**** SECTION 2 - COMPOSITION, INFORMATION ON INGREDIENTS ****
+----------------+--------------------------------------+----------+-----------+
| CAS# | Chemical Name | % | EINECS# |
|----------------|--------------------------------------|----------|-----------|
| 462-95-3 |Diethoxymethane | 99 | 207-330-6 |
+----------------+--------------------------------------+----------+-----------+
Hazard Symbols: XI F
Risk Phrases: 11 36/37/38
**** SECTION 3 - HAZARDS IDENTIFICATION ****
EMERGENCY OVERVIEW
Highly flammable. Irritating to eyes, respiratory system and
skin.Highly flammable.The toxicological properties of this material
have not been fully investigated.
Potential Health Effects
Eye:
Causes eye irritation.
Skin:
Causes skin irritation. The toxicological properties of this
material have not been fully investigated.
Ingestion:
Causes gastrointestinal irritation with nausea, vomiting and
diarrhea. The toxicological properties of this substance have not
been fully investigated.
Inhalation:
Causes respiratory tract irritation. The toxicological properties of
this substance have not been fully investigated. Vapors may cause
dizziness or suffocation.
Chronic:
No information found.
**** SECTION 4 - FIRST AID MEASURES ****
Eyes:
Flush eyes with plenty of water for at least 15 minutes,
occasionally lifting the upper and lower eyelids. Get medical aid.
Skin:
Get medical aid. Flush skin with plenty of water for at least 15
minutes while removing contaminated clothing and shoes. Wash clothing
before reuse.
Ingestion:
Never give anything by mouth to an unconscious person. Get medical
aid. Do NOT induce vomiting. If conscious and alert, rinse mouth and
drink 2-4 cupfuls of milk or water.
Inhalation:
Remove from exposure and move to fresh air immediately. If not
breathing, give artificial respiration. If breathing is difficult,
give oxygen. Get medical aid.
Notes to Physician:
Treat symptomatically and supportively.
**** SECTION 5 - FIRE FIGHTING MEASURES ****
General Information:
As in any fire, wear a self-contained breathing apparatus in
pressure-demand, MSHA/NIOSH (approved or equivalent), and full
protective gear. Vapors may form an explosive mixture with air.
Vapors can travel to a source of ignition and flash back. During a
fire, irritating and highly toxic gases may be generated by thermal
decomposition or combustion. Use water spray to keep fire-exposed
containers cool. Water may be ineffective. Material is lighter than
water and a fire may be spread by the use of water. Flammable liquid
and vapor. Vapors may be heavier than air. They can spread along
the ground and collect in low or confined areas. Will be easily
ignited by heat, sparks or flame. Containers may explode if exposed
to fire.
Extinguishing Media:
For small fires, use dry chemical, carbon dioxide, water spray or
alcohol-resistant foam. Water may be ineffective. Water may spread
fire. If water is the only media available, use in flooding amounts.
For large fires, use water spray, fog or alcohol-resistant foam. Do
NOT use straight streams of water. Cool containers with flooding
quantities of water until well after fire is out.
**** SECTION 6 - ACCIDENTAL RELEASE MEASURES ****
General Information: Use proper personal protective equipment as indicated
in Section 8.
Spills/Leaks:
Absorb spill with inert material (e.g. vermiculite, sand or earth),
then place in suitable container. Avoid runoff into storm sewers and
ditches which lead to waterways. Clean up spills immediately,
observing precautions in the Protective Equipment section. Scoop up
with a nonsparking tool, then place into a suitable container for
disposal. Remove all sources of ignition. Provide ventilation.
**** SECTION 7 - HANDLING and STORAGE ****
Handling:
Wash thoroughly after handling. Ground and bond containers when
transferring material. Avoid contact with eyes, skin, and clothing.
Empty containers retain product residue, (liquid and/or vapor), and
can be dangerous. Keep container tightly closed. Keep away from
heat, sparks and flame. Avoid ingestion and inhalation. Use with
adequate ventilation. Wash clothing before reuse. Do not pressurize,
cut, weld, braze, solder, drill, grind, or expose empty containers
to heat, sparks or open flames.
Storage:
Keep away from heat, sparks, and flame. Store in a tightly closed
container. Store in a cool, dry, well-ventilated area away from
incompatible substances. Flammables-area.
**** SECTION 8 - EXPOSURE CONTROLS, PERSONAL PROTECTION ****
Engineering Controls:
Facilities storing or utilizing this material should be equipped
with an eyewash facility and a safety shower. Use adequate
ventilation to keep airborne concentrations low.
