**** SECTION 2 - COMPOSITION, INFORMATION ON INGREDIENTS ****
+----------------+--------------------------------------+----------+-----------+
| CAS# | Chemical Name | % | EINECS# |
|----------------|--------------------------------------|----------|-----------|
| 69304-37-6 |1,3-Dichloro-1,1,3,3-tetraisopropyldis| 96 | unlisted |
+----------------+--------------------------------------+----------+-----------+
Hazard Symbols: C
Risk Phrases: 34
**** SECTION 3 - HAZARDS IDENTIFICATION ****
EMERGENCY OVERVIEW
Causes burns.Moisture sensitive.
Potential Health Effects
Eye:
Causes eye burns.
Skin:
Causes skin burns.
Ingestion:
Causes gastrointestinal tract burns.
Inhalation:
May cause severe irritation of the respiratory tract with sore
throat, coughing, shortness of breath and delayed lung edema. Causes
chemical burns to the respiratory tract. Inhalation at high
concentrations may cause CNS depression and asphixiation.
Chronic:
Effects may be delayed.
**** SECTION 4 - FIRST AID MEASURES ****
Eyes:
Get medical aid immediately. Do NOT allow victim to rub eyes or keep
eyes closed. Extensive irrigation with water is required (at least 30
minutes).
Skin:
Get medical aid immediately. Immediately flush skin with plenty of
water for at least 15 minutes while removing contaminated clothing
and shoes. Wash clothing before reuse. Destroy contaminated shoes.
Ingestion:
Do not induce vomiting. If victim is conscious and alert, give 2-4
cupfuls of milk or water. Never give anything by mouth to an
unconscious person. Get medical aid immediately.
Inhalation:
Get medical aid immediately. Remove from exposure and move to fresh
air immediately. If breathing is difficult, give oxygen. Do NOT use
mouth-to-mouth resuscitation. If breathing has ceased apply
artificial respiration using oxygen and a suitable mechanical device
such as a bag and a mask.
Notes to Physician:
**** SECTION 5 - FIRE FIGHTING MEASURES ****
General Information:
As in any fire, wear a self-contained breathing apparatus in
pressure-demand, MSHA/NIOSH (approved or equivalent), and full
protective gear. During a fire, irritating and highly toxic gases
may be generated by thermal decomposition or combustion. Use water
spray to keep fire-exposed containers cool. Combustible liquid.
Vapors may be heavier than air. They can spread along the ground and
collect in low or confined areas. Containers may explode when heated.
Extinguishing Media:
In case of fire, use water, dry chemical, chemical foam, or
alcohol-resistant foam. Use water spray to cool fire-exposed
containers. Use agent most appropriate to extinguish fire. Do NOT get
water inside containers.
**** SECTION 6 - ACCIDENTAL RELEASE MEASURES ****
General Information: Use proper personal protective equipment as indicated
in Section 8.
Spills/Leaks:
Absorb spill with inert material (e.g. vermiculite, sand or earth),
then place in suitable container. Clean up spills immediately,
observing precautions in the Protective Equipment section. Remove all
sources of ignition. Use a spark-proof tool. Provide ventilation. Do
not get water inside containers.
**** SECTION 7 - HANDLING and STORAGE ****
Handling:
Wash thoroughly after handling. Remove contaminated clothing and
wash before reuse. Use only in a well-ventilated area. Do not breathe
dust, vapor, mist, or gas. Do not get in eyes, on skin, or on
clothing. Empty containers retain product residue, (liquid and/or
vapor), and can be dangerous. Keep container tightly closed. Keep
away from heat, sparks and flame. Do not ingest or inhale. Do not
allow contact with water. Discard contaminated shoes. Do not
pressurize, cut, weld, braze, solder, drill, grind, or expose empty
containers to heat, sparks or open flames. Keep from contact with
moist air and steam.
Storage:
Keep away from heat, sparks, and flame. Keep away from sources of
ignition. Keep container closed when not in use. Store in a tightly
closed container. Store in a cool, dry, well-ventilated area away
from incompatible substances. Corrosives area. Store protected from
moisture.
**** SECTION 8 - EXPOSURE CONTROLS, PERSONAL PROTECTION ****
Engineering Controls:
Facilities storing or utilizing this material should be equipped
with an eyewash facility and a safety shower. Use adequate general or
local explosion-proof ventilation to keep airborne levels to
acceptable levels.
