Product Name: General Purpose Viscosity
Standard 鈥? N.8
Revision Date: March 26, 2007
Page 1 of 10
MSDS ref CII07-008
MATERIAL SAFETY DATA SHEET
SECTION 1 PRODUCT AND COMPANY IDENTIFICATION
PRODUCT
General Purpose Viscosity Standard 鈥? N.8
Product name:
Product description: Petroleum hydrocarbon liquid; mixed xylenes
Product code: 9727-C15
Intended use: Low viscosity calibration standard
COMPANY IDENTIFICATION
Supplier: Cannon Instrument Company
2139 High Tech Road
State College, Pennsylvania 16803
Product Technical Information: (814) 353-8000
Product MSDS Information: (814) 353-8000
EMERGENCY TELEPHONE NUMBER:
24-Hour Transportation Emergency: (800) 255-3924 Domestic CHEM-TEL Inc.
24-Hour Health Emergency: +1 (813) 248-0585 Overseas CHEM-TEL Inc. (please call collect)
SECTION 2 COMPOSITION/INFORMATION ON INGREDIENTS
Reportable Hazardous Substance(s) or Complex Substance(s)
Name CAS# Concentration* Hazard/ basis
m-xylene 108-38-3. 40-65%
flammable, eye irritant,
o-xylene 95-47-6 15-20%
OSHA PEL, ACGIH TLV
p-xylene 106-42-3 <20%
Ethyl benzene 100-41-4 15-25% flammable, possible carcinogen
SECTION 3 HAZARD IDENTIFICATION
This material is considered hazardous according to regulatory guidelines (See Section 15).
EMERGENCY OVERVIEW:
Danger: Harmful or fatal if swallowed. Vapor harmful. Affects central nervous system. Causes severe eye
irritation. Causes irritation to skin and respiratory tract. May be harmful if absorbed through the skin. Chronic
exposure can cause adverse liver, kidney and blood effects. Flammable liquid and vapor
POTENTIAL PHYSICAL/CHEMICAL EFFECTS:
鈥? High hazard. Liquids can release vapors that can readily form flammable mixtures at temperatures at or
above the flash point.
This information relates only to the specific material designated and may not be valid for such material used in combination with any other materials or in any process. The information
and recommendations contained herein is compiled from suppliers鈥? MSDS and are accurate and reliable to the best of Cannon Instrument Company鈥檚 knowledge and belief as of the
indicated revision date. No representation, warranty or guarantee, however, is made with regards to accuracy, reliability or completeness. Conditions of use of the material are under
the control of the user; therefore, it is the user's responsibility to satisfy himself as to the suitability and completeness of such information for his own particular use.
Product Name: General Purpose Viscosity
Standard 鈥? N.8
Revision Date: March 26, 2007
Page 2 of 10
MSDS ref CII07-008
鈥? Static Discharge. Product can accumulate static charges which can cause an incendiary electrical
discharge.
POTENTIAL HEALTH EFFECTS:
EYE CONTACT: Irritating, but vapor does not injure eye tissue. Splashes may cause severe
irritation 鈥? possible corneal burns and eye damage
SKIN CONTACT: Frequent or prolonged contact may irritate. Skin contact may aggravate an
existing dermatitis condition.
INHALATION: High vapor/aerosol concentrations are irritating to the eyes and the respiratory
tract, and may cause headaches, dizziness, anesthesia, drowsiness,
unconsciousness, and other central nervous system effects, including death. High
vapor concentrations are anesthetic and central nervous system depressants
INGESTION: Small amounts of this product aspirated into the respiratory system during
ingestion or vomiting may cause mild to severe pulmonary injury, possibly
progressing to death.
CHRONIC EFFECTS: Chronic exposure can cause headache, loss of appetite, nervousness and pale
skin. Repeated or prolonged skin contact may cause a skin rash.
