AMERICAN INTERNATIONAL INDUSTRIES
2220 GASPAR AVENUE
LOS ANGELES, CA 90040
CHEM-TEL: (800) 255-3924
MATERIAL SAFETY DATA SHEET
PRODUCT NAME: EzFlow UV 30 DATE: 12/17/2003
FORMULA: 30-1327 REV. NEW
Section 1. Material Identification and Information
Hazardous Ingredients:
Component TOXICOLOGICAL DATA
CAS # %
Acrylic Polymer in Toluene None Established 60-100 OSHA PEL/TWA: 100ppm
ACGIH TLV/STEL: 75ppm
Toluene 108-88-3 30-60 OSHA PEL/TWA: 100ppm
ACGIH TLV/STEL: 75ppm
Butyl Acetate 123-86-4 15-40 OSHA PEL/TWA: 150ppm
ACGIH TLV/STEL: 200ppm
Section 2. Physical / Chemical Characteristics
111oC
Boiling Point: Specific Gravity: Not Determined
22 mm Hg @ 20 oC (@ 25oC)
Vapor Pressure:
(mm Hg and Temperature) Viscosity: 2300-4300cps
Vapor Density: 3-4 times heavier than air Evaporation Rate: 1.9 (Toluene)
(Air = 1) (Butyl Acetate = 1)
Solubility in Water: Insoluble to Slightly Soluble Water Reactive: N/A
Appearance: Clear Colorless Liquid pH: N/A
Odor: Sweet and Sour % Volatile: ~ 60%
Section 3. Fire and Explosion Hazard Data
7oC / 45oF
Flash Point:
407oC
Auto-Ignition Temperature:
Flammability Limits in Air % by Volume: LEL: 1.2%
UEL: 7.1%
Extinguisher Media: Carbon dioxide, dry chemical, alcohol foam, or water spray.
Fire Fighting Procedures: Wear self-contained breathing apparatus and full protective gear.
Remove all sources of ignition if it can be done safely. Move containers
from fire area if you can do so without risk. Cool containers exposed to
fire with water spray.
Eliminate sources of ignition. Above the flash point, vapor-air mixtures
Fire and Explosion Hazards
are explosive within the flammable limits. Sealed containers may
rupture when heated. Vapors can flow along surfaces to distant ignition
sources and flash back. Material creates a special hazard because it
floats on water.
Explosion Hazard: Fight fire from protected location.
Sensitive to Mechanical Impact: No
Sensitive to Static Discharge: Yes
Page 1 of 8
AMERICAN INTERNATIONAL INDUSTRIES
2220 GASPAR AVENUE
LOS ANGELES, CA 90040
CHEM-TEL: (800) 255-3924
MATERIAL SAFETY DATA SHEET
PRODUCT NAME: EzFlow UV 30 DATE: 12/17/2003
FORMULA: 30-1327 REV. NEW
Section 4. Reactivity Hazard Data
Unstable
Stability: Stable
Conditions to Avoid:
Heat, open flames, sparks, static electricity, sunlight, or other sources of ignition.
Incompatibility (Materials to Avoid):
Strong oxidizing agents.
Hazardous Decomposition:
Mainly oxides of carbon when burned.
Hazardous Polymerization:
Will Not Occur
May Occur
Section 5. Health Hazard Data
POTENTIAL HEALTH EFFECTS, SIGNS and SYMPTOMS OF EXPOSURE:
Primary Routes of Entry:
Inhalation Eyes
Skin Absorption Ingestion
Carcinogen Listed In:
NTP OSHA
IARC Monograph Not Listed
Health Hazards:
For Acrylic Polymer in Toluene:
Acute: Eye Contact: Can cause severe irritation and corneal clouding
Ingestion: Can cause gastrointestinal irritation, nausea, vomiting, diarrhea.
Inhalation: Can cause irritation of the nose, throat and lungs; headache; dizziness;
drowsiness; fatigue; loss of coordination; unconsciousness.
