Aluminum Polyurea, Part B Page 1
MSDS Number: ureth0000al October 24, 2005
________________________________________
MATERIAL SAFETY DATA SHEET
1. CHEMICAL PRODUCT AND COMPANY IDENTIFICATION
Product Identification
______________________
Product Name: Aluminum Polyurea, Part B
Product Number: pails, drums, totes
Chemical Name: Polyurea System Resin Component
Chemical Family: Resin
CAS Number: Blend
Company Identification
______________________
ERSystems- Elastomeric Roofing Systems, Inc.
6900 Bleck Dr
Rockford, MN 55373 USA
1-800-403-7747 (For product information)
1-800-535-5053 Infotrac (For emergencies)
SPECIAL NOTES:
Polyurea system resin component. Part B (Part 2) of a two part system.
2. COMPOSITION/INFORMATION ON INGREDIENTS
COMPONENT LISTING:
Chemical Name
_____________ Amount
________ CAS Number
__________
POLYOL < 75.0 % N/A
UV STABILIZER < 5.0 % N/A
ADDITIVE < 10.0 % N/A
DIETHYLTOLUENEDIAMINE < 15.0 % 68479-98-1
DRYING AGENT < 3.0 % N/A
FLAME RETARDANT < 7.0 % N/A
CATALYST < 1.0 % N/A
(See Section 8 for exposure guidelines)
(See Section 15 for regulatory information)
Aluminum Polyurea, Part B Page 2
MSDS Number: ureth0000al October 24, 2005
____________________________________________________________________________________________________
3. HAZARDS IDENTIFICATION
***************** EMERGENCY OVERVIEW *****************
* *
* WARNING *
* *
* May be harmful or fatal if swallowed. Material is *
* corrosive-causes eye and skin burns. May cause eye *
* irritation. *
* *
**********************************************************
HMIS Rating - Health: 3
Flammability: 2
Reactivity: 1
NFPA/HMIS Definitions: (0-Least, 1-Slight, 2-Moderate, 3-High,
4-Extreme). These values are obtained using the guidelines or published
evaluations prepared by the National Fire Protection Association (NFPA) or
the National Paint and Coating Association (for HMIS ratings).
POTENTIAL HEALTH EFFECTS
EYE:
Causes eye irritation.
SKIN:
Brief contact may cause skin irritation. Prolonged contact, as with
clothing wetted with material, may cause more severe irritation and
discomfort, seen as local redness and swelling.
INHALATION:
Vapors or mist, in excess of permissible concentrations, or in unusually
high concentrations generated from spraying or heating the material may
cause irritation of the nose and throat, headache, nausea, and drowsiness.
INGESTION:
Causes burning of mouth, throat, and stomach with abdominal and chest
pain, nausea, vomiting, diarrhea, and weakness. Aspiration may occur
during swallowing or vomiting, resulting in lung damage.
Aluminum Polyurea, Part B Page 3
MSDS Number: ureth0000al October 24, 2005
____________________________________________________________________________________________________
4. FIRST AID MEASURES
EYE CONTACT FIRST AID:
After initial flushing, remove any contact lenses and continue flushing
for at least 15 minutes. Get medical attention if irritation develops or
persists.
SKIN CONTACT FIRST AID:
Immediately wash skin with plenty of soap and water while removing
contaminated clothing and shoes. Wash contaminated clothing before reuse.
Get medical attention if irritation develops or persists.
INHALATION FIRST AID:
If inhaled, remove to fresh air. If not breathing, give artificial
respiration or give oxygen by trained personnel.
INGESTION FIRST AID:
If person is conscious and can swallow, immediately give two glasses of
water, but do NOT induce vomiting. Material is corrosive. If vomiting
occurs, give fluids again. Obtain medical attention. Never give anything
by mouth to an unconscious person.
5. FIRE FIGHTING MEASURES
FLAMMABLE PROPERTIES
PMCC Flash Point: 93 C (199.4 F)
Autoignition Temperature: N/A
FLAMMABLE LIMITS IN AIR
LEL: N/A
UEL: N/A
FLAMMABLE PROPERTIES:
Full emergency equipment with self contained breathing apparatus and full
protective clothing should be worn.
EXTINGUISHING MEDIA:
Water, carbon dioxide, foam or dry powder.
FIRE FIGHTING INSTRUCTIONS:
As in any fire, wear self-contained breathing apparatus pressure-demand
MSHA/NIOSH (approved or equivalent) and full protective gear.
Aluminum Polyurea, Part B Page 4
MSDS Number: ureth0000al October 24, 2005
____________________________________________________________________________________________________
6. ACCIDENTAL RELEASE MEASURES
SAFEGUARDS (PERSONNEL):
Ventilate spill area. Avoid breathing vapor. Wear appropriate personal
protective equipment.
INITIAL CONTAINMENT:
Contain spilled material. Absorb spills with inert material.