This product contains ethyl benzene. The International Agency for Research on
Cancer (IARC) has evaluated ethyl benzene and classified it as a possible human
carcinogen (group 2B) based on sufficient evidence for carcinogenicity in
experimental animals, but inadequate evidence for cancer in exposed humans.
NFPA HAZARD ID: Health: 2 Flammability: 3 Reactivity: 1
(National Fire Protection Association)
NOTE: This material should not be used for any other purpose than the intended use in Section 1 without expert
advice
SECTION 4 FIRST AID MEASURES
INHALATION Using proper respiratory protection, immediately remove the affected victim from
exposure. Administer artificial respiration if breathing is stopped. Keep at rest. Call for
prompt medical attention.
SKIN CONTACT Immediately flush with large amounts of water; use soap if available. Remove
contaminated clothing, including shoes, after flushing has begun. If irritation persists,
get medical attention.
EYE CONTACT Flush eyes with large amounts of water until irritation subsides. If irritation persists, get
medical attention.
INGESTION Aspiration hazard. If swallowed, DO NOT induce vomiting. Keep at rest. Get prompt
medical attention.
NOTE TO PHYSICIAN
Treat according to symptoms. However, be advised that small amounts of this product aspirated into the
respiratory system during ingestion or vomiting may cause mild to severe pulmonary injury (chemical
pneumonitis), possibly progressing to death.
PRE-EXISTING MEDICAL CONDITIONS WHICH MAY BE AGGRAVATED BY EXPOSURE
This information relates only to the specific material designated and may not be valid for such material used in combination with any other materials or in any process. The information
and recommendations contained herein is compiled from suppliers鈥? MSDS and are accurate and reliable to the best of Cannon Instrument Company鈥檚 knowledge and belief as of the
indicated revision date. No representation, warranty or guarantee, however, is made with regards to accuracy, reliability or completeness. Conditions of use of the material are under
the control of the user; therefore, it is the user's responsibility to satisfy himself as to the suitability and completeness of such information for his own particular use.
Product Name: General Purpose Viscosity
Standard 鈥? N.8
Revision Date: March 26, 2007
Page 3 of 10
MSDS ref CII07-008
Persons with pre-existing skin disorders or eye problems, or impaired liver, kidney blood or respiratory
function may be more susceptible to the effects of this substance
SECTION 5 FIRE-FIGHTING MEASURES
EXTINGUISHING MEDIA
Appropriate extinguishing media: Use foam or dry chemical to extinguish fire, Use water spray to cool
fire exposed surfaces and to protect personnel.
Inappropriate extinguishing media: Avoid spraying water directly into storage containers due to danger
of boilover.
FIRE FIGHTING
Shut off "fuel" to fire. If a leak or spill has not ignited, use water spray to disperse the vapors.
Use water spray to cool fire exposed surfaces and to protect personnel. Respiratory and eye protection
required for fire fighting personnel. This liquid is volatile and gives off invisible vapors. Either the liquid or
vapor may settle in low areas or travel some distance along the ground or surface to ignition sources
where they may ignite or explode.
UNUSUAL FIRE HAZARDS:
Typical for flammable hydrocarbon liquids
HAZARDOUS COMBUSTION PRODUCTS:
Fumes, smoke, carbon dioxide and carbon monoxide.
FLASH POINT: 29oC (84oF). CC
FLAMMABLE LIMITS (in air % by volume): LEL: 1.0 UEL: 7.0
AUTOIGNITION TEMP.: 464oC (867oF). Approximate
GENERAL HAZARD
Flammable Liquid, can release vapors that form flammable mixtures at temperatures at or above the
flashpoint. Toxic gases will form upon combustion. Material can accumulate static charges which can
cause an incendiary electrical discharge.
"Empty" containers retain product residue (liquid and/or vapor) and can be dangerous. DO NOT
pressurize, cut, weld, braze, solder, drill, grind, or expose such containers to heat, flame, sparks, static
electricity, or other sources of ignition; THEY MAY EXPLODE AND CAUSE INJURY OR DEATH.