Exposure Limits
CAS# 462-95-3:
Personal Protective Equipment
Eyes:
Wear appropriate protective eyeglasses or chemical
safety goggles as described by OSHA's eye and face
protection regulations in 29 CFR 1910.133 or European
Standard EN166.
Skin:
Wear appropriate gloves to prevent skin exposure.
Clothing:
Wear appropriate protective clothing to prevent skin
exposure.
Respirators:
Follow the OSHA respirator regulations found in 29
CFR 1910.134 or European Standard EN 149. Use a
NIOSH/MSHA or European Standard EN 149 approved
respirator if exposure limits are exceeded or if
irritation or other symptoms are experienced.
**** SECTION 9 - PHYSICAL AND CHEMICAL PROPERTIES ****
Physical State: Liquid
Color: clear, colorless
Odor: None reported.
pH: Not available.
Vapor Pressure: 60 mmHg @ 25 C
Viscosity: Not available.
Boiling Point: 87.5 deg C @ 760.00mm Hg
Freezing/Melting Point: -66.5 deg C
Autoignition Temperature: 174 deg C ( 345.20 deg F)
Flash Point: -5 deg C ( 23.00 deg F)
Explosion Limits, lower: N/A
Explosion Limits, upper: N/A
Decomposition Temperature:
Solubility in water: soluble in benzene, chloroform
Specific Gravity/Density: .8390g/cm3
Molecular Formula: C5H12O2
Molecular Weight: 104.15
**** SECTION 10 - STABILITY AND REACTIVITY ****
Chemical Stability:
Stable at room temperature in closed containers under normal storage
and handling conditions.
Conditions to Avoid:
Incompatible materials, ignition sources, excess heat, strong
oxidants.
Incompatibilities with Other Materials:
Oxidizing agents.
Hazardous Decomposition Products:
Carbon monoxide, irritating and toxic fumes and gases, carbon
dioxide.
Hazardous Polymerization: Has not been reported.
**** SECTION 11 - TOXICOLOGICAL INFORMATION ****
RTECS#:
CAS# 462-95-3: PA8500000
LD50/LC50:
CAS# 462-95-3: Dermal, guinea pig: LD50 = 1000 mg/kg; Oral, mouse:
LD50 = 3200 mg/kg; Oral, rabbit: LD50 = 2604 mg/kg; Skin, rabbit:
LD50 = 1000 mg/kg.
Carcinogenicity:
Diethoxymethane -
Not listed by ACGIH, IARC, or NTP.
Other:
See actual entry in RTECS for complete information.
**** SECTION 12 - ECOLOGICAL INFORMATION ****
Other
No information available.
**** SECTION 13 - DISPOSAL CONSIDERATIONS ****
Dispose of in a manner consistent with federal, state, and local regulations.
**** SECTION 14 - TRANSPORT INFORMATION ****
IATA
Shipping Name: DIETHOXYMETHANE
Hazard Class: 3
UN Number: 2373
Packing Group: II
IMO
Shipping Name: DIETHOXYMETHANE
Hazard Class: 3.2
UN Number: 2373
Packing Group: II
RID/ADR
Shipping Name: DIETHOXYMETHANE
Hazard Class: 3
UN Number: 2373
Packing group: II
**** SECTION 15 - REGULATORY INFORMATION ****
European/International Regulations
European Labeling in Accordance with EC Directives
Hazard Symbols: XI F
Risk Phrases:
R 11 Highly flammable.
R 36/37/38 Irritating to eyes, respiratory system
and skin.
Safety Phrases:
S 9 Keep container in a well-ventilated place.
S 16 Keep away from sources of ignition - No
smoking.
S 26 In case of contact with eyes, rinse immediately
with plenty of water and seek medical advice.
S 28A After contact with skin, wash immediately with
plenty of water.
S 33 Take precautionary measures against static
discharges.
S 37 Wear suitable gloves.
S 37/39 Wear suitable gloves and eye/face
protection.
S 45 In case of accident or if you feel unwell, seek
medical advice immediately (show the label where
possible).
WGK (Water Danger/Protection)
CAS# 462-95-3: No information available.
Canada
CAS# 462-95-3 is listed on Canada's DSL List.
CAS# 462-95-3 is not listed on Canada's Ingredient Disclosure List.
US FEDERAL
TSCA
CAS# 462-95-3 is listed on the TSCA inventory.
**** SECTION 16 - ADDITIONAL INFORMATION ****
MSDS Creation Date: 11/05/1998 Revision #2 Date: 3/18/2003
The information above is believed to be accurate and represents the best
information currently available to us. However, we make no warranty of
merchantability or any other warranty, express or implied, with respect to
such information, and we assume no liability resulting from its use. Users
should make their own investigations to determine the suitability of the
information for their particular purposes. In no way shall the company be
liable for any claims, losses, or damages of any third party or for lost
profits or any special, indirect, incidental, consequential or exemplary
damages, howsoever arising, even if the company has been advised of
the possibility of such damages.
