MATERIAL SAFETY DATA SHEET
Page: 1
DATE ISSUED: 8/08/2005
MSDS No: EZ
EZ Sticker Remover 鈥揚art No's 8-EZ, 128-EZ
1. CHEMICAL PRODUCT AND COMPANY IDENTIFICATION
Product Name: EZ Sticker Remover 鈥揚art No's 8-EZ, 128-EZ
POISIONS
24 HR. EMERGENCY
DISTRIBUTOR:
INFORMATION
NUMBERS:
The Blaster Group Pty Ltd
CENTRE
Unit 30, 8 Victoria Street
PHONE: 13 11 26
Castle Hill NSW 2154
Emergency Phone: 02 9894 7360
Customer Service: 02 9894 7360
2. COMPOSITION INFORMATION ON INGREDIENTS
64741-65-7
Mineral Spirits < 90
Isopropyl alcohol 67-63-0
< 10
HAZARDOUS COMPONENTS
EXPOSURE LIMITS
OSHA PEL ACGIH TLV
Mineral Spirits 100 ppm 100 ppm
Isopropyl alcohol 400 ppm
500 ppm
COMMENTS:
The criteria for listing components in this section are as follows: Carcinogens
are listed if present at 0.1% or greater
OSHA hazardous ingredients are listed if present at 1.0% or greater
Non-Hazardous ingredients may be listed if present at 5.0% or greater
3. HAZARDS IDENTIFICATION
POTENTIAL HEALTH EFFECTS
EYES:
Direct contact with eyes may cause irritation, redness, tearing
SKIN:
Repeated or prolonged contact with skin may produce irritation or dryness. May cause dermatitis or
aggravate an existing condition.
Page: 2
DATE ISSUED: 8/08/2005
MSDS No: EZ
EZ Sticker Remover 鈥揚art No's" 8-EZ, 128-EZ
INGESTION:
Product is an aspiration hazard. This material can enter lungs during swallowing or vomiting
and cause lung inflammation and damage. Can cause irritation to mouth, oesophagus, and
stomach.
INHALATION:
Tests have shown a negligible degree of toxicity by inhalation. May cause irritation to respiratory tract.
MEDICAL CONDITIONS AGGRAVATED:
May aggravate existing skin and respiratory disorders.
COMMENTS:
NOTICE -Reports have associated repeated and prolonged occupational overexposure to solvents with
permanent brain and nervous system damage. Intentional misuse by deliberately concentrating and inhaling
the contents may be harmful or fatal.
4. FIRST AID MEASURES
EYES:
Flush with plenty of clear water. Seek medical attention.
SKIN:
Remove contaminated clothing immediately. Wash skin with soap and water. If irritation develops, seek
medical attention
INGESTION:
Aspiration hazard: Do not induce vomiting or give anything by mouth because this material can enter the
lungs and cause severe lung damage. If the victim is drowsy or unconscious, place on left side with the
head down. If possible do not leave victim unattended. Seek medical attention.
INHALATION:
If irritation does occur, remove to fresh air. If symptoms persist seek medical attention.
5. FIRE FIGHTING MEASURES
Flashpoint and Method: -52掳C TAG CC
Autoignition Temperature: ~360掳C
GENERAL HAZARD:
This material can be ignited by heat, sparks, flames, or other sources of ignition (static electricity.) Vapours are
heavier than air and will collect in low areas (sewers) or travel considerable distances to a source of ignition. If
containers are not cooled in a fire, they may ignite and explode.
Page: 3
DATE ISSUED: 8/08/2005
MSDS No: EZ
EZ Sticker Remover 鈥揚art No's 8-EZ, 128-EZ
EXTINGUISHING MEDIA:
Dry chemical, carbon dioxide, halon, or foam is recommended. Water spray may be used to cool
containers or structures. Halon may decompose into toxic materials and carbon dioxide will displace
oxygen. Use proper precautions when using these materials.
FIRE FIGHTING PROCEDURES:
Emergency responders in the danger area should wear bunker gear and self-contained breathing
apparatus for fires beyond the incipient stage. Wear other protective gear as conditions warrant. Stop
leaks, if it can be done with minimal risk. Water spray may be useful in dispersing vapours or cooling
equipment and containers. Material will float on water. Avoid spreading fire with water.
6. ACCIDENTAL RELEASE MEASURES
SMALL SPILL:
Absorb the liquid and scrub the area with detergent and water.
LARGE SPILL:
Avoid vapours and ignition sources. Use appropriate protective equipment. Stop and contain the
discharge if it can be done s afely. Keep out of drains and water ways. Handle only with trained personnel.
Notify authorities as necessary.
GENERAL PROCEDURES:
Dispose of liquid and absorbents in accordance with local, state, and federal law.
7. HANDLING AND STORAGE
GENERAL PROCEDURES:
Use in accordance with good industrial workplace practices. Open containers slowly to relieve pressure.
HANDLING:
Avoid unnecessary contact. Wash thoroughly after handling. Do not wear contaminated clothing or
shoes.
