Product Name: THER-O-BOND 1600 HARDENER
MSDS No.: 21-000047
Date Revised: 03/29/2001
28 Norfolk Avenue 鈥? Easton Industrial Park 鈥? South Easton, MA 02375 鈥? Phone: 508.230.8070 鈥? Fax: 508.230.2318 Page: 1 of 4
RESIN TECHN OLOGY GROUP, LLC
MATERIAL SAFETY DATA SH EET
1. MATERIAL IDENTIFICATION
THER-O-BOND 1600 HARDENER
Product Name:
EMERGENCY PHONE: For product emergency involving spill, leak, fire, exposure, or accident call CHEMTREC at (800)
424-9300. For all other inquiries please call Resin Technology Group, LLC. at (508) 230-8070.
2. COMPOSITION Exposure Limits
ACGIH OSHA
HAZARDOUS COMPONENTS CAS NO. PERCENT TLV-TWA PEL
Tetraethylenepentamine (TEPA) 112-57-2 <92 N.E. N.E.
Triethylenetetramine (TETA) 112-24-3 <5 N.E. N.E.
Polyethylenepolyamine mixture 29320-38-5 <5 N.E. N.E.
Abbreviations: N.E.: Not Established.
3. HEALTH HAZARDS IDENTIFICATION
Routes of Exposure: Eyes: Yes Skin: Yes Inhalation: Yes
Eye Contact: Corrosive. Contact can cause severe irritation. Contact may result in severe damage and blindness.
Skin Contact: Corrosive. Contact can cause severe damage. May cause skin sensitization. May be toxic if absorbed through skin.
Inhalation: Vapors/mists may be corrosive to upper respiratory tract. Repeated or prolonged exposure can result in lung
damage. May cause respiratory tract sensitization.
Ingestion: Not expected to be a relevant route of exposure, however, corrosive and may cause severe and permanent damage to
mouth, stomach and throat.
4. FIRST AID MEASURES
Eyes: Flush eyes with water for at least 15 minutes while holding eyelids open. Seek medical attention immediately.
Skin: Remove contaminated clothing and shoes. Wipe excess from skin. Flush skin with water. Follow by washing area
thoroughly with soap and water. If irritation occurs, seek medical attention. Do not reuse clothing until laundered.
Inhalation: Remove to fresh air, and provide oxygen if breathing is difficult. Seek medical attention promptly.
Ingestion: DO NOT induce vomiting. Give one glass of water unless victim is drowsy, convulsing or unconscious. Seek
medical attention promptly.
Product Name: THER-O-BOND 1600 HARDENER
MSDS No.: 21-000047
Date Revised: 03/29/2001
Page: 2 of 4
5. FIRE FIGHTING MEASURES
FLAMMABLE PROPERTIES
320 oF (PMCC)
Flashpoint:
Explosive Limits: Not available.
Auto - Ignition Temperature: Not available.
Hazardous Combustion Products: Nitrogen oxides, carbon monoxide and unidentified organic compounds may be formed
during combustion.
Fire Fighting Instructions: Material will not burn unless preheated. Firefighters should be equipped with full protective gear,
including a positive pressure NIOSH approve self-contained breathing apparatus.
Extinguishing Media: Use water fog, alcohol foam, dry chemical or carbon dioxide.
6. ACCIDENTAL RELEASE MEASURES
Danger, Corrosive. Prevent all bodily contact with spilled material. Wear respirator and protective clothing as appropriate.
Eliminate potential fire hazards. Soak up residue with an absorbent such as clay, sand or other suitable material; place in non-leaking
containers for proper disposal. Flush area with water to remove last traces of residue.
7. HANDLING AND STORAGE
Store in a cool, dry place. Keep away from open flames and high temperatures. Avoid all ignition sources and reactive materials.
Avoid contact with eyes. Wear safety goggles as appropriate. Avoid contact with skin. Wear chemical-resistant gloves and other
protective clothing as required to minimize contact.
8. EXPOSURE CONTROLS and PERSONNEL PROTECTION
Engineering/Ventilation Controls: General ventilation and local exhaust may be required to maintain airborne concentrations
below the established exposure limits exposure when generating vapors or mists.
Respiratory Protection: Where exposure exceeds established airborne limits, use a NIOSH approved respirator, or a
self-contained breathing apparatus, or a supplied air respirator as necessary to control exposure.
