GENERAL FINISHES
PO Box 510567 New Berlin, WI 53151
800-783-6050 Fax 262-786-6509
Water Base Pre-Cat 181 Urethane
Classification: Product Data:
Water Based Pre-Catalyzed Urethane Finish
飩稤ensity:
飥? 8.6 +/- 0.2 lbs.
飩稺eight Solids:
飥?
Product Description: 20.5 - 24.5%
Pre-Cat 181 Urethane water base finish is a highly ad- 飩稸olume Solids:
飥? 18.5 - 22.5%
vanced polyurethane coating. The pre-catalyzed technol-
飩稸iscosity:
飥? 35 - 45 seconds
ogy is designed to provide maximum performance proper-
飩稭ethod:
飥? Ford #4 @ 77 F.
ties; Pre-Cat 181 Urethane delivers excellent toughness,
飩穚H:
飥? 7.0 - 8.0
durability, and water resistance typically associated only
with solvent based pre-catalyzed finishes. However, Pre- 飩稸.O.C.:
飥? 250 g/l ( 2.09 lbs/gal)
Cat 181 Urethane is water base, VOC-Compliant, low odor, excluding water
飩?% VOC:
飥?
non-flammable, and will clean-up with soap and water. It 6.7%
is self-sealing, and typically does not require thinning.
飩稴torage:
飥? Protect from Freezing
F r ltdt v r lw V Cs(5 gl P e
omuae o ey o O 鈥? 2 0 /, r-Cat 181 Ure-
)
thane dries very quickly for topcoating.
Container:
Application:
Ones, Fives and Drums
Brush: Stir well before application. Use a quality foam
bu h S ry C mpe s dar04 鈥? f i t / du
rs . pa : o rs e i .0 l d i me im
: up
Sheen:
c p H L : .5 鈥? li t / du c p; ie s 00 9
a ; V P 00 1 f d i me im a Ar s : .0 鈥?
up l
Satin, Semi-gloss and Gloss
tip. Allow 30 minutes -2 hours dry before sanding
(temperature / humidity dependent). 3 - 5 coats recom-
70OF and 70% R.H:
Dry Time
mended.
飩稤ry:
飥? 10 - 20 minutes
飩稵o Sand:
飥? 30 minutes -2 hours
GENERAL FINISHES
鈥渉 C u t 鈥? ie FlLn M n f tr oWod ii ig rdc鈥?
T e onr s ns ul ie au c e f o F s n Pout
yF t au r nh s
www.generalfinishes.com
GENERAL FINISHES
PO Box 510567 New Berlin, WI 53151 800-783-6050
Application:
Mixing and Application:
飩稢onventional Spray:
飥?
飩?
飥燙atalyst Ratio: None
飩稟ir Assisted Airless
飥?
飩?
飥? Life:
Pot Not Applicable
飩稨VLP
飥?
飩?
飥燬helf Life: 1 year, minimum 飩稡rush
飥?
飩?
飥燫educer/Thinner: EF Extender (10 鈥?20%)
Stain & Sealer Recommendation:
Can be used over most water base and solvent base
stains. For best results and superior color and adhesion,
Cautions:
General Finishes EF Water Base Stains and GF Oil Base
飩稭ix container before use
飥?
Stains are recommended. Allow stains to dry thoroughly
飩稦or industrial use only
飥?
before topcoating.
飩稰rotect from freezing
飥?
Pre-Cat 181 Urethane may be used over solvent base and 飩稲ead MSDS for safety information
飥?
water base paints. Allow paints to dry before thoroughly
before topcoating.
飩稢lean-up
飥? Information:
Pre-Cat 181 Urethane is designed to be self-sealing.
For best results, clean all equipment
However General Finishes EF Sanding Sealer should be
with General Finishes Brush and Gun
used for optimal performance.
Cleaner. General clean-up with soap
and water recommended. Rinse
Surface Preparation:
thoroughly with clean water.
Surface must be clean, dry, and free of all contaminants.
Sand with 220 grit or finer between coats. Consult product
label for additional information.
Pre-Cat 181 Urethane
062705
NOTICE: All of the above statements, recommendations, suggestions, and data concerning the subject material are based on laboratory results and
believed to be reliable. We expressly do not represent, warrant, or guarantee the accuracy, completeness or reliability of same, or the material or
the results to be obtained from the use thereof, neither do we warrant that any such use, either alone or in combination with other materials shall be
free of the rightful claim of any third party by way of INFRINGEMENT or the like and (THE MANUFACTURER DISCLAIMS ALL
WARRANTIES, EXPRESSED OR IMPLIED,) OF MERCHANTABILITY and FITNESS FOR A PARTICLUAR PURPOSE.
|