LTIMSDS1
______________________________________________________________________________
MATERIAL SAFETY DATA SHEET
__________________________ Page 1 of 8
Revised 6/09/04
E-PAGE BUFFER #1, 4X Replaces 4/01/04
INVITROGEN CORPORATION Printed 8/31/04
MSDS ID: EPBUF01
______________________________________________________________________________
______________________________________________________________________________
1. PRODUCT AND COMPANY INFORMATION
______________________________________________________________________________
INVITROGEN CORPORATION GIBCO PRODUCTS
1600 FARADAY AVE. INVITROGEN CORPORATION
CARLSBAD, CA 92008 3175 STALEY ROAD P.O. BOX 68
760/603-7200 GRAND ISLAND, NY 14072
716/774-6700
INVITROGEN CORPORATION INVITROGEN CORPORATION
3 FOUNTAIN DR. P.O. BOX 12-502
INCHINNAN BUSINESS PARK PENROSE
PAISLEY, PA4 9RF AUCKLAND 1135
SCOTLAND NEW ZEALAND
44-141 814-6100 64-9-579-3024
INVITROGEN CORPORATION INVITROGEN AUSTRALIA PTY LIMITED
2270 INDUSTRIAL ST. 2A/14 LIONEL ROAD
BURLINGTON, ONT MOUNT WAVERLY VIC 3149
CANADA L7P 1A1 AUSTRALIA
905/335-2255 1-800-331-627
EMERGENCY NUMBER (SPILLS, EXPOSURES): 301/431-8585 (24 HOUR)
800/451-8346 (24 HOUR)
NON-EMERGENCY INFORMATION: 800/955-6288
Product Name: E-PAGE buffer #1, 4X
Stock Number: EPBUF01
NOTE: If this product is a kit or is supplied with more than one material,
please refer to the MSDS for each component for hazard information.
Product Use:
These products are for laboratory research use only and are not intended for
human or animal diagnostics, therapeutic, or other clinical uses, unless
otherwise stated.
Synonyms:
Not available.
______________________________________________________________________________
2. COMPOSITION, INFORMATION ON INGREDIENTS
______________________________________________________________________________
The following list shows components of this product classified as hazardous
based on physical properties and health effects:
Component CAS No. Percent
LITHIUM DODECYL SULFATE 2044-56-6 7 - 13
LTIMSDS2
______________________________________________________________________________
MATERIAL SAFETY DATA SHEET
__________________________ Page 2 of 8
Revised 6/09/04
E-PAGE BUFFER #1, 4X Replaces 4/01/04
INVITROGEN CORPORATION Printed 8/31/04
MSDS ID: EPBUF01
______________________________________________________________________________
______________________________________________________________________________
3. HAZARDS IDENTIFICATION
______________________________________________________________________________
***************************** EMERGENCY OVERVIEW ****************************
Warning!
Irritant.
Harmful if swallowed.
*****************************************************************************
Potential Health Effects:
Eye:
Can cause minor irritation, tearing and reddening.
Skin:
Can cause moderate skin irritation, defatting, and dermatitis. Not likely
to cause permanent damage.
Inhalation:
Can cause minor respiratory irritation, dizziness, weakness, fatigue,
nausea, and headache.
No toxicity expected from inhalation.
Ingestion:
Mildly irritating to mouth, throat, and stomach. Can cause abdominal
discomfort.
Ingestion of this product may result in central nervous system effects
including headache, sleepiness, dizziness, slurred speech and blurred vision.
Harmful if swallowed. May cause systemic poisoning.
Chronic:
No data on cancer.
______________________________________________________________________________
4. FIRST AID MEASURES
______________________________________________________________________________
Eye:
Flush eyes with plenty of water for at least 20 minutes retracting eyelids
often. Tilt the head to prevent chemical from transferring to the
uncontaminated eye. Get immediate medical attention.
Skin:
Wash with soap and water. Remove contaminated clothing and launder. Get
medical attention if irritation develops or persists.
Inhalation:
Remove to fresh air. If breathing is difficult, have a trained individual
administer oxygen. If not breathing, give artificial respiration and have
a trained individual administer oxygen. Get medical attention immediately.
Ingestion:
Do not induce vomiting and seek medical attention immediately. Drink two
LTIMSDS2
______________________________________________________________________________
MATERIAL SAFETY DATA SHEET
__________________________ Page 3 of 8
Revised 6/09/04
E-PAGE BUFFER #1, 4X Replaces 4/01/04
INVITROGEN CORPORATION Printed 8/31/04
MSDS ID: EPBUF01
______________________________________________________________________________
______________________________________________________________________________
4. FIRST AID MEASURES (CONT.)
______________________________________________________________________________
glasses of water or milk to dilute. Provide medical care provider with
this MSDS.
Note To Physician:
Treat symptomatically.
______________________________________________________________________________
5. FIRE FIGHTING MEASURES
______________________________________________________________________________
Flashpoint Deg C:
Not available.
Upper Flammable Limit %:
Not available.
