TM
MATERIAL SAFETY DATA SHEET
BONDAFLEX SIL 2300 PRIMER
SECTION 1 鈥? IDENTIFICATION OF THE SUBSTANCE AND OF THE COMPANY
PRODUCT NAME: BONDAFLEX SIL 2300 PRIMER
PRODUCT CODE: 2300
ADDRESS: May National Associates, Inc.
995 Towbin Avenue
Lakewood, New Jersey 08701
PHONE: (800) 691-0234
FAX: (973) 473-4222
EMERGENCY PHONE: (CHEMTREC) (800) 424-9300
International (CHEMTREC) (703) 527-3887
PREPARED BY: Bruce Lakatosh
REVISION DATE: 3/11/08 SUPERCEDES: 8/23/04
Generic Description: MIXTURE OF INORGANIC AND ORGANIC COMPOUNDS
Physical Form: LIQUID
Color: COLORLESS TO PALE YELLOW
Odor: SLIGHT ODOR
NFPA Profile: Health 2 Flammability 1 Instability/Reactivity 0
Note: NFPA = National Fire Protection Association
SECTION 2 鈥? OSHA HAZARDOUS COMPONENTS
CAS Number Wt % Component Name
107-51-7 > 60.0 Octamethyltrisiloxane
682-01-9 5.0 - 10.0 Tetrapropyl orthosilicate
18407-95-9 5.0 - 10.0 1-Methoxyisopropyl orthosilicate
5593-70-4 5.0 - 10.0 Tetrabutyl titanate
71-36-3 <1.0 n-Butyl alcohol
The above components are hazardous as defined in 29 CFR 1910.1200.
SECTION 3 鈥? EFFECTS OF OVEREXPOSURE
Acute Effects
Eye: Direct contact may cause severe irritation.
Skin: May cause moderate irritation.
Inhalation: Harmful if inhaled. Overexposure may cause serious illness. Vapor and/or mist irritating
to the respiratory tract. Vapor overexposure may cause drowsiness.
Oral: No significant effects expected from a single short-term exposure. Swallowing large
amounts may cause drowsiness.
Prolonged/Repeated Exposure Effects
Skin: Repeated or prolonged exposure may irritate seriously.
1 OF 9
TM
MATERIAL SAFETY DATA SHEET
BONDAFLEX SIL 2300 PRIMER
Inhalation: No known applicable information.
Oral: Repeated ingestion or swallowing large amounts may injure internally.
Signs and Symptoms of Overexposure
No known applicable information.
Medical Conditions Aggravated by Exposure
No known applicable information.
The above listed potential effects of overexposure are based on actual data, results of studies performed upon similar
compositions, component data and/or expert review of the product. Please refer to Section 11 for the detailed toxicology
information.
SECTION 4 鈥? FIRST AID MEASURES
Eye: Immediately flush with water for 15 minutes. Get medical attention.
Skin: Remove from skin and wash thoroughly with soap and water or waterless cleanser. Get
medical attention if irritation or other ill effects develop or persist.
Inhalation: Remove to fresh air. Get immediate medical attention.
Oral: Get medical attention.
Comments: Treat according to person's condition and specifics of exposure.
SECTION 5 鈥? FIRE-FIGHTING MEASURES
Flash Point: 87.4 掳 / 30.8 掳 (Pensky-Martens Closed Cup)
F C
Autoignition
Temperature: Not determined.
Flammability Limits in Air: Not determined.
Extinguishing Media: On large fires use medium expansion (>30:1) AFFF alcohol compatible foam or water
spray. On small fires use medium expansion (>30:1) AFFF alcohol compatible foam,
CO2 or water spray. Water can be used to cool fire exposed containers.
Fire Fighting Measures: Self-contained breathing apparatus and protective clothing should be worn in fighting
large fires involving chemicals. Determine the need to evacuate or isolate the area
according to your local emergency plan. Use water spray to keep fire exposed containers
cool.
Unusual Fire Hazards: Vapors are heavier than air and may travel to a source of ignition and flash back. Static
electricity will accumulate and may ignite vapors. Prevent a possible fire hazard by
bonding and grounding or inert gas purge. Fire burns more vigorously than would be
expected.
