALCIUM FLUORIDE (AS F)
CAS:7789-75-5
RTECS #:EW1760000
OSHA PEL:2.5 MG/M3 (F) (MFR)
ACGIH TLV:2.5 MG/M3 (F) (MFR)

Name:CELLULOSE (PAPER FIBER)
CAS:9004-34-6
RTECS #:FJ5691460
OSHA PEL:15 MG/M3 TDUST
ACGIH TLV:10 MG/M3

Name:FELDSPAR
CAS:68476-25-5
OSHA PEL:15 MG/M3 (MFR)
ACGIH TLV:10 MG/M3 (MFR)

Name:IRON OXIDE; (MAGNETITE)
CAS:1309-38-2
RTECS #:OM4800000
OSHA PEL:15 MG/M3 (FE) (MFR)
ACGIH TLV:10 MG/M3 (FE) (MFR)

Name:POTASSIUM TITANATE
CAS:12030-97-6
OSHA PEL:N/K 
ACGIH TLV:N/K 

Name:MOLYBDENUM
CAS:7439-98-7
RTECS #:QA4680000
OSHA PEL:10 PPM
ACGIH TLV:10 PPM

Name:SUPP DATA:DARK TO SEE WELD ZONE, THEN GO TO NEXT LIGHTER
    SHADE WHICH GIVES SUFFICIENT VIEW OF THE WELD ZONE.
RTECS #:9999999ZZ

Name:HAZ DECOMP PROD:CANNOT BE CLASSIFIED SIMPLY. COMPOSITION &
    QTY OF THESE ARE DEPENDENT UPON METAL BEING WELDED, (ING 15)
RTECS #:9999999ZZ

Name:ING 14:PROCESS, PROCS & ELECTRODES/OTHER CONSUMABLES USED.
    DURING WELDING, THERMAL SPRAYING & ALLIED PROCESSES, (ING 16)
RTECS #:9999999ZZ

Name:ING 15:FUME & GAS DECOMP PRODS GENERATED ARE DIFF IN
    PERCENT IN FORM FROM INGS LISTED. GASEOUS RXN PRODS MAY (ING 17)
RTECS #:9999999ZZ

Name:ING 16:INCL OZONE, CARBON MONOXIDE, CARBON DIOXIDE,
    NITROGEN OXIDES & CERTAIN INERT GASES USED AS SHIELDING (ING 18)
RTECS #:9999999ZZ

Name:ING 17:GASES. FOR MORE SPECIFIC INFORMATION REGARDING
    HAZARDOUS DECOMPOSTION PRODUCTS CONTACT NEHC .
RTECS #:9999999ZZ

Name:EFTS OF OVEREXP:SIDEROSIS (IRON DEPOSITS IN LUNG). METAL
    FUME FEVER:CAN BE CAUSED BY INHAL OF CERTAIN METALLIC (ING 20)
RTECS #:9999999ZZ

Name:ING 19:CMPDS DURING WELDING, HEATING, BRAZING,
    SOLDERING/CUTTING OPERATIONS. SYMPS ARE SIMILAR TO FLU-TYPE (ING
    21)
RTECS #:9999999ZZ

Name:ING 20:SICKNESS INCL CHILLS, FEVER, HEAD & MUSC ACHE,
    TIGHTNESS OF CHEST, DRYNESS OF NOSE & MOUTH, MUSCULAR (ING 22)
RTECS #:9999999ZZ

Name:ING 21:PAIN, NAUS & VOMIT. SYMPS USUALLY OCCUR W/IN SEVERAL
    HRS AFTER OVEREXP & MAY LAST 6-24 HRS. CONSULT MD (ING 23)
RTECS #:9999999ZZ

Name:ING 22:IMMEDIATELY IF ANY OF THESE SYMPTOMS DEVELOP AFTER
    WELDING OPERATION. FOR MORE SPECIFIC INFORMATION (ING 24)
RTECS #:9999999ZZ