Empty drums should be completely drained, properly bunged and promptly re- turned to a drum
reconditioner, or properly disposed of.
SECTION 6 ACCIDENTAL RELEASE MEASURES
NOTIFICATION PROCEDURES
Advise local and federal authorities as appropriate
LAND SPILL
Eliminate sources of ignition. Prevent additional discharge of material, if possible to do so without hazard.
For small spills implement cleanup procedures; for large spills implement cleanup procedures and, if in
public area, keep public away and advise authorities. Also, if this product is subject to CERCLA reporting
This information relates only to the specific material designated and may not be valid for such material used in combination with any other materials or in any process. The information
and recommendations contained herein is compiled from suppliers鈥? MSDS and are accurate and reliable to the best of Cannon Instrument Company鈥檚 knowledge and belief as of the
indicated revision date. No representation, warranty or guarantee, however, is made with regards to accuracy, reliability or completeness. Conditions of use of the material are under
the control of the user; therefore, it is the user's responsibility to satisfy himself as to the suitability and completeness of such information for his own particular use.
Product Name: General Purpose Viscosity
Standard 鈥? N.8
Revision Date: March 26, 2007
Page 4 of 10
MSDS ref CII07-008
(see Section 15 REGULATORY INFORMATION) notify the National Response Center.
Prevent liquid from entering sewers, watercourses, or low areas. Contain spilled liquid with sand or earth.
Do not use combustible materials such as sawdust.
Recover by pumping (use an explosion proof or hand pump) or with a suitable absorbent.
Consult an expert on disposal of recovered material and ensure conformity to local disposal regulations.
WATER SPILL
Eliminate sources of ignition. Warn occupants and shipping in surrounding and downwind areas of fire
and explosion hazard and request all to stay clear.
Remove from surface with suitable adsorbents. If allowed by local authorities and environmental
agencies, sinking and/or suitable dispersants may be used in non-confined waters.
Consult an expert on disposal of recovered material and ensure conformity to local disposal regulations.
SECTION 7 HANDLING AND STORAGE
HANDLING
Loading/unloading temperature (掳C/掳F): Ambient
Transport temperature (掳C/掳F): Ambient
Transport pressure (kPa): Ambient
Static accumulator: yes
STORAGE
Storage temperature (掳C/掳F): Ambient
Storage pressure (kPa) Ambient
Suitable materials and coatings: Not determined
Unsuitable materials and coatings: Not determined
ELECTROSTATIC ACCUMULATION HAZARD:
Use proper bonding and/or grounding procedure.
Additional information regarding safe handling of products with static accumulation potential can be
ordered by contacting the American Petroleum Institute (API) for API Recommended Practice 2003,
entitled "Protection Against Ignitions Arising Out of Static, Lightning, and Stray Currents" (American
Petroleum Institute, 1220 L Street Northwest, Washington, DC 20005), or the National Fire Protection
Association (NFPA) for NFPA 77 entitled "Static Electricity" (National Fire Protection Association, 1
Batterymarch Park, P.O. Box 9101, Quincy, MA 02269-9101).
STORAGE AND HANDLING:
Keep container closed. Handle and open containers with care. Store in a cool, well ventilated place away
from incompatible materials. Do NOT handle or store near an open flame, heat or other sources of
ignition. Protect material from direct sunlight. Material will accumulate static charges which may cause an
electrical spark (ignition source). Use proper bonding and/or grounding procedures. Do NOT pressurize,
cut, heat, or weld containers. Empty product containers may contain product residue. Do NOT reuse
empty containers without commercial cleaning or reconditioning.
SECTION 8 EXPOSURE CONTROLS/PERSONAL PROTECTION
WORKPLACE EXPOSURE GUIDELINES
OSHA REGULATION 29CFR1910.1000 PERMISSIBLE EXPOSURE LIMITS:
Xylenes: 50 ppm (180 mg/m3) TWA and a STEL of 150 ppm (655 mg/m3).