2 OF 9
TM
MATERIAL SAFETY DATA SHEET
BONDAFLEX SIL 2300 PRIMER
Hazardous Decomposition Products
Thermal breakdown of this product during fire or very high heat conditions may evolve the following hazardous
decomposition products: Carbon oxides and traces of incompletely burned carbon compounds. Silicon dioxide.
Formaldehyde. Metal oxides.
SECTION 6 鈥? ACCIDENTAL RELEASE MEASURES
Containment/Clean up: Remove possible ignition sources. Determine whether to evacuate or isolate the area
according to your local emergency plan. Observe all personal protection equipment
recommendations described in Sections 5 and 8. For large spills, provide diking or other
appropriate containment to keep material from spreading. If diked material can be
pumped, store recovered material in appropriate container. Clean up remaining materials
from spill with suitable absorbant. Clean area as appropriate since spilled materials, even
in small quantities, may present a slip hazard. Final cleaning may require use of steam,
solvents or detergents. Dispose of saturated absorbant or cleaning materials
appropriately, since spontaneous heating may occur. Local, state and federal laws and
regulations may apply to releases and disposal of this material, as well as those materials
and items employed in the cleanup of releases. You will need to determine which federal,
state and local laws and regulations are applicable. Sections 13 and 15 of this MSDS
provide information regarding certain federal and state requirements.
Note: See section 8 for Personal Protective Equipment for Spills.
SECTION 7 鈥? HANDLING AND STORAGE
Use with adequate ventilation. Product evolves n-butyl alcohol when exposed to water or humid air. Provide
ventilation during use to control n-butyl alcohol within exposure guidelines or use respiratory protection. Product
evolves propylene glycol monomethyl ether when exposed to water or humid air. Provide ventilation during use to
control propylene glycol monomethyl ether within exposure guidelines or use respiratory protection. Product
evolves n-propyl alcohol when exposed to water or humid air. Provide ventilation during use to control n-propyl
alcohol within exposure guidelines or use respiratory protection. Avoid eye contact. Avoid skin contact. Do not
breathe vapor, mist, dust, or fumes. Keep container closed. Do not take internally.
Static electricity will accumulate and may ignite vapors. Prevent a possible fire hazard by bonding and grounding or
inert gas purge. Keep container closed and away from heat, sparks, and flame. Keep container closed and store
away from water or moisture.
SECTION 8 鈥? EXPOSURE CONTROLS/PERSONAL PROTECTION
Component Exposure Limits
CAS Number Component Name Exposure Limits
107-51-7 Octamethyltrisiloxane TWA 200 ppm.
5593-70-4 Tetrabutyl titanate See n-butyl alcohol comments.
18407-95-9 1-Methoxyisopropyl orthosilicate See propylene glycol monomethyl ether comments.
682-01-9 Tetrapropyl orthosilicate See n-propyl alcohol comments.
Propylene glycol monomethyl ether is formed on contact with water or humid air. Provide adequate ventilation to
3 OF 9
TM
MATERIAL SAFETY DATA SHEET
BONDAFLEX SIL 2300 PRIMER
control exposures within guidelines of OSHA PEL (final rule) and ACGIH TLV: TWA 100 ppm and STEL 150
ppm. n-Propyl alcohol is formed upon contact with water or humid air. Provide adequate ventilation to control
exposures within guidelines of OSHA PEL (final rule): TWA 200 ppm, STEL 250 ppm. ACGIH TLV: TWA 200
ppm, STEL 400 ppm. n-Butyl alcohol is formed on contact with water or humid air. Provide adequate ventilation
to control exposures within guidelines of OSHA PEL (final rule): TWA 100 ppm and ACGIH TLV: 20 ppm.
Engineering Controls
Local Ventilation: Recommended.
General Ventilation: Recommended.
Personal Protective Equipment for Routine Handling
Eyes: Use chemical worker's goggles.
Skin: Wash at mealtime and end of shift. If skin contact occurs, change contaminated clothing
as soon as possible and thoroughly flush affected areas with cool water. Chemical
protective gloves are recommended.