Skin Contact: Moderate irritant. Can cause defatting and drying of the skin which can
lead to irritation and dermatitis. Solvent may be absorbed through the
skin.
Chronic: Inhalation: High solvent vapor or mist concentrations can cause respiratory tract
irritation, liver, kidneys and cardiovascular system. May also cause
coma and/or death.
Aggravated Pre-Existing Conditions: Chronic respiratory problems such as asthma, emphysema or bronchitis.
May aggravate existing skin conditions.
For Toluene:
Acute: Eye Contact: Causes severe irritation with redness and pain.
Inhalation: May cause irritation of upper respiratory tract. Symptoms of over-
exposure may include fatigue, confusion, headache, dizziness and
drowsiness. Peculiar skin sensations (e.g. pins and needles) or
numbness may be produced. Very high concentrations may cause
unconsciousness and death.
Skin Contact: Causes irritation. May be absorbed through skin.
Page 2 of 8
AMERICAN INTERNATIONAL INDUSTRIES
2220 GASPAR AVENUE
LOS ANGELES, CA 90040
CHEM-TEL: (800) 255-3924
MATERIAL SAFETY DATA SHEET
PRODUCT NAME: EzFlow UV 30 DATE: 12/17/2003
FORMULA: 30-1327 REV. NEW
Ingestion: May cause abdominal spasms and other symptoms that parallel over-
exposure from inhalation. Aspiration into lungs can cause chemical
pneumonitis, which may be fatal.
Chronic: Chronic Poisoning: Anemia, decreased blood cell count and bone marrow hyperplasia.
Liver and kidney damage may occur. Exposure may effect the
developing fetus.
Skin Contact: Repeated or prolonged contact has a defatting action, causing drying,
redness and dermatitis.
Aggravated Pre-Existing Conditions: Persons with pre-existing skin disorders or impaired liver or kidney
function may be more susceptible to the effects. Alcoholic beverage
consumption can enhance the toxic effects.
Note to Physician: Acute massive exposure to toluene can cause transient hematuria and
albuminuria. Cardiac arrhythmias can occur after massive inhalation.
For Butyl Acetate:
Acute: Eye Contact: Vapor and liquid causes irritation.
Inhalation: May cause drowsiness and irritation of eye or respiratory tract.
Skin Contact: Prolonged or repeated contact may cause drying, cracking, or irritation.
Chronic: Overexposure may cause anemia with leukotosis (transient increase in
the white blood cell count) and damage to the liver and kidneys.
Inhalation: High concentrations may cause lung damage. Exposure to high
concentrations have a narcotic effect and may cause a stupor and
headaches. May cause liver and kidney damage.
Skin Contact: Repeated or prolonged contact has a defatting action, causing drying,
redness and dermatitis.
Emergency First Aid Procedures:
Eye Contact: If easy to do remove contact lenses. Flush with water for 15 minutes,
including under eyelids. Seek medical attention. In case of irritation
from airborne exposure, move to fresh air.
Skin Contact: Immediately wash with lots of soap and water. Seek immediate medical
attention.
Inhalation: Remove to fresh air, assure victim is breathing. Seek immediate
medical attention. If not breathing, administer CPR, if breathing difficult,
give oxygen.
Ingestion: If conscious and alert, give 2-3 glasses of water. Do not induce
vomiting. Material may enter lungs and cause severe damage. Seek
immediate medical attention.
Clothing: Remove contaminated clothing and shoes. Heavily contaminate
clothing should be discarded. Wash/clean thoroughly before reuse.
Treatment: Treat symptoms conventially after thorough decontamination.
Consideration should be given to possibly that overexposure to the
solvent has occurred.