This information relates only to the specific material designated and may not be valid for such material used in combination with any other materials or in any process. The information
and recommendations contained herein is compiled from suppliers鈥? MSDS and are accurate and reliable to the best of Cannon Instrument Company鈥檚 knowledge and belief as of the
indicated revision date. No representation, warranty or guarantee, however, is made with regards to accuracy, reliability or completeness. Conditions of use of the material are under
the control of the user; therefore, it is the user's responsibility to satisfy himself as to the suitability and completeness of such information for his own particular use.
Product Name: General Purpose Viscosity
Standard 鈥? N.8
Revision Date: March 26, 2007
Page 5 of 10
MSDS ref CII07-008
Ethyl Benzene: 100 ppm (435 mg/m3) TWA and a STEL of 125 ppm (545 mg/m3).
ACGIH THRESHOLD LIMIT VALUES:
Xylene: 100 ppm (434 mg/m3) TWA and a STEL of 150 ppm (651 mg/m3)
Ethyl Benzene: 100 ppm (434 mg/m3) TWA and a STEL of 125 ppm (543 mg/m3).
ENGINEERING CONTROLS
The level of protection and types of controls necessary will vary depending upon potential exposure
conditions. Engineering controls are preferable to personal protective equipment. Control measures to
consider:
The use of local exhaust ventilation is recommended to control process emissions near the source.
Laboratory samples should be handled in a lab hood. Provide mechanical ventilation of confined spaces.
See respiratory protection recommendations. Use explosion-proof ventilation equipment.
PERSONAL PROTECTION
Personal protective equipment selections vary based on potential exposure conditions such as
applications, handling practices, concentration and ventilation. Information on the selection of protective
equipment for use with this material, as provided below, is based upon intended, normal usage.
For open systems where contact is likely, wear safety glasses with side shields, long sleeves, and
chemical resistant gloves.
Where contact may occur, wear safety glasses with side shields.
Where concentrations in air may exceed the limits given in this Section and engineering, work practice or
other means of exposure reduction are not adequate, NIOSH approved respirators may be necessary to
prevent overexposure by inhalation.
Respiratory Protection:
If engineering controls do not maintain airborne contaminant concentrations at a level which is adequate
to protect worker health, an approved respirator may be appropriate. Respirator selection, use, and
maintenance must be in accordance with regulatory requirements, if applicable.
For high airborne concentrations, use an approved supplied-air respirator, operated in positive pressure
mode. Supplied air respirators with an escape bottle may be appropriate when oxygen levels are
inadequate, gas/vapor warning properties are poor, or if air purifying filter capacity/rating may be
exceeded.
SPECIFIC HYGIENE MEASURES:
Always observe good personal hygiene measures, such as washing after handling the material and
before eating, drinking, and/or smoking. Routinely wash work clothing and personal protective equipment
to remove contaminants. Discard contaminated clothing and footwear that cannot be cleaned.
SECTION 9 PHYSICAL AND CHEMICAL PROPERTIES
GENERAL INFORMATION
Physical state: liquid
Form: liquid
Color: clear, colorless
Odor: characteristic aromatic odor
This information relates only to the specific material designated and may not be valid for such material used in combination with any other materials or in any process. The information
and recommendations contained herein is compiled from suppliers鈥? MSDS and are accurate and reliable to the best of Cannon Instrument Company鈥檚 knowledge and belief as of the
indicated revision date. No representation, warranty or guarantee, however, is made with regards to accuracy, reliability or completeness. Conditions of use of the material are under
the control of the user; therefore, it is the user's responsibility to satisfy himself as to the suitability and completeness of such information for his own particular use.
