MATERIAL SAFETY DATA SHEET N.A.=Not Applicable
(SIMILAR TO OSHA FORM 174) Not Est.=Not Established
Prop.=Proprietary
SECTION 1-MANUFACTURER/DISTRIBUTOR INFORMATION
Product Name: Formula 6 Floor Finish Remover
Supplier's Name: INSCO, Inc.
Supplier's Address: 1611 Ralston Street, Wilson, NC 27893 Emergency Phone #: (800)-849-1133
HMIS Hazard Code: Health:2 Flammability:0 Reactivity:0 Other:0 Chemical Name: N.A. Proprietary Blend
Chemical Family: Alkaline Detergent Formula: N.A. Blended Product
D.O.T. Shipping Name: CORROSIVE LIQUID n.o.s. (contains sodium hydroxide)
Hazard Class: 8 D.O.T. ID#: UN1760
SECTION 2-HAZARDOUS INGREDIENTS
CHEMICAL NAME CAS NO. % Concentrate Range Hazard Ratings (TLV/PEL)
2-Amino Ethanol 141-43-5 PROP. 3 ppm
2 mg/m3
Sodium Hydroxide 1310-73-2 PROP.
SECTION 4-FIRE AND EXPLOSION DATA
SECTION 3-PHYSICAL DATA
Boiling Point (F): 2120 Specific Gravity: 1.04 Flash Point (F): None To Boiling (TOC)
Vapor Pressure: = To Water Evaporation Rate: = To Flammable Limits: Not Est.
Vapor Density: = To Water Water Unusual Fire & Explosion Hazards: Heated
Solubility In Water: Complete material may liberate toxic and irritating fumes.
Appearance: Clear, Thin, Red Wear self contained breathing apparatus.
Liquid
Odor: Citrus
SECTION 5-HEALTH HAZARD DATA
Route(s) of Entry: Inhalation:No Skin:Yes Ingestion:Yes Threshold Limit Value: Not Est.
Effects of Overexposure: Causes skin and eye irritation. Harmful if swallowed. May cause severe mucosal damage and gastric
distress. May cause systemic intoxication.
Emergency & First Aid Procedures: For Eyes: Flush with water for at least fifteen minutes. Get medical aid. For Skin: Thoroughly
wash with water and apply emollient creme. If irritation persists get medical aid. If Ingested: Do not induce vomiting. Give milk, egg
white, gelatin, or water. Get immediate medical aid.
Conditions Aggravated by Exposure: May aggravate existing dermatitis and irritate sensitive skin.
Listed Carcinogen, Mutagen, Teratogen (Ingredient, Source, Amount): None
SECTION 6-REACTIVITY DATA SECTION 7-SPILL OR LEAK PROCEDURES
Steps to be taken if material is released or spilled:
Stability: Stable
Recontainerize by mopping, wet vacuum, or using a suitable
Conditions to Avoid: None
absorbent. Rinse remaining material to drains. Be cautious of
Incompatibility: Acids and Oxidizers
slippery floors.
Hazardous Decomposition Products: Carbon Oxides and
Waste disposal method: Follow local, state, and federal
Amines
regulations.
Hazardous Polymerization: Will not occur.
SECTION 9-SPECIAL PRECAUTIONS
SECTION 8-SPECIAL PROTECTION INFORMATION
Precautions to be taken in handling and storage: Store
Respiratory Protection: Generally not required.
between 400 and 1200 F.
Ventilation: Local.
Other Precautions: Keep out of reach of children. For sale to,
Protective Gloves: Rubber or latex.
use and storage by service personnel only.
Eye Protection: Goggles or safety glasses with shields
Other Protective Equipment: Rubber boots should be worn if
working in standing solutions
The information contained in this MSDS was obtained from current and reliable sources, however the data is provided without any warranty, expressed
or implied, regarding its correctness or accuracy. Since the conditions or handling, storage and disposal of this product are beyond the control of this
company, it is not responsible for loss, injury and expense arising out of the product's improper use. No warranty, expressed or inferred, regarding the
product described in this MSDS shall be created or inferred by any statement in this MSDS. Various government agencies may have specific regula-
tions regarding the transportation, handling, storage, use or disposal of this product which may not be covered by this MSDS. The user is responsible
for full compliance.
DATE PREPARED-10/5/00 By: G.C.
|