TARGET COATINGS, Inc.
PO BOX 1582
RUTHERFORD, NJ 07070 USA
800-752-9922
www.targetcoatings.com
MATERIAL SAFETY DATA SHEET PAGE 1 OF 4
____________________________________________________________________________________________
SECTION I PRODUCT IDENTIFICATION
____________________________________________________________________________________
Product Trade Name: SA5 Retarder
(SA508, SA532)
Chemical Name: Compound, Coating
Manufacturer: Target Coatings, Inc.
Effective Date: January 1, 2003..Revision 1
____________________________________________________________________________________
SECTION II PHYSICAL DATA
____________________________________________________________________________________
Boiling Point: 212 F
Freezing Point: 30F
Weight Per Gallon: 8.5 lbs./Gal.
Vapor Density: Heavier then Air.
Evaporation Rate: Slower then N-Butyl Acetate
Solubility in Water: Infinitely miscible
pH: 7.5
Appearance and Odor: Clear Liquid, Glycol Odor
VOC Content: 250 Grams/Liter, 1.89 lbs./Gal.
HAPS Content: 0
____________________________________________________________________________________
SECTION III COMPOSITION INFORMATION
____________________________________________________________________________________
INGREDIENT Approx. Wt% SARA-313 CAS#
Dipropylene Glycol Monomethyl Ether 50.0 max. N/A 34590-94-8
Performance Additive 05.0 max. N/A Proproetary
Water 45 min. N/A 7732-18-5
____________________________________________________________________________________
SECTION IV HAZARDOUS INGREDIENTS
____________________________________________________________________________________
INGREDIENT Approx. Wt% TLV PEL(TWA) STEL CAS#
None Of The Ingredients In This Product Meet The Definition Of 鈥淗azardous Chemical鈥? Given
In The OSHA Hazard Communication Regulation 29CFR 1910.120 (C)
____________________________________________________________________________________
MATERIAL SAFETY DATA SHEET PAGE 2 OF 4
____________________________________________________________________________________________
SECTION V TOXICOLOGICAL PROPERTIES
____________________________________________________________________________________________
LD50: Not determined
Threshold Limit Value: No limit determined
Effects of Acute Exposure:
Ingestion: Intense mucous membrane irritation
Inhalation: Prolonged exposure may produce
headaches, and mucous membrane
irritation.
Skin Contact: Direct contact will cause irritation
Eye Contact: Direct contact will cause extensive irritation
Effects of Chronic Exposure: None determined
____________________________________________________________________________________
SECTION VI PREVENTIVE MEASURES
____________________________________________________________________________________
INDUSTRIAL HYGIENE IN THE WORKPLACE
RESPIRATORY PROTECTION: None required in well ventilated areas. An approved organic-
vapor full-face respirator is advised for poor ventilation or spray applications.
VENTILATION: LOCAL EXHAUST- None required
MECHANICAL(GENERAL)- Provide adequate ventilation.
PROTECTIVE GLOVES: Wear rubber gloves.
EYE PROTECTION: Wear approved safety glasses with side shields.
OTHER PROTECTIVE EQUIPMENT: Wear protective work clothes.
STORAGE AND HANDLING PROCEDURES
PRECAUTIONS TO BE TAKEN IN HANDLING AND STORAGE: store at 40F-90F. this product is
safe for consumer resale. Keep from freezing. Keep away from Fire and Heat (Any ignition source).
Keep containers closed when not in use. Provide adequate ventilation.
KEEP OUT OF REACH OF CHILDREN
STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED: Halt spill at source and
contain or dike spill with inert absorbent material. Transfer liquid to containers for recovery or disposal.
Shovel absorbent into drums for disposal in accordance with local, state, and federal regulations.
RECOMMENDED WASTE DISPOSAL METHODS: Material should not be flushed into sewer system.
If this material becomes a waste, it does not meet the criteria of a hazardous waste as defined under the
Resource Conservation and Recovery Act (RCRA) 40 CFR 261, since it has neither the characteristics of
Subpart C nor listed in Subpart D. After the material has been collected, dispose of in accordance with
regulations applicable to non-hazardous liquid wastes.