Product Name: General Purpose Viscosity
Standard 鈥? N.8
Revision Date: March 26, 2007
Page 6 of 10
MSDS ref CII07-008
Odor threshold: Not determined
IMPORTANT HEALTH, SAFETY AND ENVIRONMENTAL INFORMATION
Relative density (formerly Specific Gravity): 0.86
Bulk density g/cc: 0.86
Flash point 掳C (掳F) [method]: 29 掳C (84 掳F) [ASTM D56]
Flammable limits (approx. Volume % in air) - LEL: 1.0 UEL: 7.0
Autoignition temperature 掳C (掳F): 464掳C (867掳F)
Boiling point/range 掳C (掳F): 137-140 掳C (279-284 掳F)
Vapor density @ 101 kPa (air =1): >1
Vapor pressure @ 20掳C (68 掳F), kPa (mm Hg): 8
Evaporation rate (n-butyl acetate =1): 0.7
pH: not applicable
Log Pow (n-Octanol/water partition coefficient): not determined
Solubility in water (25 掳C): 0.02 wt% (calculated)
Viscosity @ 40掳C cSt (mm2/sec): 0.4
100掳C cSt (mm2/sec): not available
OTHER INFORMATION
Freezing point 掳C (掳F): -25 掳C (-13 掳F)
Melting Point 掳C (掳F): -25 掳C (-13 掳F)
Pour point 掳C (掳F): not available
Molecular weight: 102
Hygroscopic: not available
Coefficient of thermal expansion: not available
SECTION 10 STABILITY AND REACTIVITY
STABILITY: Stable
CONDITIONS TO AVOID: Strong oxidizing agents.
MATERIALS TO AVOID: Strong oxidizing agents.
HAZARDOUS DECOMPOSITION PRODUCTS: not applicable. Potentially hazardous combustion products may
be formed under fire conditions (incomplete combustion)
HAZARDOUS POLYMERIZATION: Will not occur
SECTION 11 TOXICOLOGICAL INFORMATION
Toxicological Data:
Xylene Oral rat LD59: 4300 mg/kg; inhalation rat LC50: 5000 ppm/4H; skin rabbit LD50: >1700 mg/kg;
irritation eye rabbit: 87 mg mild(Std Draize); irritation skin rabbit 500 mg/24H moderate (Std
Draize); investigated as tumorigen, mutagen, reproductive effector
Ethylbenzene Oral rat LD50: 3500 mg/kg; skin rabbit LD50: 17800 uL/kg; investigated as a tumorigen,
mutagen, reproductive effector
This information relates only to the specific material designated and may not be valid for such material used in combination with any other materials or in any process. The information
and recommendations contained herein is compiled from suppliers鈥? MSDS and are accurate and reliable to the best of Cannon Instrument Company鈥檚 knowledge and belief as of the
indicated revision date. No representation, warranty or guarantee, however, is made with regards to accuracy, reliability or completeness. Conditions of use of the material are under
the control of the user; therefore, it is the user's responsibility to satisfy himself as to the suitability and completeness of such information for his own particular use.
Product Name: General Purpose Viscosity
Standard 鈥? N.8
Revision Date: March 26, 2007
Page 7 of 10
MSDS ref CII07-008
Reproductive Toxicity: May cause teratogenic effects.
Please refer to Section 3 for available information on potential health effects.
SECTION 12 ECOLOGICAL INFORMATION
The information given is based on data available for the material, the components of the material, and
similar materials.
ENVIRONMENTAL FATE
Following data for xylene: When released into the soil, this material will evaporate to a moderate extent;
is expected to leach into groundwater, and will biodegrade to a moderate extent.
When released into water, this material will evaporate to a moderate extent; is expected to leach into
groundwater, and will biodegrade to a moderate extent.
When released into the air, this material may be moderately degraded by reaction with photochemically-
produced hydroxyl radicals and is expected to have a half-life of less than one day.
This material is not expected to significantly bioaccumulate.