Name:ING 23:REGARDING HEALTH HAZARDS OF INDIVIDUAL INGREDIENTS
    CONTACT NEHC .
RTECS #:9999999ZZ

Name:OTHER PREC:SPRAYING", PUBLISHED BY THE AMERICAN WELDING
    SOCIETY & OSHA PUBLICATION 2206 (29 CFR 1910) FOR MORE DETAILS.
RTECS #:9999999ZZ

=====================  Hazards Identification  =====================

LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES  Skin:YES  Ingestion:YES
Reports of Carcinogenicity:NTP:YES    IARC:YES	  OSHA:NO
Health Hazards Acute and Chronic:INHAL:FUMES CAN BE DANGEROUS TO YOUR
    HLTH & OVEREXP CAN CAUSE LUNG DMG &/OR OTHER ORG DMG. EYE/SKIN
    CONT:ARC RAYS & UV LIGHT CAN INJURE EYES & BURN SKIN. LIQS USED IN
    FLUXES & CHEM AIDS MAY CAUSE IRRI T/POSS CHEM BURNS. ELEC SHOCK CAN
    KILL.INGEST:DANGER! MAY BE HARMFUL/FATAL IF SWALLOWED. GEN WELDING
    (EFTS OF OVEREXP)
Explanation of Carcinogenicity:NICKEL:IARC MONOGRAPHS, VOL 49, PG 247,
    1990:GRP 2B. NTP 7TH ANNUAL RPT ON CARCINS, 1994:ANTIC TO BE
    CARCIN. (SUPP DATA)
Effects of Overexposure:HLTH HAZ:FUMES:FUMES, GASES & DUSTS CAN BE
    DANGEROUS TO YOUR HLTH. CERTAIN MED STUDIES HAVE SUGGESTED THAT
    LUNG DMG CAN RSLT FROM OVEREXP TO THESE FUMES. SHORT TERM OVEREXP
    MAY RSLT IN DIZZ, NAUS, DRY NESS/IRRIT OF NOSE, THROAT/EYES.
    EXCESSIVE OVEREXP MAY CAUSE BRONCH ASTHMA, LUNG FIBROSIS,
    PNEUMOCONIOSIS/ (ING 19)
Medical Cond Aggravated by Exposure:AGGRAVATION OF PREEXISTING
    RESPIRATORY OR ALLERGIC CONDITIONS MAY OCCUR IN SOME WORKERS.

=======================  First Aid Measures  =======================

First Aid:INHAL:MOVE VICTIM TO FRESH AIR SOURCE. CONTACT MD & ADVISE ON
    INGS LISTED. SKIN:THORO WASH HANDS/AFFECTED AREAS W/SOAP & WATER TO
    REMOVE ALL RESIDUE. IF RASH/BURN DEVELOPS, CONSULT MD. EYES:THORO
    FLUS H W/WATER FOR AT LEAST 15 MINUTES TO REMOVE ALL RESIDUE.
    OBTAIN PROMPT MED ADVICE FOR FLUXES & CHEMICAL AIDS. ADVISE MD OF
    INGS LISTED. INGEST:CALL MD &/OR LOCAL POIS CTL CTR. ADVISE OF INGS
    LISTED.

=====================  Fire Fighting Measures  =====================

Extinguishing Media:CO*2, DRY CHEMICAL FOAM TYPE.
Fire Fighting Procedures:USE NIOSH APPROVED SCBA & FULL PROTECTIVE
    EQUIPMENT . TOXIC FUMES MAY BE PRODUCED. SEE HAZARDOUS
    DECOMPOSITION PRODUCTS SECTION.
Unusual Fire/Explosion Hazard:GENRLY NONFLAMM:WELDING ARC, SPKS &
    FLAMES CAN IGNITE COMBUSTS & FLAMMS. SOME FLUXES & CHEM AIDS MAY
    GIVE OFF HYDROGEN CHLORIDE, PHOSGENE & CHLORINE (SUPP DATA)

==================  Accidental Release Measures  ==================

Spill Release Procedures:NONE SPECIFIED BY MANUFACTURER.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