Page 3 of 8
AMERICAN INTERNATIONAL INDUSTRIES
2220 GASPAR AVENUE
LOS ANGELES, CA 90040
CHEM-TEL: (800) 255-3924
MATERIAL SAFETY DATA SHEET
PRODUCT NAME: EzFlow UV 30 DATE: 12/17/2003
FORMULA: 30-1327 REV. NEW
Section 6. Control and Protective Measures
Ventilation: Use good, local explosion-proof ventilation with a minimum capture velocity of 100ft.min
(30,/min) at point of monomer release. Refer to Industrial Ventilation: A Manual of
Recommended Practice published by the American Conference of Governmental Industrial
Hygienists. Local exhaust ventilation is preferred since it prevents contamination dispersion into
the work area by controlling it as its source.
Respiratory Protection:
Use self-contained breathing apparatus when needed.
Eye Protection:
Safety glasses or chemical splash goggles.
Protective Gloves:
Impervious, nitrile.
Other Protective Equipment:
Provide eyewash, safety shower and impervious clothing. Protective creams should not be
used for protection, but may be used for ease of clean-up.
Industrial Hygiene Practices:
Wash face and hands thoroughly with soap and water after use and before eating, drinking,
smoking or applying cosmetics.
Section 7. Precautions for Safe Handling and Use / Leak Procedures
Steps to be Taken if Material is Spilled or Released:
Evacuate area and eliminate all possible sources of ignition. Use self-contained breathing
apparatus and protective clothing. Dike and absorb with inert materials ( sand, soda, ash,
vermiculite, etc.) and then transfer to proper containers for disposal, using non-sparking tools.
Contaminated monomer ma be unstable, add inhibitor to prevent polymerization. Keep spills
out of sewers and open bodies of water. Remove saturated clothing and wash affected areas
with soap and water.
Waste Disposal Methods: y
liquid and diking material after addition of excess inhibitor, in accordance with Federal, State,
and Local regulations.
Handling:
Use in well ventilated areas. Avoid contact with skin, eyes, and clothing. Observe precautions
found on the label. Close container after each use. Ground all metal containers when
transferring. Use explosion-proof equipment. Use good personal hygiene and housekeeping.
Recommended Minimum Storage Temperature: -18 oC, 0oF.
Storage:
o o
Recommended Maximum Storage Temperature: 49 C, 120 F.
Store in a well ventilated area, away from heat, sparks, flame, direct sunlight or other sources of
ignition. Keep away for incompatible materials.
Page 4 of 8
AMERICAN INTERNATIONAL INDUSTRIES
2220 GASPAR AVENUE
LOS ANGELES, CA 90040
CHEM-TEL: (800) 255-3924
MATERIAL SAFETY DATA SHEET
PRODUCT NAME: EzFlow UV 30 DATE: 12/17/2003
FORMULA: 30-1327 REV. NEW
Section 8. Toxicological Information
Target Organs: None listed
Sensitivity Data:
For Acrylic Polymer in Toluene:
None Listed.
For Toluene: Eye Human: 300ppm
Eye Rabbit: 870碌g. Mild.
Eye Rabbit: 2mg/24H. Severe
Eye Rabbit: 100mg/30s rinse. Mild.
Skin Rabbit: 435mg. Mild
For Butyl Acetate: Skin Rabbit: 500mg. Moderate
Eye Human: 300ppm
Eye Rabbit: 20mg open. Severe
Eye Rabbit: Moderate.
Skin Guinea Pig: Slight.
Skin Rabbit: 500mg/24H. Moderate.
Mutagenicity Data:
For Acrylic Polymer in Toluene:
None Listed.
5400 碌g/m3/16W
For Toluene: Inhalation Rat Cytogenetic Analysis:
Subcutaneous Rat Cytogenetic Analysis: 12gm/kg/12D
2400碌mol/tube
S. Cerevisiae Cytogenetic Analysis:
30碌mol/L
Liver Rat DNA Damage:
E. Coli Unscheduled DNA Synthesis: 1pph
Microorganisms Unscheduled DNA Synthesis: 1pph/15M
422碌g/kg/24H
Interperitoneal Mouse Micronucleus Test:
Oral Mouse Micronucleus Test: 200mg/kg
Inhalation Grasshopper Test Systems (Other): 562mg/L
Reproductive Toxicity Data:
For Acrylic Polymer in Toluene:
None Listed.