ENVIRONMENTAL TOXICITY
Following data for xylene: This material is expected to be slightly toxic to aquatic life. The LC50/96-hour
values for fish are between 10 and 100 mg/l.
MOBILITY No data available
PERSISTENCE AND DEGRADABILITY No data available
Biodegradation: No data available
Hydrolysis: No data available
Photolysis: No data available
Atmospheric oxidation: No data available
BIOACCUMULATION POTENTIAL No data available
OTHER ECOLOGICAL INFORMATION
VOC 100%
COD: No data available
SECTION 13 DISPOSAL CONSIDERATIONS
Disposal recommendations are based on material as supplied. Disposal must be in accordance with
current applicable laws and regulations, and material characteristics at time of disposal.
DISPOSAL RECOMMENDATIONS
Empty packaging should be taken for recycling, recovery or disposal through a suitably qualified or
licensed contractor. Care should in any case be taken to ensure compliance with national and local
regulations.
This product is NOT suitable for disposal by either landfill or via municipal sewers, drains, natural streams
or rivers.
This information relates only to the specific material designated and may not be valid for such material used in combination with any other materials or in any process. The information
and recommendations contained herein is compiled from suppliers鈥? MSDS and are accurate and reliable to the best of Cannon Instrument Company鈥檚 knowledge and belief as of the
indicated revision date. No representation, warranty or guarantee, however, is made with regards to accuracy, reliability or completeness. Conditions of use of the material are under
the control of the user; therefore, it is the user's responsibility to satisfy himself as to the suitability and completeness of such information for his own particular use.
Product Name: General Purpose Viscosity
Standard 鈥? N.8
Revision Date: March 26, 2007
Page 8 of 10
MSDS ref CII07-008
This product is ashless and can be burned directly in appropriate equipment.
REGULATORY DISPOSAL INFORMATION
Empty container warning (where applicable): empty containers may retain residue and can be
dangerous. Do not pressurize, cut, weld, braze, solder, drill, grind or expose such containers to heat,
flame, sparks, static electricity, or other sources of ignition; they may explode and cause injury or death.
Do not attempt to refill or clean container since residue is difficult to remove. Empty drums should be
completely drained, properly bunged and promptly returned to a drum reconditioner. All containers
should be disposed of in an environmentally safe manner and in accordance with governmental
regulations.
SECTION 14 TRANSPORT INFORMATION
Note: The information provided below may not apply to all shipping situations. Consult appropriate
Dangerous Goods Regulations for additional requirements and mode-specific, material-specific, or
quantity-specific shipping requirements.
United States Department of Transportation (US DOT):
UN/ID# Proper Shipping Name Class/Division Hazard Label(s) Packing Group
UN1307 Xylenes 3 Flammable Liquid III
International Air Transport Association (IATA):
UN/ID# Proper Shipping Name Class/Division Hazard Label(s) Packing Group
UN1307 Xylenes 3 Flammable Liquid III
SECTION 15 REGULATORY INFORMATION
OSHA HAZARD COMMUNICATION STANDARD: This material is classified as hazardous in accordance with
OSHA 29 CFR 1910.1200.
NATIONAL CHEMICAL INVENTORY LISTING:
This product, and/ or its constituents, is listed on the US EPA/ TSCA (Toxic Substances Control Act)
Inventory
COMMUNITY RTK:
Chemical name CAS Number Typical Value
m-xylene 108-38-3. 40-65%
o-xylene 95-47-6 15-20%
p-xylene 106-42-3 <20%
Ethyl benzene 100-41-4 15-25%
This information relates only to the specific material designated and may not be valid for such material used in combination with any other materials or in any process. The information
and recommendations contained herein is compiled from suppliers鈥? MSDS and are accurate and reliable to the best of Cannon Instrument Company鈥檚 knowledge and belief as of the
indicated revision date. No representation, warranty or guarantee, however, is made with regards to accuracy, reliability or completeness. Conditions of use of the material are under
the control of the user; therefore, it is the user's responsibility to satisfy himself as to the suitability and completeness of such information for his own particular use.
