802358PM Page 1 of 8
04-10-2002
MATERIAL SAFETY DATA SHEET
__________________________________________________________________________________________
03-12-2002 06-13-2001
REVISION DATE: SUPERSEDES:
SECTION 1: CHEMICAL PRODUCT AND COMPANY IDENTIFICATION
COMPANY INFORMATION
Foster Products Corporation
H.B. Fuller Company Subsidiary
2900 Granada Lane
Oakdale, MN 55128
Phone: 651-236-3700
Medical Emergency Phone Number (24 Hours): 1-888-853-1758
Transport Emergency Phone Number (CHEMTREC): 1-800-424-9300
PRODUCT INFORMATION
PRODUCT IDENTIFIER: 802358PM
PRODUCT NUMBER: FD6095
PRODUCT NAME: FOSTER 60-95
TRADEMARK: MONOLAR COATING (WHITE)鈩?
PRODUCT DESCRIPTION: Coating
SECTION 2: COMPOSITION/INFORMATION ON INGREDIENTS
Unlisted ingredients are not 'hazardous' per the Occupational Safety and Health Administration Hazard
Communication Standard (29 CFR 1910.1200) and/or are not found on the Canadian Workplace Hazardous
Materials Information System ingredient disclosure list. See Section 8 for any additional exposure limit guidelines.
Chemical Name CAS # PERCENT OSHA PEL
Aromatic petroleum distillate 64742-95-6 30 - 50 Not established
Trimethylbenzene, 1,2,4- 95-63-6 10 - 30 Not established
Aluminum silicate of potash and soda. 68476-25-5 10 - 30 TWA (as Al) (Total dust) 15 MG/M3
TWA (as Al) (Respirable dust) 5 MG/M3
Chlorinated paraffin 63449-39-8 10 - 30 Not established
Titanium dioxide 13463-67-7 5 - 10 TWA (Total dust) 10 MG/M3
Crystalline silica 14808-60-7 5 - 10 TWA (Respirable dust) 0.1 MG/M3
Cumene 98-82-8 1-5 TWA 50 ppm
Skin notation
Xylene 1330-20-7 1-5 TWA 100 ppm
STEL 150 ppm
Propoxyethanol, 2- 2807-30-9 1-5 Not established
Tetraalkyl ammonium synectite 71011-27-3 1-5 Not established
802358PM Page 2 of 8
04-10-2002
MATERIAL SAFETY DATA SHEET
__________________________________________________________________________________________
Antimony trioxide 1309-64-4 0.1 - 1 TWA (as Sb) 0.5 MG/M3
SECTION 3: HAZARDS IDENTIFICATION
EMERGENCY OVERVIEW
Combustible
Moderate respiratory tract irritant.
Harmful if swallowed.
Cancer hazard.
HMIS RATING: HEALTH -- 1 FLAMMABILITY -- 2 REACTIVITY -- 0
See SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION for personal protective equipment
recommendations.
POTENTIAL HEALTH EFFECTS BY ROUTE OF ENTRY
EYE: Can cause minor irritation, tearing and reddening.
SKIN: Can cause minor skin irritation, defatting, and dermatitis.
INHALATION: Can cause moderate respiratory irritation. Inhalation of dusts produced during cutting, grinding or
sanding of this product may cause irritation of the respiratory tract.
Other possible symptoms include coughing or wheezing.
Inhalation of high concentrations may result in central nervous system (CNS) effects such as dizziness, weakness,
fatigue, nausea, headache, and lack of coordination. Overexposure to crystalline silica may cause silicosis.
INGESTION: Ingestion is not an anticipated route of exposure. Harmful if swallowed. Irritating to mouth, throat,
and stomach.
LONG-TERM (CHRONIC) HEALTH EFFECTS
REPRODUCTIVE: Contains a substance that is a probable reproductive hazard based on human
studies.
