MATERIAL SAFETY DATA SHEET
ROCKTUFF
Health Information Personal Protection
Classified As Hazardous Material
According To The Criteria Of The use of solvent resistant gloves,
Engineering Controls
Worksafe Australia coveralls and goggles (against
Follow normal good industrial hygiene
splashes) are recommended.
and chemical precautions, particularly
Identification: Rocktuff
If spraying the use of suitable breathing
in respect of flammability.
mask is recommended. If spraying in
Use in ventilated areas and provide
Other Name: Duram Rocktuff
confined areas self contained breathing
flame proof artificial ventilation if
Liquid moisture
apparatus is recommended.
required to maintain concentrations
curing polyurethane
Keep flame, sparks and sources of
anti-slip coating. below Xylene Exposure Standard of
ignition away from uncured product.
350g/m3(TWA) 655 mg/m3 (STEL) or
Vapours may collect in low-lying areas.
UN Number: 1263 100ppm.
Ensure ventilation, either natural or
DG Class: NA Keep sparks and ignition sources
artificial, is present to disperse
Hazchem Code: 3[Y] away from product and application
vapours.
Poison Schedule: 6
area during application, as product is
Packing Group 3 (Steel Drums)
flammable.
Safe Handling
Use: Anti-slip protective
Information
Health Effects
coating.
Storage/Handling: Store away from
Advice To Doctor:
flame and ignition sources. Keep cool,
Physical Description/ Treat symptomatically.
dry and away from direct sunlight.
Swallowed: Ingestion could cause
Properties/Appearance Spills: Remove sources of ignition.
irritation and burning sensation.
Appearance: Coloured Prevent spills from entering drains
Eye: Irritation and burning. Long-term
viscous liquid and waterways. Absorb with sand
exposure can cause damage. Grit can
incorporating or oil absorbing material. Discard to
scratch eyes.
aggregate.
suitable landfill in accordance with
Skin: Irritation, burning sensation.
Boiling Point: Approx 300潞C.
local regulation. Product will solidify
Solvent can dry skin. Long term can
Vapour Pressure: Approx 6.00
after contact with water or atmospheric
(Xylene). lead to skin cracking.
moisture.
Percent Volatile: +- 40%. Inhaled: Irritation with asthma like
Disposal: Shovel into drums,
Specific Gravity: +- 1.1. symptoms. It is unlikely that product
incinerate or land tip in accordance
Flash Point would be inhaled due to its viscosity. with local regulation.
[Closed Cup]: 28潞C (Xylene) Inhaled matter is likely to be Xylene. Fire/Explosion: Product contains
[Open Cup]: N/A
Xylene.
Flammability Lmt.: 1.1 鈥? 7.0%
First Aid Containers should be kept cool with
(Xylene)
Swallowed: Do not induce vomiting. water spray to prevent pressure build
Solubility In Water: Insoluble.
Give milk or water to drink. Seek urgent up. Burning product may product dense
Ingredients medical advice. irritating smoke. Heat may cause cans
Eye: Flush eye with copious amounts
Chemical CAS No. Proportion to rupture.
Urethane of clean water lifting lid to ensure Ingress of moisture will cause product
Polymer Not Known 30-60% to begin curing releasing CO2 and may
product is flushed from under the lid.
result in an increase in the pressure in
Get medical attention.
Inert Fillers Not Known 10-30% the containers.
Skin: Remove contaminated clothing.
Wipe product off skin. Wash skin with
Inert
Contact
soap and water. Apply moisturising
Aggregates Not Known 10-30%
cream. Duram Industries Pty Ltd
Inhaled: Remove person to fresh Australia: Tel: 02 9624-4077
Xylene 1330-20-7 10-50%
air. If breathing stops apply artificial New Zealand: (09)527-0551
respiration. Seek urgent medical
Minor
Ingredients Not Known <5% attention. October 04
IMPORTANT
The product information contained in this data sheet is given in good faith based upon our knowledge and current information and does not imply any warranty.
The information contained herein is provided on the basis that the product is applied in a proper manner strictly in accordance with instructions onto correctly prepared surfaces which shall remain
sound, stable and free of cracking or movement. Instruction application deviation may diminish or negate the performance of the product. Under no circumstances will the Company be liable for any
loss, consequential or otherwise, arising from the use of the product. We reserve the right to amend specification and application techniques without prior notice.
DURAM INDUSTRIES (PTY) LTD ACN 002 968 809 ABN 77 002 968 809
The Ultimate in Waterproofing & Protective Coating Technology
NEW SOUTH WALES: 51 Prince William Drive, Seven Hills, NSW 2147 Tel: (02) 9624 4077 Fax: (02) 9624 4079
WESTERN AUSTRALIA: 49 Banksia Road, Welshpool, WA 6106 Tel: (08) 9350 6565 Fax: (08) 9356 7575
QUEENSLAND: 775 Kingsford Smith Drive, Eagle Farm QLD 4009 Tel: (07) 3868 4888 Fax: (07) 3868 4390
NEW ZEALAND: Unit 3, 65 Elizabeth Knox Place, Mount Wellington, Auckland Tel: (09) 527 0551 Fax: (09) 527 0552
|