Suitable Gloves: Nitrile Rubber. Neoprene Rubber(R). Butyl Rubber.
Inhalation: Use respiratory protection unless adequate local exhaust ventilation is provided or air
sampling data show exposures are within recommended exposure guidelines. Industrial
Hygiene Personnel can assist in judging the adequacy of existing engineering controls.
Suitable Respirator: General and local exhaust ventilation is recommended to maintain vapor exposures
below recommended limits. Where concentrations are above recommended limits as
determined by air sampling or are unknown, appropriate respiratory protection should be
worn. Follow OSHA Respirator Regulations (29 CFR 1910.134) and use NIOSH/MSHA
approved respirators.
Personal Protective Equipment for Spills
Eyes: Use full face respirator.
Skin: Wash at mealtime and end of shift. If skin contact occurs, change contaminated clothing
as soon as possible and thoroughly flush affected areas with cool water. Chemical
protective gloves are recommended.
Inhalation/Suitable
Respirator: Respiratory protection recommended. Follow OSHA Respirator Regulations (29 CFR
1910.134) and use NIOSH/MHSA approved respirators. Protection provided by air
purifying respirators against exposure to any hazardous chemical is limited. Use a
positive pressure air supplied respirator if there is any potential for uncontrolled release,
exposure levels are unknown, or any other circumstance where air purifying respirators
may not provide adequate protection.
Precautionary Measures: Avoid eye contact. Avoid skin contact. Do not breathe vapor, mist, dust, or fumes. Keep
container closed. Do not take internally. Use reasonable care.
4 OF 9
TM
MATERIAL SAFETY DATA SHEET
BONDAFLEX SIL 2300 PRIMER
Comments: Product evolves n-butyl alcohol when exposed to water or humid air. Provide ventilation
during use to control n-butyl alcohol within exposure guidelines or use respiratory
protection. Product evolves propylene glycol monomethyl ether when exposed to water
or humid air. Provide ventilation during use to control propylene glycol monomethyl ether
within exposure guidelines or use respiratory protection. Product evolves n-propyl
alcohol when exposed to water or humid air. Provide ventilation during use to control
n-propyl alcohol within exposure guidelines or use respiratory protection.
Note: These precautions are for room temperature handling. Use at elevated temperature or aerosol/spray applications may
require added precautions.
SECTION 9 鈥? PHYSICAL AND CHEMICAL PROPERTIES
Physical Form: Liquid
Color: Colorless to pale yellow
Odor: Slight odor
Specific Gravity @ 25掳C: 0.820
Viscosity: 1 cSt
Freezing/Melting Point: Not determined.
Boiling Point: > 150 掳C
Vapor Pressure @ 25掳 C Not determined.
Vapor Density: Not determined.
Solubility in Water: Not determined.
pH: Not determined.
Volatile Content: Not determined.
Note: The above information is not intended for use in preparing product specifications.
SECTION 10 鈥? STABILITY AND REACTIVITY
Chemical Stability: Stable.
Hazardous
Polymerization: Hazardous polymerization will not occur.
Conditions to Avoid: None.
Materials to Avoid: Oxidizing material can cause a reaction. Water, moisture, or humid air can cause
hazardous vapors to form as described in Section 8.
SECTION 11 鈥? TOXICOLOGICAL INFORMATION
Special Hazard Information on Components
No known applicable information.
SECTION 12 鈥? ECOLOGICAL INFORMATION
Environmental Fate and Distribution
Complete information is not yet available.
5 OF 9
TM
MATERIAL SAFETY DATA SHEET
BONDAFLEX SIL 2300 PRIMER
Environmental Effects
Complete information is not yet available.
Fate and Effects in Waste Water Treatment Plants
Complete information is not yet available.
Ecotoxicity Classification Criteria
Hazard Parameters (LC50 or EC50) High Medium Low
Acute Aquatic Toxicity (mg/L) <=1 >1 and <=100 >100
Acute Terrestrial Toxicity <=100 >100 and <= 2000 >2000
This table is adapted from "Environmental Toxicology and Risk Assessment", ASTM STP 1179, p.34, 1993.