TARGET ORGAN(S): Blood Central nervous system Lungs Kidneys Liver
REGULATED CARCINOGEN STATUS:
Unless noted below, this product does not contain regulated levels of NTP, IARC, ACGIH, or OSHA listed
carcinogens.
Crystalline silica
Antimony trioxide
EXISTING HEALTH CONDITIONS AFFECTED BY EXPOSURE: Blood disorders (like anemia); Lung disease
802358PM Page 3 of 8
04-10-2002
MATERIAL SAFETY DATA SHEET
__________________________________________________________________________________________
SECTION 4: FIRST AID MEASURES
IF IN EYES: Immediately flush eyes with plenty of water for at least 20 minutes retracting eyelids often. Tilt the
head to prevent chemical from transferring to the uncontaminated eye. Get immediate medical attention and monitor
the eye daily as advised by your physician.
IF ON SKIN: Wash with soap and water. Remove contaminated clothing and launder. Get medical attention if
irritation develops or persists.
IF VAPORS INHALED: Remove to fresh air. Restore breathing, if necessary. Call a physician if symptoms
persist.
IF SWALLOWED: Do not induce vomiting and seek medical attention immediately. Drink two glasses of water or
milk to dilute. Do not give anything by mouth to an unconscious person. Induce vomiting as a last measure. Induced
vomiting may lead to aspiration of the material into the lungs potentially causing chemical pneumonitis that may be
fatal.
SECTION 5: FIRE FIGHTING MEASURES
FLASH POINT: 43C; 109F
AUTOIGNITION TEMPERATURE: Not established
LOWER EXPLOSIVE LIMIT (% in air): Not established
UPPER EXPLOSIVE LIMIT (% in air): Not established
EXTINGUISHING MEDIA: Use water spray, foam, dry chemical or carbon dioxide.
UNUSUAL FIRE AND EXPLOSION HAZARDS: Vapors are heavier than air and can travel to a source of ignition
and flash back.
SPECIAL FIRE FIGHTING INSTRUCTIONS: Persons exposed to products of combustion should wear self-
contained breathing apparatus and full protective equipment.
HAZARDOUS COMBUSTION PRODUCTS: Carbon dioxide, Carbon monoxide Chlorine containing gases
Sulfur containing gases Nitrogen containing gases
SECTION 6: ACCIDENTAL RELEASE MEASURES
SPECIAL PROTECTION: No health effects expected from the cleanup of this material if contact can be
avoided. Follow personal protective equipment recommendations found in
Section 8 of this MSDS. Evaporation of volatile substances can lead to the
displacement of air creating an environment that can cause asphyxiation.
CLEAN-UP: Dike if necessary, contain spill with inert absorbent and transfer to containers
for disposal. Keep spilled product out of sewers, watersheds, or water
systems.
Shut off ignition sources; including electrical equipment and flames. Do not
allow smoking in the area.
Transport Emergency Phone Number (CHEMTREC): 1-800-424-9300
SECTION 7: HANDLING AND STORAGE
Handling: Mildly irritating material. Avoid unnecessary exposure.
Keep away from heat, sparks and flame.
Wash thoroughly after handling.
Keep container closed.
Emptied container retains vapor and product residue.
Observe all labeled precautions until container is cleaned.
Drums of this material should be grounded when pouring.
DO NOT CUT OR WELD ON OR NEAR THIS CONTAINER.
802358PM Page 4 of 8
04-10-2002
MATERIAL SAFETY DATA SHEET
__________________________________________________________________________________________
Storage: Store in a cool, dry, ventilated location. Keep away from heat and flame. Keep container
closed.
Consult the Technical Data Sheet for specific storage instructions.
SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION
EYE PROTECTION: Wear safety glasses with side shields when handling this product.
Wear additional eye protection such as chemical splash goggles
and/or face shield when the possibility exists for eye contact with
splashing or spraying liquid, or airborne material. Have an eye wash
station available.