For Toluene: Has been demonstrated to be embryofetotoxic and teratogenic in laboratory animals.
3
TCLo: 500mg/m /24, 6-13D preg.
Inhalation Mouse
TCLo: 1000ppm/6H, 2-17D preg.
Inhalation Mouse
TCLo: 400ppm/7H, 7-16D preg.
Inhalation Mouse
TCLo: 200ppm/7H, 7-16D preg.
Inhalation Mouse
3
TCLo: 1500mg/m /24H, 1-8D preg.
Inhalation Rat
TCLo: 9g/kg, 6-15D preg.
Oral Mouse
TCLo: 15g/kg, 6-15D preg.
Oral Mouse
TCLo: 30g/kg, 6-15D preg.
Oral Mouse
TCLo: 1500ppm/7H, 7-16D preg.
For Butyl Acetate: Inhalation Rat
Page 5 of 8
AMERICAN INTERNATIONAL INDUSTRIES
2220 GASPAR AVENUE
LOS ANGELES, CA 90040
CHEM-TEL: (800) 255-3924
MATERIAL SAFETY DATA SHEET
PRODUCT NAME: EzFlow UV 30 DATE: 12/17/2003
FORMULA: 30-1327 REV. NEW
Toxicity Data:
For Acrylic Polymer in Toluene:
Not Listed.
LCLo:
For Toluene: Inhalation Guinea Pig 1600ppm
TCLo:
Inhalation Human 200ppm
TCLo:
Inhalation Man 100ppm
LCLo:
Inhalation Mouse 5320 ppm/8H
LCLo:
Inhalation Rat 4000ppm/4H
LD50:
Intraperitoneal Mouse 1126mg/kg
LDLo:
Intraperitoneal Rat 800mg/kg
LD50:
Intravenous Rat 1960mg/kg
LDLo:
Oral Human 50mg/kg
LD50:
Oral Rat 5000mg/kg
LDLo:
Subcutaneous Rat 920mg/kg
LD50:
Skin Rabbit 12124mg/kg
LD50:
Unreported Route Mouse 2000mg/kg
LD50:
Unreported Route Rat 6900mg/kg
3
68g/m /72H
LCLo:
For Butyl Acetate: Inhalation Cat
3
67g/m /4H
LCLo:
Inhalation Guinea Pig
LCLo:
Inhalation Human 7000ppm/13H
TCLo:
Inhalation Mouse 200ppm
3
6g/m /2H
LC50:
Inhalation Rat
LC50:
Inhalation Rat 2000ppm/4H
LC50:
Intramuscular Guinea Pig 1800ppm/6H
LDLo:
Intraperitonial Guinea Pig 2648mg/kg
LD50:
Intraperitoneal Mouse 1500mg/kg
LDLo:
Oral Guinea Pig 1230mg/kg
LD50:
Oral Mouse 4700mg/kg
LD50:
Oral Mouse 7060mg/kg
LD50:
Oral Rat 14g/kg
LD50:
Oral Rat 14130mg/kg
LD50:
Oral Rabbit 7400mg/kh
LD50:
Skin Guinea Pig 8770mg/kg
Section 9. Ecological Information
Aquatic Toxicity:
100mg/L/96H
LC50:
Bluegill Sunfish
For Butyl Acetate:
LC50:
Tidewater Silverside 185mg/L/96H
LC50:
Daphnia 44-205mg/L/96H
Ecotoxicity Data:
For Acrylic Polymer in Toluene: No Applicable Data
LC50:
Fish 10-100mg/L/96H
For Toluene
Page 6 of 8
AMERICAN INTERNATIONAL INDUSTRIES
2220 GASPAR AVENUE
LOS ANGELES, CA 90040
CHEM-TEL: (800) 255-3924
MATERIAL SAFETY DATA SHEET
PRODUCT NAME: EzFlow UV 30 DATE: 12/17/2003
FORMULA: 30-1327 REV. NEW
Environmental Fate:
When released into soil, may evaporate to moderate extent. When released into soil, expected
to leach into groundwater. When released into soil, may biodegrade to moderate extent. When
released into water, may evaporate to moderate extent. When released into water, may
biodegrade to moderate extent. When released into air, may moderately degraded by reaction
with photochemically produced hydroxyl radicals. When released to into air, expected to have a
half-life of less than 1 day. This material is not expected to significantly bioaccumulate.