Exposure Limits
CAS# 69304-37-6:
United Kingdom, WEL - TWA: (listed as silica, amorphous): 6 mg/m3
(inhalable dust); 2.4 mg/m3 TWA (respirable dust)
United Kingdom, WEL - STEL: (listed as silica, amorphous): 18 mg/
STEL (inhalable dust); 7.2 mg/m3 STEL (respirable dust)
Russia: (listed as silica, amorphous): 1 mg/m3 TWA
Personal Protective Equipment
Eyes:
Wear chemical splash goggles.
Skin:
Wear appropriate protective gloves to prevent skin
exposure.
Clothing:
Wear appropriate protective clothing to prevent skin
exposure.
Respirators:
A respiratory protection program that meets OSHA's 29
CFR 1910.134 and ANSI Z88.2 requirements or European
Standard EN 149 must be followed whenever workplace
conditions warrant respirator use.
**** SECTION 9 - PHYSICAL AND CHEMICAL PROPERTIES ****
Physical State: Liquid
Color: clear, colorless
Odor: None reported.
pH: Not available.
Vapor Pressure: Not available.
Viscosity: Not available.
Boiling Point: 120 deg C @ 15 mmHg
Freezing/Melting Point: Not available.
Autoignition Temperature: Not applicable.
Flash Point: 76 deg C ( 168.80 deg F)
Explosion Limits, lower: Not available.
Explosion Limits, upper: Not available.
Decomposition Temperature:
Solubility in water: Decomposes.
Specific Gravity/Density: 1.000 g/ml
Molecular Formula: C12H28Cl2OSi2
Molecular Weight: 315.42
**** SECTION 10 - STABILITY AND REACTIVITY ****
Chemical Stability:
Stable under normal temperatures and pressures.
Conditions to Avoid:
Ignition sources, moisture, excess heat.
Incompatibilities with Other Materials:
Strong oxidizing agents, moisture.
Hazardous Decomposition Products:
Hydrogen chloride, carbon monoxide, irritating and toxic fumes and
gases, carbon dioxide, silicon dioxide.
Hazardous Polymerization: Has not been reported.
**** SECTION 11 - TOXICOLOGICAL INFORMATION ****
RTECS#:
CAS# 69304-37-6 unlisted.
LD50/LC50:
Not available.
Carcinogenicity:
1,3-Dichloro-1,1,3,3-tetraisopropyldisiloxane -
Not listed by ACGIH, IARC, or NTP.
**** SECTION 12 - ECOLOGICAL INFORMATION ****
**** SECTION 13 - DISPOSAL CONSIDERATIONS ****
Dispose of in a manner consistent with federal, state, and local regulations.
**** SECTION 14 - TRANSPORT INFORMATION ****
IATA
Shipping Name: CORROSIVE LIQUID, N.O.S.*
Hazard Class: 8
UN Number: 1760
Packing Group: II
IMO
Shipping Name: CORROSIVE LIQUID, N.O.S.
Hazard Class: 8
UN Number: 1760
Packing Group: II
RID/ADR
Shipping Name: CORROSIVE LIQUID, N.O.S.
Hazard Class: 8
UN Number: 1760
Packing group: II
**** SECTION 15 - REGULATORY INFORMATION ****
European/International Regulations
European Labeling in Accordance with EC Directives
Hazard Symbols: C
Risk Phrases:
R 34 Causes burns.
Safety Phrases:
S 7 Keep container tightly closed.
S 26 In case of contact with eyes, rinse immediately
with plenty of water and seek medical advice.
S 28A After contact with skin, wash immediately with
plenty of water.
WGK (Water Danger/Protection)
CAS# 69304-37-6: No information available.
Canada
CAS# 69304-37-6 is listed on Canada's DSL List.
CAS# 69304-37-6 is not listed on Canada's Ingredient Disclosure List.
US FEDERAL
TSCA
CAS# 69304-37-6 is not listed on the TSCA inventory.
It is for research and development use only.
**** SECTION 16 - ADDITIONAL INFORMATION ****
MSDS Creation Date: 9/02/1997 Revision #7 Date: 9/08/2004
The information above is believed to be accurate and represents the best
information currently available to us. However, we make no warranty of
merchantability or any other warranty, express or implied, with respect to
such information, and we assume no liability resulting from its use. Users
should make their own investigations to determine the suitability of the
information for their particular purposes. In no way shall the company be
liable for any claims, losses, or damages of any third party or for lost
profits or any special, indirect, incidental, consequential or exemplary
damages, howsoever arising, even if the company has been advised of
the possibility of such damages.