Skin Protection: Wear impervious gloves and protective clothing as necessary to prevent skin contact.
Eye Protection: Wear chemical splash goggles or safety glasses with side shields.
9. PHYSICAL AND CHEMICAL PROPERTIES
Appearance: Clear amber liquid
Odor: Amine
605 oF
Boiling Point:
Specific Gravity: 0.98
<1.0 @ 20 oC
Vapor Pressure (mm Hg):
Vapor Density (air=1): Not available
Evaporation Rate: Not available
Solubility in Water: Partial
Product Name: THER-O-BOND 1600 HARDENER
MSDS No.: 21-000047
Date Revised: 03/29/2001
Page: 3 of 4
10. STABILITY AND REACTIVITY
Chemical Stability: Stable under normal conditions and use.
Conditions to avoid: Avoid heat, flame and contact with strong oxidizing agents.
Hazardous Combustion Products: Nitrogen oxides, carbon monoxide and unidentified organic compounds may be formed
during combustion
Hazardous Polymerization: Will not occur.
11. TOXICOLOGICAL INFORMATION
This section provides toxicological information with regard to the pure form of the components indicated. This information can
be subject to misinterpretation. It is therefore suggested that persons trained in its evaluation interpret this information.
LD50 Acute Oral Rat: 3.99 g/kg
LD50 Acute Dermal Rabbit: 0.66 g/kg
300 mg/m3
LC50 Acute Inhalation Mouse:
12. ECOLOGICAL INFORMATION
No data found.
13. DISPOSAL CONSIDERATIONS
Keep out of surface waters, sewers, and waterways entering or leading to surface waters. Notify authorities if any exposure to the
general public or environment occurs or is likely to occur. Place in an appropriate disposal facility in compliance with applicable
governmental regulations.
14. TRANSPORT INFORMATION
D.O.T. Classification: Tetraethylenepentamine
Hazard Class: 8 UN #: UN2320 PG: III ERG #: 153 Hazard Labels: Corrosive
I.A.T.A. Classification: Tetraethylenepentamine
Hazard Class: 8 UN #: UN2320 PG: III ERG #: 153 Hazard Labels: Corrosive
Product Name: THER-O-BOND 1600 HARDENER
MSDS No.: 21-000047
Date Revised: 03/29/2001
Page: 4 of 4
15. REGULATORY INFORMATION
US FEDERAL REGULATIONS
TSCA:
The chemical components of this product are contained on section 8(B) of the chemical substance inventory list (40 CFR 710)
SARA Title III Information
Section 313 - Toxic Chemicals:
This product contains the following chemicals subject to reporting requirements: None.
Section 311/312 - Hazard Categories:
Fire Hazard: No
Reactivity Hazard: No
Sudden Release of Pressure Hazard: No
Immediate (Acute) Health Hazard: Yes
Delayed (Chronic) Health Hazard: Yes
STATE REGULATIONS / RIGHT TO KNOW
California Proposition 65: This product does not contain a chemical or chemicals known to the State of California to cause birth
defects or other reproductive harm.
Pennsylvania: All of the materials in this product requiring identification by the Commonwealth of Pennsylvania are
listed in section 2.
16. OTHER INFORMATION
HMIS Hazards: Health: 3 Flammability: 1 Reactivity: 0
NFPA Hazards: Health: 3 Flammability: 1 Reactivity: 0
This information is intended solely for the use of individuals trained in the use of this particular system.
Resin Technology Group, LLC urges each customer or recipient of this MSDS to study it carefully in order to become aware of
and understand the hazards associated with the product. The reader should consider consulting reference works or individuals that are
experts in ventilation, toxicology, and fire prevention, as necessary or appropriate in order to use and understand the data contained in
this MSDS.
To promote safe handling, each customer or recipient should: 1 - notify its employees, agents, contractors, and others whom it
knows or believes will use this material or the information in this MSDS and any other information regarding hazards or safety. 2 -
furnish this same information to each of its customers for the product. 3 - request its customers to notify their employees, customers,
and other users of the product of this information.
The information contained herein is based on the data available to us and is believed to be correct. However, Resin Technology
Group, LLC makes no warranty, expressed or implied regarding the accuracy of this data or the results to be obtained from the use
thereof. Resin Technology Group, LLC assumes no responsibility for injury from the use of the product described herein.
|