**** SECTION 2 - COMPOSITION, INFORMATION ON INGREDIENTS ****
+----------------+--------------------------------------+----------+-----------+
| CAS# | Chemical Name | % | EINECS# |
|----------------|--------------------------------------|----------|-----------|
| 109-55-7 |3-Dimethylaminopropylamine | 99 | 203-680-9 |
+----------------+--------------------------------------+----------+-----------+
Hazard Symbols: F C
Risk Phrases: 10 22 34 43
**** SECTION 3 - HAZARDS IDENTIFICATION ****
EMERGENCY OVERVIEW
Flammable. Harmful if swallowed. Causes burns. May cause
sensitization by skin contact.Corrosive.
Potential Health Effects
Eye:
Causes eye burns. Lachrymator (substance which increases the flow
of tears).
Skin:
Harmful if absorbed through the skin. Causes skin burns.
Ingestion:
May cause severe and permanent damage to the digestive tract. Causes
gastrointestinal tract burns. May be harmful if swallowed.
Inhalation:
Causes chemical burns to the respiratory tract. Vapors may cause
dizziness or suffocation.
Chronic:
No information found.
**** SECTION 4 - FIRST AID MEASURES ****
Eyes:
Get medical aid immediately. Do NOT allow victim to rub eyes or keep
eyes closed. Extensive irrigation with water is required (at least 30
minutes).
Skin:
Get medical aid immediately. Immediately flush skin with plenty of
water for at least 15 minutes while removing contaminated clothing
and shoes. Destroy contaminated shoes.
Ingestion:
Get medical aid immediately. Do NOT induce vomiting. If conscious
and alert, rinse mouth and drink 2-4 cupfuls of milk or water. Wash
mouth out with water.
Inhalation:
Get medical aid immediately. If not breathing, give artificial
respiration. If breathing is difficult, give oxygen. Do NOT use
mouth-to-mouth resuscitation.
Notes to Physician:
**** SECTION 5 - FIRE FIGHTING MEASURES ****
General Information:
As in any fire, wear a self-contained breathing apparatus in
pressure-demand, MSHA/NIOSH (approved or equivalent), and full
protective gear. Vapors may form an explosive mixture with air.
Vapors can travel to a source of ignition and flash back. During a
fire, irritating and highly toxic gases may be generated by thermal
decomposition or combustion. Use water spray to keep fire-exposed
containers cool. Containers may explode in the heat of a fire.
Flammable liquid and vapor. Vapors may be heavier than air. They
can spread along the ground and collect in low or confined areas.
Extinguishing Media:
For small fires, use dry chemical, carbon dioxide, water spray or
alcohol-resistant foam. For large fires, use water spray, fog, or
alcohol-resistant foam. Use water spray to cool fire-exposed
containers. Water may be ineffective. Do NOT get water inside
containers. Do NOT use straight streams of water. Cool containers
with flooding quantities of water until well after fire is out.
**** SECTION 6 - ACCIDENTAL RELEASE MEASURES ****
General Information: Use proper personal protective equipment as indicated
in Section 8.
Spills/Leaks:
Absorb spill with inert material (e.g. vermiculite, sand or earth),
then place in suitable container. Clean up spills immediately,
observing precautions in the Protective Equipment section. Remove all
sources of ignition. Use a spark-proof tool. Provide ventilation. Do
not get water inside containers. A vapor suppressing foam may be
used to reduce vapors.
**** SECTION 7 - HANDLING and STORAGE ****
Handling:
Wash thoroughly after handling. Ground and bond containers when
transferring material. Use spark-proof tools and explosion proof
equipment. Empty containers retain product residue, (liquid and/or
vapor), and can be dangerous. Keep container tightly closed. Keep
away from heat, sparks and flame. Do not get on skin or in eyes.
Avoid ingestion and inhalation. Use with adequate ventilation.
Discard contaminated shoes. Do not pressurize, cut, weld, braze,
solder, drill, grind, or expose empty containers to heat, sparks or
open flames.
Storage:
Keep away from heat, sparks, and flame. Keep away from sources of
ignition. Keep container closed when not in use. Store in a cool,
dry, well-ventilated area away from incompatible substances.
Flammables-area.
**** SECTION 8 - EXPOSURE CONTROLS, PERSONAL PROTECTION ****
Engineering Controls:
Facilities storing or utilizing this material should be equipped
with an eyewash facility and a safety shower. Use adequate
ventilation to keep airborne concentrations low.
Exposure Limits
CAS# 109-55-7:
Russia: 2 mg/m3 TWA
Personal Protective Equipment
Eyes:
Wear appropriate protective eyeglasses or chemical
safety goggles as described by OSHA's eye and face
protection regulations in 29 CFR 1910.133 or European
Standard EN166.