LARGE SPILLS PROCEDURE:
Absorb spill with inert material (e g, dry sand or earth), then place in a
chemical waste container. Treat or dispose of waste material in
accordance with all local, state/provincial, and national requirements.
MISCELLANEOUS:
Prevent entry into sewers and waterways. Avoid contact with skin, eyes,
or clothing.
7. HANDLING AND STORAGE
RECOMMENDED STORAGE TEMPERATURE
Minimum: 15.6 C (60.1 F)
Maximum: 26.7 C (80.1 F)
SHELF LIFE: (in original, sealed containers)
8 months @ 26.7 C
HANDLING (PERSONNEL):
Avoid contact with eyes, skin, and clothing. Wash hands thoroughly after
handling. Eye wash should be available nearby when this product is
handled or used.
HANDLING (PHYSICAL ASPECTS):
Provide appropriate ventilation. Close container after each use. Keep
container closed to avoid contamination. Keep out of reach of children.
STORAGE PRECAUTIONS:
Avoid extreme temperatures. Keep container closed when not in use. Store
in a cool dry place. Water contamination should be avoided. Is stored
above 100F, a nitrogen atmosphere is recommended.
Aluminum Polyurea, Part B Page 5
MSDS Number: ureth0000al October 24, 2005
____________________________________________________________________________________________________
8. EXPOSURE CONTROLS / PERSONAL PROTECTION
EYE / FACE PROTECTION REQUIREMENTS:
Wear safety glasses. A respiratory protection program that meets OSHA's
29 CFR 1910-134 and ANSI Z88-2 requirements must be followed whenever
workplace conditions warrant a respirator's use. Do not wear contacts.
SKIN PROTECTION REQUIREMENTS:
Selection of specific items such as gloves, boots, apron or full-body suit
will depend on operation. Gloves resistant to chemicals and petroleum
distillates must be worn. Wash hands thoroughly after handling.
RESPIRATORY PROTECTION REQUIREMENTS:
When there is potential for airborne exposures in excess of applicable
limits, wear NIOSH/MSHA approved respiratory protection.
EXPOSURE GUIDELINES:
No Information Available.
9. PHYSICAL AND CHEMICAL PROPERTIES
FORM ..................: Liquid
COLOR .................: Light yellow
ODOR ..................: Mild
SOLUBILITY IN WATER ...: Moderately soluble
BULK DENSITY ..........: 8.48 lb/USg
PH ....................: 7
VISCOSITY .............: 760 mPa.s (25C)
10. STABILITY AND REACTIVITY
STABILITY:
Stable. Do not heat.
POLYMERIZATION:
Will not occur.
DECOMPOSITION:
Decomposition may produce carbon monoxide and carbon dioxide.
CONDITIONS TO AVOID:
Avoid moisture.
Aluminum Polyurea, Part B Page 6
MSDS Number: ureth0000al October 24, 2005
____________________________________________________________________________________________________
11. TOXICOLOGICAL INFORMATION
No information available.
12. ECOLOGICAL INFORMATION
No information available.
13. DISPOSAL CONSIDERATIONS
WASTE DISPOSAL:
Treat or dispose of waste material in accordance with all local,
state/provincial, and national requirements.
CONTAINER DISPOSAL:
Steel drums must be emptied and can be sent to a drum reconditioner for
reuse, a scrap metal dealer or an approved landfill. Refer to 40 CFR
261.7 (residues of hazardous waste in empty containers).
14. TRANSPORTATION INFORMATION
PRODUCT LABEL .............: Aluminum Polyurea, Part B
D.O.T. SHIPPING NAME ......: Corrosive liquids, toxic
TECHNICAL SHIPPING NAME ...: N/A
D.O.T. HAZARD CLASS .......: Class 8
UN NUMBER .................: UN 2922
15. REGULATORY INFORMATION
No information available.
Aluminum Polyurea, Part B Page 7
MSDS Number: ureth0000al October 24, 2005
____________________________________________________________________________________________________
16. OTHER INFORMATION
PREPARED BY .......: Laura Vollenweider
APPROVED BY .......: Laura Vollenweider
TITLE .............: Chemist
APPROVAL DATE .....: October 24, 2005
SUPERCEDES DATE ...: December 27, 2004
MSDS NUMBER .......: ureth0000al
RTN NUMBER ........: 00000073 (Official Copy)
ADDITIONAL INFORMATION:
The data in this Material Safety Data Sheet relates only to the specific
material designated herein.
**********************************************************************
To the best of our knowledge, the information contained in this MSDS is
accurate. It is intended to assist the user in his evaluation of the
product's hazards, and safety precautions to be taken in its use. The
data in this MSDS relate only to the specific material designated herein.
We do not assume liability for the use of, or reliance on this
information, nor do we guarantee its accuracy or completeness.
**********************************************************************
END OF MSDS
**********************************************************************
|