SKIN PROTECTION: Avoid skin contact by wearing chemically resistant gloves and long
sleeved shirt. An apron may be appropriate if splashing can occur.
Skin absorption may potentially contribute to the overall exposure to
this material. Appropriate measures should be taken to prevent
absorption so that the TLV is not invalidated.
GLOVES: Nitrile
RESPIRATORY PROTECTION: Respiratory protection may be required to avoid overexposure when
handling this product. Use a respirator if general room ventilation is
not available or sufficient to eliminate symptoms. NIOSH approved
air purifying respirator with organic vapor cartridge.
Respirators should be selected by and used following requirements
found in OSHA's respirator standard (29 CFR 1910.134).
VENTILATION: Use local exhaust ventilation or other engineering controls to
minimize exposures.
EXPOSURE LIMITS:
Chemical Name ACGIH EXPOSURE LIMITS AIHA WEEL
Aromatic petroleum distillate Not established Not established
Trimethylbenzene, 1,2,4- Not established Not established
Aluminum silicate of potash and TWA (as Al) (Total dust) 10 MG/M3 Not established
soda.
Chlorinated paraffin Not established Not established
Titanium dioxide TWA (Total dust) 10 MG/M3 Not established
Crystalline silica TWA (Respirable dust) 0.05 MG/M3 Not established
Cumene TWA 50 ppm Not established
Xylene TWA 100 ppm Not established
STEL 150 ppm
Propoxyethanol, 2- Not established Not established
802358PM Page 5 of 8
04-10-2002
MATERIAL SAFETY DATA SHEET
__________________________________________________________________________________________
Tetraalkyl ammonium synectite Not established Not established
Antimony trioxide TWA (as Sb) 0.5 MG/M3 Not established
SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
PHYSICAL STATE: Liquid
COLOR: White
ODOR: Solvent
ODOR THRESHOLD: Not established
WEIGHT PER GALLON (lbs.): 9.6
SPECIFIC GRAVITY: 1.17
SOLIDS (% by weight): 46.0
pH: Not established
BOILING POINT (deg. C): Not established
FREEZING/MELTING POINT (deg. C): Not established
VAPOR PRESSURE (mm Hg): Not established
VAPOR DENSITY: Not established
EVAPORATION RATE: Not established
OCTANOL/WATER COEFFICIENT: Not established
SECTION 10: STABILITY AND REACTIVITY
STABILITY: Stable under normal conditions.
CHEMICAL INCOMPATIBILITY: Strong oxidizing agents
HAZARDOUS POLYMERIZATION: Will not occur.
HAZARDOUS DECOMPOSITION PRODUCTS: Carbon monoxide, carbon dioxide Chlorine
containing gases Sulfur containing gases Nitrogen
containing gases
SECTION 11: TOXICOLOGICAL INFORMATION
CHEMICAL NAME LD50/LC50
Aromatic petroleum distillate Oral LD50 Rat = 8400 mg/kg
Trimethylbenzene, 1,2,4- Oral LD50 Rat = 5 g/kg
Inhalation LC50 Rat =18000 mg/cu m/4H
Aluminum silicate of potash and soda. Not established
Chlorinated paraffin Oral LD50 Rat >21500 ml/kg
Dermal LD50 Rabbit > 10 ml/kg
Titanium dioxide Not established
Crystalline silica Not established
Cumene Oral LD50 Rat = 1400 mg/kg
Inhalation LC50 Mouse =17500 mg/cu m/4H
802358PM Page 6 of 8
04-10-2002
MATERIAL SAFETY DATA SHEET
__________________________________________________________________________________________
Dermal LD50 Rabbit = 12.3 ml/kg
Xylene Oral LD50 Rat = 4300 mg/kg
Inhalation LC50 Rat = 5000 ppm/4H
Dermal LD50 Rat = 1700 mg/kg
Propoxyethanol, 2- Oral LD50 Rat = 3089 mg/kg
Inhalation LC50 Mouse = 2024 ppm/4H
Dermal LD50 Rabbit = 960 ml/kg
Tetraalkyl ammonium synectite Not established
Antimony trioxide Oral LD50 Rat >34600 mg/kg
TOXICOLOGY SUMMARY: No additional health information available.