Skin:
Wear appropriate protective gloves to prevent skin
exposure.
Clothing:
Wear a chemical apron. Wear appropriate protective
clothing to prevent skin exposure.
Respirators:
A respiratory protection program that meets OSHA's 29
CFR 1910.134 and ANSI Z88.2 requirements or European
Standard EN 149 must be followed whenever workplace
conditions warrant respirator use. Follow the OSHA
respirator regulations found in 29 CFR 1910.134 or
European Standard EN 149. Use a NIOSH/MSHA or
European Standard EN 149 approved respirator if
exposure limits are exceeded or if irritation or
other symptoms are experienced.
**** SECTION 9 - PHYSICAL AND CHEMICAL PROPERTIES ****
Physical State: Liquid
Color: Clear
Odor: None reported.
pH: Not available.
Vapor Pressure: 8 hPa @ 20 C
Viscosity: 1.6 mPas 20 deg C
Boiling Point: 133 deg C @ 760.00mm Hg
Freezing/Melting Point: -60 deg C
Autoignition Temperature: 305 deg C ( 581.00 deg F)
Flash Point: 32 deg C ( 89.60 deg F)
Explosion Limits, lower: 3.00 vol %
Explosion Limits, upper: .00 vol %
Decomposition Temperature:
Solubility in water: soluble
Specific Gravity/Density: .8120g/cm3
Molecular Formula: C5H14N2
Molecular Weight: 102.18
**** SECTION 10 - STABILITY AND REACTIVITY ****
Chemical Stability:
Stable under normal temperatures and pressures.
Conditions to Avoid:
Incompatible materials, ignition sources, moisture, excess heat.
Incompatibilities with Other Materials:
Strong oxidizing agents, acid chlorides, carbon dioxide, alliphatic
amines, acid anhydrides.
Hazardous Decomposition Products:
Nitrogen oxides, carbon monoxide, carbon dioxide, nitrogen.
Hazardous Polymerization: Has not been reported.
**** SECTION 11 - TOXICOLOGICAL INFORMATION ****
RTECS#:
CAS# 109-55-7: TX7525000
LD50/LC50:
CAS# 109-55-7: Draize test, rabbit, eye: 5 mg Moderate; Oral, rat:
LD50 = 1870 mg/kg; Skin, rabbit: LD50 = 600 uL/kg.
Skin, rabbit:
Carcinogenicity:
3-Dimethylaminopropylamine -
Not listed by ACGIH, IARC, or NTP.
Other:
See actual entry in RTECS for complete information.
**** SECTION 12 - ECOLOGICAL INFORMATION ****
Other
No information available.
**** SECTION 13 - DISPOSAL CONSIDERATIONS ****
Dispose of in a manner consistent with federal, state, and local regulations.
**** SECTION 14 - TRANSPORT INFORMATION ****
IATA
Shipping Name: AMINES, LIQUID, CORROSIVE, FLAMMABLE, N.O.S.*
Hazard Class: 8 (3)
UN Number: 2734
Packing Group: II
IMO
Shipping Name: AMINES, LIQUID, CORROSIVE, FLAMMABLE, N.O.S.
Hazard Class: 8 (3)
UN Number: 2734
Packing Group: II
RID/ADR
Shipping Name: AMINES, LIQUID, CORROSIVE, FLAMMABLE, N.O.S.
Hazard Class: 8
UN Number: 2734
Packing group: II
**** SECTION 15 - REGULATORY INFORMATION ****
European/International Regulations
European Labeling in Accordance with EC Directives
Hazard Symbols: F C
Risk Phrases:
R 10 Flammable.
R 22 Harmful if swallowed.
R 34 Causes burns.
R 43 May cause sensitization by skin contact.
Safety Phrases:
S 9 Keep container in a well-ventilated place.
S 16 Keep away from sources of ignition - No
smoking.
S 26 In case of contact with eyes, rinse immediately
with plenty of water and seek medical advice.
S 33 Take precautionary measures against static
discharges.
S 36/37/39 Wear suitable protective clothing, gloves
and eye/face protection.
S 45 In case of accident or if you feel unwell, seek
medical advice immediately (show the label where
possible).
WGK (Water Danger/Protection)
CAS# 109-55-7: 2
Canada
CAS# 109-55-7 is listed on Canada's DSL List.
CAS# 109-55-7 is not listed on Canada's Ingredient Disclosure List.
US FEDERAL
TSCA
CAS# 109-55-7 is listed on the TSCA inventory.