Oxygen Demand Data:
For Butyl Acetate: BOD-5: 1020mg/g
BOD-20: 1450mg/g
ThOD: 2207mg/g
Section 10. Disposable Concentrations
Waste Disposal Method:
When discarded it is listed as hazardous waste by the EPA under RCRA as U220. Incinerate
liquid and diking material after addition of excess inhibitor, in accordance with Federal, State,
and Local regulations.
Disposal of Empty Containers:
Reuse of empty drums or containers is not recommended. Employees should be advised of the
potential hazards, due to residual flammable material, associated with empty containers. IT is
our policy to discourage the reuse of empty containers and to dispose of all empty containers
properly, in accordance with Federal, State, and Local regulations.
Section 11. Transport Information
DOT/ UN Shipping Name: FLAMMABLE LIQUID, NOS (Contains Toluene and Butyl Acetate)
DOT/UN Class: 3
NA/UN Number: UN1993
Packing Group: II
NAERG: 130
Label: Flammable Liquid
NMFC ITEM #: 60004, Declared Value must be filled in
Schedule B: 2902.20.0000
IMDG Class: 3.2
EmS: 7-Mar
CERCLA RQ: For Component: Toluene: 1000lbs.
Butyl Acetate: 5000lbs.
Page 7 of 8
AMERICAN INTERNATIONAL INDUSTRIES
2220 GASPAR AVENUE
LOS ANGELES, CA 90040
CHEM-TEL: (800) 255-3924
MATERIAL SAFETY DATA SHEET
PRODUCT NAME: EzFlow UV 30 DATE: 12/17/2003
FORMULA: 30-1327 REV. NEW
Section 12. Regulatory Information
Acrylic Polymer in Toluene Listing:
TSCA, EINECS, CERCLA, CA65
Toluene as a Component Listing:
TSCA, EINECS, CERCLA, SARA 313, CAA, RCRA (U220), CA65, FL, MA, MI, MN, NJ, PA,
WA
Butyl Acetate Listing:
TSCA, EINECS, SARA 313, MA, MI, NJ
TSCA: For use in FDA regulated products only.
Canadian WHMIS: This product has been classified in accordance with the hazardous criteria of the CPR and the
MSDS contains all the information required by the CPR.
F-Flammable
Warning Code:
R10-Flammable
Risk Statements:
R36/38-Irritating to eyes and
R43-May cause sensitization by skin contact
Safety Statements: S3-Keep in a cool place.
S7/8-Keep container tightly closed and dry.
S9-Keep container in a well ventilated place.
S15/16-Keep away from heat, sources of ignition - No smoking.
S20-When using do not eat or drink
S23-Do not breath away
S24/25-Avoid contact with skin and eyes
S29-Do not empty into drains
S37/39-Wear suitable gloves and eye/face protection.
Section 13. Other Information
Hazardous Material Identification System (HMIS) Rating:
Health: 3
Flammability: 3
Reactivity: 0
Personal Protective Equipment: Gloves and Safety Glasses or Chemical Splash Goggles
National Fire Protection Association (NFPA) Hazard Identification Rating:
Health: 3
Flammability: 3
Reactivity: 0
This product contains
Page 8 of 8
|