Lower Flammable Limit %:
Not available.
Autoignition Temperature Deg C:
Not available.
Extinguishing Media:
Use alcohol resistant foam, carbon dioxide, or dry chemical when fighting
fires. Water or foam may cause frothing if liquid is burning but it still
may be a useful extinguishing agent if carefully applied to the surface of
the fire. Do Not direct a stream of water into the hot burning liquid.
Use water spray/fog for cooling.
Firefighting Techniques/Equipment:
Do not enter fire area without proper protection including self-contained
breathing apparatus and full protective equipment. Fight fire from a safe
distance and a protected location due to the potential of hazardous vapors
and decomposition products.
Hazardous Combustion Products:
Includes carbon dioxide, carbon monoxide, dense smoke.
______________________________________________________________________________
6. ACCIDENTAL RELEASE MEASURES
______________________________________________________________________________
Accidental releases may be subject to special reporting requirements and other
regulatory mandates. Refer to Section 8 for personal protection equipment
recommendations.
Spill Cleanup:
Exposure to the spilled material may be irritating or harmful. Follow
personal protective equipment recommendations found in Section VIII of
this MSDS. Additional precautions may be necessary based on special
circumstances created by the spill including; the material spilled, the
quantity of the spill, the area in which the spill occurred. Also consider
LTIMSDS2
______________________________________________________________________________
MATERIAL SAFETY DATA SHEET
__________________________ Page 4 of 8
Revised 6/09/04
E-PAGE BUFFER #1, 4X Replaces 4/01/04
INVITROGEN CORPORATION Printed 8/31/04
MSDS ID: EPBUF01
______________________________________________________________________________
______________________________________________________________________________
6. ACCIDENTAL RELEASE MEASURES (CONT.)
______________________________________________________________________________
the expertise of employees in the area responding to the spill.
Ventilate the contaminated area.
Prevent the spread of any spill to minimize harm to human health and the
environment if safe to do so. Wear complete and proper personal protective
equipment following the recommendation of Section VIII at a minimum. Dike
with suitable absorbent material like granulated clay. Gather and store in
a sealed container pending a waste disposal evaluation.
______________________________________________________________________________
7. HANDLING AND STORAGE
______________________________________________________________________________
Storage of some materials is regulated by federal, state, and/or local laws.
Storage Pressure:
Ambient
Handling Procedures:
Harmful or irritating material. Avoid contacting and avoid breathing the
material. Use only in a well ventilated area.
Keep closed or covered when not in use.
Storage Procedures:
Store in a cool dry ventilated location. Isolate from incompatible
materials and conditions. Keep container(s) closed.
Suitable for most general chemical storage areas.
______________________________________________________________________________
8. EXPOSURE CONTROLS, PERSONAL PROTECTION
______________________________________________________________________________
Exposure Limits:
OSHA PEL AGCIH TWA
Component (ppm) (ppm)
LITHIUM DODECYL SULFATE Not established. Not established.
Engineering Controls:
Local exhaust ventilation or other engineering controls are normally
required when handling or using this product to avoid overexposure.
Personal Protective Equipment:
Eye:
An eye wash station must be available where this product is used.
Wear chemically resistant safety glasses with side shields when handling
this product. Wear additional eye protection such as chemical splash
goggles and/or face shield when the possibility exists for eye contact
with splashing or spraying liquid, or airborne material. Do not wear
contact lenses. Have an eye wash station available.
LTIMSDS2
______________________________________________________________________________
MATERIAL SAFETY DATA SHEET
__________________________ Page 5 of 8
Revised 6/09/04
E-PAGE BUFFER #1, 4X Replaces 4/01/04
INVITROGEN CORPORATION Printed 8/31/04
MSDS ID: EPBUF01
______________________________________________________________________________
______________________________________________________________________________
8. EXPOSURE CONTROLS, PERSONAL PROTECTION (CONT.)
______________________________________________________________________________
Skin:
Avoid skin contact by wearing chemically resistant gloves, an apron and
other protective equipment depending upon conditions of use. Inspect
gloves for chemical break-through and replace at regular intervals. Clean
protective equipment regularly. Wash hands and other exposed areas with
mild soap and water before eating, drinking, and when leaving work.
Have a safety shower available.
Respiratory:
A respiratory protection program that meets OSHA's 29 CFR 1910.134 and
ANSI Z88.2 requirements must be followed whenever workplace conditions
warrant a respirator's use.
______________________________________________________________________________
9. PHYSICAL AND CHEMICAL PROPERTIES
______________________________________________________________________________
Appearance/physical state: Liquid solution / suspension
Odor: No odor.
Not established.
Not established.
Not established.
Not established.
Not established.
Not established.
Specific Gravity/Density: 1.00
Octanol/water Partition Coeff: Not established.
Volatiles: Not established.
Evaporation Rate: 0.3 (BUTYL ACETATE = 1.0)
Viscosity: 0.98 cp at 20掳C
______________________________________________________________________________
10. STABILITY AND REACTIVITY
______________________________________________________________________________
Stability:
Stable under normal conditions.