--------------------------------------------------------------------------------
--------------------------------------------------------------------------------
|
|
|
| ALL MSDS PAGES IN THIS GROUP
| | NAME | CAS |
|
Sodium Methoxide Titrant (0.5 M in Methanol)
| 67-56-1 |
|
Octanoic Acid, 99%
| 124-07-2 |
|
Sodium Nitrite, p.a.
| 7632-00-0 |
|
Sodium Nitrite, 99%, contains an anticakin reagent
| 7632-00-0 |
|
Sodium oxalate, pure
| 62-76-0 |
|
Sodium periodate, 99% 100g
| 7790-28-5 |
|
Sodium phosphate, dibasic heptahydrate, p.a.
| 7558-79-4 |
|
Dichloromethane-D2, 99.6+ Atom % D
| 1665-00-5 |
|
2,4-Hexanedione, 99 % (GC)
| 3002-24-2 |
|
Dichloromethane-D2, 99.6+ Atom % D, Packaged in 1.00ml Ampules
| 1665-00-5 |
|
Dichloromethane-D2, 100% D, Packaged in 0.5ml Ampules
| 1665-00-5 |
|
Salicylic Acid,Sodium Salt, 99%
| 54-21-7 |
|
Sodium Sulfate, Anhydrous, 99%
| 7757-82-6 |
|
Sodium Sulfate Crystalline, Anhydrous P.A.
| 7757-82-6 |
|
Sodium Sulfate, Anhydrous, Reagent ACS (Granular)
| 7757-82-6 |
|
Sodium Sulfite, Anhydrous, Reagent ACS (Crystals), 98+% (Titr.)
| 7757-83-7 |
|
Sodium Thiocyanate 98%(Titr., Dry)
| 540-72-7 |
|
Sodium Thiosulfate, 0.1N Standard Solution
| 7732-18-5 |
|
Sodium Thiosulfate, Pentahydrate
| 10102-17-7 |
|
Sodium Thiosulfate, Pentahydrate, Reagent ACS (Crystals)
| 10102-17-7 |
|
Sodium tungstate dihydrate, p.a.
| 10213-10-2 |
|
N-(4-Bromobutyl)-Phthalimide, 98%
| 5394-18-3 |
|
Tin(IV) chloride, anhydrous, 99%
| 7646-78-8 |
|
Tin (II) Oxide, 99+%, -100 Mesh
| 21651-19-4 |
|
Starch, Potato, Hydrolyzed for Electro-phoresis
| 9005-25-8 |
|
1-Dodecanesulfonic Acid Sodium Salt, 99+%
| 2386-53-0 |
|
Starch, Potato (Powder)
| 9005-25-8 |
|
Ethyl Propionate, 99+% (gc)
| 105-37-3 |
|
Poly(4-methyl-1-pentene), low molecular weight
| 25068-26-2 |
|
Cholic acid, 97%(tlc)
| 81-25-4 |
|
Styrene, 99%, Stabilized with 10-15 ppm p-Tert. -Butylcatechol
| 100-42-5 |
|
D(+)-sucrose, biochemical grade
| 57-50-1 |
|
Sucrose, RNase Free and DNAse Free
| 57-50-1 |
|
Sucrose, U.S.P./N.F.
| 57-50-1 |
|
Sucrose, Reagent ACS
| 57-50-1 |
|
Sulfamic Acid, p.a.
| 5329-14-6 |
|
Sulfanilic Acid, 99%
| 121-57-3 |
|
Sulfanilic Acid, Reagent ACS
| 121-57-3 |
|
Triethyl Orthoacetate, 97%
| 78-39-7 |
|
5-Sulfosalicylic acid dihydrate, 98%
| 5965-83-3 |
|
Sulfur, 99.999%, ca.12mm Pieces
| 7704-34-9 |
|
Sulfur, Sublimed, 99.5%
| 7704-34-9 |
|
Sulfuric Acid, P.A.
| 7664-93-9 |
|
Sulfuric Acid, Reagent ACS
| 7664-93-9 |
|
Tannic Acid, 95%
| 1401-55-4 |
|
L-(+)-Tartaric Acid , 99+%
| 87-69-4 |
|
Sodium Sulfide Nonahydrate, P.A.
| 1313-84-4 |
|
Tert.- Amyl Alcohol (2-Methyl-2-Butanol), 99%
| 75-85-4 |
|
Diethoxymethane, 99%
| 462-95-3 |
|
Tetrachloroethylene, 99%
| 127-18-4 |
|
|