--------------------------------------------------------------------------------
--------------------------------------------------------------------------------
|
|
|
| ALL MSDS PAGES IN THIS GROUP
| | NAME | CAS |
|
Sodium peroxide, p.a.
| 1313-60-6 |
|
(+)-(1S,2R)-2-Amino-1-Cyclopentanecarboxylic Acid
| 64191-14-6 |
|
1,2,3,4-Tetrahydroisoquinoline-3-carboxylic acid hydrochloride, 98%
| 35186-99-3 |
|
2-Amino-3-Chloro-5-Nitrobenzonitrile, 98%
| 20352-84-5 |
|
Sodium phosphate, dibasic heptahydrate, reagent ACS, crystals
| 7558-79-4 |
|
Adipic Acid Monomethyl Ester, 98%
| 627-91-8 |
|
4-Methyl-3-nitrophenol, 98%
| 2042-14-0 |
|
6-Fluoroindole, 98%
| 399-51-9 |
|
Potassium sodium tartrate tetrahydrate, p.a.
| 6381-59-5 |
|
Methylboronic acid, 97%
| 13061-96-6 |
|
Sodium Pyrophosphate Decahydrate, P.A.
| 13472-36-1 |
|
Dotriacontane, 99% (GC)
| 544-85-4 |
|
Salicylic Acid, Sodium Salt, P.A.
| 54-21-7 |
|
Sodium sulfate, powder, anhydrous, 99%, p.a.
| 7757-82-6 |
|
4-Chlorobenzyl Chloride, 99+% (GC)
| 104-83-6 |
|
Sodium Sulfite, Anhydrous, P.A.
| 7757-83-7 |
|
Sodium Thiocyanate, Reagent ACS (Crystals)
| 540-72-7 |
|
3-Tolylboronic acid, 97%
| 17933-03-8 |
|
4-Tolylboronic acid, 97%
| 5720-05-8 |
|
4-Chlorophenylboronic Acid, 97%
| 1679-18-1 |
|
3-Fluorophenylboronic Acid, 97%
| 768-35-4 |
|
Sodium Thiosulfate, Anhydrous
| 7772-98-7 |
|
4-Carboxyphenylboronic Acid, 97%
| 14047-29-1 |
|
3-Carboxyphenylboronic acid, 98%
| 25487-66-5 |
|
2-Carboxyphenylboronic acid, 97%
| 149105-19-1 |
|
2-Methoxyphenylboronic Acid, 97%
| 5720-06-9 |
|
Hexahydro-4-Methylphthalic Anhydride, 98% Mixture of Cis and Trans
| 19438-60-9 |
|
Sodium Thiosulfate Pentahydrate, P.A.
| 10102-17-7 |
|
Sodium Tripolyphosphate, Tech., 85%
| 7758-29-4 |
|
Sodium tungstate, dihydrate, reagent acs
| 10213-10-2 |
|
Biuret, 99% (TLC)
| 108-19-0 |
|
Tin(IV) Chloride, 99.999%
| 7646-78-8 |
|
Tin (II) Chloride, Anhydrous, 98%
| 7772-99-8 |
|
Tin (II) Oxide, 98+%
| 21651-19-4 |
|
Tin (II) Sulfate, 99%
| 7488-55-3 |
|
3-Nitrophenylboronic acid, 97%
| 13331-27-6 |
|
(2S,3R)-2-Amino-3-Hydroxy-4-Methylpentanoic Acid, 99+% e.e.
| 10148-71-7 |
|
4-(Methylthio)phenylboronic acid, 97%
| 98546-51-1 |
|
Starch, mais
| 9005-25-8 |
|
Styrene, P.A., Stabilized With 10-15 ppm p-Tert-Butylcatechol
| 100-42-5 |
|
3-Thiopheneboronic acid, 97%
| 6165-69-1 |
|
1,3-Dichloro-1,1,3,3-tetraisopropyldisiloxane, 96% (GC)
| 69304-37-6 |
|
2-Thiopheneboronic acid
| 6165-68-0 |
|
1-Naphthaleneboronic Acid, 97%
| 13922-41-3 |
|
n-Hexylboronic Acid
| 16343-08-1 |
|
Sucrose
| 57-50-1 |
|
Sulfamic Acid, 98+%
| 5329-14-6 |
|
Sulfanilamide, 98%
| 63-74-1 |
|
Ethyl 2-amino-1-cyclopentene-1-carboxylate 99%
| |
|
Sulfanilic Acid, 99+%
| 121-57-3 |
|
|