Conditions to Avoid:
Strong oxidizing agents.
Hazardous Decomposition Products:
Carbon monoxide. Carbon dioxide. Sulfur containing gases.
Hazardous Polymerization:
Hazardous polymerization will not occur.
LTIMSDS2
______________________________________________________________________________
MATERIAL SAFETY DATA SHEET
__________________________ Page 6 of 8
Revised 6/09/04
E-PAGE BUFFER #1, 4X Replaces 4/01/04
INVITROGEN CORPORATION Printed 8/31/04
MSDS ID: EPBUF01
______________________________________________________________________________
______________________________________________________________________________
11. TOXICOLOGICAL INFORMATION
______________________________________________________________________________
Acute Toxicity:
Dermal/Skin:
Not determined.
Inhalation/Respiratory:
Not determined.
Oral/Ingestion:
Not determined.
Target Organs: Kidneys. Lungs. Nervous System.
Carcinogenicity:
NTP:
Not tested.
IARC:
Not listed.
OSHA:
Not regulated.
Other Toxicological Information
______________________________________________________________________________
12. Ecological Information
______________________________________________________________________________
Ecotoxicological Information: No ecological information available.
Environmental Fate (Degradation, Transformation, and Persistence):
Bioconcentration is not expected to occur.
______________________________________________________________________________
13. DISPOSAL CONSIDERATIONS
______________________________________________________________________________
Regulatory Information:
Not applicable.
Disposal Method:
Clean up and dispose of waste in accordance with all federal, state, and
local environmental regulations.
Dispose of by incineration following Federal, State, Local, or Provincial
regulations.
LTIMSDS2
______________________________________________________________________________
MATERIAL SAFETY DATA SHEET
__________________________ Page 7 of 8
Revised 6/09/04
E-PAGE BUFFER #1, 4X Replaces 4/01/04
INVITROGEN CORPORATION Printed 8/31/04
MSDS ID: EPBUF01
______________________________________________________________________________
______________________________________________________________________________
14. TRANSPORT INFORMATION
______________________________________________________________________________
Proper Shipping Name: Not regulated.
Subsidiary Hazards:
______________________________________________________________________________
15. REGULATORY INFORMATION
______________________________________________________________________________
UNITED STATES:
TSCA:
This product is solely for research and development purposes only and may not
be used, processed or distributed for a commercial purpose. It may only be
handled by technically qualified individuals.
Materials used in manufacturing processes which are subject to compliance with
the Federal Food Drug and Cosmetic Act (FDA) are not subject to the Toxic
Substance Control Act (TSCA). The TSCA research use only restriction does not
apply to FDA regulated manufacturing processes nor the resulting product
per 15 U.S.C. 2602(2).
Prop 65 Listed Chemicals: PROP 65 PERCENT
No Prop 65 Chemicals.
No 313 Chemicals
CANADA:
DSL/NDSL:
Not determined.
COMPONENT WHMIS Classification
LITHIUM DODECYL SULFATE Not classified as hazardous.
EUROPEAN UNION:
PRODUCT RISK PHRASES:
None assigned.
PRODUCT SAFETY PHRASES:
Not applicable.
PRODUCT CLASSIFICATION:
Xi
EINECS
Component Number
LITHIUM DODECYL SULFATE 218-058-2
LTIMSDS2
______________________________________________________________________________
MATERIAL SAFETY DATA SHEET
__________________________ Page 8 of 8
Revised 6/09/04
E-PAGE BUFFER #1, 4X Replaces 4/01/04
INVITROGEN CORPORATION Printed 8/31/04
MSDS ID: EPBUF01
______________________________________________________________________________
______________________________________________________________________________
16. OTHER INFORMATION
______________________________________________________________________________
HMIS Rating 0-4:
FIRE: Not determined.
HEALTH: Not determined.
REACTIVITY: Not determined.
Abbreviations
N/A - Data is not applicable or not available
SARA - Superfund and Reauthorization Act
HMIS - Hazard Material Information System
WHMIS - Workplace Hazard Materials Information System
NTP - National Toxicology Program
OSHA - Occupational Health and Safety Administration
IARC - International Agency for Research on Cancer
PROP 65 - California Safe Drinking Water and
Toxic Enforcement Act of 1986
EINECS - European Inventory of Existing Commercial
Chemical Substances
The above information was acquired by diligent search and/or investigation
and the recommendations are based on prudent application of professional
judgment. The information shall not be taken as being all inclusive and is
to be used only as a guide. All materials and mixtures may present unknown
hazards and should be used with caution. Since Invitrogen Corporation cannot
control the actual methods, volumes, or conditions of use, the Company shall
not be held liable for any damages or losses resulting from the handling or
from contact with the product as described herein. THE INFORMATION IN THIS
MSDS DOES NOT CONSTITUTE A WARRANTY, EXPRESS OR IMPLIED, INCLUDING ANY
IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE.
|