MATERIAL SAFETY DATA SHEET Page 3 of 4
____________________________________________________________________________________
SECTION VII FIRST AID MEASURES
__________________________________________________________________
EMERGENCY FIRST AID PROCEDURES
INGESTION: Do not induce vomiting. Administer large amounts of milk and call a physician.
INHALATION: Remove to fresh air and consult with a physician if symptoms persist.
SKIN CONTACT: Promptly wash area with soap and water, and rinse thoroughly. Remove
contaminated clothing.
EYE CONTACT: Promptly flush eyes with large amounts of fresh water for at leas 15 minutes.
Contact a physician immediately.
____________________________________________________________________________________
SECTION VIII REGULATORY INFORMATION
__________________________________________________________________
SUPERFUND AMENDMENT AND REAUTHORIZATION ACT OF 1986 (SARA TITLE III)
SECTION 302- EXTREMELY HAZARDOUS SUBSTANCES (40 CFR 355): This product does not
contain materials listed in Appendix A and B as an Extremely Hazardous Substance.
SECTION 311/312- MATERIAL SAFETY DATA SHEET REQUIREMENTS (40 CFR 370): Materials
listed in 29 CFR 1910, Subpart Z is identified in Section IV. None are known or suspected carcinogens
listed by the National Toxicology Program, International Agency of Research on Cancer, or OSHA.
SECTION 313- LIST OF TOXIC CHEMICALS (40 CFR 372): Listed materials contained in this product
are identified in Sections II or IV of this MSDS.
TOXIC SUBSTANCES CONTROL ACT (TSCA)
Not available
CLEAN AIR ACT AMENDMENT OF 1990
This product does not contain, and has not contacted during manufacture, any Ozone depleting
Substances.
__________________________________________________________________________________
SECTION IX FIRE AND EXPLOSION HAZARD DATA
__________________________________________________________________
FLASH POINT: Greater than 200 F
AUTOIGNITION TEMPERATURE: N/A
EXTINGUISHING MEDIA: Water mist, Foam, CO2, dry chemical.
FLAMMABLE LIMITS: LOWER: Not Applicable
UPPER: Not Applicable
SPECIAL FIREFIGHTING PROCEDURES: Toxic gasses may be released. Use self-contained
breathing apparatus.
UNUSUAL FIRE/EXPLOSIVE HAZARDOUS: None.
MATERIAL SAFETY DATA SHEET Page 4 of 4
__________________________________________________________________
SECTION X HAZARD RATING INFORMATION
__________________________________________________________________
HMIS HAZARD RATING:
4= EXTREME TOXICITY= 2
3= HIGH FIRE= 0
2= MODERATE REACTIVITY= 0
1= SLIGHT SPECIAL= G
0= INSIGNIFICANT
____________________________________________________________________________________
SECTION XI REACTIVITY DATA
__________________________________________________________________
STABILITY: Stable
CONDITIONS TO AVOID: Temperatures of 212F or over will cause boiling of water.
INCOMPATIBILITY: Treat as water.
HAZARDOUS POLYMERIZATION: Will not occur.
HAZARDOUS DECOMPOSITION PRODUCTS: Thermal decomposition on burning may produce
toxic gasses.
____________________________________________________________________________________
SECTION XII USER'S RESPONSIBILITY
Target Coatings cannot anticipate all conditions of handling and use of this product. Therefore, Target
Coatings accepts no responsibility for results obtained by application of this information, or safety and
suitability of our products either alone or in combination with other products. It is the responsibility of
the user to provide a safe workplace, using the health and safety information contained herein as a guide.
Target Coatings will accept no liability for damages or loss incurred from the improper handling and use
of this product.
____________________________________________________________________________________
SECTION XIII SPECIAL PRECAUTIONS
PRECAUTION: READ MSDS BEFORE USE
____________________________________________________________________________________
SECTION XIV PREPARATION INFORMATION
This Material Safety Data Sheet was prepared by:
Jeff Weiss Telephone Number: 1-800-752-9922
|