SECTION 12: ECOLOGICAL INFORMATION
OVERVIEW: No ecological information available
634.7 g VOC/liter of material, less water and exempt solvents
(VOC theoretically determined using EPA Publication 450/3-84-019.)
SECTION 13: DISPOSAL CONSIDERATIONS
This product meets the definition of hazardous waste under the U.S. EPA Hazardous Waste Regulations 40 CFR
261. It is ignitable waste class D001. Disposal via incineration is recommended. Consult your state, local, or
provincial authorities for more restrictive requirements.
LAND DISPOSAL RESTRICTIONS: Xylenes (o-, m-, p- isomers)
SECTION 14: TRANSPORTATION INFORMATION
Consult Bill of Lading for transportation information.
DOT: COMBUSTIBLE LIQUID, N.O.S. (HI-FLASH NAPHTHA SOLUTION), , NA1993, PG.III
IATA: COATING SOLUTION , 3, UN1139, PG.III
SECTION 15: REGULATORY INFORMATION
INVENTORY STATUS
U.S. EPA TSCA: This product is in compliance with the Toxic Substances Control Act's
Inventory requirements.
If you need more information about the inventory status of this product call 651-236-5858.
TSCA Section 12(b) - Export Notice Requirements
This product contains a chemical substance that is currently on the EPA's Section 12(b) Export List. Contact the
company Global Regulatory Group at 651/236-5858 for the identity of the Section 12(b) chemical(s).
FEDERAL REPORTING
EPA SARA Title III Section 313
Unless listed below, this product does not contain toxic chemical(s) subject to the reporting requirements of section
313 of Title III of the Superfund Amendments and Reauthorization Act of 1986 (SARA) and 40 CFR part 72. EPA
has advised that when a percentage range is listed the midpoint may be used to fulfill reporting obligations.
Chemical Name CAS# %
1,2,4-Trimethylbenzene 95-63-6 10 - 30
Polychlorinated alkanes 63449-39-8 10 - 30
Cumene 98-82-8 1-5
Xylene (mixed isomers) 1330-20-7 1-5
802358PM Page 7 of 8
04-10-2002
MATERIAL SAFETY DATA SHEET
__________________________________________________________________________________________
Glycol ethers 2807-30-9 1-5
Ammonia containing compounds 71011-27-3 1-5
Antimony compounds 1309-64-4 0.1 - 1
This includes anhydrous ammonia and aqueous ammonia from water dissociable ammonium salts and other sources;
10% of total aqueous ammonia is reportable.
WHMIS STATUS: Unless listed below, this product is not controlled under the Canadian Workplace Hazardous
Materials Information System.
B3
D2A D2B D1B
STATE REPORTING
This MSDS is not prepared for distribution in California.
SECTION 16: ADDITIONAL INFORMATION
This Material Safety Data Sheet is prepared to comply with the United States Occupational Safety and Health
Administration (OSHA) Hazard Communication Standard (29 CFR 1910.1200) and the Canadian Workplace
Hazardous Materials Information System (WHMIS).
Prepared by: The Global Regulatory Department
Phone: 651-236-5842
The information and recommendations set forth herein are believed to be accurate. Because some of the information
is derived from information provided to Foster Products Corporation from its suppliers, and because Foster Products
Corporation has no control over the conditions of handling and use, Foster Products Corporation makes no warranty,
expressed or implied, regarding the accuracy of the data or the results to be obtained from the use thereof. The
information is supplied solely for your information and consideration, and Foster Products Corporation assumes no
responsibility for use or reliance thereon. It is the responsibility of the user of Foster Products Corporation products
to comply with all applicable federal, state and local laws and regulations.
|