======================	Handling and Storage  ======================

Handling and Storage Precautions:TRAIN WELDER TO KEEP HIS/HER FACE AWAY
    FROM FUME/DUST PLUME. USE ADEQUATE VENTILATION TO KEEP BELOW
    EXPOSURE LIMITS. HANDLE W/CARE.
Other Precautions:TRAIN WORKERS NOT TO TOUCH LIVE ELEC PARTS & TO
    INSULATE THEMSELVES FROM WORK & ELEC GROUND. PLEASE READ &
    UNDERSTAND PROD LBL INFO FOR PROPER PROCS & USE. SEE ANSI Z49.1,
    "SFTY IN WELDING & CUTTING",  & CHAPTER 11 OF "THERMAL (ING 25)

=============  Exposure Controls/Personal Protection  =============

Respiratory Protection:IF WORK STATION IS NOT PROPERLY VENTILATED TO
    EXHAUST ALL FUMES, VAPORS & DUSTS BELOW RECOMMENDED EXPOSURE
    LIMITS, USE A NIOSH APPROVED RESPIRATOR.
Ventilation:USE ENOUGH GENERAL VENT & LOCAL EXHAUST AT WORK SITE TO
    KEEP ALL FUMES & DUSTS FROM WORKER'S BREATHING ZONE & GEN AREA.
Protective Gloves:WELDER'S GLOVES.
Eye Protection:ANSI APPRVD CHEM WORKERS GOGGS &(SUPDAT)
Other Protective Equipment:ANSI APPRVD EYE WASH FOUNTAIN & DELUGE
    SHOWER . WEAR HAND, HEAD & BODY PROT; THIS MAY INCL ARM
    PROTECTORS,(SUPDAT)
Work Hygienic Practices:NONE SPECIFIED BY MANUFACTURER.
Supplemental Safety and Health
EXPLO HAZ:GASES. CANS UNDER PRESS & FLAMMS MAY EXPLODE. EXPLAN OF
    CARCIN:ANIMAL:LUNGS, NASAL CAVITIES. OTHER PROT EQUIP:APRONS, HATS
    AS WELL AS DARK, PROT CLTHG. EYE PROT:FULL LGTH FSHLD , W/APP ROP
    FILTER LENS. PROVIDE PROT SCREENS &FLASH GOGGS IF NEC, TO SHIELD
    OTHERS. AS RULE, START W/SHADE THAT IS TOO(ING 13)

==================  Physical/Chemical Properties  ==================

Appearance and Odor:NONE SPECIFIED BY MANUFACTURER.

=================  Stability and Reactivity Data  =================

Stability Indicator/Materials to Avoid:YES
NONE SPECIFIED BY MANUFACTURER.
Stability Condition to Avoid:NONE SPECIFIED BY MANUFACTURER.
Hazardous Decomposition Products:FUMES, GASES & DUSTS GIVEN OFF DURING
    HEATING, WELDING, BRAZING, SOLDERING, CUTTING/THERMAL SPRAY
    PROCESSES (ING 14)

====================  Disposal Considerations  ====================

Waste Disposal Methods:DISP OF WASTE MATL, POWDERS, GRINDING/FILTER
    RESIDUES IN AN ENVIRONMENTALLY SENSITIVE MANNER I/A/W FED, STATE &
    LOC REGS. USE APPROP MEASURES TO KEEP AIRBORNE DUST LEVELS CNTND
    I/A/W EXPOS LEVELS. SEE  GEN HAZ SUMMARY SECTION FOR SAFE HNDLG&
    STORAGE.

 Disclaimer (provided with this information by the compiling agencies):
 This information is formulated for use by elements of the Department
 of Defense.  The United States of America in no manner whatsoever,
 expressly or implied, warrants this information to be accurate and
 disclaims all liability for its use.  Any person utilizing this
 document should seek competent professional advice to verify and
 assume responsibility for the suitability of this information to their
 particular situation.

*** END OF RECORD ***