**** SECTION 16 - ADDITIONAL INFORMATION ****
MSDS Creation Date: 2/12/1998 Revision #2 Date: 3/18/2003
The information above is believed to be accurate and represents the best
information currently available to us. However, we make no warranty of
merchantability or any other warranty, express or implied, with respect to
such information, and we assume no liability resulting from its use. Users
should make their own investigations to determine the suitability of the
information for their particular purposes. In no way shall the company be
liable for any claims, losses, or damages of any third party or for lost
profits or any special, indirect, incidental, consequential or exemplary
damages, howsoever arising, even if the company has been advised of
the possibility of such damages.
--------------------------------------------------------------------------------
--------------------------------------------------------------------------------
|
|
|
| ALL MSDS PAGES IN THIS GROUP
| | NAME | CAS |
|
4-Hydroxybenzophenone, 99+%
| 1137-42-4 |
|
Chlorobenzene, 99+%
| 108-90-7 |
|
Chlorobenzene, Reagent ACS, 99.5% (GC)
| 108-90-7 |
|
Chloroform, preserved with 0.75% Ethanol
| 64-17-5 |
|
Chloroform, Reagent ACS, 99.8% (GC)
| 67-66-3 |
|
2-Amino-6-Methoxybenzothiazole, Tech.
| 1747-60-0 |
|
Cholesterol, 95%
| 57-88-5 |
|
Choline Chloride, 99%
| 67-48-1 |
|
Chromium(VI) oxide, flakes, 99+%
| 1333-82-0 |
|
N,N-Dimethylindoaniline (Pract), 78% (UV-Vis)
| 2150-58-5 |
|
Chromium(VI) oxide, reagent ACS, 98+%
| 1333-82-0 |
|
Methylene violet (bernthsen), high purity biological stain
| 2516-05-4 |
|
3-Dimethylaminopropylamine, 99%
| 109-55-7 |
|
Cobalt (II) Nitrate Hexahydrate, 99%
| 10026-22-9 |
|
Cobalt(II) Nitrate, Hexahydrate, Reagent ACS (Crystals)
| 10026-22-9 |
|
D(+)-trehalose dihydrate min. 99% (hplc)
| 6138-23-4 |
|
Cobalt(II) chloride hexahydrate, p.a.
| 7791-13-1 |
|
Cobalt(II) chloride, hexahydrate, reagent ACS
| 7791-13-1 |
|
Copper, 99%, -45 Micron Powder
| 7440-50-8 |
|
Cupferron, P.A.
| 135-20-6 |
|
Copper (II) Oxide, 99.999%
| 1317-38-0 |
|
Copper (II) Oxide, P.A.
| 1317-38-0 |
|
Copper (II) Oxide, Black, Reagent ACS (Powder)
| 1317-38-0 |
|
Copper(II) sulfate, anhydrous, p.a.
| 7758-98-7 |
|
Beta-Apo-Oxytetracycline,"Can be Used as Secondary Standard"
| 18751-99-0 |
|
Tolylene-2,4-Diisocyanate, Tech., 80%
| 584-84-9 |
|
Copper(II) sulfate pentahydrate, p.a.
| 7758-98-7 |
|
Copper(II) sulfate pentahydrate, reagent ACS
| 7758-98-7 |
|
N,N'-Di-N-Butylthiourea, 99%
| 109-46-6 |
|
5-Aminosalicylic Acid, 95%
| 89-57-6 |
|
Butyl Benzoate, 98%
| 136-60-7 |
|
Dl-sec-phenethyl alcohol, 99+%
| 98-85-1 |
|
D-(-)-Fructose, 98%
| 57-48-7 |
|
D-Sorbitol, 97%
| 50-70-4 |
|
Decahydronaphthalene, mixture of cis and trans, 98%
| 91-17-8 |
|
2,6-Di-tert-butyl-4-methylphenol, 99%
| 128-37-0 |
|
2-Aminothiophenol, 98% (GC)
| 137-07-5 |
|
2-Methyl-beta-naphthothiazole, 98%
| 2682-45-3 |
|
Di-n-butylamine 99%
| 111-92-2 |
|
tert-Butyl bromoacetate, 99%
| 5292-43-3 |
|
1,4-Dimethoxybenzene, 99+%
| 150-78-7 |
|
5-Chloro-2-Methylbenzoxazole, 99+% (GC)
| 19219-99-9 |
|
Ammonium oxalate, monohydrate, p.a.
| 1113-38-8 |
|
L-Lactic Acid, 20 Wt. % Solution in Water
| 79-33-4 |
|
Benzenesulfonic acid, tech., 90%
| 98-11-3 |
|
Molybdic acid p.a.
| 7782-91-4 |
|
Poly(phenylene sulfide) nominal m.w. 10000 ,powder
| 9016-75-5 |
|
2-Pyrrolidinone, 98%
| 616-45-5 |
|
Ethyl Caprate, 99+%
| 110-38-3 |
|
2,4-Dihydroxybenzoic acid, 97%
| 89-86-1 |
|
|