STORAGE:
Store in a dry place away from excessive heat. Store containers tightly closed.
8. EXPOSURE CONTROLS/PERSONAL PROTECTION
PERSONAL PROTECTION
EYES AND FACE:
Standard safety glasses with splash shields are adequate protection. Where excessive splashing is
possible, a face shield should be used.
Page: 4
DATE ISSUED: 8/08/2005
MSDS No: EZ
EZ Sticker Remover 鈥揚art No's 8-EZ,128-EZ
SKIN:
Excessive contact should be avoided. Neoprene gloves and aprons will provide adequate protection when
contact cannot be avoided.
RESPIRATORY:
Good general ventilation should be sufficient to control airborne levels. Maintain airborne concentrations
below the established exposure limits of ingredients in Section 2.
PROTECTIVE CLOTHING:
Chemical resistant aprons and boots are suggested when contact with material cannot be avoided.
Remove and wash any contaminated clothing immediately.
WORK HYGIENIC PRACTICES:
Wash thoroughly after handling.
OTHER USE PRECAUTIONS:
Eye wash stations and emergency showers should be available.
COMMENTS:
The BLASTER CHEMICAL COMPANIES takes no responsibility for determining what measures are
required for personal protection in any specific application. The information provided should be used with
discretion.
9. PHYSICAL AND CHEMICAL PROPERTIES
Physical State: Liquid
Odour: Moderate aliphatic.
Appearance: Transparent
Colour: Clear
Percent Volatile: 96
Vapour Pressure: -1.2 mmHg
Vapour Density: -5.2 (Air = 1)
Boiling Point: 174 to 210掳C
Solubility in Water: Slight
Evaporation Rate: -0.17 (n-Butyl Acetate=1)
Specific Gravity: -0.759
Viscosity: -1.96 CST
10. STABILITY AND REACTIVITY
STABLE: YES
HAZARDOUS POLYMERIZATION: NO
Page: 5
DATE ISSUED: 8/08/2005
MSDS No: EZ
~ Sticker Remover -Part No's 8-EZ, 128-EZ
CONDITIONS TO AVOID:
Avoid excessive heat, sources of ignition, and excessive water.
STABILITY:
Stable under normal conditions of storage and handling. Flammable liquid and vapour. Vapours can
cause flash fire.
POLYMERIZATION:
Will not occur.
HAZARDOUS DECOMPOSITION:
Carbon monoxide, carbon dioxide, and various hydrocarbons.
INCOMPATIBLE MATERIALS:
Avoid contact with strong oxidizing agents and strong reducing agents (strong acids or bases.) Avoid
mixture with water.
11 TOXICOLOGICAL INFORMATION
COMMENTS:
Toxicological information on this product as a mixture has yet to be determined. See section 15 for
reportable ingredients.
12. ECOLOGICAL INFORMATION
ENVIRONMENTAL DATA:
No data available.
ECOTOXICOLOGICAL INFORMATION:
No data available.
13. DISPOSAL CONSIDERATIONS
DISPOSAL METHOD:
Used or unused product should be disposed of in accordance with local, state, and federal regulations.
EMPTY CONTAINER:
Empty containers will contain residual product and should be handled in the same manner as
the product. Containers should be returned to a reputable container reconditioner.
Page: 6
DATE ISSUED: 8/08/2005
MSDS No: EZ
EZ Sticker Remover -Part No鈥檚 8-EZ, 128-EZ
14. TRANSPORT INFORMATION
DOT (DEPARTMENT OF TRANSPORTATION)
Proper Shipping Name: Liquids, Flammable
Class: 3
UN Number: 1993
15. REGULATORY INFORMATION
UNITED STATES
SARA TITLE III (SUPERFUND AMENDMENTS AND REAUTHORIZATION ACT) Title III
Notes: There are no SARA 313 reportable materials in this product.
CERCLA (COMPREHENSIVE RESPONSE, COMPENSATION, AND LIABILITY ACT)
CERCLA RQ: This product has no CERCLA Reportable Quantity. However, release into a waterway may
require reporting to the National Response Centre.
TSCA (TOXIC SUBSTANCE CONTROL ACT)
TSCA Regulatory: This product complies with all TSCA Inventory requirements.
16. OTHER INFORMATION
Approval date: 03/14/2001
REVISION SUMMARY
New MSDS
NFPA CODES
Reactivity: 0
Fire: 1 Health: 2
HMIS CODES
Fire: 1 Health: 2 Reactivity: 0 Protection: X
MANUFACTURER DISCLAIMER:
To the best of our knowledge, the information contained herein is accurate. However, neither The Blas ter
Chemical Companies nor any of its subsidiaries assumes any liability whatsoever for the accuracy or
completeness of the information contained herein. Final determination of suitability of any material is the
sole responsibility of the user. All materials may present unknown hazards and should be used with
caution. Although certain hazards are described herein, we cannot guarantee that these are the only
hazards which exist.
|