Product Name: General Purpose Viscosity
Standard 鈥? N.8
Revision Date: March 26, 2007
Page 9 of 10
MSDS ref CII07-008
CERCLA:
Chemical name CAS Number Typical Value Component RQ
m-xylene 108-38-3. 40-65% 1000
o-xylene 95-47-6 15-20% 1000
p-xylene 106-42-3 <20% 100
Ethyl benzene 100-41-4 15-25% 1000
CWA / OPA: no
SARA (311/312) REPORTABLE HAZARD CATEGORIES:
Acute, yes; Chronic, yes; Fire, yes; Pressure, no
SARA (313) TOXIC RELEASE INVENTORY: listed
Chemical Name CAS Number Typical Value
m-xylene 108-38-3. 40-65%
o-xylene 95-47-6 15-20%
p-xylene 106-42-3 <20%
Ethyl benzene 100-41-4 15-25%
International chemical inventories and hazard classifications
This product and/ or its components are on the Canadian Domestic Substance List/ NDSL
WHMIS Classifications (Canada):
B2 - Flammable and combustible material - Flammable liquid
D2A - Poisonous and infectious material - Other effects - Very toxic
D2B - Poisonous and infectious material - Other effects - Toxic
WHMIS Health Effects Criteria Met by this Chemical:
D2B - Skin irritation - toxic 鈥? other
D2A - Teratogenicity and embryotoxicity - very toxic - other
WHMIS Ingredient Disclosure List:
Not included. Meets criteria for disclosure at 0.1% or greater.
This product and/ or its components are on EINECS (European Inventory of Existing Chemical
Substances) and/ or ELINCS (European Library of Notified Chemical Substances)
EU Hazard Classification, risk and safety phrases (Europe):
Xn Harmful
R10: Flammable
R20/21: Harmful by inhalation and in contact with skin
This information relates only to the specific material designated and may not be valid for such material used in combination with any other materials or in any process. The information
and recommendations contained herein is compiled from suppliers鈥? MSDS and are accurate and reliable to the best of Cannon Instrument Company鈥檚 knowledge and belief as of the
indicated revision date. No representation, warranty or guarantee, however, is made with regards to accuracy, reliability or completeness. Conditions of use of the material are under
the control of the user; therefore, it is the user's responsibility to satisfy himself as to the suitability and completeness of such information for his own particular use.
Product Name: General Purpose Viscosity
Standard 鈥? N.8
Revision Date: March 26, 2007
Page 10 of 10
MSDS ref CII07-008
R38: Irritating to skin
S2: Keep out of reach of children
S25: Avoid contact with the eyes
SECTION 16 OTHER INFORMATION
THIS SAFETY DATA SHEET CONTAINS THE FOLLOWING REVISIONS:
Revision Summary:
鈥? October 15, 2005 -- This MSDS has been fully reviewed and reformatted to conform to changes
in standard format
鈥? January 8, 2007 鈥? MSDS updated based on supplier information
鈥? February 27, 2007: Added Canadian and European classification and labeling information,
based on current regulations and/or recommendations from suppliers (see Section 15)
鈥? March 26, 2007: Updated and standardized format of Transport Information (see Section 14)
NOTES:
This information relates only to the specific material designated and may not be valid for such material used in combination with any other materials or in any process. The information
and recommendations contained herein is compiled from suppliers鈥? MSDS and are accurate and reliable to the best of Cannon Instrument Company鈥檚 knowledge and belief as of the
indicated revision date. No representation, warranty or guarantee, however, is made with regards to accuracy, reliability or completeness. Conditions of use of the material are under
the control of the user; therefore, it is the user's responsibility to satisfy himself as to the suitability and completeness of such information for his own particular use.
|