This table can be used to classify the ecotoxicity of this product when ecotoxicity data is listed above.
Please read the other information presented in the section concerning the overall ecological safety of this material.
SECTION 13 鈥? DISPOSAL CONSIDERATIONS
RCRA Hazard Class (40 CFR 261)
When a decision is made to discard this material, as received, is it classified as a hazardous waste? Yes
Characteristic Waste:
Ignitable: D001
State or local laws may impose additional regulatory requirements regarding disposal.
SECTION 14 鈥? TRANSPORT INFORMATION
DOT Road Shipment Information (49 CFR 172.101)
Proper Shipping Name: FLAMMABLE LIQUID, N.O.S.
Hazard Technical Name: OCTAMETHYLTRISILOXANE/TETRABUTYL TITANATE
Hazard Class: 3
UN/NA Number: UN1993
Packing Group: III
Hazard Label(s): FLAMMABLE LIQUID LABEL
6 OF 9
TM
MATERIAL SAFETY DATA SHEET
BONDAFLEX SIL 2300 PRIMER
Ocean Shipment (IMDG)
Proper Shipping Name: FLAMMABLE LIQUID, N.O.S.
Hazard Technical Name: OCTAMETHYLTRISILOXANE/TETRABUTYL TITANATE
Hazard Class: 3
UN Number: 1993
Packing Group: III
Hazard Label(s): FLAMMABLE LIQUID
Marine Pollutant: Not Applicable
Air Shipment (IATA)
Proper Shipping Name FLAMMABLE LIQUID, N.O.S.
Hazard Technical Name: OCTAMETHYLTRISILOXANE/TETRABUTYL TITANATE
Hazard Class: 3
UN Number: 1993
Packing Group: III
Hazard Label(s): FLAMMABLE LIQUID
SECTION 15 鈥? REGULATORY INFORMATION
Contents of this MSDS comply with the OSHA Hazard Communication Standard 29 CFR 1910.1200.
TSCA Status: All chemical substances in this material are included on or exempted from listing on the TSCA
Inventory of Chemical Substances.
EPA SARA Title III Chemical Listings
Section 302 Extremely Hazardous Substances:
None.
Section 304 CERCLA Hazardous Substances:
None.
Section 312 Hazard Class:
Acute: Yes
Chronic: No
Fire: Yes
Pressure: No
Reactive: No
7 OF 9
TM
MATERIAL SAFETY DATA SHEET
BONDAFLEX SIL 2300 PRIMER
Section 313 Toxic Chemicals:
None present or none present in regulated quantities.
Supplemental State Compliance Information
California
Warning: This product contains the following chemical(s) listed by the State of California under the Safe Drinking
Water and Toxic Enforcement Act of 1986 (Proposition 65) as being known to cause cancer, birth defects or other
reproductive harm.
None known.
Massachusetts
No ingredient regulated by MA Right-to-Know Law present.
New Jersey
CAS Number Wt % Component Name
107-51-7 > 60.0 Octamethyltrisiloxane
5593-70-4 5.0 - 10.0 Tetrabutyl titanate
18407-95-9 5.0 - 10.0 1-Methoxyisopropyl orthosilicate
682-01-9 5.0 - 10.0 Tetrapropyl orthosilicate
Pennsylvania
CAS Number Wt % Component Name
107-51-7 > 60.0 Octamethyltrisiloxane
5593-70-4 5.0 - 10.0 Tetrabutyl titanate
18407-95-9 5.0 - 10.0 1-Methoxyisopropyl orthosilicate
682-01-9 5.0 - 10.0 Tetrapropyl orthosilicate
8 OF 9
TM
MATERIAL SAFETY DATA SHEET
BONDAFLEX SIL 2300 PRIMER
SECTION 16 鈥? OTHER INFORMATION
These data are offered in good faith as typical values and not as product specifications. No warranty, either
expressed or implied, is hereby made. The recommended industrial hygiene and safe handling procedures are
believed to be generally applicable. However, each user should review these recommendations in the specific
context of the intended use and determine whether they are appropriate
9 OF 9
|